| Age | Commit message (Collapse) | Author |
|---|
|
mvebu fixes for 5.0
They are all device tree fixes which also worth being in stable:
- Reserve PSCI area on Armada 7K/8K preventing the kernel accessing
this area and crashing while doing it.
- Use correct PCIe reset signal on MACCHIATOBin (Armada 8040 based)
- Fix polarity of GPIO fan line D-Link DNS NASes(kikwood based)
* tag 'mvebu-fixes-5.0-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: Fix polarity of GPIO fan lines
arm64: dts: marvell: mcbin: fix PCIe reset signal
arm64: dts: marvell: armada-ap806: reserve PSCI area
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
These two lines are active high, not active low. The bug was
found when we changed the kernel to respect the polarity defined
in the device tree.
Fixes: 1b90e06b1429 ("ARM: kirkwood: Use devicetree to define DNS-32[05] fan")
Cc: Jamie Lentin <jm@lentin.co.uk>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Julien D'Ascenzio <jdascenzio@posteo.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Reported-by: Julien D'Ascenzio <jdascenzio@posteo.net>
Tested-by: Julien D'Ascenzio <jdascenzio@posteo.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
To avoid the following error:
asoc-simple-card sound: ASoC: Failed to create card debugfs directory
Which is because the card name contains '/' character, which can not be
used in file or directory names.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add the board level fixed regulators for 3.3V and 1.8V which is used to
power - among other things - the tlv320aic3106 codec.
Apart from removing the following warning during boot:
tlv320aic3x-codec 0-0018: Invalid supply voltage(s) AVDD: -22, DVDD: -22
With the correct voltages the driver can select correct OCMV value to
reduce pop noise.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
To avoid the following error:
asoc-simple-card sound: ASoC: Failed to create card debugfs directory
Which is because the card name contains '/' character, which can not be
used in file or directory names.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add the board level fixed regulators for 3.3V and 1.8V which is used to
power - among other things - the tlv320aic3106 codec.
Apart from removing the following warning during boot:
tlv320aic3x-codec 0-0018: Too high supply voltage(s) AVDD: 5000000, DVDD: 5000000
With the correct voltages the driver can select correct OCMV value to
reduce pop noise.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Remove unused lists from ASPM pcie_link_state (Frederick Lawler)
- Fix Broadcom CNB20LE host bridge unintended sign extension (Colin Ian
King)
- Expand Kconfig "PF" acronyms (Randy Dunlap)
- Update MAINTAINERS for arch/x86/kernel/early-quirks.c (Bjorn Helgaas)
- Add missing include to drivers/pci.h (Alexandru Gagniuc)
- Override Synopsys USB 3.x HAPS device class so dwc3-haps can claim it
instead of xhci (Thinh Nguyen)
- Clean up P2PDMA documentation (Randy Dunlap)
- Allow runtime PM even if driver doesn't supply callbacks (Jarkko
Nikula)
- Remove status check after submitting Switchtec MRPC Firmware Download
commands to avoid Completion Timeouts (Kelvin Cao)
- Set Switchtec coherent DMA mask to allow 64-bit DMA (Boris Glimcher)
- Fix Switchtec SWITCHTEC_IOCTL_EVENT_IDX_ALL flag overwrite issue
(Joey Zhang)
- Enable write combining for Switchtec MRPC Input buffers (Kelvin Cao)
- Add Switchtec MRPC DMA mode support (Wesley Sheng)
- Skip VF scanning on powerpc, which does this in firmware (Sebastian
Ott)
- Add Amlogic Meson PCIe controller driver and DT bindings (Yue Wang)
- Constify histb dw_pcie_host_ops structure (Julia Lawall)
- Support multiple power domains for imx6 (Leonard Crestez)
- Constify layerscape driver data (Stefan Agner)
- Update imx6 Kconfig to allow imx6 PCIe in imx7 kernel (Trent Piepho)
- Support armada8k GPIO reset (Baruch Siach)
- Support suspend/resume support on imx6 (Leonard Crestez)
- Don't hard-code DesignWare DBI/ATU offst (Stephen Warren)
- Skip i.MX6 PHY setup on i.MX7D (Andrey Smirnov)
- Remove Jianguo Sun from HiSilicon STB maintainers (Lorenzo Pieralisi)
- Mask DesignWare interrupts instead of disabling them to avoid lost
interrupts (Marc Zyngier)
- Add locking when acking DesignWare interrupts (Marc Zyngier)
- Ack DesignWare interrupts in the proper callbacks (Marc Zyngier)
- Use devm resource parser in mediatek (Honghui Zhang)
- Remove unused mediatek "num-lanes" DT property (Honghui Zhang)
- Add UniPhier PCIe controller driver and DT bindings (Kunihiko
Hayashi)
- Enable MSI for imx6 downstream components (Richard Zhu)
