| Age | Commit message (Collapse) | Author |
|---|
|
The next commit will make the way of passing CONFIG options more robust.
Unfortunately, it would uncover another hidden issue; without this
commit, skiroot_defconfig would be broken like this:
| WRAP arch/powerpc/boot/zImage.pseries
| arch/powerpc/boot/wrapper.a(decompress.o): In function `bcj_powerpc.isra.10':
| decompress.c:(.text+0x720): undefined reference to `get_unaligned_be32'
| decompress.c:(.text+0x7a8): undefined reference to `put_unaligned_be32'
| make[1]: *** [arch/powerpc/boot/Makefile;383: arch/powerpc/boot/zImage.pseries] Error 1
| make: *** [arch/powerpc/Makefile;295: zImage] Error 2
skiroot_defconfig is the only defconfig that enables CONFIG_KERNEL_XZ
for ppc, which has never been correctly built before.
I figured out the root cause in lib/decompress_unxz.c:
| #ifdef CONFIG_PPC
| # define XZ_DEC_POWERPC
| #endif
CONFIG_PPC is undefined here in the ppc bootwrapper because autoconf.h
is not included except by arch/powerpc/boot/serial.c
XZ_DEC_POWERPC is not defined, therefore, bcj_powerpc() is not compiled
for the bootwrapper.
With the next commit passing CONFIG_PPC correctly, we would realize that
{get,put}_unaligned_be32 was missing.
Unlike the other decompressors, the ppc bootwrapper duplicates all the
necessary helpers in arch/powerpc/boot/.
The other architectures define __KERNEL__ and pull in helpers for
building the decompressors.
If ppc bootwrapper had defined __KERNEL__, lib/xz/xz_private.h would
have included <asm/unaligned.h>:
| #ifdef __KERNEL__
| # include <linux/xz.h>
| # include <linux/kernel.h>
| # include <asm/unaligned.h>
However, doing so would cause tons of definition conflicts since the
bootwrapper has duplicated everything.
I just added copies of {get,put}_unaligned_be32, following the
bootwrapper coding convention.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190705100144.28785-1-yamada.masahiro@socionext.com
|
|
When CONFIG_PPC_IRQ_SOFT_MASK_DEBUG is enabled (uncommon), we have a
series of WARN_ON's in arch_local_irq_restore().
These are "should never happen" conditions, but if they do happen they
can flood the console and render the system unusable. So switch them
to WARN_ON_ONCE().
Fixes: e2b36d591720 ("powerpc/64: Don't trace code that runs with the soft irq mask unreconciled")
Fixes: 9b81c0211c24 ("powerpc/64s: make PACA_IRQ_HARD_DIS track MSR[EE] closely")
Fixes: 7c0482e3d055 ("powerpc/irq: Fix another case of lazy IRQ state getting out of sync")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190708061046.7075-1-mpe@ellerman.id.au
|
|
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update PCI and ACPI power management (improved handling of ACPI
power resources and PCIe link delays, fixes related to corner cases,
hibernation handling rework), fix and extend the operating performance
points (OPP) framework, add new cpufreq drivers for Raspberry Pi and
imx8m chips, update some other cpufreq drivers, clean up assorted
pieces of PM code and documentation and update tools.
Specifics:
- Improve the handling of shared ACPI power resources in the PCI bus
type layer (Mika Westerberg).
- Make the PCI layer take link delays required by the PCIe spec into
account as appropriate and avoid polling devices in D3cold for PME
(Mika Westerberg).
- Fix some corner case issues in ACPI device power management and in
the PCI bus type layer, optimiza and clean up the handling of
runtime-suspended PCI devices during system-wide transitions to
sleep states (Rafael Wysocki).
- Rework hibernation handling in the ACPI core and the PCI bus type
to resume runtime-suspended devices before hibernation (which
allows some functional problems to be avoided) and fix some ACPI
power management issues related to hiberation (Rafael Wysocki).
- Extend the operating performance points (OPP) framework to support
a wider range of devices (Rajendra Nayak, Stehpen Boyd).
- Fix issues related to genpd_virt_devs and issues with platforms
using the set_opp() callback in the OPP framework (Viresh Kumar,
Dmitry Osipenko).
- Add new cpufreq driver for Raspberry Pi (Nicolas Saenz Julienne).
- Add new cpufreq driver for imx8m and imx7d chips (Leonard Crestez).
- Fix and clean up the pcc-cpufreq, brcmstb-avs-cpufreq, s5pv210, and
armada-37xx cpufreq drivers (David Arcari, Florian Fainelli, Paweł
Chmiel, YueHaibing).
