| Age | Commit message (Collapse) | Author |
|---|
|
|
|
I added a failure check in patch "sbp2: variable status FIFO address
(fix login timeout)" --- alas for a wrong error value. This is a bug
since Linux 2.6.16. Leads to NULL pointer dereference if the call
failed, and bogus failure handling if call succeeded.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
There is a firmware bug in several Apple iPods which prevents access to
these iPods under certain conditions. The disk size reported by the iPod
is one sector too big. Once access to the end of the disk is attempted,
the iPod becomes inaccessible. This problem has been known for USB iPods
for some time and has recently been discovered to exist with
FireWire/USB combo iPods too.
This patch is derived from the fix in Linux 2.6.17, commit
e9a1c52c7b19d10342226c12f170d7ab644427e2, to be applicable to 2.6.16.x
without prerequisite patches. It hard-wires a workaround for three known
affected model numbers (those of 4th generation iPod, iPod Photo, iPod
mini).
Note: This patch lacks Linux 2.6.17's ability to enable and disable the
workaround via a module parameter.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This fixes a regression from the earlier DOS fix for non canonical
IRET addresses. It broke UML.
int_ret_from_syscall already does syscall exit tracing, so
no need to do it again in the caller.
This caused problems for UML and some other special programs doing
syscall interception.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
o Start booting into the capture kernel after an Oops if system is in a
unrecoverable state. System will boot into the capture kernel, if one is
pre-loaded by the user, and capture the kernel core dump.
o One of the following conditions should be true to trigger the booting of
capture kernel.
- panic_on_oops is set.
- pid of current thread is 0
- pid of current thread is 1
- Oops happened inside interrupt context.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Currently iwlist ethX freq[uency]/channel lists all the channels the card
supported for the current region, which includes some channels can only
be used in infrastructure mode. This patch filters these channels out if
the card is currently in ad-hoc mode.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Okay, just to sum things up.
This forces libata to wait for up to 2 seconds for BUSY|DRQ to clear
on resume before continuing.
[jgarzik adds...] During testing we never saw DRQ asserted, but
nonetheless (a) this works and (b) testing for DRQ won't hurt.
Signed-off-by: Mark Lord <liml@rtr.ca>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Re-enable posted writes for status FIFO.
Besides bringing back a very minor bandwidth tweak from Linux 2.6.15.x
and older, this also fixes an interoperability regression since 2.6.16:
http://bugzilla.kernel.org/show_bug.cgi?id=6356
(sbp2: scsi_add_device failed. IEEE1394 HD is not working anymore.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Vanei Heidemann <linux@javanei.com.br>
Tested-by: Martin Putzlocher <mputzi@gmx.de> (chip type unconfirmed)
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Input: psmouse - fix new device detection logic
Reported to fix http://bugs.gentoo.org/130846
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
For a very long time, echoing 'standby' or 'mem' into /sys/power/state has
killed the machine on powerpc. This patch fixes that.
This patch adds the .valid callback to pm_ops on PowerMac so that only the
suspend to disk state can be entered. Note that just returning 0 would
suffice since the upper layers don't pass PM_SUSPEND_DISK down, but we
handle it there regardless just in case that changes.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix an infrequently encountered 'sleeping function called
from invalid context' in the cpuset hooks in __alloc_pages.
Could sleep while interrupts disabled.
The routine cpuset_zone_allowed() is called by code in
mm/page_alloc.c __alloc_pages() to determine if a zone is
allowed in the current tasks cpuset. This routine can sleep,
for certain GFP_KERNEL allocations, if the zone is on a memory
node not allowed in the current cpuset, but might be allowed
in a parent cpuset.
But we can't sleep in __alloc_pages() if in interrupt, nor
if called for a GFP_ATOMIC request (__GFP_WAIT not set in
gfp_flags).
The rule was intended to be:
Don't call cpuset_zone_allowed() if you can't sleep, unless you
pass in the __GFP_HARDWALL flag set in gfp_flag, which disables
the code that might scan up ancestor cpusets and sleep.
This rule was being violated due to a bogus change made (by myself,
pj) to __alloc_pages() as part of the November 2005 effort to
cleanup its logic.