* tag 'pci-v4.21-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (40 commits)
PCI: imx: Enable MSI from downstream components
s390/pci: skip VF scanning
PCI/IOV: Add flag so platforms can skip VF scanning
PCI/IOV: Factor out sriov_add_vfs()
PCI: uniphier: Add UniPhier PCIe host controller support
dt-bindings: PCI: Add UniPhier PCIe host controller description
PCI: amlogic: Add the Amlogic Meson PCIe controller driver
dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe controller
arm64: dts: mt7622: Remove un-used property for PCIe
arm: dts: mt7623: Remove un-used property for PCIe
dt-bindings: PCI: MediaTek: Remove un-used property
PCI: mediatek: Remove un-used variant in struct mtk_pcie_port
MAINTAINERS: Remove Jianguo Sun from HiSilicon STB DWC entry
PCI: dwc: Don't hard-code DBI/ATU offset
PCI: imx: Add imx6sx suspend/resume support
PCI: armada8k: Add support for gpio controlled reset signal
PCI: dwc: Adjust Kconfig to allow IMX6 PCIe host on IMX7
PCI: dwc: layerscape: Constify driver data
PCI: imx: Add multi-pd support
PCI: Override Synopsys USB 3.x HAPS device class
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull more ARM SoC updates from Olof Johansson:
"A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a
build fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated
Vivante GPU, 256MB RAM, Wifi). This includes some acked
platform-specific drivers (serial, etc). This also include DTs for
two boards with this SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: multi_v7_defconfig: enable CONFIG_UNIPHIER_MDMAC
arm64: defconfig: Re-enable bcm2835-thermal driver
MAINTAINERS: Add entry for RDA Micro SoC architecture
tty: serial: Add RDA8810PL UART driver
ARM: dts: rda8810pl: Add interrupt support for UART
dt-bindings: serial: Document RDA Micro UART
ARM: dts: rda8810pl: Add timer support
ARM: dts: Add devicetree for OrangePi i96 board
ARM: dts: Add devicetree for OrangePi 2G IoT board
ARM: dts: Add devicetree for RDA8810PL SoC
ARM: Prepare RDA8810PL SoC
dt-bindings: arm: Document RDA8810PL and reference boards
dt-bindings: Add RDA Micro vendor prefix
ARM: sti: remove pen_release and boot_lock
arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a
fragment, that later gets filled in on later releases, and in some
cases it's near-complete platform support. The latter is more common
for derivative platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions.
Allwinner support for F1C100s, a quite old SoC (ARMv5-based) shipping
in the Lychee Pi Nano platform. At the other end is NXP Layerscape
LX2160A, a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O
aimed at infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to
devicetree, which opens up for removal of even more of their
platform-specific 'hwmod' description tables over the next few
releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (648 commits)
ARM: dts: suniv: Fix improper bindings include patch
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
ARM: dts: suniv: Fix improper bindings include patch
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
arm64: dts: ti: k3-am654: Enable main domain McSPI0
arm64: dts: ti: k3-am654: Add McSPI DT nodes
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
arm64: dts: ti: k3-am654-base-board: Enable ECAP PWM
arm64: dts: ti: k3-am65-main: Add ECAP PWM node
arm64: dts: ti: k3-am654-base-board: Add I2C nodes
arm64: dts: ti: am654-base-board: Add pinmux for main uart0
arm64: dts: ti: k3-am65: Add pinctrl regions
dt-bindings: pinctrl: k3: Introduce pinmux definitions
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug
console setups
- SoCFPGA adds explicit selection of ARM errata and removes some
unused code
This also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: omap2: avoid section mismatch warning
ARM: tegra: avoid section mismatch warning
ARM: ks8695: fix section mismatch warning
ARM: pxa: avoid section mismatch warning
ARM: mmp: fix pxa168_device_usb_phy use on aspenite
ARM: mmp: fix timer_init calls
ARM: OMAP1: fix USB configuration for device-only setups
ARM: OMAP1: add MMC configuration for Palm Tungsten E
ARM: imx: fix dependencies on imx7ulp
ARM: meson: select HAVE_ARM_TWD and ARM_GLOBAL_TIMER
MAINTAINERS: add drivers/soc/amlogic/ to amlogic list
ARM: imx: add initial support for imx7ulp
ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: davinci: da850-evm: remove unnecessary include
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/late
Samsung DTS ARM changes for v4.21, part 2
1. Add missing CPUs in cooling maps for Odroid X2 (missed in previous
round of fixups).