- Clean up and fix the cpufreq core (Viresh Kumar, Daniel Lezcano).
- Fix minor issue in the ACPI system sleep support code and export
one function from it (Lenny Szubowicz, Dexuan Cui).
- Clean up assorted pieces of PM code and documentation (Kefeng Wang,
Andy Shevchenko, Bart Van Assche, Greg Kroah-Hartman, Fuqian Huang,
Geert Uytterhoeven, Mathieu Malaterre, Rafael Wysocki).
- Update the pm-graph utility to v5.4 (Todd Brandt).
- Fix and clean up the cpupower utility (Abhishek Goel, Nick Black)"
* tag 'pm-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (57 commits)
ACPI: PM: Make acpi_sleep_state_supported() non-static
PM: sleep: Drop dev_pm_skip_next_resume_phases()
ACPI: PM: Unexport acpi_device_get_power()
Documentation: ABI: power: Add missing newline at end of file
ACPI: PM: Drop unused function and function header
ACPI: PM: Introduce "poweroff" callbacks for ACPI PM domain and LPSS
ACPI: PM: Simplify and fix PM domain hibernation callbacks
PCI: PM: Simplify bus-level hibernation callbacks
PM: ACPI/PCI: Resume all devices during hibernation
cpufreq: Avoid calling cpufreq_verify_current_freq() from handle_update()
cpufreq: Consolidate cpufreq_update_current_freq() and __cpufreq_get()
kernel: power: swap: use kzalloc() instead of kmalloc() followed by memset()
cpufreq: Don't skip frequency validation for has_target() drivers
PCI: PM/ACPI: Refresh all stale power state data in pci_pm_complete()
PCI / ACPI: Add _PR0 dependent devices
ACPI / PM: Introduce concept of a _PR0 dependent device
PCI / ACPI: Use cached ACPI device state to get PCI device power state
ACPI: PM: Allow transitions to D0 to occur in special cases
ACPI: PM: Avoid evaluating _PS3 on transitions from D3hot to D3cold
cpufreq: Use has_target() instead of !setpolicy
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull force_sig() argument change from Eric Biederman:
"A source of error over the years has been that force_sig has taken a
task parameter when it is only safe to use force_sig with the current
task.
The force_sig function is built for delivering synchronous signals
such as SIGSEGV where the userspace application caused a synchronous
fault (such as a page fault) and the kernel responded with a signal.
Because the name force_sig does not make this clear, and because the
force_sig takes a task parameter the function force_sig has been
abused for sending other kinds of signals over the years. Slowly those
have been fixed when the oopses have been tracked down.
This set of changes fixes the remaining abusers of force_sig and
carefully rips out the task parameter from force_sig and friends
making this kind of error almost impossible in the future"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (27 commits)
signal/x86: Move tsk inside of CONFIG_MEMORY_FAILURE in do_sigbus
signal: Remove the signal number and task parameters from force_sig_info
signal: Factor force_sig_info_to_task out of force_sig_info
signal: Generate the siginfo in force_sig
signal: Move the computation of force into send_signal and correct it.
signal: Properly set TRACE_SIGNAL_LOSE_INFO in __send_signal
signal: Remove the task parameter from force_sig_fault
signal: Use force_sig_fault_to_task for the two calls that don't deliver to current
signal: Explicitly call force_sig_fault on current
signal/unicore32: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from ptrace_break
signal/nds32: Remove tsk parameter from send_sigtrap
signal/riscv: Remove tsk parameter from do_trap
signal/sh: Remove tsk parameter from force_sig_info_fault
signal/um: Remove task parameter from send_sigtrap
signal/x86: Remove task parameter from send_sigtrap
signal: Remove task parameter from force_sig_mceerr
signal: Remove task parameter from force_sig
signal: Remove task parameter from force_sigsegv
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
- Remove the unused per rq load array and all its infrastructure, by
Dietmar Eggemann.
- Add utilization clamping support by Patrick Bellasi. This is a
refinement of the energy aware scheduling framework with support for
boosting of interactive and capping of background workloads: to make
sure critical GUI threads get maximum frequency ASAP, and to make
sure background processing doesn't unnecessarily move to cpufreq
governor to higher frequencies and less energy efficient CPU modes.
- Add the bare minimum of tracepoints required for LISA EAS regression
testing, by Qais Yousef - which allows automated testing of various
power management features, including energy aware scheduling.
