diff options
Diffstat (limited to 'Documentation')
43 files changed, 1344 insertions, 106 deletions
diff --git a/Documentation/arm/CCN.txt b/Documentation/arm/CCN.txt index 0632b3aad83e..ffca443a19b4 100644 --- a/Documentation/arm/CCN.txt +++ b/Documentation/arm/CCN.txt @@ -33,20 +33,23 @@ directory, with first 8 configurable by user and additional Cycle counter is described by a "type" value 0xff and does not require any other settings. +The driver also provides a "cpumask" sysfs attribute, which contains +a single CPU ID, of the processor which will be used to handle all +the CCN PMU events. It is recommended that the user space tools +request the events on this processor (if not, the perf_event->cpu value +will be overwritten anyway). In case of this processor being offlined, +the events are migrated to another one and the attribute is updated. + Example of perf tool use: / # perf list | grep ccn ccn/cycles/ [Kernel PMU event] <...> - ccn/xp_valid_flit/ [Kernel PMU event] + ccn/xp_valid_flit,xp=?,port=?,vc=?,dir=?/ [Kernel PMU event] <...> -/ # perf stat -C 0 -e ccn/cycles/,ccn/xp_valid_flit,xp=1,port=0,vc=1,dir=1/ \ +/ # perf stat -a -e ccn/cycles/,ccn/xp_valid_flit,xp=1,port=0,vc=1,dir=1/ \ sleep 1 The driver does not support sampling, therefore "perf record" will -not work. Also notice that only single cpu is being selected -("-C 0") - this is because perf framework does not support -"non-CPU related" counters (yet?) so system-wide session ("-a") -would try (and in most cases fail) to set up the same event -per each CPU. +not work. Per-task (without "-a") perf sessions are not supported. diff --git a/Documentation/arm/stm32/overview.txt b/Documentation/arm/stm32/overview.txt new file mode 100644 index 000000000000..09aed5588d7c --- /dev/null +++ b/Documentation/arm/stm32/overview.txt @@ -0,0 +1,32 @@ + STM32 ARM Linux Overview + ======================== + +Introduction +------------ + + The STMicroelectronics family of Cortex-M based MCUs are supported by the + 'STM32' platform of ARM Linux. Currently only the STM32F429 is supported. + + +Configuration +------------- + + A generic configuration is provided for STM32 family, and can be used as the + default by + make stm32_defconfig + +Layout +------ + + All the files for multiple machine families are located in the platform code + contained in arch/arm/mach-stm32 + + There is a generic board board-dt.c in the mach folder which support + Flattened Device Tree, which means, it works with any compatible board with + Device Trees. + + +Document Author +--------------- + + Maxime Coquelin <mcoquelin.stm32@gmail.com> diff --git a/Documentation/arm/stm32/stm32f429-overview.txt b/Documentation/arm/stm32/stm32f429-overview.txt new file mode 100644 index 000000000000..5206822bd8ef --- /dev/null +++ b/Documentation/arm/stm32/stm32f429-overview.txt @@ -0,0 +1,22 @@ + STM32F429 Overview + ================== + + Introduction + ------------ + The STM32F429 is a Cortex-M4 MCU aimed at various applications. + It features: + - ARM Cortex-M4 up to 180MHz with FPU + - 2MB internal Flash Memory + - External memory support through FMC controller (PSRAM, SDRAM, NOR, NAND) + - I2C, SPI, SAI, CAN, USB OTG, Ethernet controllers + - LCD controller & Camera interface + - Cryptographic processor + + Resources + --------- + Datasheet and reference manual are publicly available on ST website: + - http://www.st.com/web/en/catalog/mmc/FM141/SC1169/SS1577/LN1806?ecmp=stm32f429-439_pron_pr-ces2014_nov2013 + + Document Author + --------------- + Maxime Coquelin <mcoquelin.stm32@gmail.com> diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-controller.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-controller.txt new file mode 100644 index 000000000000..77ca635765e1 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-controller.txt @@ -0,0 +1,12 @@ +Altera SOCFPGA SDRAM Controller + +Required properties: +- compatible : Should contain "altr,sdr-ctl" and "syscon". + syscon is required by the Altera SOCFPGA SDRAM EDAC. +- reg : Should contain 1 register range (address and length) + +Example: + sdr: sdr@ffc25000 { + compatible = "altr,sdr-ctl", "syscon"; + reg = <0xffc25000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards index b78564b2b201..1a709970e7f7 100644 --- a/Documentation/devicetree/bindings/arm/arm-boards +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -157,3 +157,69 @@ Example: }; }; + +ARM Versatile Express Boards +----------------------------- +For details on the device tree bindings for ARM Versatile Express boards +please consult the vexpress.txt file in the same directory as this file. + +ARM Juno Boards +---------------- +The Juno boards are targeting development for AArch64 systems. The first +iteration, Juno r0, is a vehicle for evaluating big.LITTLE on AArch64, +with the second iteration, Juno r1, mainly aimed at development of PCIe +based systems. Juno r1 also has support for AXI masters placed on the TLX +connectors to join the coherency domain. + +Juno boards are described in a similar way to ARM Versatile Express boards, +with the motherboard part of the hardware being described in a separate file +to highlight the fact that is part of the support infrastructure for the SoC. +Juno device tree bindings also share the Versatile Express bindings as +described under the RS1 memory mapping. + +Required properties (in root