2. Fix clock configuration in audio subsystem on Odroid XU3/XU4.
* tag 'samsung-dt-4.21-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
ARM: dts: exynos: remove display-port node from Arndale
ARM: dts: exynos: Add opp-suspend to DMC and leftbus devfreq OPPs on Exynos4
ARM: dts: s5pv210: Add s5p-jpeg codec node.
ARM: dts: exynos: Use Samsung SoC specific compatible for DWC2 module
ARM: dts: exynos: Add all CPUs in cooling maps
ARM: dts: exynos: Clarify comment explaining purpose of Odroid XU3 DTSI
ARM: dts: exynos: Add pin configuration for SD write protect on Odroid XU3/XU4/HC1
ARM: dts: exynos: Update maximum frequency for eMMC to 200MHz on Odroid XU3/XU4
ARM: dts: exynos: Update maximum frequency for SD card to 200MHz on Odroid XU3/XU4/HC1
ARM: dts: exynos: Fix LDO13 min values on Odroid XU3/XU4/HC1
ARM: dts: exynos: Add UHS-I bus speed support to Odroid XU3/XU4/HC1
ARM: dts: exynos: Add missing clocks to RTC node for Arndale board
ARM: dts: exynos: Add compatible for s5m8767 clocks node on Itop Core
ARM: dts: exynos: Add compatible for s2mps11 clocks node on Exynos542x
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add interrupt support for UART in RDA Micro RDA8810PL SoC.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add timer support for RDA Micro RDA8810PL SoC.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add initial devicetree for Orange Pi i96 board from Xunlong. It
is one of the 96Boards IoT Edition board.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add initial devicetree support for OrangePi 2G IoT board from Xunlong.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add initial device tree for RDA8810PL SoC from RDA Microelectronics.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DTS ARM changes for v4.21, part 2
1. Add missing CPUs in cooling maps for Odroid X2 (missed in previous
round of fixups).
2. Fix clock configuration in audio subsystem on Odroid XU3/XU4.
* tag 'samsung-dt-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.21 - round 2
This is a small pull request for some lingering things that didn't make
the first round of patches.
First, the new suniv device tree included device tree headers for the
clock and reset indices. These header filers are going in through the
clock tree. Thus with the dt and core branches in arm-soc alone, it
doesn't build. One fix is included to remove the #include statements.
The defined macros aren't used yet as they were properly removed during
the review phase.
Second, Bluetooth using Broadcom (now Cypress) chips connected to UARTs
on various boards is enabled using serdev and the updated bindings for
Broadcom Bluetooth. The patch series had been sitting on the mailing
lists for a month, and the driver bits were just merged on 2018/12/19.
* tag 'sunxi-dt-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
ARM: dts: suniv: Fix improper bindings include patch
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Freescale QSPI device tree cleanup for 4.21:
- It contains a series from Schrempf Frieder that cleans up FSL QSPI
device tree nodes. The current device trees are broken because they
use an inconsistent scheme for assigning the reg properties. It
becomes a problem with ongoing QSPI driver under SPI framework. So
the cleanup is a preparation for new driver landing in the next
cycle.
* tag 'imx-qspi-dt-clean' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The clock and reset bindings are going through different trees, and while
the patch doesn't contain any value defined in that header, it still
includes those files and result in a build breakage when building the DT
without the matching clock and reset patches applied.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Add interconnect target module dts data for omaps for v4.21
This big set of changes adds SoC specific l4 interconnect target module
device tree data for am335x, am437x, omap5 and dra7 SoCs. We also move
existing devices to the right location in the l4 interconnect hierarcy.
This is similar to what we've already done for omap4 l4 interconnects
earlier, and follows what is documented in the ti-sysc driver dts binding
in Documentation/devicetree/bindings/bus/ti-sysc.txt.
These changes will essentially replace the struct ti_sysc and clock
entries in the arch/arm/mach-omap2/omap_hwmod_*_data.c files. Then a few
merge windows later, we can start dropping the built-in platform data
from the omap_hwmod_*_data.c files in favor of the device tree data only.
For now, we verify the device tree data module data against the built-in
data and warn about changes to prevent regressions.
With the device tree data, we are also probing devices with the ti-sysc
interconnect target module instead of omap_device. This fixes up the
handling for multiple device instances in a single interconnect target
module that has caused trouble earlier. A custom wrapper driver has been
needed earlier for such cases.
And as the device tree data is organized by the l4 interconnect instances,
we will be able to use genpd later on. This is because each interconnect
instance is also often also a single power domain.
This series of changes has been brewing for several months now. I did not
want to send a pull request earlier as people were still seeing device
specific issues until recently though. However, it turned out that all the
issues were quite trivial to fix. I had missed adding device tree ranges
for the l3 data port used on some devices, and I had missed converting the
device addresses for a few devices. And some devices like needed fixes for
deferred probe handling such as the EHCI PHY for built-in case on omap5.