- Restructure the former tsk_nr_cpus_allowed() facility that the -rt
kernel used to modify the scheduler's CPU affinity logic such as
migrate_disable() - introduce the task->cpus_ptr value instead of
taking the address of &task->cpus_allowed directly - by Sebastian
Andrzej Siewior.
- Misc optimizations, fixes, cleanups and small enhancements - see the
Git log for details.
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
sched/uclamp: Add uclamp support to energy_compute()
sched/uclamp: Add uclamp_util_with()
sched/cpufreq, sched/uclamp: Add clamps for FAIR and RT tasks
sched/uclamp: Set default clamps for RT tasks
sched/uclamp: Reset uclamp values on RESET_ON_FORK
sched/uclamp: Extend sched_setattr() to support utilization clamping
sched/core: Allow sched_setattr() to use the current policy
sched/uclamp: Add system default clamps
sched/uclamp: Enforce last task's UCLAMP_MAX
sched/uclamp: Add bucket local max tracking
sched/uclamp: Add CPU's clamp buckets refcounting
sched/fair: Rename weighted_cpuload() to cpu_runnable_load()
sched/debug: Export the newly added tracepoints
sched/debug: Add sched_overutilized tracepoint
sched/debug: Add new tracepoint to track PELT at se level
sched/debug: Add new tracepoints to track PELT at rq level
sched/debug: Add a new sched_trace_*() helper functions
sched/autogroup: Make autogroup_path() always available
sched/wait: Deduplicate code with do-while
sched/topology: Remove unused 'sd' parameter from arch_scale_cpu_capacity()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
"The main changes in this cycle are:
- rwsem scalability improvements, phase #2, by Waiman Long, which are
rather impressive:
"On a 2-socket 40-core 80-thread Skylake system with 40 reader
and writer locking threads, the min/mean/max locking operations
done in a 5-second testing window before the patchset were:
40 readers, Iterations Min/Mean/Max = 1,807/1,808/1,810
40 writers, Iterations Min/Mean/Max = 1,807/50,344/151,255
After the patchset, they became:
40 readers, Iterations Min/Mean/Max = 30,057/31,359/32,741
40 writers, Iterations Min/Mean/Max = 94,466/95,845/97,098"
There's a lot of changes to the locking implementation that makes
it similar to qrwlock, including owner handoff for more fair
locking.
Another microbenchmark shows how across the spectrum the
improvements are:
"With a locking microbenchmark running on 5.1 based kernel, the
total locking rates (in kops/s) on a 2-socket Skylake system
with equal numbers of readers and writers (mixed) before and
after this patchset were:
# of Threads Before Patch After Patch
------------ ------------ -----------
2 2,618 4,193
4 1,202 3,726
8 802 3,622
16 729 3,359
32 319 2,826
64 102 2,744"
The changes are extensive and the patch-set has been through
several iterations addressing various locking workloads. There
might be more regressions, but unless they are pathological I
believe we want to use this new implementation as the baseline
going forward.
- jump-label optimizations by Daniel Bristot de Oliveira: the primary
motivation was to remove IPI disturbance of isolated RT-workload
CPUs, which resulted in the implementation of batched jump-label
updates. Beyond the improvement of the real-time characteristics
kernel, in one test this patchset improved static key update
overhead from 57 msecs to just 1.4 msecs - which is a nice speedup
as well.
- atomic64_t cross-arch type cleanups by Mark Rutland: over the last
~10 years of atomic64_t existence the various types used by the
APIs only had to be self-consistent within each architecture -
which means they became wildly inconsistent across architectures.
Mark puts and end to this by reworking all the atomic64
implementations to use 's64' as the base type for atomic64_t, and
to ensure that this type is consistently used for parameters and
return values in the API, avoiding further problems in this area.
- A large set of small improvements to lockdep by Yuyang Du: type
cleanups, output cleanups, function return type and othr cleanups
all around the place.
- A set of percpu ops cleanups and fixes by Peter Zijlstra.
