| Age | Commit message (Collapse) | Author |
|---|
|
This patch drops support for AVR32 architecture from the Linux kernel.
The AVR32 architecture is not keeping up with the development of the
kernel, and since it shares so much of the drivers with Atmel ARM SoC,
it is starting to hinder these drivers to develop swiftly.
Also, all AVR32 AP7 SoC processors are end of lifed from Atmel (now
Microchip).
Finally, the GCC toolchain is stuck at version 4.2.x, and has not
received any patches since the last release from Atmel;
4.2.4-atmel.1.1.3.avr32linux.1. When building kernel v4.10, this
toolchain is no longer able to properly link the network stack.
Haavard and I have came to the conclusion that we feel keeping AVR32 on
life support offers more obstacles for Atmel ARMs, than it gives joy to
AVR32 users. I also suspect there are very few AVR32 users left today,
if anybody at all.
Signed-off-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Håvard Skinnemoen <hskinnemoen@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The ATSTK1006 is basically an upgraded version of ATSTK1002 with
128 MiB SDRAM and 256 MiB NAND flash on board.
Otherwise, the board is very similar to the ATSTK1002, so it uses the
same board support file.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Remove the CPU selection menu and instead let it be selected by the
board or daughterboard option. Add daughterboard selection for
ATSTK1000 (this was previously determined based on CPU type.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
ATSTK1003 and ATSTK1004 are CPU daughterboards for ATSTK1000 featuring
the AT32AP7001 and AT32AP7002 CPUs, respectively.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Reduce the ridiculous amount of #ifdef clutter in atstk1002.c a bit by
moving all the extdac stuff into its own function and providing an
empty stub for the case when it isn't wanted.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
There may be other boards than STK1002 that want to use the leds on
STK1000. Move it to stk1000 common code to make it easier to reuse.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Add GPIO led support: J2 to either block of LEDs on the STK1000.
This uses the new LEDS_GPIO driver, and sets up a heartbeat trigger by
default ... either bright (!!) amber, or a more interesting purple.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
This adds some STK1002-specific config options covering the jumper settings,
so the kernel can automatically be configured to include the relevant devices.
One of them replaces the previous internal SW2_DEFAULT setting; SPI config
is affected by two of the jumpers; and a fourth one switches between LCD and
the second Ethernet connector. (There's more that to be done.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