Anyways, in case of trouble, we can easily just revert changes for a
single device if needed.
* tag 'omap-for-v4.21/dt-ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Cosmetic fix for omap5 USB node names
ARM: dts: Fix wrong address for omap5 sata phy
ARM: dts: Add missing ranges for dra7 mcasp l3 ports
ARM: dts: Fix ranges for am335x epwmss
ARM: dts: Fix hsi gdd range for omap4
ARM: dts: Add am335x mcasp with l3 data port ranges
ARM: dts: Add missing ranges for am437x mcasp l3 ports
ARM: dts: dra7: Move the ti,no-idle quirk on proper gmac node
ARM: dts: Revert am335x mcasp ti-sysc changes
ARM: dts: omap5: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: Use dra7 mcasp compatible for mcasp instances
ARM: dts: dra7: Move l4 child devices to probe them with ti-sysc
ARM: dts: dra7: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: am335x: Move l4 child devices to probe them with ti-sysc
ARM: dts: am335x: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: am437x: Move l4 child devices to probe them with ti-sysc
ARM: dts: am437x: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: dra7: convert to use new clkctrl layout
ARM: dts: am43xx: convert to use new clkctrl layout
ARM: dts: am33xx: convert to use new clkctrl layout
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
next/dt
arm: dts: zynq: DT changes for v5.0
- Fix mmc node name
* tag 'zynq-dt-for-v5.0' of https://github.com/Xilinx/linux-xlnx:
ARM: dts: Use mmc@ instead sdhci@
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch adds the Bluetooth node, and the underlying UART node if it's
missing, to the board device tree file for several boards. The LPO clock
is also added to the WiFi side's power sequencing node if it's missing,
to correctly represent the shared connections. There is also a PCM
connection for Bluetooth, but this is not covered in this patch.
These boards all have a WiFi+BT module from AMPAK, which contains one or
two Broadcom chips, depending on the model. The older AP6210 contains
two, while the newer AP6212 and AP6330 contain just one, as they use
two-in-one combo chips.
The Bluetooth side of the module is always connected to a UART on the
same pingroup as the SDIO pins for the WiFi side, in a 4 wire
configuration. Power to the VBAT and VDDIO pins are provided either by
the PMIC, using one or several of its regulator outputs, or other fixed
regulators on the board. The VBAT and VDDIO pins are shared with the
WiFi side, which would correspond to vmmc-supply and vqmmc-supply in the
mmc host node. A clock output from the SoC or the external X-Powers RTC
provides the LPO low power clock at 32.768 kHz.
All the boards covered in this patch are ones that do not require extra
changes to the SoC's dtsi file. For the remaining boards that I have
worked on, properties or device nodes for the LPO clock's source are
missing.
For the Cubietruck, the LPO clock is fed from CLK_OUT_A, which needs to
be muxed on pin PI12. This can be represented in multiple ways. This
patch puts the pinctrl property in the pin controller node. This is due
to limitations in Linux, where pinmux settings, even the same one, can
not be shared by multiple devices. Thus we cannot put it in both the
WiFi and Bluetooth device nodes. Putting it the CCU node is another
option, but Linux's CCU driver does not handle pinctrl. Also the pin
controller is guaranteed to be initialized after the CCU, when clocks
are available. And any other devices that use muxed pins are guaranteed
to be initialized after the pin controller. Thus having the CLK_OUT_A
pinmux reference be in the pin controller node is a good choice without
having to deal with implementation issues.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The clock and reset bindings are going through different trees, and while
the patch doesn't contain any value defined in that header, it still
includes those files and result in a build breakage when building the DT
without the matching clock and reset patches applied.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The "num-lanes" property for PCIe is not used, remove it.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
We will move the FSL QSPI driver to the SPI framework soon. To
prepare and to make sure the full buswidth is used (as it is with
the current driver), let's add the right properties.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The current driver does not use the reg properties, but we will
add a new driver soon. To make sure we have a consistent scheme,
let's fix the reg properties here.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The properties 'bus-num', 'fsl,spi-num-chipselects' and
'fsl,spi-flash-chipselects' were never read by the driver
and can be removed.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The assigned parent clocks should be normally specified in the consumer
device's DT node, this ensures respective driver always sees correct clock
settings when required.
This patch fixes regression in audio subsystem on Odroid XU3/XU4 boards
that appeared after commits:
commit 647d04f8e07a ("ASoC: samsung: i2s: Ensure the RCLK rate is properly determined")
commit 995e73e55f46 ("ASoC: samsung: i2s: Fix rclk_srcrate handling")
commit 48279c53fd1d ("ASoC: samsung: i2s: Prevent external abort on exynos5433 I2S1 access")
Without this patch the driver gets wrong clock as the I2S function clock
(op_clk) in probe() and effectively the clock which is finally assigned
from DT is not being enabled/disabled in the runtime resume/suspend ops.
