Age | Commit message (Collapse) | Author |
|
|
|
commit 8bfae4f9938b6c1f033a5159febe97e441d6d526 upstream.
Sometimes while CPU have some load and ath5k doing the wireless
interface reset the whole WiSoC completely freezes. Set of tests shows
that using atomic delay function while we wait interface reset helps to
avoid such freezes.
The easiest way to reproduce this issue: create a station interface,
start continous scan with wpa_supplicant and load CPU by something. Or
just create multiple station interfaces and put them all in continous
scan.
This patch partially reverts the commit 1846ac3dbec0 ("ath5k: Use
usleep_range where possible"), which replaces initial udelay()
by usleep_range().
I do not know actual source of this issue, but all looks like that HW
freeze is caused by transaction on internal SoC bus, while wireless
block is in reset state.
Also I should note that I do not know how many chips are affected, but I
did not see this issue with chips, other than AR5312.
CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Fixes: 1846ac3dbec0 ("ath5k: Use usleep_range where possible")
Reported-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Eric Bree <ebree@nltinc.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6e17cb12881ba8d5e456b89f072dc6b70048af36 upstream.
i915.ko depends upon the acpi/video.ko module and so refuses to load if
ACPI is disabled at runtime if for example the BIOS is broken beyond
repair. acpi/video provides an optional service for i915.ko and so we
should just allow the modules to load, but do no nothing in order to let
the machines boot correctly.
Reported-by: Bill Augur <bill-auger@programmer.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Acked-by: Aaron Lu <aaron.lu@intel.com>
[ rjw: Fixed up the new comment in acpi_video_init() ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dbfb00c3e7e18439f2ebf67fe99bf7a50b5bae1e upstream.
The logic was reversed from what the hw actually exposed.
Fixes graphics corruption in certain harvest configurations.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
unregistered
commit 84672369ffb98a51d4ddf74c20a23636da3ad615 upstream.
Whenever a device is unregistered in vmbus_device_unregister (drivers/hv/vmbus_drv.c), the device name in the log message may contain garbage as the memory has already been freed by the time pr_info is called. Log example:
[ 3149.170475] hv_vmbus: child device àõsèè0_5 unregistered
By logging the message just before calling device_unregister, the correct device name is printed:
[ 3145.034652] hv_vmbus: child device vmbus_0_5 unregistered
Also changing register & unregister messages to debug to avoid unnecessarily cluttering the kernel log.
Signed-off-by: Fernando M Soto <fsoto@bluecatnetworks.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8e7b341037db1835ee6eea64663013cbfcf33575 upstream.
The ignore check that got added in 6ce901eb61 ("HID: input: fix confusion
on conflicting mappings") needs to properly check for VARIABLE reports
as well (ARRAY reports should be ignored), otherwise legitimate keyboards
might break.
Fixes: 6ce901eb61 ("HID: input: fix confusion on conflicting mappings")
Reported-by: Fredrik Hallenberg <megahallon@gmail.com>
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6ce901eb61aa30ba8565c62049ee80c90728ef14 upstream.
On an PC-101/103/104 keyboard (American layout) the 'Enter' key and its
neighbours look like this:
+---+ +---+ +-------+
| 1 | | 2 | | 5 |
+---+ +---+ +-------+
+---+ +-----------+
| 3 | | 4 |
+---+ +-----------+
On a PC-102/105 keyboard (European layout) it looks like this:
+---+ +---+ +-------+
| 1 | | 2 | | |
+---+ +---+ +-+ 4 |
+---+ +---+ | |
| 3 | | 5 | | |
+---+ +---+ +-----+
(Note that the number of keys is the same, but key '5' is moved down and
the shape of key '4' is changed. Keys '1' to '3' are exactly the same.)
The keys 1-4 report the same scan-code in HID in both layouts, even though
the keysym they produce is usually different depending on the XKB-keymap
used by user-space.
However, key '5' (US 'backslash'/'pipe') reports 0x31 for the upper layout
and 0x32 for the lower layout, as defined by the HID spec. This is highly
confusing as the linux-input API uses a single keycode for both.
So far, this was never a problem as there never has been a keyboard with
both of those keys present at the same time. It would have to look
something like this:
+---+ +---+ +-------+
| 1 | | 2 | | x31 |
+---+ +---+ +-------+
+---+ +---+ +-----+
| 3 | |x32| | 4 |
+---+ +---+ +-----+
HID can represent such a keyboard, but the linux-input API cannot.