- Misc other changes - please see the Git log for more details"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (82 commits)
locking/lockdep: increase size of counters for lockdep statistics
locking/atomics: Use sed(1) instead of non-standard head(1) option
locking/lockdep: Move mark_lock() inside CONFIG_TRACE_IRQFLAGS && CONFIG_PROVE_LOCKING
x86/jump_label: Make tp_vec_nr static
x86/percpu: Optimize raw_cpu_xchg()
x86/percpu, sched/fair: Avoid local_clock()
x86/percpu, x86/irq: Relax {set,get}_irq_regs()
x86/percpu: Relax smp_processor_id()
x86/percpu: Differentiate this_cpu_{}() and __this_cpu_{}()
locking/rwsem: Guard against making count negative
locking/rwsem: Adaptive disabling of reader optimistic spinning
locking/rwsem: Enable time-based spinning on reader-owned rwsem
locking/rwsem: Make rwsem->owner an atomic_long_t
locking/rwsem: Enable readers spinning on writer
locking/rwsem: Clarify usage of owner's nonspinaable bit
locking/rwsem: Wake up almost all readers in wait queue
locking/rwsem: More optimal RT task handling of null owner
locking/rwsem: Always release wait_lock before waking up tasks
locking/rwsem: Implement lock handoff to prevent lock starvation
locking/rwsem: Make rwsem_spin_on_owner() return owner state
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP/hotplug updates from Thomas Gleixner:
"A small set of updates for SMP and CPU hotplug:
- Abort disabling secondary CPUs in the freezer when a wakeup is
pending instead of evaluating it only after all CPUs have been
offlined.
- Remove the shared annotation for the strict per CPU cfd_data in the
smp function call core code.
- Remove the return values of smp_call_function() and on_each_cpu()
as they are unconditionally 0. Fixup the few callers which actually
bothered to check the return value"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp: Remove smp_call_function() and on_each_cpu() return values
smp: Do not mark call_function_data as shared
cpu/hotplug: Abort disabling secondary CPUs if wakeup is pending
cpu/hotplug: Fix notify_cpu_starting() reference in bringup_wait_for_ap()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Improve stop_machine wait logic: replace cpu_relax_yield call in
generic stop_machine function with a weak stop_machine_yield
function. This is overridden on s390, which yields the current cpu to
the neighbouring cpu after a couple of retries, instead of blindly
giving up the cpu to the hipervisor. This significantly improves
stop_machine performance on s390 in overcommitted scenarios.
This includes common code changes which have been Acked by Peter
Zijlstra and Thomas Gleixner.
- Improve jump label transformation speed: transform jump labels
without using stop_machine.
- Refactoring of the vfio-ccw cp handling, simplifying the code and
avoiding unneeded allocating/copying.
- Various vfio-ccw fixes (ccw translation, state machine).
- Add support for vfio-ap queue interrupt control in the guest. This
includes s390 kvm changes which have been Acked by Christian
Borntraeger.
- Add protected virtualization support for virtio-ccw.
- Enforce both CONFIG_SMP and CONFIG_HOTPLUG_CPU, which allows to
remove some code which most likely isn't working at all, besides that
s390 didn't even compile for !CONFIG_SMP.
- Support for special flagged EP11 CPRBs for zcrypt.
- Handle PCI devices with no support for new MIO instructions.
- Avoid KASAN false positives in reworked stack unwinder.
- Couple of fixes for the QDIO layer.
- Convert s390 specific documentation to ReST format.
- Let s390 crypto modules return -ENODEV instead of -EOPNOTSUPP if
hardware is missing. This way our modules behave like most other
modules and which is also what systemd's systemd-modules-load.service
expects.
- Replace defconfig with performance_defconfig, so there is one config
file less to maintain.
- Remove the SCLP call home device driver, which was never useful.
- Cleanups all over the place.
