| Age | Commit message (Collapse) | Author |
|---|
|
commit 10f1d5d111e8aed46a0f1179faf9a3cf422f689e upstream.
There's a race condition between the atomic_dec_and_test(&io->count)
in dec_count() and the waking of the sync_io() thread. If the thread
is spuriously woken immediately after the decrement it may exit,
making the on stack io struct invalid, yet the dec_count could still
be using it.
Fix this race by using a completion in sync_io() and dec_count().
Reported-by: Minfei Huang <huangminfei@ucloud.cn>
Signed-off-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
[bwh: Backported to 3.2: use wait_for_completion() as wait_for_completion_io()
is not available]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 76252723e88681628a3dbb9c09c963e095476f73 upstream.
To properly re-initialize SR-IOV it is necessary to reset the device
even if it is already down. Not doing this may result in Tx unit hangs.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 5a7fbe7e9ea0b1b9d7ffdba64db1faa3a259164c upstream.
This patch adds PID 0x0003 to the VID 0x128d (Testo). At least the
Testo 435-4 uses this, likely other gear as well.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 16927776ae757d0d132bdbfabbfe2c498342bd59 upstream.
Sharvil noticed with the posix timer_settime interface, using the
CLOCK_REALTIME_ALARM or CLOCK_BOOTTIME_ALARM clockid, if the users
tried to specify a relative time timer, it would incorrectly be
treated as absolute regardless of the state of the flags argument.
This patch corrects this, properly checking the absolute/relative flag,
as well as adds further error checking that no invalid flag bits are set.
Reported-by: Sharvil Nanavati <sharvil@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Sharvil Nanavati <sharvil@google.com>
Link: http://lkml.kernel.org/r/1404767171-6902-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit f6c2dd20108c35e30e2c1f3c6142d189451a626b upstream.
It is customary to clamp limits instead of bailing out with an error
if a configured limit is out of the range supported by the driver.
This simplifies limit configuration, since the user will not typically
know chip and/or driver specific limits.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 233a01fa9c4c7c41238537e8db8434667ff28a2f upstream.
If the number in "user_id=N" or "group_id=N" mount options was larger than
INT_MAX then fuse returned EINVAL.
Fix this to handle all valid uid/gid values.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
[bwh: Backported to 3.2: no user namespace conversion]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 126b9d4365b110c157bc4cbc32540dfa66c9c85a upstream.
As suggested by checkpatch.pl, use time_before64() instead of direct
comparison of jiffies64 values.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 145e74a4e5022225adb84f4e5d4fff7938475c35 upstream.
Upper limit for write operations to temperature limit registers
was clamped to a fractional value. However, limit registers do
not support fractional values. As a result, upper limits of 127.5
degrees C or higher resulted in a rounded limit of 128 degrees C.
Since limit registers are signed, this was stored as -128 degrees C.
Clamp limits to (-55, +127) degrees C to solve the problem.
Value on writes to auto_temp[12]_min and auto_temp[12]_max were not
clamped at all, but masked. As a result, out-of-range writes resulted
in a more or less arbitrary limit. Clamp those attributes to (0, 127)
degrees C for more predictable results.
Cc: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[bwh: Backported to 3.2:
- Adjust context
- Driver was using SENSORS_LIMIT(), which we can replace with clamp_val()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 75646e758a0ecbed5024454507d5be5b9ea9dcbf upstream.
Some machines (eg. Lenovo Z480) ECs are not stable during boot up
and causes battery driver fails to be loaded due to failure of getting
battery information from EC sometimes. After several retries, the
operation will work. This patch is to retry to get battery information 5
times if the first try fails.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=75581
Reported-and-tested-by: naszar <naszar@ya.ru>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bwh: Backported to 3.2: acpi_battery_update() doesn't take a second parameter]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c0d653412fc8450370167a3268b78fc772ff9c87 upstream.
There is a race condition in ec_transaction_completed().
When ec_transaction_completed() is called in the GPE handler, it could
return true because of (ec->curr == NULL). Then the wake_up() invocation
could complete the next command unexpectedly since there is no lock between
the 2 invocations. With the previous cleanup, the IBF=0 waiter race need
not be handled any more. It's now safe to return a flag from
advance_condition() to indicate the requirement of wakeup, the flag is
returned from a locked context.
The ec_transaction_completed() is now only invoked by the ec_poll() where
the ec->curr is ensured to be different from NULL.