Furthermore, any user-space mapping would be confused by this and,
luckily, no-one ever produced such hardware.
Now, the HID input layer fixed this mess by mapping both 0x31 and 0x32 to
the same keycode (KEY_BACKSLASH==0x2b). As only one of both physical keys
is present on a hardware, this works just fine.
Lets introduce hardware-vendors into this:
------------------------------------------
Unfortunately, it seems way to expensive to produce a different device for
American and European layouts. Therefore, hardware-vendors put both keys,
(0x31 and 0x32) on the same keyboard, but only one of them is hooked up
to the physical button, the other one is 'dead'.
This means, they can use the same hardware, with a different button-layout
and automatically produce the correct HID events for American *and*
European layouts. This is unproblematic for normal keyboards, as the
'dead' key will never report any KEY-DOWN events. But RollOver keyboards
send the whole matrix on each key-event, allowing n-key roll-over mode.
This means, we get a 0x31 and 0x32 event on each key-press. One of them
will always be 0, the other reports the real state. As we map both to the
same keycode, we will get spurious key-events, even though the real
key-state never changed.
The easiest way would be to blacklist 'dead' keys and never handle those.
We could simply read the 'country' tag of USB devices and blacklist either
key according to the layout. But... hardware vendors... want the same
device for all countries and thus many of them set 'country' to 0 for all
devices. Meh..
So we have to deal with this properly. As we cannot know which of the keys
is 'dead', we either need a heuristic and track those keys, or we simply
make use of our value-tracking for HID fields. We simply ignore HID events
for absolute data if the data didn't change. As HID tracks events on the
HID level, we haven't done the keycode translation, yet. Therefore, the
'dead' key is tracked independently of the real key, therefore, any events
on it will be ignored.
This patch simply discards any HID events for absolute data if it didn't
change compared to the last report. We need to ignore relative and
buffered-byte reports for obvious reasons. But those cannot be affected by
this bug, so we're fine.
Preferably, we'd do this filtering on the HID-core level. But this might
break a lot of custom drivers, if they do not follow the HID specs.
Therefore, we do this late in hid-input just before we inject it into the
input layer (which does the exact same filtering, but on the keycode
level).
If this turns out to break some devices, we might have to limit filtering
to EV_KEY events. But lets try to do the Right Thing first, and properly
filter any absolute data that didn't change.
This patch is tagged for 'stable' as it fixes a lot of n-key RollOver
hardware. We might wanna wait with backporting for a while, before we know
it doesn't break anything else, though.
Reported-by: Adam Goode <adam@spicenitz.org>
Reported-by: Fredrik Hallenberg <megahallon@gmail.com>
Tested-by: Fredrik Hallenberg <megahallon@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit be8e89087ec2d2c8a1ad1e3db64bf4efdfc3c298 upstream.
The hardware range code values and list of valid ranges for the AI
subdevice is incorrect for several supported boards. The hardware range
code values for all boards except PCI-DAS4020/12 is determined by
calling `ai_range_bits_6xxx()` based on the maximum voltage of the range
and whether it is bipolar or unipolar, however it only returns the
correct hardware range code for the PCI-DAS60xx boards. For
PCI-DAS6402/16 (and /12) it returns the wrong code for the unipolar
ranges. For PCI-DAS64/Mx/16 it returns the wrong code for all the
ranges and the comedi range table is incorrect.
Change `ai_range_bits_6xxx()` to use a look-up table pointed to by new
member `ai_range_codes` of `struct pcidas64_board` to map the comedi
range table indices to the hardware range codes. Use a new comedi range
table for the PCI-DAS64/Mx/16 boards (and the commented out variants).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 22aa66a3ee5b61e0f4a0bfeabcaa567861109ec3 upstream.
When the snapshot target is unloaded, snapshot_dtr() waits until
pending_exceptions_count drops to zero. Then, it destroys the snapshot.
Therefore, the function that decrements pending_exceptions_count
should not touch the snapshot structure after the decrement.
pending_complete() calls free_pending_exception(), which decrements
pending_exceptions_count, and then it performs up_write(&s->lock) and it
calls retry_origin_bios() which dereferences s->origin. These two
memory accesses to the fields of the snapshot may touch the dm_snapshot
struture after it is freed.
This patch moves the call to free_pending_exception() to the end of
pending_complete(), so that the snapshot will not be destroyed while
pending_complete() is in progress.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2bec1f4a8832e74ebbe859f176d8a9cb20dd97f4 upstream.