The bogus change can be seen at:
http://linux.derkeiler.com/Mailing-Lists/Kernel/2005-11/4691.html
[PATCH 01/05] mm fix __alloc_pages cpuset ALLOC_* flags
This was first noticed on a tight memory system, in code that
was disabling interrupts and doing allocation requests with
__GFP_WAIT not set, which resulted in __might_sleep() writing
complaints to the log "Debug: sleeping function called ...",
when the code in cpuset_zone_allowed() tried to take the
callback_sem cpuset semaphore.
Special thanks to Dave Chinner, for figuring this out,
and a tip of the hat to Nick Piggin who warned me of this
back in Nov 2005, before I was ready to listen.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Currently loading the ioc3 as a module will cause the ports to be numbered
in reverse order. This mod maintains the proper order of cards for port
numbering.
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Currently loading the ioc4 as a module will cause the ports to be numbered
in reverse order. This mod maintains the proper order of cards for port
numbering.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Cc: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
|
|
It appears that sockaddr_in.sin_zero is not zeroed during
getsockopt(...SO_ORIGINAL_DST...) operation. This can lead
to an information leak (CVE-2006-1343).
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
|
|
CVE-2006-2444 - Potential remote DoS in SNMP NAT helper.
Fix memory corruption caused by snmp_trap_decode:
- When snmp_trap_decode fails before the id and address are allocated,
the pointers contain random memory, but are freed by the caller
(snmp_parse_mangle).
- When snmp_trap_decode fails after allocating just the ID, it tries
to free both address and ID, but the address pointer still contains
random memory. The caller frees both ID and random memory again.
- When snmp_trap_decode fails after allocating both, it frees both,
and the callers frees both again.
The corruption can be triggered remotely when the ip_nat_snmp_basic
module is loaded and traffic on port 161 or 162 is NATed.
Found by multiple testcases of the trap-app and trap-enc groups of the
PROTOS c06-snmpv1 testsuite.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
|
|
If SCTP receives a badly formatted HB-ACK chunk, it is possible
that we may access invalid memory and potentially have a buffer
overflow. We should really make sure that the chunk format is
what we expect, before attempting to touch the data.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
(CVE-2006-1858)
When performing bound checks during the parameter processing, we
want to use the real chunk and paramter lengths for bounds instead
of the rounded ones. This prevents us from potentially walking of
the end if the chunk length was miscalculated. We still use rounded
lengths when advancing the pointer. This was found during a
conformance test that changed the chunk length without modifying
parameters.
(Vlad noted elsewhere: the most you'd overflow is 3 bytes, so problem
is parameter dependent).
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Eric Biederman points out that we can't take the task_lock while holding
tasklist_lock for writing, because another CPU that holds the task lock
might take an interrupt that then tries to take tasklist_lock for writing.
Which would be a nasty deadlock, with one CPU spinning forever in an
interrupt handler (although admittedly you need to really work at
triggering it ;)
Since the ptrace_attach() code is special and very unusual, just make it
be extra careful, and use trylock+repeat to avoid the possible deadlock.
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This holds the task lock (and, for ptrace_attach, the tasklist_lock)
over the actual attach event, which closes a race between attacking to a
thread that is either doing a PTRACE_TRACEME or getting de-threaded.
Thanks to Oleg Nesterov for reminding me about this, and Chris Wright
for noticing a lost return value in my first version.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Currently we check PageDirty() in order to make the decision to swap out
the page. However, the dirty information may be only be contained in the
ptes pointing to the page. We need to first unmap the ptes before checking
for PageDirty(). If unmap is successful then the page count of the page
will also be decreased so that pageout() works properly.
This is a fix necessary for 2.6.17. Without this fix we may migrate dirty
pages for filesystems without migration functions. Filesystems may keep
pointers to dirty pages. Migration of dirty pages can result in the
filesystem keeping pointers to freed pages.
Unmapping is currently not be separated out from removing all the
references to a page and moving the mapping. Therefore try_to_unmap will
be called again in migrate_page() if the writeout is successful. However,
it wont do anything since the ptes are already removed.
The coming updates to the page migration code will restructure the code
so that this is no longer necessary.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Basic problem: pages of a shared memory segment can only be migrated once.
In 2.6.16 through 2.6.17-rc1, shared memory mappings do not have a
migratepage address space op. Therefore, migrate_pages() falls back to
default processing. In this path, it will try to pageout() dirty pages.