After cleaning up, the EVT_SCI=1 check should be moved out of the wakeup
condition so that an EVT_SCI raised with (ec->curr == NULL) can trigger a
QR_SC command.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70891
Link: https://bugzilla.kernel.org/show_bug.cgi?id=63931
Link: https://bugzilla.kernel.org/show_bug.cgi?id=59911
Reported-and-tested-by: Gareth Williams <gareth@garethwilliams.me.uk>
Reported-and-tested-by: Hans de Goede <jwrdegoede@fedoraproject.org>
Reported-by: Barton Xu <tank.xuhan@gmail.com>
Tested-by: Steffen Weber <steffen.weber@gmail.com>
Tested-by: Arthur Chen <axchen@nvidia.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 9b80f0f73ae1583c22325ede341c74195847618c upstream.
After we've added the first command byte write into advance_transaction(),
the IBF=0 waiter is duplicated with the command completion waiter
implemented in the ec_poll() because:
If IBF=1 blocked the first command byte write invoked in the task
context ec_poll(), it would be kicked off upon IBF=0 interrupt or timed
out and retried again in the task context.
Remove this seperate and duplicate IBF=0 waiter. By doing so we can
reduce the overall number of times to access the EC_SC(R) status
register.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70891
Link: https://bugzilla.kernel.org/show_bug.cgi?id=63931
Link: https://bugzilla.kernel.org/show_bug.cgi?id=59911
Reported-and-tested-by: Gareth Williams <gareth@garethwilliams.me.uk>
Reported-and-tested-by: Hans de Goede <jwrdegoede@fedoraproject.org>
Reported-by: Barton Xu <tank.xuhan@gmail.com>
Tested-by: Steffen Weber <steffen.weber@gmail.com>
Tested-by: Arthur Chen <axchen@nvidia.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit f92fca0060fc4dc9227342d0072d75df98c1e5a5 upstream.
Move the first command byte write into advance_transaction() so that all
EC register accesses that can affect the command processing state machine
can happen in this asynchronous state machine advancement function.
The advance_transaction() function then can be a complete implementation
of an asyncrhonous transaction for a single command so that:
1. The first command byte can be written in the interrupt context;
2. The command completion waiter can also be used to wait the first command
byte's timeout;
3. In BURST mode, the follow-up command bytes can be written in the
interrupt context directly, so that it doesn't need to return to the
task context. Returning to the task context reduces the throughput of
the BURST mode and in the worst cases where the system workload is very
high, this leads to the hardware driven automatic BURST mode exit.
In order not to increase memory consumption, convert 'done' into 'flags'
to contain multiple indications:
1. ACPI_EC_COMMAND_COMPLETE: converting from original 'done' condition,
indicating the completion of the command transaction.
2. ACPI_EC_COMMAND_POLL: indicating the availability of writing the first
command byte. A new command can utilize this flag to compete for the
right of accessing the underlying hardware. There is a follow-up bug
fix that has utilized this new flag.
The 2 flags are important because it also reflects a key concept of IO
programs' design used in the system softwares. Normally an IO program
running in the kernel should first be implemented in the asynchronous way.
And the 2 flags are the most common way to implement its synchronous
operations on top of the asynchronous operations:
1. POLL: This flag can be used to block until the asynchronous operations
can happen.
2. COMPLETE: This flag can be used to block until the asynchronous
operations have completed.
By constructing code cleanly in this way, many difficult problems can be
solved smoothly.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70891
Link: https://bugzilla.kernel.org/show_bug.cgi?id=63931
Link: https://bugzilla.kernel.org/show_bug.cgi?id=59911
Reported-and-tested-by: Gareth Williams <gareth@garethwilliams.me.uk>
Reported-and-tested-by: Hans de Goede <jwrdegoede@fedoraproject.org>
Reported-by: Barton Xu <tank.xuhan@gmail.com>
Tested-by: Steffen Weber <steffen.weber@gmail.com>
Tested-by: Arthur Chen <axchen@nvidia.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bwh: Backported to 3.2:
- Adjust context
- s/ec->lock/ec->curr_lock/]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit a3cd8d2789c2e265e09377f260e7d2ac9cec81bb upstream.
Currently when advance_transaction() is called in EC interrupt handler,
if there is nothing driver can do with the interrupt, it will be taken
as a false one.
