| Age | Commit message (Collapse) | Author |
|---|
|
One concept of Marvell Armada 7K/8K SoCs is that they are made of HW
blocks composed of a variety of IPs (network, PCIe, SATA, XOR, SPI,
I2C, etc.), and those HW blocks can be duplicated several times within
a given SoC. The Armada 7K SoC has a single CP110 (so no duplication),
while the Armada 8K SoC has two CP110. In the future, SoCs with more
than 2 CP110s will be introduced.
In current kernel versions, the master CP110 is described in
armada-cp110-master.dtsi and the slave CP110 is described in
armada-cp110-slave.dtsi. Those files are basically exactly the same,
since they describe the same hardware. They only have a few
differences:
- Base address of the registers is different for the "config-space"
- Base address of the PCIe registers, MEM, CONF and IO areas were
different
- Labels (and phandles pointing to them) of the nodes were different
("cpm" prefix in the master CP, "cps" prefix in the slave CP)
This duplication issue has been discussed at the DT workshop [1] in
Prague last October, and we presented on this topic [2]. The solution
of using the C pre-processor to avoid this duplication has been
validated by the people present in this DT workshop, and this patch
simply implements what has been presented.
We handle differences between the master CP and slave CP description
using the C pre-processor, by defining a set of macros with different
values armada-cp110.dtsi is included to instantiate one of the master
or slave CP110.
There are a few aspects that deserve additional explanations:
- PCIe needs to be handled separately because it is not part of the
config-space {...} node, since it has registers outside of the
range covered by config-space {...}.
- We need to defined CP110_BASE, CP110_PCIEx_BASE without 0x, because
they are used for the unit address part of some DT nodes. But since
they are also used for the "reg" property of the same nodes, we
have an ADDRESSIFY() macro that prepends 0x to those values.
We compared the resulting .dtb for armada-8040-db.dtb before and after
this patch is applied, and the result is exactly the same, except for
a few differences:
- the SDHCI controller that was only described in the master CP110 is
now also described in the slave CP110. Even though the SDHCI
controller from the slave CP110 is indeed not usable (as it isn't
wired to the outside world) it is technically part of the silicon,
and therefore it is reasonable to also describe it to be part of
the slave CP110. In addition, if we wanted to get this correct for
the SDHCI controller, we should also do it for the NAND controller,
for which the situation is even more complicated: in a single CP110
configuration (Armada 7K), the usable NAND controller is in the
master CP110, while in a dual CP110 configuration (Armada 8K), the
usable NAND controller is in the slave CP110. Since that would add
a lot of additional complexity for no good reason, and since the IP
blocks are in fact really present in both CPs, we simply describe
them in both CPs at the DT level.
- the cp110-master and cp110-slave nodes are now named cpm and
cps. We could have kept cp110-master and cp110-slave, but that
would have required adding another CP110_xyz define, which didn't
seem very useful.
Note that this commit also gets rid of the armada-cp110-master.dtsi
and armada-cp110-slave.dtsi files, as future SoCs will have more than
2 CPs. Instead, we instantiate the CPs directly from the SoC-specific
.dtsi files, i.e armada-70x0.dtsi and armada-80x0.dtsi.
[1] https://elinux.org/Device_tree_kernel_summit_2017_etherpad
[2] https://elinux.org/images/1/14/DTWorkshop2017-duplicate-data.pdf
[gregory.clement@free-electrons.com: add back the "ARM64: dts: marvell:
Fix clock resources for various node" commit]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
We are currently using the cell-index DT property to assign SPI bus
numbers. This property is specific to the spi-orion driver, and
requires each SPI controller to have a unique ID defined in the Device
Tree.
As we are about to merge armada-cp110-master.dtsi and
armada-cp110-slave.dtsi into a single file, those cell-index
properties that differ between the master CP110 and the slave CP110
are a difference that would have to be handled.
In order to avoid this, we switch to using the "aliases" DT node to
assign a unique number to each SPI controller. This is more generic,
and directly handled by the SPI core.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Back when the ICU Device Tree binding was introduced, we could not use
mvebu-icu.h from the Device Tree files, because the DT files and
mvebu-icu.h were following different merge routes towards Linus
tree. Now that both have been merged, we can switch the Marvell Armada
CP110 Device Tree files to use the mvebu-icu.h header instead of
duplicating the ICU_GRP_NSR definition.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The Armada CP110 slave NAND controller Device Tree description lists
the compatible string in the wrong order: marvell,armada-8k-nand
should come first. This commit alignes the slave CP110 description
with the master CP110 description from that respect.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Fix the same typo duplicated in both master and slave version of
armada-cp110-*.dtsi file: s/limiation/limitation/.
