| Age | Commit message (Collapse) | Author |
|---|
|
Intercept debug exception events from the controller and put them into
a devcoredump using hci devcoredump APIs. The debug exception contains
data in a TLV format and it will be parsed in userspace.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Chethan Tumkur Narayan <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Current flow interates over entire ACPI table entries looking for
Bluetooth Per Platform Antenna Gain(PPAG) entry. This patch iterates
over ACPI entries relvant to Bluetooth device only.
Fixes: c585a92b2f9c ("Bluetooth: btintel: Set Per Platform Antenna Gain(PPAG)")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Antenna gain is defined as the antenna’s ability to
increase the Tx power in a given direction. Intel
is certifying its products with fixed reference
antenna peak gain values (3/5dBi). The feature takes
into account the actual antenna gain, and increases
output power values, which results in a performance
improvement.
After firmware download is completed, driver reads from
ACPI table and configures PPAG as required. ACPI table
entry for PPAG is defined as below.
Name (PPAG, Package (0x02)
{
0x00000001,
Package (0x02)
{
0x00000012, /* Bluetooth Domain */
0x00000001 /* 1 - Enable PPAG, 0 - Disable PPAG */
}
})
btmon log:
< HCI Command: Intel Configure Per Platform Antenna Gain (0x3f|0x0219) plen 12
Mcc: 0x00000000
Selector: Enable
Delta: 0x00000000
> HCI Event: Command Complete (0x0e) plen 4
Intel Configure Per Platform Antenna Gain (0x3f|0x0219) ncmd 1
Status: Success (0x00)
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Seema Sreemantha <seema.sreemantha@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch adds the flag to identify the Intel legacy ROM products that
don't support WBS like WP and StP.
Fixes: 3df4dfbec0f29 ("Bluetooth: btintel: Move hci quirks to setup routine")
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch fixes the broken LED quirk for Intel legacy ROM devices.
To fix the LED issue that doesn't turn off immediately, the host sends
the SW RFKILL command while shutting down the interface and it puts the
devices in SW RFKILL state.
Once the device is in SW RFKILL state, it can only accept HCI_Reset to
exit from the SW RFKILL state. This patch checks the quirk for broken
LED and sends the HCI_Reset before sending the HCI_Intel_Read_Version
command.
The affected legacy ROM devices are
- 8087:07dc
- 8087:0a2a
- 8087:0aa7
Fixes: ffcba827c0a1d ("Bluetooth: btintel: Fix the LED is not turning off immediately")
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Read offload use cases supported by controller.
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch sets up set_quality_report callback for Intel to
set and reset the debug features.
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch changes the exported functions to static if they are no
longer used by others.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch refactors the setup routines for legacy and TLV based
bootloader devices to the combined setup, and move the related functions
from btusb to btintel.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds a combined set_diag functions.
It also changes the btintel_set_diag_mfg() to static since it is no
longer used by others.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Some platforms have an issue with BT LED when the interface is
down or BT radio is turned off, which takes 5 seconds to BT LED
goes off. This command turns off the BT LED immediately.
This patch sends the Intel vendor command to turn off the LED.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The some legacy ROM controllers have a bug with the first HCI command
sent to it returning number of completed commands as zero, which would
stall the command processing in the Bluetooth core.
As a workaround, send HCI Rest command first which will reset the
controller to fix the issue.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds a data structure for btintel for btintel object, and the
definition of bootloder states. It also adds macros to set/test/clear
the flags.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch refactors the setup routines for legacy ROM product into
combined setup, and move the related functions from btusb to btintel.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
There are multiple setup and shutdown functions for Intel device and the
setup function to be used is depends on the USB PID/VID, which makes
difficult to maintain the code and increases the code size.
This patch adds combined setup and shutdown functions to provide a
single entry point for all Intel devices and choose the setup functions
based on the information read with HCI_Intel_Read_Version command.
Starting from TyP device, the command and response parameters for
HCI_Intel_Read_Version command are changed even though OCF remains
same. However, the legacy devices still can handle the command without
error even if it has a extra parameter, so to simplify the flow,
the new command format is used to read the version information for
both legacy and new (tlv based) format.
Also, it also adds a routine to setup the hdev callbacks in btintel.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This moves version checks of intel_version() to btintel_version_info().
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This moves version checks of intel_version_tlv() to btintel_version_info_tlv().
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This checks the firmware build number, week and year against the
repective loaded version. If details are a match, skip the download
process.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Define a new function to construct firmware/ddc filename for new
generation Intel controllers
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code should
always use “flexible array members”[1] for these cases. The older style of
one-element or zero-length arrays should no longer be used[2].
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9/process/deprecated.html#zero-length-and-one-element-arrays
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
New generation controllers supports ECDSA secure boot engine.
This patch adds,
1) function to send ECDSA header
2) function to download complete firmware for new generation Intel
controllers
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Raghuram Hegde <raghuram.hegde@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
New generation Intel controllers returns version information in TLV
format. This patch adds,
1) Enums, structures for TLV
2) function to read controller information, parse TLV data and populate
intel_version_tlv structure
3) function to print version information
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Raghuram Hegde <raghuram.hegde@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch shall enable the Intel telemetry exception format
based on the supported features
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Ps AyappadasX <AyappadasX.Ps@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The command shall read the Intel controller supported
debug feature. Based on the supported features additional debug
configuration shall be enabled.
