diff options
Diffstat (limited to 'drivers/thermal/rockchip_thermal.c')
| -rw-r--r-- | drivers/thermal/rockchip_thermal.c | 74 |
1 files changed, 53 insertions, 21 deletions
diff --git a/drivers/thermal/rockchip_thermal.c b/drivers/thermal/rockchip_thermal.c index 00c12c061201..86a1ab04bf95 100644 --- a/drivers/thermal/rockchip_thermal.c +++ b/drivers/thermal/rockchip_thermal.c @@ -1,7 +1,5 @@ /* - * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd - * - * Copyright (c) 2015, Fuzhou Rockchip Electronics Co., Ltd + * Copyright (c) 2014-2016, Fuzhou Rockchip Electronics Co., Ltd * Caesar Wang <wxt@rock-chips.com> * * This program is free software; you can redistribute it and/or modify it @@ -75,7 +73,7 @@ enum adc_sort_mode { #define SOC_MAX_SENSORS 2 /** - * struct chip_tsadc_table: hold information about chip-specific differences + * struct chip_tsadc_table - hold information about chip-specific differences * @id: conversion table * @length: size of conversion table * @data_mask: mask to apply on data inputs @@ -88,6 +86,20 @@ struct chip_tsadc_table { enum adc_sort_mode mode; }; +/** + * struct rockchip_tsadc_chip - hold the private data of tsadc chip + * @chn_id[SOC_MAX_SENSORS]: the sensor id of chip correspond to the channel + * @chn_num: the channel number of tsadc chip + * @tshut_temp: the hardware-controlled shutdown temperature value + * @tshut_mode: the hardware-controlled shutdown mode (0:CRU 1:GPIO) + * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH) + * @initialize: SoC special initialize tsadc controller method + * @irq_ack: clear the interrupt + * @get_temp: get the temperature + * @set_tshut_temp: set the hardware-controlled shutdown temperature + * @set_tshut_mode: set the hardware-controlled shutdown mode + * @table: the chip-specific conversion table + */ struct rockchip_tsadc_chip { /* The sensor id of chip correspond to the ADC channel */ int chn_id[SOC_MAX_SENSORS]; @@ -115,12 +127,32 @@ struct rockchip_tsadc_chip { struct chip_tsadc_table table; }; +/** + * struct rockchip_thermal_sensor - hold the information of thermal sensor + * @thermal: pointer to the platform/configuration data + * @tzd: pointer to a thermal zone + * @id: identifier of the thermal sensor + */ struct rockchip_thermal_sensor { struct rockchip_thermal_data *thermal; struct thermal_zone_device *tzd; int id; }; +/** + * struct rockchip_thermal_data - hold the private data of thermal driver + * @chip: pointer to the platform/configuration data + * @pdev: platform device of thermal + * @reset: the reset controller of tsadc + * @sensors[SOC_MAX_SENSORS]: the thermal sensor + * @clk: the controller clock is divided by the exteral 24MHz + * @pclk: the advanced peripherals bus clock + * @grf: the general register file will be used to do static set by software + * @regs: the base address of tsadc controller + * @tshut_temp: the hardware-controlled shutdown temperature value + * @tshut_mode: the hardware-controlled shutdown mode (0:CRU 1:GPIO) + * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH) + */ struct rockchip_thermal_data { const struct rockchip_tsadc_chip *chip; struct platform_device *pdev; @@ -160,12 +192,7 @@ struct rockchip_thermal_data { #define TSADCV2_AUTO_EN BIT(0) #define TSADCV2_AUTO_SRC_EN(chn) BIT(4 + (chn)) #define TSADCV2_AUTO_TSHUT_POLARITY_HIGH BIT(8) -/** - * TSADCV1_AUTO_Q_SEL_EN: - * whether select (1024 - tsadc_q) as output - * 1'b0:use tsadc_q as output(temperature-code is rising sequence) - * 1'b1:use(1024 - tsadc_q) as output (temperature-code is falling sequence) - */ + #define TSADCV3_AUTO_Q_SEL_EN BIT(1) #define TSADCV2_INT_SRC_EN(chn) BIT(chn) @@ -193,18 +220,21 @@ struct rockchip_thermal_data { #define GRF_SARADC_TESTBIT_ON (0x10001 << 2) #define GRF_TSADC_TESTBIT_H_ON (0x10001 << 2) -struct tsadc_table { - u32 code; - int temp; -}; - /** + * struct tsadc_table - code to temperature conversion table + * @code: the value of adc channel + * @temp: the temperature * Note: - * Code to Temperature mapping of the Temperature sensor is a piece wise linear + * code to temperature mapping of the temperature sensor is a piece wise linear * curve.Any temperature, code faling between to 2 give temperatures can be * linearly interpolated. - * Code to Temperature mapping should be updated based on sillcon results. + * Code to Temperature mapping should be updated based on manufacturer results. */ +struct tsadc_table { + u32 code; + int temp; +}; + static const struct tsadc_table rk3228_code_table[] = { {0, -40000}, {588, -40000}, @@ -490,6 +520,7 @@ static void rk_tsadcv2_initialize(struct regmap *grf, void __iomem *regs, /** * rk_tsadcv3_initialize - initialize TASDC Controller. + * * (1) The tsadc control power sequence. * * (2) Set TSADC_V2_AUTO_PERIOD: @@ -568,10 +599,11 @@ static void rk_tsadcv2_control(void __iomem *regs, bool enable) } /** - * @rk_tsadcv3_control: - * TSADC controller works at auto mode, and some SoCs need set the tsadc_q_sel - * bit on TSADCV2_AUTO_CON[1]. The (1024 - tsadc_q) as output adc value if - * setting this bit to enable. + * rk_tsadcv3_control - the tsadc controller is enabled or disabled. + * + * NOTE: TSADC controller works at auto mode, and some SoCs need set the + * tsadc_q_sel bit on TSADCV2_AUTO_CON[1]. The (1024 - tsadc_q) as output + * adc value if setting this bit to enable. */ static void rk_tsadcv3_control(void __iomem *regs, bool enable) { |