The function dm_get_md finds a device mapper device with a given dev_t,
increases the reference count and returns the pointer.
dm_get_md calls dm_find_md, dm_find_md takes _minor_lock, finds the
device, tests that the device doesn't have DMF_DELETING or DMF_FREEING
flag, drops _minor_lock and returns pointer to the device. dm_get_md then
calls dm_get. dm_get calls BUG if the device has the DMF_FREEING flag,
otherwise it increments the reference count.
There is a possible race condition - after dm_find_md exits and before
dm_get is called, there are no locks held, so the device may disappear or
DMF_FREEING flag may be set, which results in BUG.
To fix this bug, we need to call dm_get while we hold _minor_lock. This
patch renames dm_find_md to dm_get_md and changes it so that it calls
dm_get while holding the lock.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 37527b869207ad4c208b1e13967d69b8bba1fbf9 upstream.
I created a dm-raid1 device backed by a device that supports DISCARD
and another device that does NOT support DISCARD with the following
dm configuration:
# echo '0 2048 mirror core 1 512 2 /dev/sda 0 /dev/sdb 0' | dmsetup create moo
# lsblk -D
NAME DISC-ALN DISC-GRAN DISC-MAX DISC-ZERO
sda 0 4K 1G 0
`-moo (dm-0) 0 4K 1G 0
sdb 0 0B 0B 0
`-moo (dm-0) 0 4K 1G 0
Notice that the mirror device /dev/mapper/moo advertises DISCARD
support even though one of the mirror halves doesn't.
If I issue a DISCARD request (via fstrim, mount -o discard, or ioctl
BLKDISCARD) through the mirror, kmirrord gets stuck in an infinite
loop in do_region() when it tries to issue a DISCARD request to sdb.
The problem is that when we call do_region() against sdb, num_sectors
is set to zero because q->limits.max_discard_sectors is zero.
Therefore, "remaining" never decreases and the loop never terminates.
To fix this: before entering the loop, check for the combination of
REQ_DISCARD and no discard and return -EOPNOTSUPP to avoid hanging up
the mirror device.
This bug was found by the unfortunate coincidence of pvmove and a
discard operation in the RHEL 6.5 kernel; upstream is also affected.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f2ed51ac64611d717d1917820a01930174c2f236 upstream.
It may be possible that a device claims discard support but it rejects
discards with -EOPNOTSUPP. It happens when using loopback on ext2/ext3
filesystem driven by the ext4 driver. It may also happen if the
underlying devices are moved from one disk on another.
If discard error happens, we reject the bio with -EOPNOTSUPP, but we do
not degrade the array.
This patch fixes failed test shell/lvconvert-repair-transient.sh in the
lvm2 testsuite if the testsuite is extracted on an ext2 or ext3
filesystem and it is being driven by the ext4 driver.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 42b8ce6f55facfa101462e694d33fc6bca471138 upstream.
`do_cmd_ioctl()` in "comedi_fops.c" handles the `COMEDI_CMD` ioctl.
This returns `-EAGAIN` if it has copied a modified `struct comedi_cmd`
back to user-space. (This occurs when the low-level Comedi driver's
`do_cmdtest()` handler returns non-zero to indicate a problem with the
contents of the `struct comedi_cmd`, or when the `struct comedi_cmd` has
the `CMDF_BOGUS` flag set.)
`compat_cmd()` in "comedi_compat32.c" handles the 32-bit compatible
version of the `COMEDI_CMD` ioctl. Currently, it never copies a 32-bit
compatible version of `struct comedi_cmd` back to user-space, which is
at odds with the way the regular `COMEDI_CMD` ioctl is handled. To fix
it, change `compat_cmd()` to copy a 32-bit compatible version of the
`struct comedi_cmd` back to user-space when the main ioctl handler
returns `-EAGAIN`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a5e6c7eb5ccbb5f0d3a1dffce135f0a727f40e1 upstream.
The PLLs on newer Allwinner SoC's, such as the A31 and A23, have a
N multiplier factor that starts from 1, not 0.
This patch adds an option to the factor clk driver's config data
structures to specify the base value of N.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
gather segment boundary limit.
commit f76a610a8b4b6280eaedf48f3af9d5d74e418b66 upstream.
In reference to bug https://bugzilla.redhat.com/show_bug.cgi?id=1097141
Assert is seen with AMD cpu whenever calling pci_alloc_consistent.
[ 29.406183] ------------[ cut here ]------------
[ 29.410505] kernel BUG at lib/iommu-helper.c:13!