But this is not always true, as there may be a SCI EC interrupt fired
during normal read/write operation, which should not be counted as a
false one. This patch fixes the problem.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 66b42b78bc1e816f92b662e8888c89195e4199e1 upstream.
The advance_transaction() will be invoked from the IRQ context GPE handler
and the task context ec_poll(). The handling of this function is locked so
that the EC state machine are ensured to be advanced sequentially.
But there is a problem. Before invoking advance_transaction(), EC_SC(R) is
read. Then for advance_transaction(), there could be race condition around
the lock from both contexts. The first one reading the register could fail
this race and when it passes the stale register value to the state machine
advancement code, the hardware condition is totally different from when
the register is read. And the hardware accesses determined from the wrong
hardware status can break the EC state machine. And there could be cases
that the functionalities of the platform firmware are seriously affected.
For example:
1. When 2 EC_DATA(W) writes compete the IBF=0, the 2nd EC_DATA(W) write may
be invalid due to IBF=1 after the 1st EC_DATA(W) write. Then the
hardware will either refuse to respond a next EC_SC(W) write of the next
command or discard the current WR_EC command when it receives a EC_SC(W)
write of the next command.
2. When 1 EC_SC(W) write and 1 EC_DATA(W) write compete the IBF=0, the
EC_DATA(W) write may be invalid due to IBF=1 after the EC_SC(W) write.
The next EC_DATA(R) could never be responded by the hardware. This is
the root cause of the reported issue.
Fix this issue by moving the EC_SC(R) access into the lock so that we can
ensure that the state machine is advanced consistently.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70891
Link: https://bugzilla.kernel.org/show_bug.cgi?id=63931
Link: https://bugzilla.kernel.org/show_bug.cgi?id=59911
Reported-and-tested-by: Gareth Williams <gareth@garethwilliams.me.uk>
Reported-and-tested-by: Hans de Goede <jwrdegoede@fedoraproject.org>
Reported-by: Barton Xu <tank.xuhan@gmail.com>
Tested-by: Steffen Weber <steffen.weber@gmail.com>
Tested-by: Arthur Chen <axchen@nvidia.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bwh: Backported to 3.2:
- Adjust context
- Use PREFIX in log message]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 36b15875a7819a2ec4cb5748ff7096ad7bd86cbb upstream.
A bug was introduced by commit b76b51ba0cef ('ACPI / EC: Add more debug
info and trivial code cleanup') that erroneously caused the struct member
to be accessed before acquiring the required lock. This change fixes
it by ensuring the lock acquisition is done first.
Found by Aaron Durbin <adurbin@chromium.org>
Fixes: b76b51ba0cef ('ACPI / EC: Add more debug info and trivial code cleanup')
References: http://crbug.com/319019
Signed-off-by: Puneet Kumar <puneetster@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
[olof: Commit message reworded a bit]
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b76b51ba0cef13980813373a548a12206e3cd3c9 upstream.
Add more debug info for EC transaction debugging, like the interrupt
status register value, the detail info of a EC transaction.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 3d28bd840b2d3981cd28caf5fe1df38f1344dd60 upstream.
Add ID of the Telewell 4G v2 hardware to option driver to get legacy
serial interface working
Signed-off-by: Bernd Wachter <bernd.wachter@jolla.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b9326057a3d8447f5d2e74a7b521ccf21add2ec0 upstream.
Corsair USB Dongles are shipped with Corsair AXi series PSUs.
These are cp210x serial usb devices, so make driver detect these.
I have a program, that can get information from these PSUs.
Tested with 2 different dongles shipped with Corsair AX860i and
AX1200i units.
Signed-off-by: Andras Kovacs <andras@sth.sze.hu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 5dd214248f94d430d70e9230bda72f2654ac88a8 upstream.
The mount manpage says of the max_batch_time option,
This optimization can be turned off entirely
by setting max_batch_time to 0.
But the code doesn't do that. So fix the code to do
that.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[bwh: Backported to 3.2: option parsing looks different]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ae0f78de2c43b6fadd007c231a352b13b5be8ed2 upstream.
Make it clear that values printed are times, and that it is error
since last fsck. Also add note about fsck version required.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 1035a9e3e9c76b64a860a774f5b867d28d34acc2 upstream.
Writing to fanX_div does not clear the cache. As a result, reading
from fanX_div may return the old value for up to two seconds
after writing a new value.
This patch ensures the fan_div cache is updated in set_fan_div().