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Ps AyappadasX <AyappadasX.Ps@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When building with Clang and CONFIG_BT_INTEL unset, the following error
occurs:
In file included from drivers/bluetooth/hci_ldisc.c:34:
drivers/bluetooth/btintel.h:188:2: error: void function
'btintel_reset_to_bootloader' should not return a value [-Wreturn-type]
return -EOPNOTSUPP;
^ ~~~~~~~~~~~
1 error generated.
Remove the unneeded return statement to fix this.
Fixes: b9a2562f4918 ("Bluetooth: btusb: Trigger Intel FW download error recovery")
Link: https://github.com/ClangBuiltLinux/linux/issues/743
Reported-by: <ci_notify@linaro.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Sometimes during FW data download stage, in case of an error is
encountered the controller device could not be recovered. To recover
from such failures send Intel hard Reset to re-trigger FW download in
following error scenarios:
1. Intel Read version command error
2. Firmware download timeout
3. Failure in Intel Soft Reset for switching to operational FW
4. Boot timeout for switching to operaional FW
Signed-off-by: Raghuram Hegde <raghuram.hegde@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The firmware download flow for RAM SKU is same for both USB and UART
and this patch creates a common function for both driver.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Intel_Read_Boot_Params command is used to read boot parameters
from the bootloader and this is Intel generic command used in USB
and UART drivers.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Intel_Reset command is used to reset the device after downloading
the firmware and this is Intel generic command used in both USB and
UART.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Intel Version Read command is used to retrieve information
about hardware and firmware version/revision of Intel Bluetooth
controllers. This is an Intel generic command used in USB and
UART drivers.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Older Intel controllers need to enter manufacturing mode to perform
some vendor specific operations (patching, configuration...).
Add enter/exit manufaturing methods and refactor existing
manufacturing code.
Exit can be configured to perform a reset. Reset can be performed
either with patches activated or deactivated.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Intel Bluetooth controllers can emit extra vendor specific events in
error conditions or for debugging purposes. To make the life easier for
engineers, enable them by default. When the vendor_diag options has been
enabled, then additional debug events are also enabled.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
For the older controllers like Wilkens Peak and Stone Peak, enabling the
traces requires to switch into manufacturer mode first. This patch does
exactly that, but only for these older controllers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
For Intel controllers with firmware that allows tracing of baseband
functionality this allows enabling it via set_diag driver callback.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Add regmap ibt to support Intel Bluetooth silicon register access
over HCI. Intel BT/FM combo chip allows to read/write some registers
(e.g. FM registers) via its HCI interface.
Read/Write operations are performed via a HCI transaction composed of
a HCI command (host->controller) followed by a HCI command complete
event (controller->host). Read/Write Command opcodes can be specified
to the regmap init function.
We define data formats which are intel/vendor specific.
Register Read/Write HCI command payload (Host):
Field: | REG ADDR | MODE | DATA_LEN | DATA... |
size: | 32b | 8b | 8b | 8b* |
Register Read HCI command complete event payload (Controller):
Field: | CMD STATUS | REG ADDR | DATA... |
size: | 8b | 32b | 8b* |
Register Write HCI command complete event payload (Controller):
Field: | CMD_STATUS |
size: | 8b |
Since this payload is HCI encapsulated, Little Endian byte order is
used.
Write/Read Example:
If we write 0x0000002a at address 0x00008c04, with opcode_write 0xfc5d,
The resulting transaction is (btmon trace):
< HCI Command (0x3f|0x005d) plen 10 [hci0]
04 8c 00 00 02 04 2a 00 00 00
> HCI Event (0x0e) plen 4
Unknown (0x3f|0x005d) ncmd 1
00
Then, if we read the same register with opcode_read 0xfc5e:
< HCI Command (0x3f|0x005e) plen 6 [hci0]
04 8c 00 00 02 04
> HCI Event (0x0e) plen 12 [hci0]
Unknown (0x3f|0x005e) ncmd 1
00 04 8c 00 00 2a 00 00 00
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
btintel_load_ddc_config retrieves the ddc file and sends its content
via DDC commands (opcode 0xfc8b).
The ddc file should contain one or more DDC structures.
A DDC structure is composed of the folowing fields:
field: | DDC LEN | DDC ID | DDC VALUE |
size: | 1 byte | 2 bytes | DDC LEN - 2 |
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Fix compilation the following compilation warning, which happens when
CONFIG_BT_INTEL is not set:
drivers/bluetooth/btintel.h:98:13: warning: ‘btintel_version_info’
defined but not used [-Wunused-function]
static void btintel_version_info(struct hci_dev *hdev,
struct intel_version *ver)
^
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Intel version information is shared between USB and UART drivers
and with that move it into a generic function of the Intel module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The Intel Secure Send command is used the same in USB and UART drivers
and with that move a generic version into the Intel module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The handling of hardware error has support for providing a vendor
specific callback to deal with the error. Move the Intel specific
function out of the USB driver into the generic module so that it
can also be utilized by the UART driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The Intel vendors events indicating firmware loading result and the
bootup of the operational firmware are currently hardcoded byte
comparisons. So intead of doing that, provide proper data structures
and actually use them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Since the Intel Bluetooth support has its own header, it makes sense
to move all command structs into it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The majority of Intel Bluetooth vendor commands are shared between USB
and UART transports. This creates a separate module that eventually
will hold all Intel specific commands, but for now just start with the
commands to change the Bluetooth public address and check for the
default address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
