| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Around one third of the fixes this time are for dts files that list
their ethernet controller as using 'phy-mode="rgmii"' but are changed
to 'phy-mode="rgmii-id"' now, because the PHY drivers (realtek,
ksz9031, dp83867, ...) now configure the internal delay based on that
when they used to stay on the hardware default.
The long story is archived at
https://lore.kernel.org/netdev/CAMj1kXEEF_Un-4NTaD5iUN0NoZYaJQn-rPediX0S6oRiuVuW-A@mail.gmail.com/
I was trying to hold off on the bugfixes until there was a solution
that would avoid breaking all boards, but that does not seem to be
happening any time soon, so I am now sending the correct version of
the dts files to ensure that at least these machines can use their
network devices again.
The other changes this time are:
- Updating the MAINTAINER lists for Allwinner and Samsung SoCs
- Multiple i.MX8MN machines get updates for their CPU operating
points to match the data sheet
- A revert for a dts patch that caused a regression in USB support on
Odroid U3
- Two fixes for the AMD Tee driver, addressing a memory leak and
missing locking
- Mark the network subsystem on qoriq-fman3 as cache coherent for
correctness as better performance.
- Minor dts fixes elsewhere, addressing dtc warnings and similar
problems"
* tag 'arm-soc-fixes-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: dts: exynos: revert "add input clock to CMU in Exynos4412 Odroid"
ARM: dts: imx50-evk: Fix the chip select 1 IOMUX
arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point
ARM: dts: stm32: Keep VDDA LDO1 always on on DHCOM
ARM: dts: stm32: Enable thermal sensor support on stm32mp15xx-dhcor
ARM: dts: stm32: Define VIO regulator supply on DHCOM
ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2
ARM: dts: stm32: Fix TA3-GPIO-C key on STM32MP1 DHCOM PDK2
arm64: dts: renesas: r8a774e1: Add missing audio_clk_b
tee: amdtee: synchronize access to shm list
tee: amdtee: fix memory leak due to reset of global shm list
arm64: dts: agilex/stratix10: Fix qspi node compatible
ARM: dts: imx6q-prti6q: fix PHY address
ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking
arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy
arm64: dts imx8mn: Remove non-existent USB OTG2
arm64: dts: imx8mm-beacon-som: Fix Choppy BT audio
arm64: dts: fsl: DPAA FMan DMA operations are coherent
arm64: dts: fsl: fix endianness issue of rcpm
arm64: dts: imx8mn-evk: fix missing PMIC's interrupt line pull-up
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.10, round 4:
- Fix MDIO over clocking on vf610-zii-dev-rev-b board to get switch
device work reliably.
- Fix imx50-evk IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
- Fix voltage for 1.6GHz CPU operating point on i.MX8MM to match
hardware datasheet.
- Fix phy-mode for KSZ9031 PHY on imx6qdl-udoo board.
* tag 'imx-fixes-5.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx50-evk: Fix the chip select 1 IOMUX
arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point
ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking
arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy
Link: https://lore.kernel.org/r/20201116090702.GM5849@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v5.10
- Add missing audio clock on RZ/G2H.
* tag 'renesas-fixes-for-v5.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: r8a774e1: Add missing audio_clk_b
Link: https://lore.kernel.org/r/20201113151229.3924165-1-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Mostly some fixes for a fallout in a PHY driver that pointed out errors
in our DTs. Along with that, Jernej agreed to be a reviewer!