[gregory.clement@free-electrons.com: add the commit log]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
|
|
On the CP modules we found on Armada 7K/8K, many IP block actually also
need a "functional" clock (from the bus). This patch add them which allows
to fix some issues hanging the kernel:
If Ethernet and sdhci driver are built as modules and sdhci was loaded
first then the kernel hang.
Fixes: bb16ea1742c8 ("mmc: sdhci-xenon: Fix clock resource by adding an
optional bus clock")
Cc: stable@vger.kernel.org
Reported-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Add thermal DT nodes in AP806 and CP110 master/slave DTSI files.
Suggested-by: David Sniatkiwicz <davidsn@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Add NAND support on the Armada-8040-DB by adding the same tree as for
the Armada-7040-DB by using the same compatible string
"marvell,armada-8k-nand".
Do not enable the NAND node as enabling it (and changing manually the
proper DPR-76 switch) would disable MDIO from CP1 (and thus disable CPS
Ethernet PHY).
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional SoCs in various
areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for
networking, Amlogic A113D for audio, and Renesas R-Car V3M for
automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX,
Amlogic and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues
that the latest version of 'dtc' now warns about. Unfortunately there
is still a lot left to do.
A rework of the ARM foundation model introduced several new files for
common variations of the model"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits)
arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3
dt-bindings: bus: Add documentation for the Technologic Systems NBUS
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
...
|
|
The interrupt-map property used in the description of the Marvell
Armada 7K/8K PCIe controllers has a bogus extraneous 0 that causes the
interrupt conversion to not be done properly. This causes the PCIe PME
and AER root port service drivers to fail their initialization:
[ 5.019900] genirq: Setting trigger mode 7 for irq 114 failed (irq_chip_set_type_parent+0x0/0x30)
[ 5.028821] pcie_pme: probe of 0001:00:00.0:pcie001 failed with error -22
[ 5.035687] genirq: Setting trigger mode 7 for irq 114 failed (irq_chip_set_type_parent+0x0/0x30)
[ 5.044614] aer: probe of 0001:00:00.0:pcie002 failed with error -22
This problem was introduced when the interrupt description was
switched from using the GIC directly to using the ICU interrupt
controller. Indeed, the GIC has address-cells = <1>, which requires a
parent unit address, while the ICU has address-cells = <0>.
Fixes: 6ef84a827c37 ("arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The NAND controller used in A7K/A8K is present on the CP110 master part.
It is compatible with the pxa3xx_nand driver but requires the use of the
marvell,armada-8k-nand compatible string due to the need to first enable
the NAND controller.
Add properties to the NAND node to fit the bindings constraints of the
pxa3xx_nand driver and enable the NAND controller.
Add the 'marvell,system-controller' property to the cp110 master NAND
node with a reference to the syscon node. This is new compared to other
boards using the pxa3xx_nand driver and it is needed to be bootloader
independent and enable the NAND controller from the NAND controller
driver itself by writing in these syscon registers.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
[miquel.raynal@free-electrons.com: add NAND ready/busy MPP subnode,
change compatible string to fit the needs of the A7k/A8k SoCs and add
the system controller property]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
|
|
Ports interrupts are used by the PPv2 driver when no PHY is connected to
a port. This patch adds a description of these interrupts.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This patch describes the comphy available in the cp110 master and slave.
This comphy provides serdes lanes used by various controllers such as
the network one.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This patch extends on both cp110 the system register area length to
include some of the comphy registers as well.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The network driver on Marvell SoC (7k/8k) needs to access some registers
in the system controller to configure its ports at runtime. This patch
adds a phandle reference to the syscon system controller node in the
ppv2 node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This commit updates the Marvell Armada 7K/8K Device Tree to describe
the TX interrupts of the Ethernet controllers, in both the master and
slave CP110s.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The NAND controller used in A7K/A8K is present on the CP110. It is
compatible with the pxa-nand driver.
However, due to the limiation of the pins available this controller is
only usable on the CPM for A7K and on the CPS for A8K.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Since the introduction of the CP110 dt files, the sata node was
misplaced. Move it at the right place. Thanks to this, the files are
completely ordered.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
In both the CP110 master and slave description, the node describing
the RTC was at the wrong place when taking into account increasing
register addresses. Interestingly, it was not even at the same (wrong)
place in both files.
This commit adjusts that, making the master and slave descriptions
more aligned.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Add the GPIO interrupts for the CP110.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The crypto engines found on the cp110 master and slave are dma coherent.
This patch adds the relevant property to their dt nodes.
Cc: stable@vger.kernel.org # v4.12+
Fixes: 973020fd9498 ("arm64: marvell: dts: add crypto engine description for 7k/8k")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
When the conversion of the Marvell CP110 Device Tree description from
using GIC interrupts to using ICU interrupts was done, the RTC on the
slave CP110 was left unchanged. This commit fixes that, so that all
devices on the CP properly get their interrupt through the ICU.