* tag 's390-5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (83 commits)
docs: s390: s390dbf: typos and formatting, update crash command
docs: s390: unify and update s390dbf kdocs at debug.c
docs: s390: restore important non-kdoc parts of s390dbf.rst
vfio-ccw: Fix the conversion of Format-0 CCWs to Format-1
s390/pci: correctly handle MIO opt-out
s390/pci: deal with devices that have no support for MIO instructions
s390: ap: kvm: Enable PQAP/AQIC facility for the guest
s390: ap: implement PAPQ AQIC interception in kernel
vfio: ap: register IOMMU VFIO notifier
s390: ap: kvm: add PQAP interception for AQIC
s390/unwind: cleanup unused READ_ONCE_TASK_STACK
s390/kasan: avoid false positives during stack unwind
s390/qdio: don't touch the dsci in tiqdio_add_input_queues()
s390/qdio: (re-)initialize tiqdio list entries
s390/dasd: Fix a precision vs width bug in dasd_feature_list()
s390/cio: introduce driver_override on the css bus
vfio-ccw: make convert_ccw0_to_ccw1 static
vfio-ccw: Remove copy_ccw_from_iova()
vfio-ccw: Factor out the ccw0-to-ccw1 transition
vfio-ccw: Copy CCW data outside length calculation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- arm64 support for syscall emulation via PTRACE_SYSEMU{,_SINGLESTEP}
- Wire up VM_FLUSH_RESET_PERMS for arm64, allowing the core code to
manage the permissions of executable vmalloc regions more strictly
- Slight performance improvement by keeping softirqs enabled while
touching the FPSIMD/SVE state (kernel_neon_begin/end)
- Expose a couple of ARMv8.5 features to user (HWCAP): CondM (new
XAFLAG and AXFLAG instructions for floating point comparison flags
manipulation) and FRINT (rounding floating point numbers to integers)
- Re-instate ARM64_PSEUDO_NMI support which was previously marked as
BROKEN due to some bugs (now fixed)
- Improve parking of stopped CPUs and implement an arm64-specific
panic_smp_self_stop() to avoid warning on not being able to stop
secondary CPUs during panic
- perf: enable the ARM Statistical Profiling Extensions (SPE) on ACPI
platforms
- perf: DDR performance monitor support for iMX8QXP
- cache_line_size() can now be set from DT or ACPI/PPTT if provided to
cope with a system cache info not exposed via the CPUID registers
- Avoid warning on hardware cache line size greater than
ARCH_DMA_MINALIGN if the system is fully coherent
- arm64 do_page_fault() and hugetlb cleanups
- Refactor set_pte_at() to avoid redundant READ_ONCE(*ptep)
- Ignore ACPI 5.1 FADTs reported as 5.0 (infer from the
'arm_boot_flags' introduced in 5.1)
- CONFIG_RANDOMIZE_BASE now enabled in defconfig
- Allow the selection of ARM64_MODULE_PLTS, currently only done via
RANDOMIZE_BASE (and an erratum workaround), allowing modules to spill
over into the vmalloc area
- Make ZONE_DMA32 configurable
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (54 commits)
perf: arm_spe: Enable ACPI/Platform automatic module loading
arm_pmu: acpi: spe: Add initial MADT/SPE probing
ACPI/PPTT: Add function to return ACPI 6.3 Identical tokens
ACPI/PPTT: Modify node flag detection to find last IDENTICAL
x86/entry: Simplify _TIF_SYSCALL_EMU handling
arm64: rename dump_instr as dump_kernel_instr
arm64/mm: Drop [PTE|PMD]_TYPE_FAULT
arm64: Implement panic_smp_self_stop()
arm64: Improve parking of stopped CPUs
arm64: Expose FRINT capabilities to userspace
arm64: Expose ARMv8.5 CondM capability to userspace
arm64: defconfig: enable CONFIG_RANDOMIZE_BASE
arm64: ARM64_MODULES_PLTS must depend on MODULES
arm64: bpf: do not allocate executable memory
arm64/kprobes: set VM_FLUSH_RESET_PERMS on kprobe instruction pages
arm64/mm: wire up CONFIG_ARCH_HAS_SET_DIRECT_MAP
arm64: module: create module allocations without exec permissions
arm64: Allow user selection of ARM64_MODULE_PLTS
acpi/arm64: ignore 5.1 FADTs that are reported as 5.0
arm64: Allow selecting Pseudo-NMI again
...
|
|
* pm-sleep:
PM: sleep: Drop dev_pm_skip_next_resume_phases()
ACPI: PM: Drop unused function and function header
ACPI: PM: Introduce "poweroff" callbacks for ACPI PM domain and LPSS
ACPI: PM: Simplify and fix PM domain hibernation callbacks
PCI: PM: Simplify bus-level hibernation callbacks
PM: ACPI/PCI: Resume all devices during hibernation
kernel: power: swap: use kzalloc() instead of kmalloc() followed by memset()
PM: sleep: Update struct wakeup_source documentation
drivers: base: power: remove wakeup_sources_stats_dentry variable
PM: suspend: Rename pm_suspend_via_s2idle()
PM: sleep: Show how long dpm_suspend_start() and dpm_suspend_end() take
PM: hibernate: powerpc: Expose pfn_is_nosave() prototype
|
|
To increase readability/maintainability, replace hard coded
instructions values by symbolic names.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Fix R_PPC64_ENTRY case, the addi reads from r2 not r12]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
To increase readability/maintainability, replace hard coded
instructions values by symbolic names.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
PPC_HA() PPC_HI() and PPC_LO() macros are nice macros. Move them
from module64.c to ppc-opcode.h in order to use them in other places.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Clean up formatting in new code, drop duplicates in ftrace.c]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The comment here is wrong, the addi reads from r2 not r12. The code is
correct, 0x38420000 = addi r2,r2,0.