Once a shared memory page has been migrated it becomes dirty, so
migrate_pages() will try to page it out. However, because the page count
is 3 [cache + current + pte], pageout() will return PAGE_KEEP because
is_page_cache_freeable() returns false. This will abort all subsequent
migrations.
This patch adds a migratepage address space op to shared memory segments to
avoid taking the default path. We use the "migrate_page()" function
because it knows how to migrate dirty pages. This allows shared memory
segment pages to migrate, subject to other conditions such as # pte's
referencing the page [page_mapcount(page)], when requested.
I think this is safe. If we're migrating a shared memory page, then we
found the page via a page table, so it must be in memory.
Can be verified with memtoy and the shmem-mbind-test script, both
available at: http://free.linux.hp.com/~lts/Tools/
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
gather_stats() is called with a spinlock held from check_pte_range. We
cannot reschedule with a lock held.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
An earlier commit (75cf7456dd87335f574dcd53c4ae616a2ad71a11) changed an
overly-zealous PCI quirk to only poke those VIA devices that need it.
However, some PCI devices were not included in what I hope is now the full
list. Consequently we're failing to run the quirk on all machines which need
it, causing IRQ routing failures.
This should I hope correct this.
Thanks to Masoud Sharbiani <masouds@masoud.ir> for pointing this out
and testing the fix.
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Alan Cox pointed out that the VIA 'IRQ fixup' was erroneously running
on my system which has no VIA southbridge (but I do have a VIA IEEE
1394 device).
This should address that. I also changed "Via IRQ" to "VIA IRQ"
(initially I read Via as a capitalized via (by way/means of).
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
This patch corrects the order of the calls to register_chrdev() and
pcmcia_register_driver(). Now udev correctly creates userspace device
files /dev/cmmN and /dev/cmxN respectively.
Based on an earlier patch by Jan Niehusmann <jan@gondor.com>.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Don't recurse back into the driver even if the unplug threshold is met,
when the driver asks for a requeue. This is both silly from a logical
point of view (requeues typically happen due to driver/hardware
shortage), and also dangerous since we could hit an endless request_fn
-> requeue -> unplug -> request_fn loop and crash on stack overrun.
Also limit blk_run_queue() to one level of recursion, similar to how
blk_start_queue() works.
This patch fixed a real problem with SLES10 and lpfc, and it could hit
any SCSI lld that returns non-zero from it's ->queuecommand() handler.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
The OSC set and query functions do not allocate enough space for return values,
and set the output buffer length to a false, too large value. This causes the
acpi-ca code to assume that the output buffer is larger than it actually is,
and overwrite memory when copying acpi return buffers into this caller provided
buffer. In some cases this can cause kernel oops if the memory that is
overwritten is a pointer. This patch will change these calls to use a
dynamically allocated output buffer, thus allowing the acpi-ca code to decide
how much space is needed.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Check for NULL kmalloc return value before writing to it.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Acked-by: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Even with fiber cards ethtool reports that the connected port is TP,
the patch fix this.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
(CVE-2006-0039)
Solar Designer found a race condition in do_add_counters(). The beginning
of paddc is supposed to be the same as tmp which was sanity-checked
above, but it might not be the same in reality. In case the integer
overflow and/or the race condition are triggered, paddc->num_counters
might not match the allocation size for paddc. If the check below
(t->private->number != paddc->num_counters) nevertheless passes (perhaps
this requires the race condition to be triggered), IPT_ENTRY_ITERATE()
would read kernel memory beyond the allocation size, potentially causing
an oops or leaking sensitive data (e.g., passwords from host system or
from another VPS) via counter increments. This requires CAP_NET_ADMIN.
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=191698
Cc: Solar Designer <solar@openwall.com>
Cc: Kirill Korotaev <dev@sw.ru>
Cc: Patrick McHardy <kaber@trash.net>
(chrisw: rebase of Kirill's patch to 2.6.16.16)
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
We can't pass a string on the stack to request_region. As soon as we
leave the function that stack is gone and the string is lost. Let's
use the same string we identify the i2c_adapter with instead, it's
more simple, more consistent, and just works.
This is the second half of fix to bug #6445.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Do not enable the SMBus device on Asus boards if suspend is used. We do
not reenable the device on resume, leading to all sorts of undesirable
effects, the worst being a total fan failure after resume on Samsung P35
laptop.