Signed-off-by: Minh Tran <minh.tran@emulex.com>
Fixes: 6733b39a1301b0b020bbcbf3295852e93e624cb1
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 957ed60b53b519064a54988c4e31e0087e47d091 upstream.
Each inode of nilfs2 stores a root node of a b-tree, and it turned out to
have a memory overrun issue:
Each b-tree node of nilfs2 stores a set of key-value pairs and the number
of them (in "bn_nchildren" member of nilfs_btree_node struct), as well as
a few other "bn_*" members.
Since the value of "bn_nchildren" is used for operations on the key-values
within the b-tree node, it can cause memory access overrun if a large
number is incorrectly set to "bn_nchildren".
For instance, nilfs_btree_node_lookup() function determines the range of
binary search with it, and too large "bn_nchildren" leads
nilfs_btree_node_get_key() in that function to overrun.
As for intermediate b-tree nodes, this is prevented by a sanity check
performed when each node is read from a drive, however, no sanity check
has been done for root nodes stored in inodes.
This patch fixes the issue by adding missing sanity check against b-tree
root nodes so that it's called when on-memory inodes are read from ifile,
inode metadata file.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 18c0b82a3e4501511b08d0e8676fb08ac08734a3 upstream.
This changeset removes all the code that allows the driver to write to
the EEPROM and update the recorded error counters and power on hours.
These two stats are unused and writing them exposes a timing risk
which could leave the EEPROM in a bad state preventing further normal
operation of the HCA.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3b524a683af8991b4eab4182b947c65f0ce1421b upstream.
Fix SCSI generic read() incorrectly returning success after detecting an
error.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6426460e5d87810e042962281fe3c1e8fc256162 upstream.
BIOS doesn't seem to set up pins for 5.1 and the SPDIF out, so we need
to give explicitly here.
Reported-and-tested-by: Misan Thropos <misanthropos@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 70372a7566b5e552dbe48abdac08c275081d8558 upstream.
When a PCM draining is performed to an empty stream that has been
already in PREPARED state, the current code just ignores and leaves as
it is, although the drain is supposed to set all such streams to SETUP
state. This patch covers that overlooked case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f0bf0bd07943bfde8f5ac39a32664810a379c7d3 upstream.
This problem was taken care of three times already in
* b0de59b5733d18b0d1974a060860a8b5c1b36a2e (TTY: do not update
atime/mtime on read/write),
* 37b7f3c76595e23257f61bd80b223de8658617ee (TTY: fix atime/mtime
regression), and
* b0b885657b6c8ef63a46bc9299b2a7715d19acde (tty: fix up atime/mtime
mess, take three)
But it still misses one point. As John Paul correctly points out, we
do not care about setting date. If somebody ever changes wall
time backwards (by mistake for example), tty timestamps are never
updated until the original wall time passes.
So check the absolute difference of times and if it large than "8
seconds or so", always update the time. That means we will update
immediatelly when changing time. Ergo, CAP_SYS_TIME can foul the
check, but it was always that way.
Thanks John for serving me this so nicely debugged.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: John Paul Perry <john_paul.perry@alcatel-lucent.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1711fd9addf214823b993468567cab1f8254fc51 upstream.
POLL_OUT isn't what callers of ->poll() are expecting to see; it's
actually __SI_POLL | 2 and it's a siginfo code, not a poll bitmap
bit...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Bruce Fields <bfields@fieldses.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7e0e953bb0cf649f93277ac8fb67ecbb7f7b04a9 upstream.
use_pde()/unuse_pde() in ->follow_link()/->put_link() resp.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0db59e59299f0b67450c5db21f7f316c8fb04e84 upstream.
As it is, we have debugfs_remove() racing with symlink traversals.
Supply ->evict_inode() and do freeing there - inode will remain
pinned until we are done with the symlink body.
And rip the idiocy with checking if dentry is positive right after
we'd verified debugfs_positive(), which is a stronger check...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a280962dc6e117e0e4baa668453f753579265d9 upstream.
X-Coverup: just ask spender
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 07fdfc5e9f1c966be8722e8fa927e5ea140df5ce upstream.
Fix return value in probe error path, which could end up returning
success (0) on errors. This could in turn lead to use-after-free or
double free (e.g. in port_remove) when the port device is removed.
Fixes: c706ebdfc895 ("USB: usb-serial: call port_probe and port_remove
at the right times")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 79fbf4a550ed6a22e1ae1516113e6c7fa5d56a53 upstream.