Fixes: a61674bdfc7c ("powerpc/module: Handle R_PPC64_ENTRY relocations")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This patch allows to generate lzo compressed uImage
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This patch allows to generate lzma compressed uImage
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This patch modifies the generation of uImage by handing over
the selected compression type instead of forcing gzip
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Some SCC functions like the QMC requires an extended parameter RAM.
On modern 8xx (ie 866 and 885), SPI area can already be relocated,
allowing the use of those functions on SCC2. But SCC3 and SCC4
parameter RAM collide with SMC1 and SMC2 parameter RAMs.
This patch adds microcode to allow the relocation of both SMC1 and
SMC2, and relocate them at offsets 0x1ec0 and 0x1fc0.
Those offsets are by default for the CPM1 DSP1 and DSP2, but there
is no kernel driver using them at the moment so this area can be
reused.
This microcode is provided by Freescale/NXP in Engineering Bulletin
EB662 ("MPC8xx I2C/SPI and SMC Relocation Microcode Packages")
dated 2006. The binary code is public. The source is not available.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Change microcode functions to use IO accessors and get rid
of volatile attributes.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Reduce #ifdef mess by using IS_ENABLED() instead.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The CPM registers RCCR and CPMCR1..4 registers has to be set in
accordance with the microcode patch beeing programmed. Lets
define them as part of the patch set and refactor their
programming from that definition.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Define patch name together with the patch code, and refactor
the associated printk() while replacing it by a pr_info()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add empty microcode tables so that all tables are defined
all the time. Regroup the writing of the 3 tables regardless
of the selected microcode.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Create a function to refactor the writing of CPM microcode arrays.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Compact obscure microcode arrays by putting 4 values per line
in order to reduce number of lines in the file to increase
readability.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
verify_patch() has been opted out since many years, and
the comment suggests it doesn't work. So drop it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Only 8xx selects CPM1 and related CONFIG options are already
in platforms/8xx/Kconfig
Move the related C files to platforms/8xx/.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Minor formatting fixes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This patch drops the assembly PPC64 version of flush_dcache_range()
and re-uses the PPC32 static inline version.
With GCC 8.1, the following code is generated:
void flush_test(unsigned long start, unsigned long stop)
{
flush_dcache_range(start, stop);
}
0000000000000130 <.flush_test>:
130: 3d 22 00 00 addis r9,r2,0
132: R_PPC64_TOC16_HA .data+0x8
134: 81 09 00 00 lwz r8,0(r9)
136: R_PPC64_TOC16_LO .data+0x8
138: 3d 22 00 00 addis r9,r2,0
13a: R_PPC64_TOC16_HA .data+0xc
13c: 80 e9 00 00 lwz r7,0(r9)
13e: R_PPC64_TOC16_LO .data+0xc
140: 7d 48 00 d0 neg r10,r8
144: 7d 43 18 38 and r3,r10,r3
148: 7c 00 04 ac hwsync
14c: 4c 00 01 2c isync
150: 39 28 ff ff addi r9,r8,-1
154: 7c 89 22 14 add r4,r9,r4
158: 7c 83 20 50 subf r4,r3,r4
15c: 7c 89 3c 37 srd. r9,r4,r7
160: 41 82 00 1c beq 17c <.flush_test+0x4c>
164: 7d 29 03 a6 mtctr r9
168: 60 00 00 00 nop
16c: 60 00 00 00 nop
170: 7c 00 18 ac dcbf 0,r3
174: 7c 63 42 14 add r3,r3,r8
178: 42 00 ff f8 bdnz 170 <.flush_test+0x40>
17c: 7c 00 04 ac hwsync
180: 4c 00 01 2c isync
184: 4e 80 00 20 blr
188: 60 00 00 00 nop
18c: 60 00 00 00 nop
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This patch defines C helpers to retrieve the size of
cache blocks and uses them in the cacheflush functions.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
On most arches having function flush_dcache_range(), including PPC32,
this function does a writeback and invalidation of the cache bloc.
On PPC64, flush_dcache_range() only does a writeback while
flush_inval_dcache_range() does the invalidation in addition.
In addition it looks like within arch/powerpc/, there are no PPC64
platforms using flush_dcache_range()
This patch drops the existing 64 bits version of flush_dcache_range()
and renames flush_inval_dcache_range() into flush_dcache_range().