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit df86754b746e9a0ff6f863f690b1c01d408e3cdc upstream.
temp2_input should not be writable, fix it.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 4e578080ed3262ed2c3985868539bc66218d25c0 upstream.
Commit "drm/vmwgfx: correct fb_fix_screeninfo.line_length", while fixing a
vmwgfx fbdev bug, also writes the pitch to a supposedly read-only register:
SVGA_REG_BYTES_PER_LINE, while it should be (and also in fact is) written to
SVGA_REG_PITCHLOCK.
This patch is Cc'd stable because of the unknown effects writing to this
register might have, particularly on older device versions.
v2: Updated log message.
Cc: Christopher Friedt <chrisfriedt@gmail.com>
Tested-by: Christopher Friedt <chrisfriedt@gmail.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 43d826ca5979927131685cc2092c7ce862cb91cd upstream.
We should always prefer to use full RTS protection. Using
CTS to self gives a meaningless improvement, but this flow
is much harder for the firmware which is likely to have
issues with it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[bwh: Backported to 3.2:
- Adjust filename
- Condition for RXON_FLG_SELF_CTS_EN in iwlagn_commit_rxon() was different]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 1b6478231c6f5f844185acb32045cf195028cfce upstream.
Calling xen_console_resume() in xen_suspend() causes a warning because
it locks irq_mapping_update_lock (a mutex) and this may sleep. If a
userspace process is using the evtchn device then this mutex may be
locked at the point of the stop_machine() call and
xen_console_resume() would then deadlock.
Resuming the console after stop_machine() returns avoids this
deadlock.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 133d4527eab8d199a62eee6bd433f0776842df2e upstream.
When we write to a degraded array which has a bitmap, we
make sure the relevant bit in the bitmap remains set when
the write completes (so a 're-add' can quickly rebuilt a
temporarily-missing device).
If, immediately after such a write starts, we incorporate a spare,
commence recovery, and skip over the region where the write is
happening (because the 'needs recovery' flag isn't set yet),
then that write will not get to the new device.
Once the recovery finishes the new device will be trusted, but will
have incorrect data, leading to possible corruption.
We cannot set the 'needs recovery' flag when we start the write as we
do not know easily if the write will be "degraded" or not. That
depends on details of the particular raid level and particular write
request.
This patch fixes a corruption issue of long standing and so it
suitable for any -stable kernel. It applied correctly to 3.0 at
least and will minor editing to earlier kernels.
Reported-by: Bill <billstuff2001@sbcglobal.net>
Tested-by: Bill <billstuff2001@sbcglobal.net>
Link: http://lkml.kernel.org/r/53A518BB.60709@sbcglobal.net
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b292d7a10487aee6e74b1c18b8d95b92f40d4a4f upstream.
Currently, any NMI is falsely handled by a NMI handler of NMI watchdog
if CondChgd bit in MSR_CORE_PERF_GLOBAL_STATUS MSR is set.
For example, we use external NMI to make system panic to get crash
dump, but in this case, the external NMI is falsely handled do to the
issue.
This commit deals with the issue simply by ignoring CondChgd bit.
Here is explanation in detail.
On x86 NMI watchdog uses performance monitoring feature to
periodically signal NMI each time performance counter gets overflowed.
intel_pmu_handle_irq() is called as a NMI_LOCAL handler from a NMI
handler of NMI watchdog, perf_event_nmi_handler(). It identifies an
owner of a given NMI by looking at overflow status bits in
MSR_CORE_PERF_GLOBAL_STATUS MSR. If some of the bits are set, then it
handles the given NMI as its own NMI.
The problem is that the intel_pmu_handle_irq() doesn't distinguish
CondChgd bit from other bits. Unlike the other status bits, CondChgd
bit doesn't represent overflow status for performance counters. Thus,
CondChgd bit cannot be thought of as a mark indicating a given NMI is
NMI watchdog's.
As a result, if CondChgd bit is set, any NMI is falsely handled by the
NMI handler of NMI watchdog. Also, if type of the falsely handled NMI
is either NMI_UNKNOWN, NMI_SERR or NMI_IO_CHECK, the corresponding
action is never performed until CondChgd bit is cleared.