Without the above listed commits the EXYNOS_I2S_BUS clock was always set
as parent of CLK_I2S_RCLK_SRC regardless of DT settings so there was no issue
with not enabled EXYNOS_SCLK_I2S.
Cc: <stable@vger.kernel.org> # 4.17.x
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
While updating cooling maps, the exynos4412-prime.dtsi was left
untouched. This is not a problem with Odroid U3 because it uses its own
map with fan (which was updated). However the cooling maps of Odroid X2
rely only on exynos4412-prime.dtsi.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
These should be now using offset from the module base and not the
full physical address.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The OLinuXino Lime2 has a big capacitor on its LDO3 output. It is
actually too large, causing the PMIC to shutdown when toggling the LDO3.
By enabling soft-start and ramp delay we increase the time for the
capacitor to charge lowering the current drain on the power regulator.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Looks like I missed converting the omap5 sata phy addresses to use offset
from the module base instead of full physical address.
While at it, we can also more it to be a direct child of the interconnect
target module, it is not really a child of the ocp2scp control device.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few device fixes for omaps
Here's a collection of minor fixes for annoying usability issues
people have noticed using various devices.
There are two regression fixes:
- A regression fix for omap5 usb3 dual role mode
- A regression fix to ams-delta audio being muted permanently
And two one-liners:
- Fix polarity for am335x-pdu001 SD card detection
- Fix non-working omap4-sdp Ethernet startup for rebind
It would be nice to get these merged during the -rc cycle if
possible. Naturally these can all wait for the merge window too
if we start running out of time.
* tag 'omap-for-v4.20/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Gemini DTS updates for v4.21:
- Fix the erroneous partition table on D-Link DIR-685
- Multiplex flash usage with other usage using pin control
handling (merged to the MTD tree)
- Use the RedBoot partition parser on SQ201
- Add the USB blocks (DT bindings merged in the last merge
window)
- Bump the debounce times a bit to avoid bouncing
* tag 'gemini-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Bump Gemini platforms to use 100ms debounce
ARM: dts: Add the FOTG210 USB host to Gemini boards
ARM: dts: Fix up SQ201 flash access
ARM: dts: Enable Gemini flash access
ARM: dts: Fix up the D-Link DIR-685 MTD partition info
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner H3/H5 changes for 4.21
Our usual pull request with the changes shared between the H3 and H5 SoCs.
The major changes for this release are:
- Addition of the video engine for the H5
- H3 Camera support
- New board: Emlid Neutis N5, Mapleboard MP130
* tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: Add Video Engine node
ARM/arm64: dts: allwinner: Move H3/H5 syscon label over to soc-specific nodes
arm64: dts: allwinner: h5: Add system-control node with SRAM C1
ARM: dts: sun8i: h3: Fix the system-control register range
ARM: dts: sun8i: Add the H3/H5 CSI controller
ARM: dts: sun8i-h3: Add dts for the Mapleboard MP130
arm64: dts: allwinner: new board - Emlid Neutis N5
dt-bindings: vendor-prefix: new vendor - Emlid
ARM: dts: sun8i-h3: add sy8106a to orange pi plus
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
RV1108 improvements (uart-dma, clocks, interrupt numbers, gmac support
timer and emmc pins) from its first real-world user.
RK3188 improvements (OPPv2, cpu node updates) to prepare for a new
devicetree, the BQ Edison 2 Quad-Core.
VPU device node for rk3288, right now only the jpeg encoder part
will be in the kernel but hopefully other codecs will follow.