Fix overflow bug in tty_wait_until_sent on 64-bit machines, where an
infinite timeout (0) would be passed to the underlying tty-driver's
wait_until_sent-operation as a negative timeout (-1), causing it to
return immediately.
This manifests itself for example as tcdrain() returning immediately,
drivers not honouring the drain flags when setting terminal attributes,
or even dropped data on close as a requested infinite closing-wait
timeout would be ignored.
The first symptom was reported by Asier LLANO who noted that tcdrain()
returned prematurely when using the ftdi_sio usb-serial driver.
Fix this by passing 0 rather than MAX_SCHEDULE_TIMEOUT (LONG_MAX) to the
underlying tty driver.
Note that the serial-core wait_until_sent-implementation is not affected
by this bug due to a lucky chance (comparison to an unsigned maximum
timeout), and neither is the cyclades one that had an explicit check for
negative timeouts, but all other tty drivers appear to be affected.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: ZIV-Asier Llano Palacios <asier.llano@cgglobal.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f528bf4f57e43d1af4b2a5c97f09e43e0338c105 upstream.
Make sure to handle an infinite timeout (0).
Note that wait_until_sent is currently never called with a 0-timeout
argument due to a bug in tty_wait_until_sent.
Fixes: dcf010503966 ("USB: serial: add generic wait_until_sent
implementation")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2c3fbe3cf28fbd7001545a92a83b4f8acfd9fa36 upstream.
In case an infinite timeout (0) is requested, the irda wait_until_sent
implementation would use a zero poll timeout rather than the default
200ms.
Note that wait_until_sent is currently never called with a 0-timeout
argument due to a bug in tty_wait_until_sent.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 45ba2154d12fc43b70312198ec47085f10be801a upstream.
When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.
The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.
This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.
This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control
endpoint.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6596a926b0b6c80b730a1dd2fa91908e0a539c37 upstream.
Include the high order bit fields for Max scratchpad buffers when
calculating how many scratchpad buffers are needed.
I'm suprised this hasn't caused more issues, we never allocated more than
32 buffers even if xhci needed more. Either we got lucky and xhci never
really used past that area, or then we got enough zeroed dma memory anyway.
Should be backported as far back as possible
Reported-by: Tim Chen <tim.c.chen@linux.intel.com>
Tested-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c7d373c3f0da2b2b78c4b1ce5ae41485b3ef848c upstream.
This patch integrates Cyber Cortex AV boards with the existing
ftdi_jtag_quirk in order to use serial port 0 with JTAG which is
required by the manufacturers' software.
Steps: 2
[ftdi_sio_ids.h]
1. Defined the device PID
[ftdi_sio.c]
2. Added a macro declaration to the ids array, in order to enable the
jtag quirk for the device.
Signed-off-by: Max Mansfield <max.m.mansfield@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f0c2b68198589249afd2b1f2c4e8de8c03e19c16 upstream.
When a signal is delivered, the information in the siginfo structure
is copied to userspace. Good security practice dicatates that the
unused fields in this structure should be initialized to 0 so that
random kernel stack data isn't exposed to the user. This patch adds
such an initialization to the two places where usbfs raises signals.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dave Mielke <dave@mielke.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 675af70856d7cc026be8b6ea7a8b9db10b8b38a1 upstream.
These device ID's are not associated with the cp210x module currently,
but should be. This patch allows the devices to operate upon connecting
them to the usb bus as intended.
Signed-off-by: Michiel van de Garde <mgparser@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b3cffac04eca9af46e1e23560a8ee22b1bd36d43 upstream.
Currently the guest exit trace event saves the VCPU pointer to the
structure, and the guest PC is retrieved by dereferencing it when the
event is printed rather than directly from the trace record. This isn't
safe as the printing may occur long afterwards, after the PC has changed
and potentially after the VCPU has been freed. Usually this results in
the same (wrong) PC being printed for multiple trace events. It also
isn't portable as userland has no way to access the VCPU data structure
when interpreting the trace record itself.
Lets save the actual PC in the structure so that the correct value is
accessible later.
Fixes: 669e846e6c4e ("KVM/MIPS32: MIPS arch specific APIs for KVM")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4ff6f8e61eb7f96d3ca535c6d240f863ccd6fb7d upstream.
This has been broken for a long time: it broke first in 2.6.35, then was
almost fixed in 2.6.36 but this one-liner slipped through the cracks.
The bug shows up as an infinite loop in Windows 7 (and newer) boot on
32-bit hosts without EPT.
