| Age | Commit message (Collapse) | Author |
|---|
|
Add TPM device found on Verdin iMX8M Mini PID4 0090 variant.
While adding the node, rename `pinctrl_pmic_tpm_ena` to
`pinctrl_tpm_spi_cs`.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX fixes for 6.10:
- Fix GPIO number for reg_usdhc2_vmmc on imx8qm-mek board.
- Enable hysteresis for SODIMM_17 pin on imx8mm-verdin board to increase
immunity against noise.
- Remove 'no-sdio' property for uSDHC2 on imx93-11x11-evk board, so that
SDIO cards could also work.
- Fix BT shutdown GPIO for imx8mp-venice-gw73xx-2x board.
- Fix panel node deleting on imx53-qsb-hdmi, as /delete-node/ directive
doesn't really delete a node in a DT overlay.
- Fix TC9595 input clock on DH i.MX8M Plus DHCOM SoM.
- Fix GPU speed for imx8mm-verdin board by enabling overdrive mode in
the SOM dtsi.
|
|
SODIMM 17 can be used as an edge triggered interrupt supplied from an
off board source.
Enable hysteresis on the pinmuxing to increase immunity against noise
on the signal.
Fixes: 60f01b5b5c7d ("arm64: dts: imx8mm-verdin: update iomux configuration")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Verdin I2C2 may be used to access other I2C devices apart from serving
as an HDMI DDC channel.
Thus do not limit the used I2C clock frequency to 10kHz in the module
specific device tree part.
If an overlay configures i2c2 as DDC the overlay is also responsible
to cope with an appropriate I2C clock.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GPU clock was reduced on iMX8MM SOC device tree to prevent boards
that don't support GPU overdrive from being out of specification. However,
this caused a regression in GPU speed for the Verdin iMX8MM, which does
support GPU overdrive. This patch fixes this by enabling overdrive mode
in the SOM dtsi.
Fixes: 1f794d3eed53 ("arm64: dts: imx8mm: Reduce GPU to nominal speed")
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Verdin family has a signal called sleep-moci which can be used to
turn off peripherals on the carrier board when the SoM goes into
suspend. So far we have hogged this signal, which means the peripherals
are always on and it is not possible to add peripherals that depend on
the sleep-moci to be on. With this change, we replace the hog with a
regulator so that peripherals can add their own regulators that use the
same gpio. Carrier boards that allow peripherals to be powered off in
suspend can disable this regulator and implement their own regulator to
control the sleep-moci.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The property should be off-on-delay-us, not off-on-delay
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull SoC DT updates from Arnd Bergmann:
"About a quarter of the changes are for 32-bit arm, mostly filling in
device support for existing machines and adding minor cleanups, mostly
for Qualcomm and Samsung based machines.
Two new 32-bit SoCs are added, both are quad-core Cortex-A7 chips from
Rockchips that have been around for a while but were lacking kernel
support so far: RV1126 is a Vision SoC with an NPU and is used in the
Edgeble Neural Compute Module 2(Neu2) board, while RK3128 is design
for TV boxes and so far only comes with a dts for its refernece
design.
The other 32-bit boards that were added are two ASpeed AST2600 based
BMC boards, the Microchip sam9x60_curiosity development board (Armv5
based!), the Enclustra PE1 FPGA-SoM baseboard, and a few more boards
for i.MX53 and i.MX6ULL.
On the RISC-V side, there are fewer patches, but a total of ten new
single-board computers based on variations of the Allwinner D1/T113
chip, plus one more board based on Microchip Polarfire.
As usual, arm64 has by far the most changes here, with over 700
non-merge changesets, among them over 400 alone for Qualcomm. The
newly added SoCs this time are all recent high-end embedded SoCs for
various markets, each on comes with support for its reference board:
- Qualcomm SM8550 (Snapdragon 8 Gen 2) for mobile phones
- Qualcomm QDU1000/QRU1000 5G RAN platform
- Rockchips RK3588/RK3588s for tablets, chromebooks and SBCs
- TI J784S4 for industrial and automotive applications
In total, there are 46 new arm64 machines:
- Reference platforms for each of the five new SoCs
- Three Amlogic based development boards
- Six embedded machines based on NXP i.MX8MM and i.MX8MP
- The Mediatek mt7986a based Banana Pi R3 router
- Six tablets based on Qualcomm MSM8916 (Snapdragon 410), SM6115
(Snapdragon 662) and SM8250 (Snapdragon 865)
- Two LTE dongles, also based on MSM8916
- Seven mobile phones, based on Qualcomm MSM8953 (Snapdragon 610),
SDM450 and SDM632
- Three chromebooks based on Qualcomm SC7280 (Snapdragon 7c)
- Nine development boards based on Rockchips RK3588, RK3568, RK3566
and RK3328.