* tag 'v4.21-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add internal timer support for rv1108
ARM: dts: rockchip: add BQ Edison 2 QC devicetree
ARM: dts: rockchip: add VPU device node for RK3288
ARM: dts: rockchip: update cpu supplies on rk3188
ARM: dts: rockchip: add phandles to secondary cpu cores
ARM: dts: rockchip: add cpu-core resets for rk3188
ARM: dts: rockchip: convert rk3188 to opp-v2
ARM: dts: rockchip: add #sound-dai-cells to Cortex-A9 i2s
ARM: dts: rockchip: Add UART DMA support for rv1108
ARM: dts: rockchip: Assign the proper GPIO clocks for rv1108
ARM: dts: rockchip: Fix the PMU interrupt number for rv1108
ARM: dts: rockchip: Pass the 'arm,cpu-registers-not-fw-configured' property on rv1108
ARM: dts: rockchip: Pass the 'clock-latency' property on rv1108
ARM: dts: rockchip: Add rv1108 GMAC support
ARM: dts: rockchip: add rv1108 eMMC pin settings
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into next/dt
AT91 DT for 4.21
- Switch most platforms to the new clock binding
- Small improvement for Axentia nattis
* tag 'at91-4.21-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: nattis: initialize the BLON pin as output-low early
ARM: dts: at91: at91sam9rl: switch to new clock bindings
ARM: dts: at91: at91sam9x5: switch to new clock bindings
ARM: dts: at91: at91sam9263: switch to new clock bindings
ARM: dts: at91: at91sam9261: switch to new clock bindings
ARM: dts: at91: at91sam9260: switch to new clock bindings
ARM: dts: at91: sama5d2: switch to new clock binding
ARM: dts: at91: sama5d4: switch to new clock bindings
ARM: dts: at91: sama5d2: use the divided clock for SMC
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
ARM: dts: Amlogic updates for v4.21, round 2
Highlights
- add CPU OPP tables
- timers: add global timer and TWD
* tag 'amlogic-dt-2' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson: meson8b: add the CPU OPP tables
ARM: dts: meson: meson8: add the CPU OPP table
ARM: dts: meson8b: add the Cortex-A5 global timer
ARM: dts: meson8b: add the ARM TWD timer
ARM: dts: meson8: add the Cortex-A9 global timer
ARM: dts: meson8: add the ARM TWD timer
ARM: dts: meson: group the Cortex-A5 / Cortex-A9 peripherals
dt-bindings: clock: meson8b: export the CPU post dividers
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt
UniPhier ARM SoC DT updates for v4.21
- Add bindings for all SoCs/boards of UniPhier platform
- Move binding docs to socionext directory
- Add all CPUs in cooling maps
- Add MIO DMAC nodes
* tag 'uniphier-dt-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: add MIO DMAC nodes
arm64: dts: uniphier: Add all CPUs in cooling maps
ARM: dts: uniphier: Add all CPUs in cooling maps
dt-bindings: uniphier: move cache-uniphier.txt to vendor directory
dt-bindings: uniphier: add bindings for UniPhier SoC family
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX7ULP device tree for 4.21:
- It includes the initial device tree for i.MX7ULP SoC and EVK board
support.
* tag 'imx7ulp-dt-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx: add imx7ulp evk support
ARM: dts: imx: add common imx7ulp dtsi support
dt-bindings: fsl: add imx7ulp pm related components bindings
dt-bindings: fsl: add compatible for imx7ulp evk
clk: imx: add imx7ulp clk driver
clk: imx: implement new clk_hw based APIs
clk: imx: make mux parent strings const
dt-bindings: clock: add imx7ulp clock binding doc
clk: imx: add imx7ulp composite clk support
clk: imx: add pfdv2 support
clk: imx: add pllv4 support
clk: fractional-divider: add CLK_FRAC_DIVIDER_ZERO_BASED flag support
clk: imx: add gatable clock divider support
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX7D PICO boards update for 4.21:
- It contains a series from Otavio Salvador that improves i.MX7D PICO
SoM, and then adds Hobbit baseboard support on top of the improvement.
* tag 'imx7d-pico-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7d-pico: Add the imx7d-pico-hobbit variant
ARM: dts: imx7d-pico-pi: Extend peripherals support
ARM: dts: imx7d-pico: Extend peripherals support
ARM: dts: imx7d-pico: Improve WiFi regulator name
ARM: dts: imx7d-pico: Pass the Ethernet PHY reset GPIO
ARM: dts: imx7d-pico: Pass the USBOTG1_PWR pinctrl
ARM: dts: imx7d-pico-pi: Move SoM related part to imx7d-pico.dtsi
ARM: dts: imx7d-pico: Switch to SPDX identifier
ARM: dts: imx7d-pico: Do not harcode the memory size
ARM: dts: imx7d-nitrogen7: Fix the description of the Wifi clock
ARM: imx: update the cpu power up timing setting on i.mx6sx
ARM: dts: imx7d-pico: Describe the Wifi clock
ARM: dts: imx51-zii-rdu1: Remove EEPROM node
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree update for 4.21:
- New boards support: emtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
and vf610 based Liebherr's BK4 device, ZII SCU4 AIB board.
- Add flexcan support for i.MX6UL SoC, turn on stop mode wakeup feature
for flexcan, and enable devices on a few i.MX6 NXP boards.
- Enable AUO G101EVN010 lcd panel and Goodix touch support for
imx6ul-ccimx6ulsbcpro board.
- Enable sensors support for imx6qdl-sabresd board: egalax touch, light,
magnetometer and accelerometer sensor.
- Switch more boards to use SPDX identifier.
- Fix memory node duplication in i.MX device tree sources.
- Correct GIC PPI interrupts mask for i.MX6UL and i.MX7 SoCs.