I noticed this behavior on systems with Ivy Bridge processors: Intel
Xeon CPU E5-2630 v2 and Intel Xeon CPU E7-8890 v2. On both systems,
CondChgd bit in MSR_CORE_PERF_GLOBAL_STATUS MSR has already been set
in the beginning at boot. Then the CondChgd bit is immediately cleared
by next wrmsr to MSR_CORE_PERF_GLOBAL_CTRL MSR and appears to remain
0.
On the other hand, on older processors such as Nehalem, Xeon E7540,
CondChgd bit is not set in the beginning at boot.
I'm not sure about exact behavior of CondChgd bit, in particular when
this bit is set. Although I read Intel System Programmer's Manual to
figure out that, the descriptions I found are:
In 18.9.1:
"The MSR_PERF_GLOBAL_STATUS MSR also provides a ¡sticky bit¢ to
indicate changes to the state of performancmonitoring hardware"
In Table 35-2 IA-32 Architectural MSRs
63 CondChg: status bits of this register has changed.
These are different from the bahviour I see on the actual system as I
explained above.
At least, I think ignoring CondChgd bit should be enough for NMI
watchdog perspective.
Signed-off-by: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/20140625.103503.409316067.d.hatayama@jp.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b14bf2d0c0358140041d1c1805a674376964d0e0 upstream.
Some buggy JMicron USB-ATA bridges don't know how to translate the FUA
bit in READs or WRITEs. This patch adds an entry in unusual_devs.h
and a blacklist flag to tell the sd driver not to use FUA.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Michael Büsch <m@bues.ch>
Tested-by: Michael Büsch <m@bues.ch>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2:
- Adjust context
- Use sd_printk() not sd_first_printk()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit f35f71244da6e51db4e1f2c7e318581f498ececf upstream.
It appears that no one ever run ffs-test on a big-endian machine,
since it used cpu-endianess for fs_count and hs_count fields which
should be in little-endian format. Fix by wrapping the numbers in
cpu_to_le32.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 76f47128f9b33af1e96819746550d789054c9664 upstream.
An NFS operation that creates a new symlink includes the symlink data,
which is xdr-encoded as a length followed by the data plus 0 to 3 bytes
of zero-padding as required to reach a 4-byte boundary.
The vfs, on the other hand, wants null-terminated data.
The simple way to handle this would be by copying the data into a newly
allocated buffer with space for the final null.
The current nfsd_symlink code tries to be more clever by skipping that
step in the (likely) case where the byte following the string is already
0.
But that assumes that the byte following the string is ours to look at.
In fact, it might be the first byte of a page that we can't read, or of
some object that another task might modify.
Worse, the NFSv4 code tries to fix the problem by actually writing to
that byte.
In the NFSv2/v3 cases this actually appears to be safe:
- nfs3svc_decode_symlinkargs explicitly null-terminates the data
(after first checking its length and copying it to a new
page).
- NFSv2 limits symlinks to 1k. The buffer holding the rpc
request is always at least a page, and the link data (and
previous fields) have maximum lengths that prevent the request
from reaching the end of a page.
In the NFSv4 case the CREATE op is potentially just one part of a long
compound so can end up on the end of a page if you're unlucky.
The minimal fix here is to copy and null-terminate in the NFSv4 case.
The nfsd_symlink() interface here seems too fragile, though. It should
really either do the copy itself every time or just require a
null-terminated string.
Reported-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d76744a93246eccdca1106037e8ee29debf48277 upstream.
https://bugzilla.kernel.org/show_bug.cgi?id=70191
https://bugzilla.kernel.org/show_bug.cgi?id=77581
It is observed that sometimes Tx packet is downloaded without
adding driver's txpd header. This results in firmware parsing
garbage data as packet length. Sometimes firmware is unable
to read the packet if length comes out as invalid. This stops
further traffic and timeout occurs.
The root cause is uninitialized fields in tx_info(skb->cb) of
packet used to get garbage values. In this case if
MWIFIEX_BUF_FLAG_REQUEUED_PKT flag is mistakenly set, txpd
header was skipped. This patch makes sure that tx_info is
correctly initialized to fix the problem.
Reported-by: Andrew Wiley <wiley.andrew.j@gmail.com>
Reported-by: Linus Gasser <list@markas-al-nour.org>
Reported-by: Michael Hirsch <hirsch@teufel.de>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 391acf970d21219a2a5446282d3b20eace0c0d7a upstream.
When runing with the kernel(3.15-rc7+), the follow bug occurs:
[ 9969.258987] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:586
[ 9969.359906] in_atomic(): 1, irqs_disabled(): 0, pid: 160655, name: python
[ 9969.441175] INFO: lockdep is turned off.