Windows uses CMPXCHG8B to write to page tables, which causes a
page fault if running without EPT; the emulator is then called from
kvm_mmu_page_fault. The loop then happens if the higher 4 bytes are
not 0; the common case for this is that the NX bit (bit 63) is 1.
Fixes: 6550e1f165f384f3a46b60a1be9aba4bc3c2adad
Fixes: 16518d5ada690643453eb0aef3cc7841d3623c2d
Reported-by: Erik Rull <erik.rull@rdsoftware.de>
Tested-by: Erik Rull <erik.rull@rdsoftware.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd9ef135e3542ffc621c4eb7f0091870ec7a1504 upstream.
Improper arithmetics when calculting the address of the extended ref could
lead to an out of bounds memory read and kernel panic.
Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a8b36f378060d20062a0918e99fae39ff077bf0 upstream.
When using the fast file fsync code path we can miss the fact that new
writes happened since the last file fsync and therefore return without
waiting for the IO to finish and write the new extents to the fsync log.
Here's an example scenario where the fsync will miss the fact that new
file data exists that wasn't yet durably persisted:
1. fs_info->last_trans_committed == N - 1 and current transaction is
transaction N (fs_info->generation == N);
2. do a buffered write;
3. fsync our inode, this clears our inode's full sync flag, starts
an ordered extent and waits for it to complete - when it completes
at btrfs_finish_ordered_io(), the inode's last_trans is set to the
value N (via btrfs_update_inode_fallback -> btrfs_update_inode ->
btrfs_set_inode_last_trans);
4. transaction N is committed, so fs_info->last_trans_committed is now
set to the value N and fs_info->generation remains with the value N;
5. do another buffered write, when this happens btrfs_file_write_iter
sets our inode's last_trans to the value N + 1 (that is
fs_info->generation + 1 == N + 1);
6. transaction N + 1 is started and fs_info->generation now has the
value N + 1;
7. transaction N + 1 is committed, so fs_info->last_trans_committed
is set to the value N + 1;
8. fsync our inode - because it doesn't have the full sync flag set,
we only start the ordered extent, we don't wait for it to complete
(only in a later phase) therefore its last_trans field has the
value N + 1 set previously by btrfs_file_write_iter(), and so we
have:
inode->last_trans <= fs_info->last_trans_committed
(N + 1) (N + 1)
Which made us not log the last buffered write and exit the fsync
handler immediately, returning success (0) to user space and resulting
in data loss after a crash.
This can actually be triggered deterministically and the following excerpt
from a testcase I made for xfstests triggers the issue. It moves a dummy
file across directories and then fsyncs the old parent directory - this
is just to trigger a transaction commit, so moving files around isn't
directly related to the issue but it was chosen because running 'sync' for
example does more than just committing the current transaction, as it
flushes/waits for all file data to be persisted. The issue can also happen
at random periods, since the transaction kthread periodicaly commits the
current transaction (about every 30 seconds by default).
The body of the test is:
_scratch_mkfs >> $seqres.full 2>&1
_init_flakey
_mount_flakey
# Create our main test file 'foo', the one we check for data loss.
# By doing an fsync against our file, it makes btrfs clear the 'needs_full_sync'
# bit from its flags (btrfs inode specific flags).
$XFS_IO_PROG -f -c "pwrite -S 0xaa 0 8K" \
-c "fsync" $SCRATCH_MNT/foo | _filter_xfs_io
# Now create one other file and 2 directories. We will move this second file
# from one directory to the other later because it forces btrfs to commit its
# currently open transaction if we fsync the old parent directory. This is
# necessary to trigger the data loss bug that affected btrfs.
mkdir $SCRATCH_MNT/testdir_1
touch $SCRATCH_MNT/testdir_1/bar
mkdir $SCRATCH_MNT/testdir_2
# Make sure everything is durably persisted.
sync
# Write more 8Kb of data to our file.
$XFS_IO_PROG -c "pwrite -S 0xbb 8K 8K" $SCRATCH_MNT/foo | _filter_xfs_io
# Move our 'bar' file into a new directory.
mv $SCRATCH_MNT/testdir_1/bar $SCRATCH_MNT/testdir_2/bar
# Fsync our first directory. Because it had a file moved into some other
# directory, this made btrfs commit the currently open transaction. This is
# a condition necessary to trigger the data loss bug.
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/testdir_1
# Now fsync our main test file. If the fsync succeeds, we expect the 8Kb of
# data we wrote previously to be persisted and available if a crash happens.
# This did not happen with btrfs, because of the transaction commit that
# happened when we fsynced the parent directory.
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foo
# Simulate a crash/power loss.
_load_flakey_table $FLAKEY_DROP_WRITES
_unmount_flakey
_load_flakey_table $FLAKEY_ALLOW_WRITES
_mount_flakey
# Now check that all data we wrote before are available.
echo "File content after log replay:"
od -t x1 $SCRATCH_MNT/foo
status=0
exit
The expected golden output for the test, which is what we get with this
fix applied (or when running against ext3/4 and xfs), is:
wrote 8192/8192 bytes at offset 0
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
wrote 8192/8192 bytes at offset 8192
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
File content after log replay:
0000000 aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
*
0020000 bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb
*
0040000
Without this fix applied, the output shows the test file does not have
the second 8Kb extent that we successfully fsynced:
wrote 8192/8192 bytes at offset 0
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
wrote 8192/8192 bytes at offset 8192
XXX Bytes, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
File content after log replay:
0000000 aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
*
0020000
So fix this by skipping the fsync only if we're doing a full sync and
if the inode's last_trans is <= fs_info->last_trans_committed, or if
the inode is already in the log. Also remove setting the inode's
last_trans in btrfs_file_write_iter since it's useless/unreliable.
Also because btrfs_file_write_iter no longer sets inode->last_trans to
fs_info->generation + 1, don't set last_trans to 0 if we bail out and don't
bail out if last_trans is 0, otherwise something as simple as the following
example wouldn't log the second write on the last fsync:
1. write to file
2. fsync file
3. fsync file
|--> btrfs_inode_in_log() returns true and it set last_trans to 0
4. write to file
|--> btrfs_file_write_iter() no longers sets last_trans, so it
remained with a value of 0
5. fsync
|--> inode->last_trans == 0, so it bails out without logging the
second write
A test case for xfstests will be sent soon.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1932b7be973b554ffe20a5bba6ffaed6fa995cdc upstream.
A block-local variable stores error code but btrfs_get_blocks_direct may
not return it in the end as there's a ret defined in the function scope.
Fixes: d187663ef24c ("Btrfs: lock extents as we map them in DIO")
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 19e353f2b344ad86cea6ebbc0002e5f903480a90 upstream.
The intention is obviously to sign-extend a 12 bit quantity. But
because of C's promotion rules, the assignment is equivalent to "val16
&= 0xfff;". Use the proper API for this.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 956421fbb74c3a6261903f3836c0740187cf038b upstream.
'ret_from_fork' checks TIF_IA32 to determine whether 'pt_regs' and
the related state make sense for 'ret_from_sys_call'. This is
entirely the wrong check. TS_COMPAT would make a little more
sense, but there's really no point in keeping this optimization
at all.
This fixes a return to the wrong user CS if we came from int
0x80 in a 64-bit task.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/4710be56d76ef994ddf59087aad98c000fbab9a4.1424989793.git.luto@amacapital.net
[ Backported from tip:x86/asm. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In 3.10.y backport patch 1dba303727f52ea062580b0a9b3f0c3b462769cf,
the logic to call pm_qos_update_target was moved to __pm_qos_update_request.
However, the original code was left in function pm_qos_update_request.
Currently, if pm_qos_update_request is called where new_value !=
req->node.prio then pm_qos_update_target will be called twice in a row.
Once in pm_qos_update_request and then again in the following call to
_pm_qos_update_request.
Removing the left over code from pm_qos_update_request stops this second
call to pm_qos_update_target where the work of removing / re-adding the
new_value in the constraints list would be duplicated.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa179935edea9a64dec4b757090c8106a3907ffa upstream.
This patch adds a check to sbc_parse_cdb() in order to detect when
an LBA + sector vs. end-of-device calculation wraps when the LBA is
sufficently large enough (eg: 0xFFFFFFFFFFFFFFFF).
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9cb12d7b4ccaa976f97ce0c5fd0f1b6a83bc2a75 upstream.
For whatever reason, generic_access_phys() only remaps one page, but
actually allows to access arbitrary size. It's quite easy to trigger
large reads, like printing out large structure with gdb, which leads to a
crash. Fix it by remapping correct size.
Fixes: 28b2ee20c7cb ("access_process_vm device memory infrastructure")
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 372549c2a3778fd3df445819811c944ad54609ca upstream.
What we want to check here is whether there is highorder freepage in buddy
list of other migratetype in order to steal it without fragmentation.