- Drop 'snps,dw-pcie' compatible from LS1021A PCIe device to avoid
incorrect device matching.
- Add the gpu nodes for the adreno 200 GPU on iMX51 and iMX53, which
are now supported by the freedreno driver.
- Add DCP device support for i.MX6ULL, which requires explicit clock
enabling.
- Add '#thermal-sensor-cells' for thermal device and '#cooling-cells'
for cooling devices.
- Add missing clock information for EPIT on i.MX25 SoC.
- Add PWM and qdma devices for LS1021A SoC.
- Update cooling maps of LS1021A SoC to include all devices affected by
individual trip points.
- Random device addition and cleanup on various boards.
* tag 'imx-dt-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (82 commits)
ARM: dts: imx51-zii-rdu1: Do not specify "power-gpio" for hpa1
ARM: dts: imx6ul: Remove extra space between node name and brace
ARM: dts: imx6qdl-sabresd: Use GPIO_ACTIVE_HIGH for regulators
ARM: dts: imx6ul: add flexcan support
ARM: dts: imx5: add gpu nodes
ARM: dts: imx6qdl-sabresd: add accelerometer sensor support
ARM: dts: imx6qdl-sabresd: add magnetometer sensor support
ARM: dts: imx6qdl-sabresd: add light sensor support
ARM: dts: imx6qdl-sabresd: Move regulators outside of "simple-bus"
ARM: dts: imx6qdl: Fix memory node duplication
ARM: dts: imx6dl-mamoj: Add a memory node
ARM: dts: imx53-voipac-dmm-668: Fix memory node duplication
ARM: dts: vf610-zii-scu4-aib: Add HI8435 support
ARM: dts: imx6qdl-sabresd: add egalax touch screen support on i2c2 bus
ARM: dts: imx7s: Add flexcan stop mode wakeup support
ARM: dts: imx6ul: Add flexcan stop mode wakeup support
ARM: dts: imx6qdl: Add flexcan stop mode wakeup support
ARM: dts: imx6sx: Add flexcan stop mode wakeup support
ARM: dts: imx6ul-pico: Add the imx6ul-pico-pi variant
ARM: dts: imx6ul-pico-hobbit: Extend peripherals support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DTS ARM changes for v4.21
1. Add missing properties and nodes for PMIC clocks in multiple DTS
files.
2. Add UHS-I bus speed support to Odroid XU3/XU4/HC SD card and bump the
maximum clock frequency to 200 MHz for SD and eMMC.
3. Update cooling maps to include all CPU devices in multiple DTS files.
4. Enable quirks for Exynos3250 DWC.
5. Add JPEG CODEC node to S5Pv210.
6. Add opp-suspend to devfreq OPPs on Exynos4 boards to fix resuming
from suspend to RAM.
7. Remove eDP from Arndale board as it does not work and breaks also
DSI.
* tag 'samsung-dt-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: remove display-port node from Arndale
ARM: dts: exynos: Add opp-suspend to DMC and leftbus devfreq OPPs on Exynos4
ARM: dts: s5pv210: Add s5p-jpeg codec node.
ARM: dts: exynos: Use Samsung SoC specific compatible for DWC2 module
ARM: dts: exynos: Add all CPUs in cooling maps
ARM: dts: exynos: Clarify comment explaining purpose of Odroid XU3 DTSI
ARM: dts: exynos: Add pin configuration for SD write protect on Odroid XU3/XU4/HC1
ARM: dts: exynos: Update maximum frequency for eMMC to 200MHz on Odroid XU3/XU4
ARM: dts: exynos: Update maximum frequency for SD card to 200MHz on Odroid XU3/XU4/HC1
ARM: dts: exynos: Fix LDO13 min values on Odroid XU3/XU4/HC1
ARM: dts: exynos: Add UHS-I bus speed support to Odroid XU3/XU4/HC1
ARM: dts: exynos: Add missing clocks to RTC node for Arndale board
ARM: dts: exynos: Add compatible for s5m8767 clocks node on Itop Core
ARM: dts: exynos: Add compatible for s2mps11 clocks node on Exynos542x
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.21
This is a quite big pull request this time, with a huge number of changes
(and patches) due to us fixing the vast majority of the DTC warnings our DT
had.
We also have a bunch of other good, more meaningful, changes:
- Support for the new Allwinner T3 (rebranded R40) and f1c100s (armv5)
SoCs
- AXP803 PMIC AC Power supply support
- Rework of the oscillators tree
- Two new boards: the t3-cqa3t-bv3 and Lichee Pi Nano
Plus a few enhancements here and there.