Fixes: 6ef84a827c375 ("arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
As I found by chance while merging another patch, the usage of
a dma-mask in this DT node is wrong for multiple reasons:
- dma-masks are a Linux specific concept, not a general
hardware feature
- In DT, we use the "dma-ranges" property to describe how DMA
addresses related between devices.
- The 40-bit mask appears to be completely unnecessary here, as
the SoC cannot address that much memory anyway, so simply
asking for a 64-bit mask (as supported by the device) should
succeed anyway.
The patch to remove the parsing of the property is getting merged
through the crypto tree.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
next/dt64
mvebu fixes for 4.12
Fix the interrupt description of the crypto node for device tree of
the Armada 7K/8K SoCs
* tag 'mvebu-fixes-4.12-1' of git://git.infradead.org/linux-mvebu:
arm64: marvell: dts: fix interrupts in 7k/8k crypto nodes
|
|
This commit modifies the Marvell EBU Armada 7K and 8K Device Tree files
to describe the ICU and GICP units, and use ICU interrupts for all
devices in the CP110 blocks.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Enable gpio support for CP and AP on the Marvell Armada 7K/8K SoCs.
The Armada 8K has two CP110 blocks, each having two GPIO controllers.
However, in each CP110 block, one of the GPIO controller cannot be
used: in the master CP110, only the second GPIO controller can be used,
while on the slave CP110, only the first GPIO controller can be used.
On the other side, the Armada 7K has only one CP110, but both its GPIO
controllers can be used.
For this reason, the GPIO controllers are marked as "disabled" in the
armada-cp110-master.dtsi and armada-cp110-slave.dtsi files, and only
enabled in the per-SoC dtsi files.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The new binding for the system controller on cp110 moved the clock
controller into a subnode. This preliminary step will allow to add gpio
and pinctrl subnodes.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The *-clock-output-names of the cp110-system-controller0 node are not
used anymore, so remove them.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Add the description of the xMDIO bus for the Marvell Armada 7k and
Marvell Armada 8k; for both CP110 slave and master. This bus is found
on Marvell Ethernet controllers and provides an interface with the
xMDIO bus.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The cryptographic engine found on the cp110 slave is disabled by default
because of some known limitations. Add a comment to explain why it is
disabled by default.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Disable the mdio nodes by default in the cp110 slave and master dtsi as
they're not wired on every board.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The EIP197 cryptographic engine supports 64 bits address width but is
limited to 40 bits on 7k/8k. Add a dma-mask property in the
cryptographic engine nodes to reflect this.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Add the three required clocks for the MDIO interface to be functional
on Armada 8k platforms. Without this, the CPU hangs, causing RCU
stalls or the system to become unresponsive.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[Thomas:
- remove mg_core_clock, since it's a parent of mg_clock
- also add clock references to the slave CP mdio instance]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The cryptographic engine nodes have an interrupt which is configured as
both edge and level, which makes no sense at all. Fix this by
configuring it the right way (level).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Add the description of the crypto engine hardware block for the Marvell
Armada 7k and Armada 8k processors; for both the CP110 slave and master.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This commit adds the description of the PPv2.2 hardware block for the
Marvell Armada 7K and Armada 8K processors, and their corresponding Armada
7040 and 8040 Development boards.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This RTC IP is found in the CP110 master and slave which are part of the
Armada 8K SoCs and of the subset family the Armada 7K.
There is one RTC in each CP but the RTC requires an external
oscillator. However on the Armada 80x0, the RTC clock in CP master is not
connected (by package) to the oscillator. So this one is disabled for the
Armada 8020 and the Armada 8040.
As the RTC clock in CP slave is connected to the oscillator this one is
let enabled. and will be used on these SoCs (80x0).
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This commit adjusts the names of gatable clock #18 of the Marvell Armada
CP110 system controller. This clock not only controls SD/MMC, but also
the GOP (Group Of Ports) used for networking. So the clock is renamed to
{cpm,cps}-sd-mmc-gop instead of {cpm,cps}-sd-mmc.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Testing with an Armada 8040 board shows that adding the generic-ahci
compatible to the CP110 AHCI nodes gets us working AHCI on the board.
A previous patch series posted by Thomas Petazzoni was retracted when
it was realised that the IP was supposed to be, and is, compatible
with the standard register layout.