[ 9969.488184] CPU: 26 PID: 160655 Comm: python Tainted: G A 3.15.0-rc7+ #85
[ 9969.581032] Hardware name: FUJITSU-SV PRIMEQUEST 1800E/SB, BIOS PRIMEQUEST 1000 Series BIOS Version 1.39 11/16/2012
[ 9969.706052] ffffffff81a20e60 ffff8803e941fbd0 ffffffff8162f523 ffff8803e941fd18
[ 9969.795323] ffff8803e941fbe0 ffffffff8109995a ffff8803e941fc58 ffffffff81633e6c
[ 9969.884710] ffffffff811ba5dc ffff880405c6b480 ffff88041fdd90a0 0000000000002000
[ 9969.974071] Call Trace:
[ 9970.003403] [<ffffffff8162f523>] dump_stack+0x4d/0x66
[ 9970.065074] [<ffffffff8109995a>] __might_sleep+0xfa/0x130
[ 9970.130743] [<ffffffff81633e6c>] mutex_lock_nested+0x3c/0x4f0
[ 9970.200638] [<ffffffff811ba5dc>] ? kmem_cache_alloc+0x1bc/0x210
[ 9970.272610] [<ffffffff81105807>] cpuset_mems_allowed+0x27/0x140
[ 9970.344584] [<ffffffff811b1303>] ? __mpol_dup+0x63/0x150
[ 9970.409282] [<ffffffff811b1385>] __mpol_dup+0xe5/0x150
[ 9970.471897] [<ffffffff811b1303>] ? __mpol_dup+0x63/0x150
[ 9970.536585] [<ffffffff81068c86>] ? copy_process.part.23+0x606/0x1d40
[ 9970.613763] [<ffffffff810bf28d>] ? trace_hardirqs_on+0xd/0x10
[ 9970.683660] [<ffffffff810ddddf>] ? monotonic_to_bootbased+0x2f/0x50
[ 9970.759795] [<ffffffff81068cf0>] copy_process.part.23+0x670/0x1d40
[ 9970.834885] [<ffffffff8106a598>] do_fork+0xd8/0x380
[ 9970.894375] [<ffffffff81110e4c>] ? __audit_syscall_entry+0x9c/0xf0
[ 9970.969470] [<ffffffff8106a8c6>] SyS_clone+0x16/0x20
[ 9971.030011] [<ffffffff81642009>] stub_clone+0x69/0x90
[ 9971.091573] [<ffffffff81641c29>] ? system_call_fastpath+0x16/0x1b
The cause is that cpuset_mems_allowed() try to take
mutex_lock(&callback_mutex) under the rcu_read_lock(which was hold in
__mpol_dup()). And in cpuset_mems_allowed(), the access to cpuset is
under rcu_read_lock, so in __mpol_dup, we can reduce the rcu_read_lock
protection region to protect the access to cpuset only in
current_cpuset_is_being_rebound(). So that we can avoid this bug.
This patch is a temporary solution that just addresses the bug
mentioned above, can not fix the long-standing issue about cpuset.mems
rebinding on fork():
"When the forker's task_struct is duplicated (which includes
->mems_allowed) and it races with an update to cpuset_being_rebound
in update_tasks_nodemask() then the task's mems_allowed doesn't get
updated. And the child task's mems_allowed can be wrong if the
cpuset's nodemask changes before the child has been added to the
cgroup's tasklist."
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 7114aae02742d6b5c5a0d39a41deb61d415d3717 upstream.
Add a memory barrier prior to sending a new command to the VIOS
to ensure the VIOS does not receive stale data in the command buffer.
Also add a memory barrier when processing the CRQ for completed commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[bwh: Backported to 3.2: as the iSeries code is still present, these
functions have different names and live in rpa_vscsi.c.]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 9ee755974bea2f9880e517ec985dc9dede1b3a36 upstream.
If a CRQ reset is triggered for some reason while in the middle
of performing VSCSI adapter initialization, we don't want to
call the done function for the initialization MAD commands as
this will only result in two threads attempting initialization
at the same time, resulting in failures.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d6236f6d1d885aa19d1cd7317346fe795227a3cc upstream.
The system suspend flow as following:
1, Freeze all user processes and kenrel threads.
2, Try to suspend all devices.