* tag 'sunxi-fixes-for-5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: OrangePi Prime: Fix ethernet node
arm64: dts: allwinner: a64: bananapi-m64: Enable RGMII RX/TX delay on PHY
arm64: dts: allwinner: h5: libretech-all-h5-cc: Enable RGMII RX/TX delay on PHY
ARM: dts: sunxi: bananapi-m2-plus: Enable RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun9i: Enable both RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun8i: a83t: Enable both RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun8i: h3: orangepi-plus2e: Enable RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun7i: bananapi-m1-plus: Enable RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun7i: cubietruck: Enable RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun6i: a31-hummingbird: Enable RGMII RX/TX delay on Ethernet PHY
Revert "arm: sun8i: orangepi-pc-plus: Set EMAC activity LEDs to active high"
ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix ethernet node
arm64: dts: allwinner: h5: OrangePi PC2: Fix ethernet node
arm64: dts: allwinner: a64: Pine64 Plus: Fix ethernet node
arm64: dts: allwinner: a64: OrangePi Win: Fix ethernet node
arm64: dts: allwinner: Pine H64: Enable both RGMII RX/TX delay
arm64: dts: allwinner: beelink-gs1: Enable both RGMII RX/TX delay
arm64: dts: allwinner: pinetab: Drop unnecessary address/size-cells information
MAINTAINERS: Add Jernej Škrabec as a reviewer for Allwinner SoCs support
Link: https://lore.kernel.org/r/d1a1a6a6-fca4-4f1b-93b3-f2f6963b4e04.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/fixes
arm64: dts: fix for v5.10
- Fix the qspi node to have the required "jedec,spi-nor"
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.10, 3rd round:
- A series from Krzysztof Kozlowski to fix missing PMIC's interrupt
line pull-up for i.MX8MM and i.MX8MN boards.
- Set Bluetooth chip max-speed to 4000000 on imx8mm-beacon-som board
to fix the choppy Bluetooth audio sound.
- Remove non-existent OTG2, usbphynop2, and the usbmisc2 from i.MX8MN
device tree.
- Fix the endianness setting of RCPM node on Layerscape SoCs.
- Add the missing dma-coherent property for qoriq-fman device to improve
the performance.
- Fix the Ethernet PHY address on imx6q-prti6q board.
* tag 'imx-fixes-5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6q-prti6q: fix PHY address
arm64: dts imx8mn: Remove non-existent USB OTG2
arm64: dts: imx8mm-beacon-som: Fix Choppy BT audio
arm64: dts: fsl: DPAA FMan DMA operations are coherent
arm64: dts: fsl: fix endianness issue of rcpm
arm64: dts: imx8mn-evk: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mn-ddr4-evk: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mn-var-som: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mm-evk: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mm-beacon-som: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mm-var-som: fix missing PMIC's interrupt line pull-up
Link: https://lore.kernel.org/r/20201030151821.GA28266@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Since commit 71b77a7a27a3 ("enetc: Migrate to PHYLINK and PCS_LYNX") the
network port of the Kontron sl28 board is broken. After the migration to
phylink the device tree has to specify the in-band-mode property. Add
it.
Fixes: 71b77a7a27a3 ("enetc: Migrate to PHYLINK and PCS_LYNX")
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201109110436.5906-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The datasheet for both the industrial and consumer variant of the
SoC lists a typical voltage of 0.95V for the 1.6GHz CPU operating
point.
Fixes: e85c9d0faa75 (arm64: dts: imx8mm: Add cpufreq properties)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add audio_clk_b configured as 0 Hz, this will be overridden by the
boards providing the audio clock.
Fixes: 8183a7938cfec ("arm64: dts: renesas: r8a774e1: Add audio support")
Reported-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20201104105508.21197-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The QSPI flash node needs to have the required "jedec,spi-nor"
in the compatible string.
Fixes: 0cb140d07fc7 ("arm64: dts: stratix10: Add QSPI support for Stratix10")
Cc: stable@vger.kernel.org
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
According to the i.MX8MN TRM, there is only one OTG port. The
address for OTG2 is reserved on Nano.
This patch removes the non-existent OTG2, usbphynop2, and the usbmisc2
nodes.
Fixes: 6c3debcbae47 ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
When streaming bluetooth audio, the sound is choppy due to the
fact that the default baud rate of the HCI interface is too slow
to handle 16-bit stereo at 48KHz.
The Bluetooth chip is capable of up to 4M baud on the serial port,
so this patch sets the max-speed to 4000000 in order to properly
stream audio over the Bluetooth.