* tag 'sunxi-dt-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (84 commits)
ARM: dts: sunxi: Fix PMU compatible strings
ARM: dts: sun8i: r40: Add RTC device node
ARM: dts: sunxi: h3/h5: Fix up RTC device node and clock references
ARM: dts: sun8i: a23/a33: Fix up RTC device node
ARM: dts: sun8i: r40: Add clock accuracy for external oscillators
ARM: dts: sunxi: h3/h5: Add clock accuracy for external oscillators
ARM: dts: sun8i: a33: Drop audio codec oversampling rate to 128 fs
ARM: dts: sun8i: h3: Remove unnecessary reserved memory node
ARM: dts: sun8i: a33: Remove unnecessary reserved memory node
ARM: dts: suniv: Add device tree for Lichee Pi Nano
ARM: dts: suniv: add initial DTSI file for F1C100s
ARM: dts: axp81x: add AC power supply subnode
ARM: dts: sun8i: v3s: Remove skeleton and memory to avoid warnings
ARM: dts: sun8i: v3s: Provide default muxing for relevant controllers
ARM: dts: sun8i: v3s: Change pinctrl nodes to avoid warning
ARM: dts: sun8i: v3s: Change LRADC node names to avoid warnings
ARM: dts: sun8i: h3: Remove leading zeros from unit-addresses
ARM: dts: sun8i: BPI-M2M: Remove i2c nodes
ARM: dts: sun8i: a23/a33: Provide default muxing for relevant controllers
ARM: dts: sunxi: reference: Move the muxing back to the common DTSI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add support for the internal timer peripheral on RV1108.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
ARM: tegra: Device tree changes for v4.21-rc1
These changes add the external memory controller on Tegra20 as well as
the VIC on Tegra124.
* tag 'tegra-for-4.21-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Add VIC on Tegra124
ARM: dts: tegra20: Add clock entry to External Memory Controller
ARM: dts: tegra20: Add interrupt entry to External Memory Controller
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.21
* RZ/G1N (r8a7744) SoC
- Describe in DT: SYS-DMAC, GPIO, Ethernet AVB, SMP, [H]SCIF{A|B},
I2C, USB 2.0 and 3.0 hosts, USB-DMAC, HSUSB, RWDT, Audio, CAN, IRQC,
thermal, CMT, VIN, VSP, IPMMU, PMU, TPU, QSPI MSIOF, and PCIE
- iWave G20D-Q7 board
- Initial support
- Enable eMMC, SDHI and SPIO NOR support
- Add camera daughterboard
* RZ/G1M (r8a7743) SoC
- Remove legacy "renesas,rcar-thermal" compatibility
* tag 'renesas-arm-dt2-for-v4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (34 commits)
ARM: dts: r8a7744-iwg20m: Add SPI NOR support
ARM: dts: iwg20d-q7-common: Move cmt/rwdt node out of RZ/G1M SOM
ARM: dts: r8a7744: Add PCIe Controller device node
ARM: dts: r8a7744: Add xhci support
ARM: dts: r8a7744: Add MSIOF[012] support
ARM: dts: r8a7744: Add QSPI support
ARM: dts: r8a7744-iwg20d-q7-dbcm-ca: Add device tree for camera DB
ARM: dts: r8a7744: Add TPU support
ARM: dts: r8a7744: Add PWM SoC support
ARM: dts: r8a7744: Add IPMMU DT nodes
ARM: dts: r8a7744: Add VSP support
ARM: dts: r8a7744: add VIN dt support
ARM: dts: r8a7744: Add CMT SoC specific support
ARM: dts: r8a7744: Add thermal device to DT
ARM: dts: r8a7744: Add IRQC support
ARM: dts: r8a7744: Add CAN support
ARM: dts: r8a7744: Add audio support
ARM: dts: r8a7744: Add RWDT node
ARM: dts: r8a7744: Add USB-DMAC and HSUSB device nodes
ARM: dts: r8a7744: USB 2.0 host support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt
ASPEED device tree updates for 4.20
- New machine: Facebook Backpack-CMM BMC and flash layout
- OpenPower reference systems (Palmetto P8, Romulus P9) move to the
ColdFire based FSI driver
- Misc device tree updates from the OpenBMC project
* tag 'aspeed-4.21-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: Add Facebook Backpack-CMM BMC
ARM: dts: Add Facebook BMC flash layout
ARM: dts: aspeed: wspoon: Enable iio-hwmon battery
ARM: dts: aspeed: romulus: Enable iio-hwmon-battery
ARM: dts: aspeed: Enable VHUB on Romulus
ARM: dts: aspeed-palmetto: Add LPC control node
ARM: dts: aspeed: Palmetto system can use coprocessor for FSI
ARM: dts: aspeed: Romulus system can use coprocessor for FSI
Signed-off-by: Olof Johansson <olof@lixom.net>
|