This fixes bug #6449 at bugzilla.kernel.org.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Mentioned by Mark Armbrust somewhere on Usenet.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Cc: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Yesterday, I got the following error with 2.6.16.13 during a file copy from
a smb filesystem over a wireless link. I guess there was some error on the
wireless link, which in turn caused an error condition for the smb
filesystem.
In the log, smb_file_read reports error=4294966784 (0xfffffe00), which also
shows up in the slab dumps, and also is -ERESTARTSYS. Error code 27499
corresponds to 0x6b6b, so the rq_errno field seems to be the only one being
set after freeing the slab.
In smb_add_request (which is the only place in smbfs where I found
ERESTARTSYS), I found the following:
if (!timeleft || signal_pending(current)) {
/*
* On timeout or on interrupt we want to try and remove the
* request from the recvq/xmitq.
*/
smb_lock_server(server);
if (!(req->rq_flags & SMB_REQ_RECEIVED)) {
list_del_init(&req->rq_queue);
smb_rput(req);
}
smb_unlock_server(server);
}
[...]
if (signal_pending(current))
req->rq_errno = -ERESTARTSYS;
I guess that some codepath like smbiod_flush() caused the request to be
removed from the queue, and smb_rput(req) be called, without
SMB_REQ_RECEIVED being set. This violates an asumption made by the quoted
code.
Then, the above code calls smb_rput(req) again, the req gets freed, and
req->rq_errno = -ERESTARTSYS writes into the already freed slab. As
list_del_init doesn't cause an error if called multiple times, that does
cause the observed behaviour (freed slab with rq_errno=-ERESTARTSYS).
If this observation is correct, the following patch should fix it.
I wonder why the smb code uses list_del_init everywhere - using list_del
instead would catch such situations by poisoning the next and prev
pointers.
May 4 23:29:21 knautsch kernel: [17180085.456000] ipw2200: Firmware error detected. Restarting.
May 4 23:29:21 knautsch kernel: [17180085.456000] ipw2200: Sysfs 'error' log captured.
May 4 23:33:02 knautsch kernel: [17180306.316000] ipw2200: Firmware error detected. Restarting.
May 4 23:33:02 knautsch kernel: [17180306.316000] ipw2200: Sysfs 'error' log already exists.
May 4 23:33:02 knautsch kernel: [17180306.968000] smb_file_read: //some_file validation failed, error=4294966784
May 4 23:34:18 knautsch kernel: [17180383.256000] smb_file_read: //some_file validation failed, error=4294966784
May 4 23:34:18 knautsch kernel: [17180383.284000] SMB connection re-established (-5)
May 4 23:37:19 knautsch kernel: [17180563.956000] smb_file_read: //some_file validation failed, error=4294966784
May 4 23:40:09 knautsch kernel: [17180733.636000] smb_file_read: //some_file validation failed, error=4294966784
May 4 23:40:26 knautsch kernel: [17180750.700000] smb_file_read: //some_file validation failed, error=4294966784
May 4 23:43:02 knautsch kernel: [17180907.304000] smb_file_read: //some_file validation failed, error=4294966784
May 4 23:43:08 knautsch kernel: [17180912.324000] smb_file_read: //some_file validation failed, error=4294966784
May 4 23:43:34 knautsch kernel: [17180938.416000] smb_errno: class Unknown, code 27499 from command 0x6b
May 4 23:43:34 knautsch kernel: [17180938.416000] Slab corruption: start=c4ebe09c, len=244
May 4 23:43:34 knautsch kernel: [17180938.416000] Redzone: 0x5a2cf071/0x5a2cf071.
May 4 23:43:34 knautsch kernel: [17180938.416000] Last user: [<e087b903>](smb_rput+0x53/0x90 [smbfs])
May 4 23:43:34 knautsch kernel: [17180938.416000] 000: 6b 6b 6b 6b 6b 6b 6b 6b 6a 6b 6b 6b 6b 6b 6b 6b
May 4 23:43:34 knautsch kernel: [17180938.416000] 0f0: 00 fe ff ff
May 4 23:43:34 knautsch kernel: [17180938.416000] Next obj: start=c4ebe19c, len=244
May 4 23:43:34 knautsch kernel: [17180938.416000] Redzone: 0x5a2cf071/0x5a2cf071.