Fixes: 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Although the DPAA 1 FMan operations are coherent, the device tree
node for the FMan does not indicate that, resulting in a needless
loss of performance. Adding the missing dma-coherent property.
Fixes: 1ffbecdd8321 ("arm64: dts: add DPAA FMan nodes")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Tested-by: Camelia Groza <camelia.groza@oss.nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add little-endian property to RCPM node (for ls1028a,ls1088a,ls208xa),
otherwise RCPM driver will program hardware with incorrect setting,
causing system (such as LS1028ARDB) failed to be waked by wakeup source.
Fixes: 791c88ca5713 (“arm64: dts: ls1028a: Add ftm_alarm0 DT node”)
Fixes: f4fe3a8665495 (“arm64: dts: layerscape: add ftm_alarm0 node”)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PMIC's interrupt is level low and should be pulled up. The PMIC's
device node had pinctrl-0 property but it lacked pinctrl-names which
is required to apply the pin configuration.
Fixes: 4153f7811a9b ("arm64: dts: imx8mn: correct interrupt flags")
Fixes: 6386156eb279 ("arm64: dts: imx8mn-evk: add pca9450 for i.mx8mn-evk board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PMIC's interrupt is level low and should be pulled up. The PMIC's
device node had pinctrl-0 property but it lacked pinctrl-names which
is required to apply the pin configuration.
Fixes: 4153f7811a9b ("arm64: dts: imx8mn: correct interrupt flags")
Fixes: 3e44dd09736d ("arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PMIC's interrupt is level low and should be pulled up. The PMIC's
device node had pinctrl-0 property but it lacked pinctrl-names which
is required to apply the pin configuration. The actual problem in DTS
was pointed out by Felix Radensky from Variscite.
Reported-by: Felix Radensky <felix.r@variscite.com>
Fixes: ade0176dd8a0 ("arm64: dts: imx8mn-var-som: Add Variscite VAR-SOM-MX8MN System on Module")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PMIC's interrupt is level low and should be pulled up. The PMIC's
device node had pinctrl-0 property but it lacked pinctrl-names which
is required to apply the pin configuration.
Fixes: 5f67317bd967 ("arm64: dts: imx8mm: correct interrupt flags")
Fixes: aa71d0648318 ("arm64: dts: imx8mm: Split the imx8mm evk board dts to a common dtsi")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PMIC's interrupt is level low and should be pulled up. The PMIC's
device node had pinctrl-0 property but it lacked pinctrl-names which
is required to apply the pin configuration.
Fixes: 5f67317bd967 ("arm64: dts: imx8mm: correct interrupt flags")
Fixes: 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PMIC's interrupt is level low and should be pulled up. The PMIC's
device node had pinctrl-0 property but it lacked pinctrl-names which
is required to apply the pin configuration. The actual problem in DTS
was pointed out by Felix Radensky from Variscite.
Reported-by: Felix Radensky <felix.r@variscite.com>
Fixes: 5f67317bd967 ("arm64: dts: imx8mm: correct interrupt flags")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
RX and TX delay are provided by ethernet PHY. Reflect that in ethernet
node.
Fixes: 44a94c7ef989 ("arm64: dts: allwinner: H5: Restore EMAC changes")
Signed-off-by: Nenad Peric <nperic@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201028115817.68113-1-nperic@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/fixes
Amlogic fixes for v5.10-rc1
- misc DT only fixes
* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson: odroid-n2 plus: fix vddcpu_a pwm
ARM: dts: meson8: remove two invalid interrupt lines from the GPU node
arm64: dts: amlogic: add missing ethernet reset ID
arm64: dts: amlogic: meson-g12: use the G12A specific dwmac compatible
arm64: dts: meson: add missing g12 rng clock
arm64: dts: meson-axg-s400: enable USB OTG
arm64: dts: meson-axg: add USB nodes
Link: https://lore.kernel.org/r/7hlffshfu3.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The Ethernet PHY on the Bananapi M64 has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: e7295499903d ("arm64: allwinner: bananapi-m64: Enable dwmac-sun8i")
Fixes: 94f442886711 ("arm64: dts: allwinner: A64: Restore EMAC changes")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-10-wens@kernel.org
|
|
The Ethernet PHY on the Libre Computer ALL-H5-CC has the RX and TX
delays enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 60d0426d7603 ("arm64: dts: allwinner: h5: Add Libre Computer ALL-H5-CC H5 board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-9-wens@kernel.org
|
|
RX and TX delay are provided by ethernet PHY. Reflect that in ethernet
node.