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Cache instructions (dcbz, dcbi, dcbf and dcbst) take two registers
that are summed to obtain the target address. Using 'Z' constraint
and '%y0' argument gives GCC the opportunity to use both registers
instead of only one with the second being forced to 0.
Suggested-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This makes sure we don't enable HugeTLB if the cache is not configured.
I am still not sure about this. IMHO hugetlb support should be a hardware
support derivative and any cache allocation failure should be handled as I did
in the earlier patch. But then if we were not able to create hugetlb page table
cache, we can as well declare hugetlb support disabled thereby avoiding calling
into allocation routines.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We only check for hugetlb allocations, because with hugetlb we do conditional
registration. For PGD/PUD/PMD levels we register them always in
pgtable_cache_init.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This fixes kernel crash that arises due to not handling page table allocation
failures while allocating hugetlb page table.
Fixes: e2b3d202d1db ("powerpc: Switch 16GB and 16MB explicit hugepages to a different page table format")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Now that we have switched the page table walk to use pmd_is_leaf we can now
revert commit 8adddf349fda ("powerpc/mm/radix: Make Radix require HUGETLB_PAGE")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
large devmap usage is dependent on THP. Hence once check is sufficient.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Even when we have HugeTLB and THP disabled, kernel linear map can still be
mapped with hugepages. This is only an issue with radix translation because hash
MMU doesn't map kernel linear range in linux page table and other kernel
map areas are not mapped using hugepage.
Add config independent helpers and put WARN_ON() when we don't expect things
to be mapped via hugepages.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
device tree
We used uuid_parse to convert uuid string from device tree to two u64
components. We want to make sure we look at the uuid read from device
tree in an endian-neutral fashion. For now, I am picking little-endian
to be format so that we don't end up doing an additional conversion.
The reason to store in a specific endian format is to enable reading
the namespace created with a little-endian kernel config on a
big-endian kernel. We do store the device tree uuid string as a 64-bit
little-endian cookie in the label area. When booting the kernel we
also compare this cookie against what is read from the device tree.
For this, to work we have to store and compare these values in a CPU
endian config independent fashion.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
SCM_READ/WRITE_MEATADATA hcall supports multibyte read/write. This patch
updates the metadata read/write to use 1, 2, 4 or 8 byte read/write as
mentioned in PAPR document.
READ/WRITE_METADATA hcall supports the 1, 2, 4, or 8 bytes read/write.
For other values hcall results H_P3.
Hypervisor stores the metadata contents in big-endian format and in-order
to enable read/write in different granularity, we need to switch the contents
to big-endian before calling HCALL.
Based on an patch from Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The device tree node is documented as below:
“ibm,cache-flush-required”:
property name indicates Cache Flush Required for this Persistent Memory Segment to persist memory
prop-encoded-array: None, this is a name only property.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
block
Allocation from altmap area can fail based on vmemmap page size used.
Add kernel info message to indicate the failure. That allows the user
to identify whether they are really using persistent memory reserved
space for per-page metadata.
The message looks like:
[ 136.587212] altmap block allocation failed, falling back to system memory
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
If we fail to parse min_common_depth from device tree we boot with
numa disabled. Reflect the same by updating numa_enabled variable
to false. Also, switch all min_common_depth failure check to
if (!numa_enabled) check.
