diff options
Diffstat (limited to 'drivers/net/dsa/microchip/ksz9477.c')
| -rw-r--r-- | drivers/net/dsa/microchip/ksz9477.c | 61 |
1 files changed, 57 insertions, 4 deletions
diff --git a/drivers/net/dsa/microchip/ksz9477.c b/drivers/net/dsa/microchip/ksz9477.c index f8ad7833f5d9..425e20daf1e9 100644 --- a/drivers/net/dsa/microchip/ksz9477.c +++ b/drivers/net/dsa/microchip/ksz9477.c @@ -355,10 +355,8 @@ int ksz9477_reset_switch(struct ksz_device *dev) SPI_AUTO_EDGE_DETECTION, 0); /* default configuration */ - ksz_read8(dev, REG_SW_LUE_CTRL_1, &data8); - data8 = SW_AGING_ENABLE | SW_LINK_AUTO_AGING | - SW_SRC_ADDR_FILTER | SW_FLUSH_STP_TABLE | SW_FLUSH_MSTP_TABLE; - ksz_write8(dev, REG_SW_LUE_CTRL_1, data8); + ksz_write8(dev, REG_SW_LUE_CTRL_1, + SW_AGING_ENABLE | SW_LINK_AUTO_AGING | SW_SRC_ADDR_FILTER); /* disable interrupts */ ksz_write32(dev, REG_SW_INT_MASK__4, SWITCH_INT_MASK); @@ -429,6 +427,57 @@ void ksz9477_freeze_mib(struct ksz_device *dev, int port, bool freeze) mutex_unlock(&p->mib.cnt_mutex); } +int ksz9477_errata_monitor(struct ksz_device *dev, int port, + u64 tx_late_col) +{ + u32 pmavbc; + u8 status; + u16 pqm; + int ret; + + ret = ksz_pread8(dev, port, REG_PORT_STATUS_0, &status); + if (ret) + return ret; + if (!(FIELD_GET(PORT_INTF_SPEED_MASK, status) == PORT_INTF_SPEED_NONE) && + !(status & PORT_INTF_FULL_DUPLEX)) { + /* Errata DS80000754 recommends monitoring potential faults in + * half-duplex mode. The switch might not be able to communicate anymore + * in these states. + * If you see this message, please read the errata-sheet for more information: + * https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ9477S-Errata-DS80000754.pdf + * To workaround this issue, half-duplex mode should be avoided. + * A software reset could be implemented to recover from this state. + */ + dev_warn_once(dev->dev, + "Half-duplex detected on port %d, transmission halt may occur\n", + port); + if (tx_late_col != 0) { + /* Transmission halt with late collisions */ + dev_crit_once(dev->dev, + "TX late collisions detected, transmission may be halted on port %d\n", + port); + } + ret = ksz_read8(dev, REG_SW_LUE_CTRL_0, &status); + if (ret) + return ret; + if (status & SW_VLAN_ENABLE) { + ret = ksz_pread16(dev, port, REG_PORT_QM_TX_CNT_0__4, &pqm); + if (ret) + return ret; + ret = ksz_read32(dev, REG_PMAVBC, &pmavbc); + if (ret) + return ret; + if ((FIELD_GET(PMAVBC_MASK, pmavbc) <= PMAVBC_MIN) || + (FIELD_GET(PORT_QM_TX_CNT_M, pqm) >= PORT_QM_TX_CNT_MAX)) { + /* Transmission halt with Half-Duplex and VLAN */ + dev_crit_once(dev->dev, + "resources out of limits, transmission may be halted\n"); + } + } + } + return ret; +} + void ksz9477_port_init_cnt(struct ksz_device *dev, int port) { struct ksz_port_mib *mib = &dev->ports[port].mib; @@ -1299,6 +1348,10 @@ int ksz9477_setup(struct dsa_switch *ds) /* Enable REG_SW_MTU__2 reg by setting SW_JUMBO_PACKET */ ksz_cfg(dev, REG_SW_MAC_CTRL_1, SW_JUMBO_PACKET, true); + /* Use collision based back pressure mode. */ + ksz_cfg(dev, REG_SW_MAC_CTRL_1, SW_BACK_PRESSURE, + SW_BACK_PRESSURE_COLLISION); + /* Now we can configure default MTU value */ ret = regmap_update_bits(ksz_regmap_16(dev), REG_SW_MTU__2, REG_SW_MTU_MASK, VLAN_ETH_FRAME_LEN + ETH_FCS_LEN); |