Fixes: 44a94c7ef989 ("arm64: dts: allwinner: H5: Restore EMAC changes")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201023184858.3272918-1-jernej.skrabec@siol.net
|
|
According to board schematic, PHY provides both, RX and TX delays.
However, according to "fix" Realtek provided for this board, only TX
delay should be provided by PHY.
Tests show that both variants work but TX only PHY delay works
slightly better.
Update ethernet node to reflect the fact that PHY provides TX delay.
Fixes: 94f442886711 ("arm64: dts: allwinner: A64: Restore EMAC changes")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201022211301.3548422-1-jernej.skrabec@siol.net
|
|
RX/TX delay on OrangePi Win board is set on PHY. Reflect that in
ethernet node.
Fixes: 93d6a27cfcc0 ("arm64: dts: allwinner: a64: Orange Pi Win: Add Ethernet node")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201022185839.2779245-1-jernej.skrabec@siol.net
|
|
Since commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"),
the network is unusable on PineH64 model A.
This is due to phy-mode incorrectly set to rgmii instead of rgmii-id.
Fixes: 729e1ffcf47e ("arm64: allwinner: h6: add support for the Ethernet on Pine H64")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201019063449.33316-1-clabbe@baylibre.com
|
|
Before the commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the software overwrite for RX/TX delays of the RTL8211e
were not working properly and the Beelink GS1 had both RX/TX delay of RGMII
interface set using pull-up on the TXDLY and RXDLY pins.
Now that these delays are working properly they overwrite the HW
config and set this to 'rgmii' meaning no delay on both RX/TX.
This makes the ethernet of this board not working anymore.
Set the phy-mode to 'rgmii-id' meaning RGMII with RX/TX delays
in the device-tree to keep the correct configuration.
Fixes: 089bee8dd119 ("arm64: dts: allwinner: h6: Introduce Beelink GS1 board")
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201018172409.1754775-1-peron.clem@gmail.com
|
|
make dtbs_check warm about unknown address/size-cells property in the
pinetab device-tree.
This is because these information are not necessary.
Drop them.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201011211514.155266-1-peron.clem@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/fixes
mvebu fixes for 5.9 (part 1)
- Allow to use correct MAC address for particular DSA slaves /
ethernet ports on Espressobin (Armada 3720)
- Remove incorrect check in ll_get_coherency_base() used for Armada
370/XP SoCs.
* tag 'mvebu-fixes-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: mvebu: drop pointless check for coherency_base
arm64: dts: marvell: espressobin: Add ethernet switch aliases
Link: https://lore.kernel.org/r/87y2kkesj5.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Pull ARM Devicetree updates from Olof Johansson:
"As usual, most of the changes are to devicetrees.