2.1, If pci device is in RPM suspended state, then pci driver will try
to resume it to RPM active state in the prepare stage.
2.2, xhci_resume function calls usb_hcd_resume_root_hub to queue two
workqueue items to resume usb2&usb3 roothub devices.
2.3, Call suspend callbacks of devices.
2.3.1, All suspend callbacks of all hcd's children, including
roothub devices are called.
2.3.2, Finally, hcd_pci_suspend callback is called.
Due to workqueue threads were already frozen in step 1, the workqueue
items can't be scheduled, and the roothub devices can't be resumed in
this flow. The HCD_FLAG_WAKEUP_PENDING flag which is set in
usb_hcd_resume_root_hub won't be cleared. Finally,
hcd_pci_suspend will return -EBUSY, and system suspend fails.
The reason why this issue doesn't show up very often is due to that
choose_wakeup will be called in step 2.3.1. In step 2.3.1, if
udev->do_remote_wakeup is not equal to device_may_wakeup(&udev->dev), then
udev will resume to RPM active for changing the wakeup settings. This
has been a lucky hit which hides this issue.
For some special xHCI controllers which have no USB2 port, then roothub
will not match hub driver due to probe failed. Then its
do_remote_wakeup will be set to zero, and we won't be as lucky.
xhci driver doesn't need to resume roothub devices everytime like in
the above case. It's only needed when there are pending event TRBs.
This patch should be back-ported to kernels as old as 3.2, that
contains the commit f69e3120df82391a0ee8118e0a156239a06b2afb
"USB: XHCI: resume root hubs when the controller resumes"
Signed-off-by: Wang, Yu <yu.y.wang@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[use readl() instead of removed xhci_readl(), reword commit message -Mathias]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ff8cbf250b448aac35589f6075082c3fcad8a8fe upstream.
When xHCI PCI host is suspended, if do_wakeup is false in xhci_pci_suspend,
xhci_bus_suspend needs to clear all root port wake on bits. Otherwise some Intel
platforms may get a spurious wakeup, even if PCI PME# is disabled.
This patch should be back-ported to kernels as old as 2.6.37, that
contains the commit 9777e3ce907d4cb5a513902a87ecd03b52499569
"USB: xHCI: bus power management implementation".
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 3213b151387df0b95f4eada104f68eb1c1409cb3 upstream.
The transfer burst count (TBC) field in xhci 1.0 hosts should be set
to the number of bursts needed to transfer all packets in a isoc TD.
Supported values are 0-2 (1 to 3 bursts per service interval).
Formula for TBC calculation is given in xhci spec section 4.11.2.3:
TBC = roundup( Transfer Descriptor Packet Count / Max Burst Size +1 ) - 1
This patch should be applied to stable kernels since 3.0 that contain
the commit 5cd43e33b9519143f06f507dd7cbee6b7a621885
"xhci 1.0: Set transfer burst count field."
Suggested-by: ShiChun Ma <masc2008@qq.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b0ebef36e93703e59003ad6a1a20227e47714417 upstream.
Adding a couple of Olivetti modems and blacklisting the net
function on a couple which are already supported.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit aea1ae8760314e072bf1b773521e9de5d5dda10d upstream.
Fix NULL-pointer dereference when probing an interface with no
endpoints.
These devices have two bulk endpoints per interface, but this avoids
crashing the kernel if a user forces a non-FTDI device to be probed.
Note that the iterator variable was made unsigned in order to avoid
a maybe-uninitialized compiler warning for ep_desc after the loop.
Fixes: 895f28badce9 ("USB: ftdi_sio: fix hi-speed device packet size
calculation")
Reported-by: Mike Remski <mremski@mutualink.net>
Tested-by: Mike Remski <mremski@mutualink.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit f0688c8b81d2ea239c3fb0b848f623b579238d99 upstream.
If the descriptors do not need any strings and user space sends empty
set of strings, the ffs->stringtabs field remains NULL. Thus
*ffs->stringtabs in functionfs_bind leads to a NULL pointer
dereferenece.
The bug was introduced by commit [fd7c9a007f: “use usb_string_ids_n()”].
While at it, remove double initialisation of lang local variable in
that function.
ffs->strings_count does not need to be checked in any way since in
the above scenario it will remain zero and usb_string_ids_n() is
a no-operation when colled with 0 argument.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 7cb060a91c0efc5ff94f83c6df3ed705e143cdb9 upstream.