This helps us to avoid checking for both in different code paths.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
If we boot with numa=off, we need to make sure we return NUMA_NO_NODE when
looking up associativity details of resources. Without this, we hit crash
like below
BUG: Unable to handle kernel data access at 0x40000000008
Faulting instruction address: 0xc000000008f31704
cpu 0x1b: Vector: 380 (Data SLB Access) at [c00000000b9bb320]
pc: c000000008f31704: _raw_spin_lock+0x14/0x100
lr: c0000000083f41fc: ____cache_alloc_node+0x5c/0x290
sp: c00000000b9bb5b0
msr: 800000010280b033
dar: 40000000008
current = 0xc00000000b9a2700
paca = 0xc00000000a740c00 irqmask: 0x03 irq_happened: 0x01
pid = 1, comm = swapper/27
Linux version 5.2.0-rc4-00925-g74e188c620b1 (root@linux-d8ip) (gcc version 7.4.1 20190424 [gcc-7-branch revision 270538] (SUSE Linux)) #34 SMP Sat Jun 29 00:41:02 EDT 2019
enter ? for help
[link register ] c0000000083f41fc ____cache_alloc_node+0x5c/0x290
[c00000000b9bb5b0] 0000000000000dc0 (unreliable)
[c00000000b9bb5f0] c0000000083f48c8 kmem_cache_alloc_node_trace+0x138/0x360
[c00000000b9bb670] c000000008aa789c devres_alloc_node+0x4c/0xa0
[c00000000b9bb6a0] c000000008337218 devm_memremap+0x58/0x130
[c00000000b9bb6f0] c000000008aed00c devm_nsio_enable+0xdc/0x170
[c00000000b9bb780] c000000008af3b6c nd_pmem_probe+0x4c/0x180
[c00000000b9bb7b0] c000000008ad84cc nvdimm_bus_probe+0xac/0x260
[c00000000b9bb840] c000000008aa0628 really_probe+0x148/0x500
[c00000000b9bb8d0] c000000008aa0d7c driver_probe_device+0x19c/0x1d0
[c00000000b9bb950] c000000008aa11bc device_driver_attach+0xcc/0x100
[c00000000b9bb990] c000000008aa12ec __driver_attach+0xfc/0x1e0
[c00000000b9bba10] c000000008a9d0a4 bus_for_each_dev+0xb4/0x130
[c00000000b9bba70] c000000008a9fc04 driver_attach+0x34/0x50
[c00000000b9bba90] c000000008a9f118 bus_add_driver+0x1d8/0x300
[c00000000b9bbb20] c000000008aa2358 driver_register+0x98/0x1a0
[c00000000b9bbb90] c000000008ad7e6c __nd_driver_register+0x5c/0x100
[c00000000b9bbbf0] c0000000093efbac nd_pmem_driver_init+0x34/0x48
[c00000000b9bbc10] c0000000080106c0 do_one_initcall+0x60/0x2d0
[c00000000b9bbce0] c00000000938463c kernel_init_freeable+0x384/0x48c
[c00000000b9bbdb0] c000000008010a5c kernel_init+0x2c/0x160
[c00000000b9bbe20] c00000000800ba54 ret_from_kernel_thread+0x5c/0x68
Reported-and-debugged-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
If we fail to parse the associativity array we should default to
NUMA_NO_NODE instead of NODE 0. Rest of the code fallback to the
right default if we find the numa node value NUMA_NO_NODE.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We use mmu_vmemmap_psize to find the page size for mapping the vmmemap area.
With radix translation, we are suboptimally setting this value to PAGE_SIZE.
We do check for 2M page size support and update mmu_vmemap_psize to use
hugepage size but we suboptimally reset the value to PAGE_SIZE in
radix__early_init_mmu(). This resulted in always mapping vmemmap area with
64K page size.
Fixes: 2bfd65e45e87 ("powerpc/mm/radix: Add radix callbacks for early init routines")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
With hash translation and 4K PAGE_SIZE config, we need to make sure we don't
use 64K page size for vmemmap.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Since commit 0034d395f89d ("powerpc/mm/hash64: Map all the kernel
regions in the same 0xc range") __kernel_virt_size is not used
anymore.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When enabling or disabling the vcpu dispatch statistics, we do a lot of
work including allocating/deallocating memory across all possible cpus
for the DTL buffer. In order to guard against hogging the cpu for too
long, track the time we're taking and yield the processor if necessary.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
For Shared Processor LPARs, the POWER Hypervisor maintains a
relatively static mapping of the LPAR processors (vcpus) to physical
processor chips (representing the "home" node) and tries to always
dispatch vcpus on their associated physical processor chip. However,
under certain scenarios, vcpus may be dispatched on a different
processor chip (away from its home node). The actual physical
processor number on which a certain vcpu is dispatched is available to
the guest in the 'processor_id' field of each DTL entry.
The guest can discover the home node of each vcpu through the
H_HOME_NODE_ASSOCIATIVITY(flags=1) hcall. The guest can also discover
the associativity of physical processors, as represented in the DTL
entry, through the H_HOME_NODE_ASSOCIATIVITY(flags=2) hcall.
These can then be compared to determine if the vcpu was dispatched on
its home node or not. If the vcpu was not dispatched on the home node,
it is possible to determine if the vcpu was dispatched in a different
chip, socket or drawer.
Introduce a procfs file /proc/powerpc/vcpudispatch_stats that can be
used to obtain these statistics. Writing '1' to this file enables
collecting the statistics, while writing '0' disables the statistics.
The statistics themselves are available by reading the procfs file. By
default, the DTLB log for each vcpu is processed 50 times a second so
as not to miss any entries. This processing frequency can be changed
through /proc/powerpc/vcpudispatch_stats_freq.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