Besides smaller fixes, some refactorings and cleanups, some of the new
platforms and chips (or significant features) supported are below:
Broadcom boards:
- Cisco Meraki MR32 (BCM53016-based)
- BCM2711 (RPi4) display pipeline support
Actions Semi boards:
- Caninos Loucos Labrador SBC (S500-based)
- RoseapplePi SBC (S500-based)
Allwinner SoCs/boards:
- A100 SoC with Perf1 board
- Mali, DMA, Cetrus and IR support for R40 SoC
Amlogic boards:
- Libretch S905x CC V2 board
- Hardkernel ODROID-N2+ board
Aspeed boards/platforms:
- Wistron Mowgli (AST2500-based, Power9 OpenPower server)
- Facebook Wedge400 (AST2500-based, ToR switch)
Hisilicon SoC:
- SD5203 SoC
Nvidia boards:
- Tegra234 VDK, for pre-silicon Orin SoC
NXP i.MX boards:
- Librem 5 phone
- i.MX8MM DDR4 EVK
- Variscite VAR-SOM-MX8MN SoM
- Symphony board
- Tolino Shine 2 HD
- TQMa6 SoM
- Y Soft IOTA Orion
Rockchip boards:
- NanoPi R2S board
- A95X-Z2 board
- more Rock-Pi4 variants
STM32 boards:
- Odyssey SOM board (STM32MP157CAC-based)
- DH DRC02 board
Toshiba SoCs/boards:
- Visconti SoC and TPMV7708 board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (638 commits)
ARM: dts: nspire: Fix SP804 users
arm64: dts: lg: Fix SP804 users
arm64: dts: lg: Fix SP805 clocks
ARM: mstar: Fix up the fallout from moving the dts/dtsi files
ARM: mstar: Add mstar prefix to all of the dtsi/dts files
ARM: mstar: Add interrupt to pm_uart
ARM: mstar: Add interrupt controller to base dtsi
ARM: dts: meson8: remove two invalid interrupt lines from the GPU node
arm64: dts: ti: k3-j7200-common-proc-board: Add USB support
arm64: dts: ti: k3-j7200-common-proc-board: Configure the SERDES lane function
arm64: dts: ti: k3-j7200-main: Add USB controller
arm64: dts: ti: k3-j7200-main.dtsi: Add USB to SERDES lane MUX
arm64: dts: ti: k3-j7200-main: Add SERDES lane control mux
dt-bindings: ti-serdes-mux: Add defines for J7200 SoC
ARM: dts: hisilicon: add SD5203 dts
ARM: dts: hisilicon: fix the system controller compatible nodes
arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
arm64: dts: zynqmp: Remove undocumented u-boot properties
arm64: dts: zynqmp: Remove additional compatible string for i2c IPs
arm64: dts: zynqmp: Rename buses to be align with simple-bus yaml
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"I had queued up a batch of fixes that got a bit close to the release
for sending in before the merge window opened, so I'm including them
in the merge window batch instead.
Mostly smaller DT tweaks and fixes, the usual mix that we tend to have
through the releases"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: iwg20d-q7-common: Fix touch controller probe failure
ARM: OMAP2+: Restore MPU power domain if cpu_cluster_pm_enter() fails
ARM: dts: am33xx: modify AM33XX_IOPAD for #pinctrl-cells = 2
soc: actions: include header to fix missing prototype
arm64: dts: ti: k3-j721e: Rename mux header and update macro names
soc: qcom: pdr: Fixup array type of get_domain_list_resp message
arm64: dts: qcom: pm660: Fix missing pound sign in interrupt-cells
arm64: dts: qcom: kitakami: Temporarily disable SDHCI1
arm64: dts: sdm630: Temporarily disable SMMUs by default
arm64: dts: sdm845: Fixup OPP table for all qup devices
arm64: dts: allwinner: h5: remove Mali GPU PMU module
ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix dcdc1 regulator
soc: xilinx: Fix error code in zynqmp_pm_probe()
|
|
On the odroid N2 plus, cpufreq is not available due to an error on the cpu
regulators. vddcpu a and b get the same PWM. The one provided to vddcpu A
is incorrect. Because vddcpu B PWM is busy the regulator cannot register:
> pwm-regulator regulator-vddcpu-b: Failed to get PWM: -16
Like on the odroid n2, use PWM A out of GPIOE_2 for vddcpu A to fix the
problem
Fixes: 98d24896ee11 ("arm64: dts: meson: add support for the ODROID-N2+")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201023094139.809379-1-jbrunet@baylibre.com
|
|
Add reset external reset of the ethernet mac controller
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201020120141.298240-1-jbrunet@baylibre.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Core changes:
- NONE whatsoever, we don't even touch the core files this time
around.