May 4 23:43:34 knautsch kernel: [17180938.416000] Last user: [<00000000>](_stext+0x3feffde0/0x30)
May 4 23:43:34 knautsch kernel: [17180938.416000] 000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
May 4 23:43:34 knautsch kernel: [17180938.416000] 010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
May 4 23:43:34 knautsch kernel: [17180938.460000] SMB connection re-established (-5)
May 4 23:43:42 knautsch kernel: [17180946.292000] ipw2200: Firmware error detected. Restarting.
May 4 23:43:42 knautsch kernel: [17180946.292000] ipw2200: Sysfs 'error' log already exists.
May 4 23:45:04 knautsch kernel: [17181028.752000] ipw2200: Firmware error detected. Restarting.
May 4 23:45:04 knautsch kernel: [17181028.752000] ipw2200: Sysfs 'error' log already exists.
May 4 23:45:05 knautsch kernel: [17181029.868000] smb_file_read: //some_file validation failed, error=4294966784
May 4 23:45:36 knautsch kernel: [17181060.984000] smb_errno: class Unknown, code 27499 from command 0x6b
May 4 23:45:36 knautsch kernel: [17181060.984000] Slab corruption: start=c4ebe09c, len=244
May 4 23:45:36 knautsch kernel: [17181060.984000] Redzone: 0x5a2cf071/0x5a2cf071.
May 4 23:45:36 knautsch kernel: [17181060.984000] Last user: [<e087b903>](smb_rput+0x53/0x90 [smbfs])
May 4 23:45:36 knautsch kernel: [17181060.984000] 000: 6b 6b 6b 6b 6b 6b 6b 6b 6a 6b 6b 6b 6b 6b 6b 6b
May 4 23:45:36 knautsch kernel: [17181060.984000] 0f0: 00 fe ff ff
May 4 23:45:36 knautsch kernel: [17181060.984000] Next obj: start=c4ebe19c, len=244
May 4 23:45:36 knautsch kernel: [17181060.984000] Redzone: 0x5a2cf071/0x5a2cf071.
May 4 23:45:36 knautsch kernel: [17181060.984000] Last user: [<00000000>](_stext+0x3feffde0/0x30)
May 4 23:45:36 knautsch kernel: [17181060.984000] 000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
May 4 23:45:36 knautsch kernel: [17181060.984000] 010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
May 4 23:45:36 knautsch kernel: [17181061.024000] SMB connection re-established (-5)
May 4 23:46:17 knautsch kernel: [17181102.132000] smb_file_read: //some_file validation failed, error=4294966784
May 4 23:47:46 knautsch kernel: [17181190.468000] smb_errno: class Unknown, code 27499 from command 0x6b
May 4 23:47:46 knautsch kernel: [17181190.468000] Slab corruption: start=c4ebe09c, len=244
May 4 23:47:46 knautsch kernel: [17181190.468000] Redzone: 0x5a2cf071/0x5a2cf071.
May 4 23:47:46 knautsch kernel: [17181190.468000] Last user: [<e087b903>](smb_rput+0x53/0x90 [smbfs])
May 4 23:47:46 knautsch kernel: [17181190.468000] 000: 6b 6b 6b 6b 6b 6b 6b 6b 6a 6b 6b 6b 6b 6b 6b 6b
May 4 23:47:46 knautsch kernel: [17181190.468000] 0f0: 00 fe ff ff
May 4 23:47:46 knautsch kernel: [17181190.468000] Next obj: start=c4ebe19c, len=244
May 4 23:47:46 knautsch kernel: [17181190.468000] Redzone: 0x5a2cf071/0x5a2cf071.
May 4 23:47:46 knautsch kernel: [17181190.468000] Last user: [<00000000>](_stext+0x3feffde0/0x30)
May 4 23:47:46 knautsch kernel: [17181190.468000] 000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
May 4 23:47:46 knautsch kernel: [17181190.468000] 010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
May 4 23:47:46 knautsch kernel: [17181190.492000] SMB connection re-established (-5)
May 4 23:49:20 knautsch kernel: [17181284.828000] smb_file_read: //some_file validation failed, error=4294966784
May 4 23:49:39 knautsch kernel: [17181303.896000] smb_file_read: //some_file validation failed, error=4294966784
Signed-off-by: Jan Niehusmann <jan@gondor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
sys_flock() currently has a race which can result in a double free in the
multi-thread case.