- Five development machines based on TI K3 (AM642/AM654/AM68/AM69)
The cleanup of dtc warnings continues across all platforms, adding to
the total number of changes"
* tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (1035 commits)
dt-bindings: riscv: correct starfive visionfive 2 compatibles
ARM: dts: socfpga: Add enclustra PE1 devicetree
dt-bindings: altera: Add enclustra mercury PE1
arm64: dts: qcom: msm8996: align RPM G-Link clock-controller node with bindings
arm64: dts: qcom: qcs404: align RPM G-Link node with bindings
arm64: dts: qcom: ipq6018: align RPM G-Link node with bindings
arm64: dts: qcom: sm8550: remove invalid interconnect property from cryptobam
arm64: dts: qcom: sc7280: Adjust zombie PWM frequency
arm64: dts: qcom: sc8280xp-pmics: Specify interrupt parent explicitly
arm64: dts: qcom: sm7225-fairphone-fp4: enable remaining i2c busses
arm64: dts: qcom: sm7225-fairphone-fp4: move status property down
arm64: dts: qcom: pmk8350: Use the correct PON compatible
arm64: dts: qcom: sc8280xp-x13s: Enable external display
arm64: dts: qcom: sc8280xp-crd: Introduce pmic_glink
arm64: dts: qcom: sc8280xp: Add USB-C-related DP blocks
arm64: dts: qcom: sm8350-hdk: enable GPU
arm64: dts: qcom: sm8350: add GPU, GMU, GPU CC and SMMU nodes
arm64: dts: qcom: sm8350: finish reordering nodes
arm64: dts: qcom: sm8350: move more nodes to correct place
arm64: dts: qcom: sm8350: reorder device nodes
...
|
|
The VSELECT pin is configured as MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT
and not as a GPIO, drop the bogus sd-vsel-gpios property as the eSDHC
block handles the VSELECT pin on its own.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move the PCIe clock-names property from various DTs into SoC dtsi to
reduce duplication. In case of a couple of boards, reorder the clock
so they match the order in yaml DT bindings.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx8mm.dtsi, imx8mm-tqma8mqml-mba8mx.dts
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Currently if suspending using either freeze or memory state, the fec
driver tries to power down the phy which leads to crash of the kernel
and non-responsible kernel with the following call trace:
[ 24.839889 ] Call trace:
[ 24.839892 ] phy_error+0x18/0x60
[ 24.839898 ] kszphy_handle_interrupt+0x6c/0x80
[ 24.839903 ] phy_interrupt+0x20/0x2c
[ 24.839909 ] irq_thread_fn+0x30/0xa0
[ 24.839919 ] irq_thread+0x178/0x2c0
[ 24.839925 ] kthread+0x154/0x160
[ 24.839932 ] ret_from_fork+0x10/0x20
Since there is currently no functionality in the phy subsystem to power
down phys let's just disable the feature of powering-down the ethernet
phy.
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add hot plug detect gpio to the HDMI connector.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Disable usb over-current of the chipidea driver on all Carrier-Boards
used by Toradex. Do this as we don't want to use this functionality on
our Carrier Boards and to leave it open to someone who includes our
module-level device-trees.
Remove the now obsolete disable-over-current flag from module-level
device-tree imx8mm-verdin.dtsi and leave it as already mentioned to
the people actually implementing the carrier-board to implement this.
This will prevent the warning "No over current polarity defined" from
being printed on boot.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix the following dtbs_check warning on all of i.MX8M variants:
"
opp-table: Unevaluated properties are not allowed ('opp-25M', 'opp-100M', 'opp-750M' were unexpected)
"
Using the following command:
"
$ sed -i '/opp-[0-9]\+M/ s@M {@000000 {@' arch/arm64/boot/dts/freescale/imx8m*
"
The Documentation/devicetree/bindings/opp/opp-v2-base.yaml expects the OPP
subnode names to be full frequency listings in Hz without unit suffixes.