New drivers:
- New driver for the Toshiba Visconti SoC.
- New subdriver for the Qualcomm MSM8226 SoC.
- New subdriver for the Actions Semiconductor S500 SoC.
- New subdriver for the Mediatek MT8192 SoC.
- New subdriver for the Microchip SAMA7G5 SoC.
Driver enhancements:
- Intel Cherryview and Baytrail cleanups and refactorings.
- Enhanced support for the Renesas R8A7790, more pins and groups.
- Some optimizations for the MCP23S08 MCP23x17 variant.
- Some cleanups around the Actions Semiconductor subdrivers.
- A bunch of cleanups around the SH-PFC and Emma Mobile drivers.
- The "SH-PFC" (literally SuperH pin function controller, I think)
subdirectory is now renamed to the more neutral "renesas", as these
are not very much centered around SuperH anymore.
- Non-critical fixes for the Aspeed driver.
- Non-critical fixes for the Ingenic (MIPS!) driver.
- Fix a bunch of missing pins on the AMD pinctrl driver"
* tag 'pinctrl-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (78 commits)
pinctrl: amd: Add missing pins to the pin group list
dt-bindings: pinctrl: sunxi: Allow pinctrl with more interrupt banks
pinctrl: visconti: PINCTRL_TMPV7700 should depend on ARCH_VISCONTI
pinctrl: mediatek: Free eint data on failure
pinctrl: single: fix debug output when #pinctrl-cells = 2
pinctrl: single: fix pinctrl_spec.args_count bounds check
pinctrl: sunrisepoint: Modify COMMUNITY macros to be consistent
pinctrl: cannonlake: Modify COMMUNITY macros to be consistent
pinctrl: tigerlake: Fix register offsets for TGL-H variant
pinctrl: Document pinctrl-single,pins when #pinctrl-cells = 2
pinctrl: mediatek: use devm_platform_ioremap_resource_byname()
pinctrl: nuvoton: npcm7xx: Constify static ops structs
pinctrl: mediatek: mt7622: add antsel pins/groups
pinctrl: ocelot: simplify the return expression of ocelot_gpiochip_register()
pinctrl: at91-pio4: add support for sama7g5 SoC
dt-bindings: pinctrl: at91-pio4: add microchip,sama7g5
pinctrl: spear: simplify the return expression of tvc_connect()
pinctrl: spear: simplify the return expression of spear310_pinctrl_probe
pinctrl: sprd: use module_platform_driver to simplify the code
pinctrl: Ingenic: Add I2S pins support for Ingenic SoCs.
...
|
|
As part of the transition of the enetc ethernet driver from phylib
to phylink, the in-band operation mode of the SGMII interface
from enetc port 0 needs to be specified explicitly for phylink.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We have a dedicated "amlogic,meson-g12a-dwmac" compatible string for the
Ethernet controller since commit 3efdb92426bf4 ("dt-bindings: net:
dwmac-meson: Add a compatible string for G12A onwards").
Using the AXG compatible string worked fine so far because the
dwmac-meson8b driver doesn't handle the newly introduced register bits
for G12A. However, once that changes the driver must be probed with the
correct compatible string to manage these new register bits.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200925211743.537496-1-martin.blumenstingl@googlemail.com
|
|
This adds the missing perpheral clock for the RNG for Amlogic G12. As
stated in amlogic,meson-rng.yaml, this isn't always necessary for the
RNG to function, but is better to have in case the clock is disabled for
some reason prior to loading.