But, current code just checks cc->order which means allocation request
order. So, this is wrong.
Without this fix, non-movable synchronous compaction below pageblock order
would not stopped until compaction is complete, because migratetype of
most pageblocks are movable and high order freepage made by compaction is
usually on movable type buddy list.
There is some report related to this bug. See below link.
http://www.spinics.net/lists/linux-mm/msg81666.html
Although the issued system still has load spike comes from compaction,
this makes that system completely stable and responsive according to his
report.
stress-highalloc test in mmtests with non movable order 7 allocation
doesn't show any notable difference in allocation success rate, but, it
shows more compaction success rate.
Compaction success rate (Compaction success * 100 / Compaction stalls, %)
18.47 : 28.94
Fixes: 1fb3f8ca0e92 ("mm: compaction: capture a suitable high-order page immediately when it is made available")
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8138a67a5557ffea3a21dfd6f037842d4e748513 upstream.
I noticed that "allowed" can easily overflow by falling below 0, because
(total_vm / 32) can be larger than "allowed". The problem occurs in
OVERCOMMIT_NONE mode.
In this case, a huge allocation can success and overcommit the system
(despite OVERCOMMIT_NONE mode). All subsequent allocations will fall
(system-wide), so system become unusable.
The problem was masked out by commit c9b1d0981fcc
("mm: limit growth of 3% hardcoded other user reserve"),
but it's easy to reproduce it on older kernels:
1) set overcommit_memory sysctl to 2
2) mmap() large file multiple times (with VM_SHARED flag)
3) try to malloc() large amount of memory
It also can be reproduced on newer kernels, but miss-configured
sysctl_user_reserve_kbytes is required.
Fix this issue by switching to signed arithmetic here.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Cc: Andrew Shewmaker <agshew@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5703b087dc8eaf47bfb399d6cf512d471beff405 upstream.
I noticed, that "allowed" can easily overflow by falling below 0,
because (total_vm / 32) can be larger than "allowed". The problem
occurs in OVERCOMMIT_NONE mode.
In this case, a huge allocation can success and overcommit the system
(despite OVERCOMMIT_NONE mode). All subsequent allocations will fall
(system-wide), so system become unusable.
The problem was masked out by commit c9b1d0981fcc
("mm: limit growth of 3% hardcoded other user reserve"),
but it's easy to reproduce it on older kernels:
1) set overcommit_memory sysctl to 2
2) mmap() large file multiple times (with VM_SHARED flag)
3) try to malloc() large amount of memory
It also can be reproduced on newer kernels, but miss-configured
sysctl_user_reserve_kbytes is required.
Fix this issue by switching to signed arithmetic here.
[akpm@linux-foundation.org: use min_t]
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Cc: Andrew Shewmaker <agshew@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9fbc1f635fd0bd28cb32550211bf095753ac637a upstream.
If __unmap_hugepage_range() tries to unmap the address range over which
hugepage migration is on the way, we get the wrong page because pte_page()
doesn't work for migration entries. This patch simply clears the pte for
migration entries as we do for hwpoison entries.
Fixes: 290408d4a2 ("hugetlb: hugepage migration core")
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9215f437b85da339a7dfe3db6e288637406f88b2 ]
Currently the list is traversed using rcu variant. That is not correct
since dev_set_mac_address can be called which eventually calls
rtmsg_ifinfo_build_skb and there, skb allocation can sleep. So fix this
by remove the rcu usage here.
Fixes: 3d249d4ca7 "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit acf8dd0a9d0b9e4cdb597c2f74802f79c699e802 ]
If an over-MTU UDP datagram is sent through a SOCK_RAW socket to a
UFO-capable device, ip_ufo_append_data() sets skb->ip_summed to
CHECKSUM_PARTIAL unconditionally as all GSO code assumes transport layer
checksum is to be computed on segmentation. However, in this case,
skb->csum_start and skb->csum_offset are never set as raw socket
transmit path bypasses udp_send_skb() where they are usually set. As a
result, driver may access invalid memory when trying to calculate the
checksum and store the result (as observed in virtio_net driver).
Moreover, the very idea of modifying the userspace provided UDP header
is IMHO against raw socket semantics (I wasn't able to find a document
clearly stating this or the opposite, though). And while allowing
CHECKSUM_NONE in the UFO case would be more efficient, it would be a bit
too intrusive change just to handle a corner case like this. Therefore
disallowing UFO for packets from SOCK_DGRAM seems to be the best option.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|