KVM does not really do much with the PAT, so this went unnoticed for a
long time. It is exposed however if you try to do rdmsr on the PAT
register.
Reported-by: Valentine Sinitsyn <valentine.sinitsyn@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 682367c494869008eb89ef733f196e99415ae862 upstream.
Recent Intel CPUs have 10 variable range MTRRs. Since operating systems
sometime make assumptions on CPUs while they ignore capability MSRs, it is
better for KVM to be consistent with recent CPUs. Reporting more MTRRs than
actually supported has no functional implications.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c021f241f4fab2bb4fc4120a38a828a03dd3f970 upstream.
Fix a parser-bug in the omap2 muxing code where muxtable-entries will be
wrongly selected if the requested muxname is a *prefix* of their
m0-entry and they have a matching mN-entry. Fix by additionally checking
that the length of the m0_entry is equal.
For example muxing of "dss_data2.dss_data2" on omap32xx will fail
because the prefix "dss_data2" will match the mux-entries "dss_data2" as
well as "dss_data20", with the suffix "dss_data2" matching m0 (for
dss_data2) and m4 (for dss_data20). Thus both are recognized as signal
path candidates:
Relevant muxentries from mux34xx.c:
_OMAP3_MUXENTRY(DSS_DATA20, 90,
"dss_data20", NULL, "mcspi3_somi", "dss_data2",
"gpio_90", NULL, NULL, "safe_mode"),
_OMAP3_MUXENTRY(DSS_DATA2, 72,
"dss_data2", NULL, NULL, NULL,
"gpio_72", NULL, NULL, "safe_mode"),
This will result in a failure to mux the pin at all:
_omap_mux_get_by_name: Multiple signal paths (2) for dss_data2.dss_data2
Patch should apply to linus' latest master down to rather old linux-2.6
trees.
Signed-off-by: David R. Piegdon <lkml@p23q.org>
[tony@atomide.com: updated description to include full description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
This reverts commit caa5344994778a2b4725b2d75c74430f76925e4a, which
was commit fe6cc55f3a9a053482a76f5a6b2257cee51b4663 upstream. In 3.2,
the transport header length is not calculated in the forwarding path,
so skb_gso_network_seglen() returns an incorrect result. We also have
problems due to the local_df flag not being set correctly.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
This reverts commit 59d9f389df3cdf72833d5ee17c3fe959b6bdc792, which
was commit ca6c5d4ad216d5942ae544bbf02503041bd802aa upstream. It is a
valid fix, but depends on sk_buff::local_df being set in all the right
cases, which it wasn't in 3.2. We need to defer it unless and until
the other fixes are also backported to 3.2.y.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
|
|
commit 1fd819ecb90cc9b822cd84d3056ddba315d3340f upstream.
skb_segment copies frags around, so we need
to copy them carefully to avoid accessing
user memory after reporting completion to userspace
through a callback.
skb_segment doesn't normally happen on datapath:
TSO needs to be disabled - so disabling zero copy
in this case does not look like a big deal.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2. As skb_segment() only supports page-frags *or* a
frag list, there is no need for the additional frag_skb pointer or the
preparatory renaming.]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit dcc0fb782b3a6e2abfeaaeb45dd88ed09596be0f upstream.
Export skb_copy_ubufs so that modules can orphan frags.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit a353e0ce0fd42d8859260666d1e9b10f2abd4698 upstream.
Many places do
if ((skb_shinfo(skb)->tx_flags & SKBTX_DEV_ZEROCOPY))
skb_copy_ubufs(skb, gfp_mask);
to copy and invoke frag destructors if necessary.
Add an inline helper for this.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b9cd18de4db3c9ffa7e17b0dc0ca99ed5aa4d43a upstream.
The 'sysret' fastpath does not correctly restore even all regular
registers, much less any segment registers or reflags values. That is
very much part of why it's faster than 'iret'.
Normally that isn't a problem, because the normal ptrace() interface
catches the process using the signal handler infrastructure, which
always returns with an iret.
However, some paths can get caught using ptrace_event() instead of the
signal path, and for those we need to make sure that we aren't going to
return to user space using 'sysret'. Otherwise the modifications that
may have been done to the register set by the tracer wouldn't
necessarily take effect.
Fix it by forcing IRET path by setting TIF_NOTIFY_RESUME from
arch_ptrace_stop_needed() which is invoked from ptrace_stop().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