Signed-off-by: Scott K Logan <logans@cottsay.net>
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/520a1a8ec7a958b3d918d89563ec7e93a4100a45.camel@cottsay.net
|
|
This enables USB OTG on the S400 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This adds the USB Glue node, with the USB2 & USB3 controllers along the single
USB2 PHY node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwamatsu/linux-visconti into arm/dt
Visconti5 SoC changes for v5.10 (take two)
- Add dt-bindings for Toshiba Visconti ARM SoCs
- Add dt-bindings for the TMPV7708 RM main board
- Add initial support for Toshiba Visconti platform
- Add device tree for TMPV7708 RM main board
- Add information for Toshiba Visconti ARM SoCs to MAINTAINERS
- Enable configs for Toshiba Visconti to arm64's defconfig
* tag 'visconti-initial-for-5.10-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwamatsu/linux-visconti:
arm64: defconfig: Enable configs for Toshiba Visconti
MAINTAINERS: Add information for Toshiba Visconti ARM SoCs
arm64: dts: visconti: Add device tree for TMPV7708 RM main board
arm64: visconti: Add initial support for Toshiba Visconti platform
dt-bindings: arm: toshiba: Add the TMPV7708 RM main board
dt-bindings: arm: toshiba: add Toshiba Visconti ARM SoCs
Link: https://lore.kernel.org/r/20200923085236.4hu53gmnnmqkttuy@toshiba.co.jp
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Even though the SP804 binding allows to specify only one clock, the
primecell driver requires a named clock to activate the bus clock.
Specify the one clock three times and provide some clock-names, to
make the DT match the SP804 and primecell binding.
Also add the missing arm,primecell compatible string.
Link: https://lore.kernel.org/r/20200907121831.242281-4-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The SP805 DT binding requires two clocks to be specified, but the two
LG platform DTs currently only specify one clock.
In practice, Linux would pick a clock named "apb_pclk" for the bus
clock, and the Linux (and U-Boot) SP805 driver would use the first clock
to derive the actual watchdog counter frequency.
Since currently both are the very same clock, we can just double the
clock reference, and add the correct clock-names, to match the binding.
Link: https://lore.kernel.org/r/20200907121831.242281-6-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
arm/dt
arm64: soc: ZynqMP DT changes for v5.10
- Fix IRQ flag for PMIC
- Align gpio hogs and leds with naming convention
- Rename busses to match DT schema
- Tune i2c cadence compatible string
- Remove undocumented u-boot properties
* tag 'zynqmp-dt-for-v5.10' of https://github.com/Xilinx/linux-xlnx:
arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
arm64: dts: zynqmp: Remove undocumented u-boot properties
arm64: dts: zynqmp: Remove additional compatible string for i2c IPs
arm64: dts: zynqmp: Rename buses to be align with simple-bus yaml
arm64: dts: xilinx: align GPIO hog names with dtschema
arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
arm64: dts: xilinx: Align IOMMU nodename with dtschema
arm64: dts: zynqmp: Add GTR transceivers
Link: https://lore.kernel.org/r/37a0333b-541e-649c-68c5-aa4b52e6b91d@monstr.eu
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mani/linux-actions into arm/dt
Actions Semi ARM64 DT for v5.10:
- Fix the memory region used by pinctrl and sps drivers on the S700 SoC.
The issue is fixed by limiting the address space used by pinctrl driver.
In hardware these two are separate subsystems but the hw engineers somehow
merged the registers space into one. So we now limit the address space with
appropriate offsets for the two drivers.
- Add DMA controller support for S700 SoC. The relevant driver changes are
picked up by DMA Engine mainatainer. The DMA on this SoC can be used for
mem-to-mem and mem-to-peripheral transfers.