Thread 1 Thread 2
sys_flock(file, LOCK_EX)
sys_flock(file, LOCK_UN)
If Thread 2 removes the lock from inode->i_lock before Thread 1 tests for
list_empty(&lock->fl_link) at the end of sys_flock, then both threads will
end up calling locks_free_lock for the same lock.
Fix is to make flock_lock_file() do the same as posix_lock_file(), namely
to make a copy of the request, so that the caller can always free the lock.
This also has the side-effect of fixing up a reference problem in the
lockd handling of flock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
In kernel 2.6.16, if a mounted storage device is removed, an oops happens
because ub supplies an interface device (and kobject) to the block layer,
but neglects to pin it. And apparently, the block layer expects its users
to pin device structures.
The code in ub was broken this way for years. But the bug was exposed only
by 2.6.16 when it started to call block_uevent on close, which traverses
device structures (kobjects actually).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Fixes Rhine I cards disclosing fragments of previously transmitted frames
in new transmissions.
Before transmission, any socket buffer (skb) shorter than the ethernet
minimum length of 60 bytes was zero-padded. On Rhine I cards the data can
later be copied into an aligned transmission buffer without copying this
padding. This resulted in the transmission of the frame with the extra
bytes beyond the provided content leaking the previous contents of this
buffer on to the network.
Now zero-padding is repeated in the local aligned buffer if one is used.
Following a suggestion from the via-rhine maintainer, no attempt is made
here to avoid the duplicated effort of padding the skb if it is known that
an aligned buffer will definitely be used. This is to make the change
"obviously correct" and allow it to be applied to a stable kernel if
necessary. There is no change to the flow of control and the changes are
only to the Rhine I code path.
The patch has run on an in-service Rhine-I host without incident. Frames
shorter than 60 bytes are now correctly zero-padded when captured on a
separate host. I see no unusual stats reported by ifconfig, and no unusual
log messages.
Signed-off-by: Craig Brind <craigbrind@gmail.com>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
We should add to the counter for the rdev *after* checking if the rdev is
NULL!!!
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
|
|
It is insane to be giving lease_init() the task of freeing the lock it is
supposed to initialise, given that the lock is not guaranteed to be
allocated on the stack. This causes lockups in fcntl_setlease().
Problem diagnosed by Daniel Hokka Zakrisson <daniel@hozac.com>
Also fix a slab leak in __setlease() due to an uninitialised return value.
Problem diagnosed by Björn Steinbrink.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: Daniel Hokka Zakrisson <daniel@hozac.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cc: Björn Steinbrink <B.Steinbrink@gmx.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
|
|
DATA. (CVE-2006-2274)
There is a rare situation that causes lksctp to go into infinite recursion
and crash the system. The trigger is a packet that contains at least the
first two DATA fragments of a message bundled together. The recursion is
triggered when the user data buffer is smaller that the full data message.
The problem is that we clone the skb for every fragment in the message.
When reassembling the full message, we try to link skbs from the "first
fragment" clone using the frag_list. However, since the frag_list is shared
between two clones in this rare situation, we end up setting the frag_list
pointer of the second fragment to point to itself. This causes
sctp_skb_pull() to potentially recurse indefinitely.
Proposed solution is to make a copy of the skb when attempting to link
things using frag_list.
Signed-off-by: Vladislav Yasevich <vladsilav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
(CVE-2006-2275)
This patch fixes a deadlock situation in the receive path by allowing
temporary spillover of the receive buffer.
- If the chunk we receive has a tsn that immediately follows the ctsn,
accept it even if we run out of receive buffer space and renege data with
higher TSNs.
- Once we accept one chunk in a packet, accept all the remaining chunks
even if we run out of receive buffer space.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Mark Butler <butlerm@middle.net>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
(CVE-2006-2271)
Discard an unexpected chunk in CLOSED state rather can calling BUG().
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
(CVE-2006-2272)
Use pskb_pull() to handle incoming COOKIE_ECHO and HEARTBEAT chunks that
are received as skb's with fragment list.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
|
|
Mark Moseley reported that a chroot environment on a SMB share can be
left via "cd ..\\". Similar to CVE-2006-1863 issue with cifs, this fix
is for smbfs.
Steven French <sfrench@us.ibm.com> wrote:
Looks fine to me. This should catch the slash on lookup or equivalent,
which will be all obvious paths of interest.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