Add this compatible.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost)
fully supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier
LS1043A with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above chips,
there are only a few consumer devices and boards added this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral
support for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom,
Rockchip, Berlin, and ZTE"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (168 commits)
arm64: dts: fix build errors from missing dependencies
ARM64: dts: meson-gxbb: add SCPI pre-1.0 compatible
ARM64: dts: meson-gxl: Add support for Nexbox A95X
ARM64: dts: meson-gxm: Add support for the Nexbox A1
ARM: dts: artpec: add pcie support
arm64: dts: berlin4ct-dmp: add missing unit name to /memory node
arm64: dts: berlin4ct-stb: add missing unit name to /memory node
arm64: dts: berlin4ct: add missing unit name to /soc node
arm64: dts: qcom: msm8916: Add ddr support to sdhc1
arm64: dts: exynos: Enable HS400 mode for eMMC for TM2
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM64: dts: Add support for Meson GXM
dt-bindings: add rockchip RK1108 Evaluation board
arm64: dts: NS2: Add PCI PHYs
arm64: dts: NS2: enable sdio1
arm64: dts: exynos: Add the mshc_2 node for supporting T-Flash
arm64: tegra: Add NVIDIA P2771 board support
arm64: tegra: Enable PSCI on P3310
arm64: tegra: Add NVIDIA P3310 processor module support
arm64: tegra: Add GPIO controllers on Tegra186
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.10:
API:
- add skcipher walk interface
- add asynchronous compression (acomp) interface
- fix algif_aed AIO handling of zero buffer
Algorithms:
- fix unaligned access in poly1305
- fix DRBG output to large buffers
Drivers:
- add support for iMX6UL to caam
- fix givenc descriptors (used by IPsec) in caam
- accelerated SHA256/SHA512 for ARM64 from OpenSSL
- add SSE CRCT10DIF and CRC32 to ARM/ARM64
- add AEAD support to Chelsio chcr
- add Armada 8K support to omap-rng"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (148 commits)
crypto: testmgr - fix overlap in chunked tests again
crypto: arm/crc32 - accelerated support based on x86 SSE implementation
crypto: arm64/crc32 - accelerated support based on x86 SSE implementation
crypto: arm/crct10dif - port x86 SSE implementation to ARM
crypto: arm64/crct10dif - port x86 SSE implementation to arm64
crypto: testmgr - add/enhance test cases for CRC-T10DIF
crypto: testmgr - avoid overlap in chunked tests
crypto: chcr - checking for IS_ERR() instead of NULL
crypto: caam - check caam_emi_slow instead of re-lookup platform
crypto: algif_aead - fix AIO handling of zero buffer
crypto: aes-ce - Make aes_simd_algs static
crypto: algif_skcipher - set error code when kcalloc fails
crypto: caam - make aamalg_desc a proper module
crypto: caam - pass key buffers with typesafe pointers
crypto: arm64/aes-ce-ccm - Fix AEAD decryption length
MAINTAINERS: add crypto headers to crypto entry
crypt: doc - remove misleading mention of async API
crypto: doc - fix header file name
crypto: api - fix comment typo
crypto: skcipher - Add separate walker for AEAD decryption
..
|
|
config-space has a ranges property so the unit name should contain an
address.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Enabling SPI controllers, which are attached to different busses
inside an SoC, may result in overlapping enumeration and cause
sysfs registration failure. Example log after enabling two
controllers on Armada 8040 SoC with same identifiers:
[ 3.740415] sysfs: cannot create duplicate filename
'/class/spi_master/spi0'
[ 3.747510] ------------[ cut here ]------------
[ 3.752145] WARNING: at fs/sysfs/dir.c:31
[...]
[ 4.002299] orion_spi: probe of f4700600.spi failed with error -17
spi-orion driver offers dedicated DT property ('cell-index'), that
allow setting unique identifiers. Recently added support for CP110-slave
HW block introduced two new SPI controllers' nodes with same ID as
ones from CP110-master.
This commit fixes the issue by assigning different 'cell-index' values
for CP110-slave SPI controllers.
Fixes: 4eef78a0091b ("arm64: dts: marvell: add description for the slave
CP110 in Armada 8K")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
I2C and SPI interfaces share common clock trees within the CP110 HW block.
It occurred that SPI0 interface has wrong clock assignment in the device
tree, which is fixed in this commit to a proper value.
Fixes: c749b8d9de32 ("arm64: dts: marvell: add description for the ...")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This commits adds the devicetree description of the SafeXcel IP-76 TRNG
found in the two Armada CP110.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This commit adds a reference to the appropriate MSI controller in the
description of the PCIe controllers on Marvel Armada 7K and 8K
platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The Armada 8K platforms (8020 and 8040) have two CP110 HW blocks: one
master, one slave. So far, only the master CP110 was described. This
commit adds the Device Tree description for the slave CP110, and hooks
it up in the DT description of the Armada 8020 and Armada 8040 SoCs.
The slave CP110 description is somewhat similar to the master CP110
description except for a number of things like register offsets,
interrupt numbers, references to clocks, etc.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