Only the i.MX8M DTs are affected per "git grep 'opp-[0-9]\+M'", so fix them.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Slight improvement of pcie node to be more in-line with what we add on
the Verdin iMX8M Plus.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Rename sn65dsi83 to sn65dsi84 as that is the exact chip used on the
Verdin DSI to LVDS Adapter.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Improve include notation. Usually only dtsi files from the same location
are included with an absolute path in quotes. Others should use a
relative path enclosed in angle brackets.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the changes fall into one of three categories: adding support
for additional devices on existing machines, cleaning up issues found
by the ongoing conversion to machine-readable bindings, and addressing
minor mistakes in the existing DT data.
Across SoC vendors, Qualcomm and Freescale stick out as getting the
most updates, which corresponds to their dominance in the mobile phone
and embedded industrial markets, respectively.
There are 636 non-merge changeset in this branch, which is a little
lower than most times, but more importantly we only add 36 machine
files, which is about half of what we had the past few releases.
Eight new SoCs are added, but all of them are variations of already
supported SoC families, and most of them come with one reference board
design from the SoC vendor:
- Mediatek MT8186 is a Chromebook/Tablet type SoC, similar to the
MT65xx series of phone SoCs, with two Cortex-A76 and six Cortex-A55
cores.
- TI AM62A is another member of the K3 family with Cortex-A53 cores,
this one is targetted at Video/Vision processing for industrial and
automotive applications.
- NXP i.MX8DXL is another chip for this market in the ever-growing
i.MX8 family, this one again with two Cortex-A35 cores.
- Renesas R-Car H3Ne-1.7G (R8A779MB) and R-Car V3H2 (R8A77980A) are
minor updates of R8A77951 and R8A77980, respectively.
- Qualcomm IPQ8064-v2.0, IPQ8062 and IPQ8065 are all variants of the
IPQ8064 chip, with minimally different features.
The AMD Pensando Elba and Apple M1 Ultra SoC support was getting close
this time, but in the end did not make the cut.
The new machines based on existing SoC support are fairly uneventful:
- Sony Xperia 1 IV is a fairly recent phone based on Qualcomm
Snapdragon 8 Gen 1.
- Three Samsung phones based on Snapdragon 410: Galaxy E5, E7 and
Grand Max. These are added for both 32-bit and 64-bit kernels, as
they originally shipped running 32-bit code.
- Two new servers using AST2600 BMCs: AMD DaytonaX and Ampere Mt.
Mitchell
- Three new machines based on Rockchips RK3399 and RK3566: Anberic
RG353P and RG503, Pine64 Pinephone Pro, Open AI Lab
- Multiple NXP i.MX6/i.MX8 based boards: Kontron SL/BL i.MX8MM OSM-S,
i.MX8MM Gateworks GW7904, MSC SM2S-IMX8PLUS SoM and carrier board
- Two development boards in the Microchip AT91 family: SAMA5D3-EDS
and lan966x-pcb8290.
- Minor variants of existing boards using Amlogic, Broadcom, Marvell,
Rockchips, Freescale Layerscape and Socionext Uniphier SoCs"
* tag 'arm-dt-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (617 commits)
Revert "ARM: dts: BCM5301X: Add basic PCI controller properties"
ARM: dts: s5pv210: correct double "pins" in pinmux node
ARM: dts: exynos: fix polarity of VBUS GPIO of Origen
arm64: dts: exynos: fix polarity of "enable" line of NFC chip in TM2
arm64: dts: uniphier: Add L2 cache node
arm64: dts: uniphier: Remove compatible "snps,dw-pcie" from pcie node
arm64: dts: uniphier: Fix opp-table node name for LD20
arm64: dts: uniphier: Add USB-device support for PXs3 reference board
arm64: dts: uniphier: Add ahci controller nodes for PXs3
arm64: dts: uniphier: Use GIC interrupt definitions
arm64: dts: uniphier: Rename gpio-hog nodes
arm64: dts: uniphier: Rename usb-glue node for USB3 to usb-controller
arm64: dts: uniphier: Rename usb-phy node for USB2 to usb-controller
arm64: dts: uniphier: Rename pvtctl node to thermal-sensor
ARM: dts: uniphier: Remove compatible "snps,dw-pcie-ep" from pcie-ep node
ARM: dts: uniphier: Move interrupt-parent property to each child node in uniphier-support-card
ARM: dts: uniphier: Add ahci controller nodes for PXs2
ARM: dts: uniphier: Add ahci controller nodes for Pro4
ARM: dts: uniphier: Use GIC interrupt definitions
ARM: dts: uniphier: Rename gpio-hog node
...
|
|
The Lontium LT8912B driver needs a HDMI connector to be connected to
port 1. Introduce this connector to be enabled in a device tree overlay.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add an LVDS panel node to be extended by a device tree overlay.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Rename sn65dsi83 to sn65dsi84 as that is the exact chip used on the
Verdin DSI to LVDS Adapter.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Currently, we limited the voltages from the PMIC very strictly. This
causes an issue with one Toradex SKU that uses a consumer-grade chip
that is capable of going up to 1.8GHz at 1.00V.