* tag 'actions-arm64-dt-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/linux-actions:
arm64: dts: actions: Add DMA Controller for S700
arm64: dts: actions: limit address range for pinctrl node
Link: https://lore.kernel.org/r/20200922114030.GC11251@Mani-XPS-13-9360
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Our usual bunch of patches to support the Allwinner SoCs, this time
adding:
- Allwinner A100 initial support
- Mali, DMA, cedrus and IR Support for the R40
- Crypto support for the v3s
- New board: Allwinner A100 Perf1
* tag 'sunxi-dt-for-5.10-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (24 commits)
ARM: dts: sun8i: v3s: Enable crypto engine
dt-bindings: crypto: Add compatible for V3s
dt-bindings: crypto: Specify that allwinner, sun8i-a33-crypto needs reset
arm64: dts: allwinner: a64: Update the audio codec compatible
arm64: dts: allwinner: a64: Update codec widget names
ARM: dts: sun8i: a33: Update codec widget names
ARM: dts: sun8i: r40: Add video engine node
ARM: dts: sun8i: r40: Add node for system controller
dt-bindings: sram: allwinner, sun4i-a10-system-control: Add R40 compatibles
ARM: dts: sun8i: r40: bananapi-m2-ultra: Enable IR
ARM: dts: sun8i: r40: Add IR nodes
dt-bindings: media: allwinner, sun4i-a10-ir: Add R40 compatible
ARM: dts: sun8i: r40: Add DMA node
dt-bindings: dma: allwinner,sun50i-a64-dma: Add R40 compatible
arm64: allwinner: A100: add support for Allwinner Perf1 board
dt-bindings: arm: sunxi: Add Allwinner A100 Perf1 Board bindings
arm64: allwinner: A100: add the basical Allwinner A100 DTSI file
dt-bindings: irq: sun7i-nmi: Add binding for A100's NMI controller
dt-bindings: irq: sun7i-nmi: fix dt-binding for a80 nmi
ARM: dts: sun4i: Enable HDMI support on the Mele A1000
...
Link: https://lore.kernel.org/r/ac39ee89-ea3a-4971-8cd7-8c4b2ecef39d.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux into arm/dt
Second and final device tree updates towards 5.10-rc1 for TI K3 platform.
* tag 'ti-k3-dt-for-v5.10-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux: (23 commits)
arm64: dts: ti: k3-j7200-common-proc-board: Add USB support
arm64: dts: ti: k3-j7200-common-proc-board: Configure the SERDES lane function
arm64: dts: ti: k3-j7200-main: Add USB controller
arm64: dts: ti: k3-j7200-main.dtsi: Add USB to SERDES lane MUX
arm64: dts: ti: k3-j7200-main: Add SERDES lane control mux
dt-bindings: ti-serdes-mux: Add defines for J7200 SoC
arm64: dts: ti: k3-j721e-common-proc-board: align GPIO hog names with dtschema
arm64: dts: ti: k3-j7200-common-proc-board: Add support for eMMC and SD card
arm64: dts: ti: k3-j7200-main: Add support for MMC/SD controller nodes
arm64: dts: ti: k3-j7200-som-p0: Add HyperFlash node
arm64: dts: ti: k3-j7200-mcu-wakeup: Add HyperBus node
arm64: dts: ti: k3-j7200-common-proc-board: Add I2C IO expanders
arm64: dts: ti: k3-j7200: Add I2C nodes
arm64: dts: ti: k3-j7200-common-proc-board: add mcu cpsw nuss pinmux and phy defs
arm64: dts: ti: k3-j7200-mcu: add mcu cpsw nuss node
arm64: dts: ti: k3-j7200-main: add main navss cpts node
arm64: dts: ti: k3-j7200: add DMA support
arm64: dts: ti: Add support for J7200 Common Processor Board
arm64: dts: ti: Add support for J7200 SoC
dt-bindings: arm: ti: Add bindings for J7200 SoC
...
Link: https://lore.kernel.org/r/20201002134559.orvmgbns57qlyn3i@akan
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The board uses lane 3 of SERDES for USB. Set the mux
accordingly.
The USB controller and EVM supports super-speed for USB0
on the Type-C port. However, the SERDES has a limitation
that upto 2 protocols can be used at a time. The SERDES is
wired for PCIe, QSGMII and USB super-speed. It has been
chosen to use PCI2 and QSGMII as default. So restrict
USB0 to high-speed mode.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200930122032.23481-7-rogerq@ti.com
|