Extend the ranges to min/max values of the SoC operating ranges (table
10) in the datasheet. Detailed explanation as follows:
BUCK2:
- As already described above, the SKU with the consumer-grade chip
needs a voltage of at least 1.00V. 1.05V is chosen now as this is
listed as the maximum. Both industrial and consumer-grade chips have
an absolute maximum rating of 1.15V which makes it still safe to put
1.05V
- Lower the regulator-min value to the smallest value allowed from the
Quad-A53, 1.2GHz version of the SoC
BUCK3:
- This regulator is used for SoC input voltages VDD_GPU, VDD_VPU and
VDD_DRAM.
- Use the smallest value of these three inputs as the regulator-min
- Use the largest value of these three inputs as the regulator-max
LDO2:
- This LDO is used for VDD_SNVS_0P8 SoC input voltage. As this has a
single nominal input voltage just put this in the middle of 0.8V.
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix reset GPIO polarity in-line with the following commit feedaacdadfc
("Input: atmel_mxt_ts - fix up inverted RESET handler").
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Verdin iMX8M Mini System on Module does not have USB-ID signal
connected on Verdin USB_2 (usbotg2). On Verdin Development board this is
no problem, as we have connected a USB-Hub that is always connected.
However, if Verdin USB_2 is desired to be used as a single USB-Host port
the chipidea driver does not detect if a USB device is plugged into this
port, due to runtime pm shutting down the PHY.
Add the power-domain &pgc_otg2 to &usbphynop2 in order to detect
plugging events and enumerate the usb device.
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Switch to level interrupt for mcp251xfd. This will make sure no
interrupts are lost.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Update SPI CAN controller clock to match current hardware design.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use IT temperature threshold for critical/passive trip point
on Verdin iMX8M Plus and Mini.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add SD1 sleep pinctrl to avoid backfeeding during sleep.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a note about us using discrete external on-module resistors
pulling-up to the on-module +V3.3_1.8_SD (LDO5) rail and explicitly
disabling the internal pull-ups due to ERR050080 [1]:
IO: Degradation of internal IO pullup/pulldown current capability for
IO’s continuously driven in a 3.3V operating mode
[1] https://www.nxp.com/webapp/Download?colCode=IMX8MM_0N87W
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix capitalisation of Verdin in comments.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Alphabetically re-order pinctrl groups.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Update IOMUX configuration as required by the hardware design team.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a note about the bootloader being expected to switch on the I2C
level shifter for the TLA2024 ADC behind this PMIC.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Make sure we only have dashes rather than underscores in node names by
renaming ctrl_sleep_moci-hog to ctrl-sleep-moci-hog.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix multi-line comment style.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Annotate regulators which are on-module.
Rename usb_otg{1/2}_vbus to USB_{1/2}_EN more in-line with Verdin spec.
Annotate PMIC regulators with information on which BUCK/LDO they are on.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds the device tree to support Toradex Verdin iMX8M Mini a
computer on module which can be used on different carrier boards.
The module consists of an NXP i.MX 8M Mini family SoC (either i.MX 8M
Mini Quad or 8M Mini DualLite), a PCA9450A PMIC, a Gigabit Ethernet PHY,
1 or 2 GB of LPDDR4 RAM, an eMMC, a TLA2024 ADC, an I2C EEPROM, an
RX8130 RTC, an optional SPI CAN controller plus an optional Bluetooth/
Wi-Fi module.
Anything that is not self-contained on the module is disabled by
default.
The device tree for the Dahlia includes the module's device tree and
enables the supported peripherals of the carrier board.
The device tree for the Verdin Development Board includes the module's
device tree as well as the Dahlia one as it is a superset and supports
almost all peripherals available.
So far there is no display functionality supported at all but basic
console UART, PCIe, USB host, eMMC and Ethernet and PCIe functionality
work fine.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