node): + compatible = "arm,juno"; /* For Juno r0 board */ + compatible = "arm,juno-r1"; /* For Juno r1 board */ + +Required nodes: +The description for the board must include: + - a "psci" node describing the boot method used for the secondary CPUs. + A detailed description of the bindings used for "psci" nodes is present + in the psci.txt file. + - a "cpus" node describing the available cores and their associated + "enable-method"s. For more details see cpus.txt file. + +Example: + +/dts-v1/; +/ { + model = "ARM Juno development board (r0)"; + compatible = "arm,juno", "arm,vexpress"; + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + A57_0: cpu@0 { + compatible = "arm,cortex-a57","arm,armv8"; + reg = <0x0 0x0>; + device_type = "cpu"; + enable-method = "psci"; + }; + + ..... + + A53_0: cpu@100 { + compatible = "arm,cortex-a53","arm,armv8"; + reg = <0x0 0x100>; + device_type = "cpu"; + enable-method = "psci"; + }; + + ..... + }; + +}; diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index 2e99b5b57350..424ac8cbfa08 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -98,7 +98,7 @@ Example: }; RAMC SDRAM/DDR Controller required properties: -- compatible: Should be "atmel,at91rm9200-sdramc", +- compatible: Should be "atmel,at91rm9200-sdramc", "syscon" "atmel,at91sam9260-sdramc", "atmel,at91sam9g45-ddramc", "atmel,sama5d3-ddramc", diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt index ac683480c486..c78576bb7729 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt @@ -1,8 +1,35 @@ Broadcom BCM2835 device tree bindings ------------------------------------------- -Boards with the BCM2835 SoC shall have the following properties: +Raspberry Pi Model A +Required root node properties: +compatible = "raspberrypi,model-a", "brcm,bcm2835"; -Required root node property: +Raspberry Pi Model A+ +Required root node properties: +compatible = "raspberrypi,model-a-plus", "brcm,bcm2835"; +Raspberry Pi Model B +Required root node properties: +compatible = "raspberrypi,model-b", "brcm,bcm2835"; + +Raspberry Pi Model B (no P5) +early model B with I2C0 rather than I2C1 routed to the expansion header +Required root node properties: +compatible = "raspberrypi,model-b-i2c0", "brcm,bcm2835"; + +Raspberry Pi Model B rev2 +Required root node properties: +compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835"; + +Raspberry Pi Model B+ +Required root node properties: +compatible = "raspberrypi,model-b-plus", "brcm,bcm2835"; + +Raspberry Pi Compute Module +Required root node properties: +compatible = "raspberrypi,compute-module", "brcm,bcm2835"; + +Generic BCM2835 board +Required root node properties: compatible = "brcm,bcm2835"; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt index bd49987a8812..b82b6a0ae6f7 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt @@ -7,3 +7,79 @@ following properties: Required root node property: compatible: should be "brcm,bcm63138" + +An optional Boot lookup table Device Tree node is required for secondary CPU +initialization as well as a 'resets' phandle to the correct PMB controller as +defined in reset/brcm,bcm63138-pmb.txt for this secondary CPU, and an +'enable-method' property. + +Required properties for the Boot lookup table node: +- compatible: should be "brcm,bcm63138-bootlut" +- reg: register base address and length for the Boot Lookup table + +Optional properties for the primary CPU node: +- enable-method: should be "brcm,bcm63138" + +Optional properties for the secondary CPU node: +- enable-method: should be "brcm,bcm63138" +- resets: phandle to the relevant PMB controller, one integer indicating the internal + bus number, and a second integer indicating the address of the CPU in the PMB + internal bus number. + +Example: + + cpus { + cpu@0 { + compatible = "arm,cotex-a9"; + reg = <0>; + ... + enable-method = "brcm,bcm63138"; + }; + + cpu@1 { + compatible = "arm,cortex-a9"; + reg = <1>; + ... + enable-method = "brcm,bcm63138"; + resets = <&pmb0 4 1>; + }; + }; + + bootlut: bootlut@8000 { + compatible = "brcm,bcm63138-bootlut"; + reg = <0x8000 0x50>; + }; + +======= +reboot +------ +Two nodes are required for software reboot: a timer node and a syscon-reboot node. + +Timer node: + +- compatible: Must be "brcm,bcm6328-timer", "syscon" +- reg: Register base address and length + +Syscon reboot node: + +See Documentation/devicetree/bindings/power/reset/syscon-reboot.txt for the +detailed list of properties, the two values defined below are specific to the +BCM6328-style timer: + +- offset: Should be 0x34 to denote the offset of the TIMER_WD_TIMER_RESET register + from the beginning of the TIMER block +- mask: Should be 1 for the SoftRst bit. + +Example: + + timer: timer@80 { + compatible = "brcm,bcm6328-timer", "syscon"; + reg = <0x80 0x3c>; + }; + + reboot { + compatible = "syscon-reboot"; + regmap = <&timer>; + offset = <0x34>; + mask = <0x1>; + }; diff --git a/Documentation/devicetree/bindings/arm/cci.txt b/Documentation/devicetree/bindings/arm/cci.txt index 3c5c631328d3..aef1d200a9b2 100644 --- a/Documentation/devicetree/bindings/arm/cci.txt +++ b/Documentation/devicetree/bindings/arm/cci.txt @@ -31,8 +31,9 @@ specific to ARM. - compatible Usage: required Value type: <string> - Definition: must be set to + Definition: must contain one of the following: "arm,cci-400" + "arm,cci-500" - reg Usage: required @@ -99,6 +100,7 @@ specific to ARM. "arm,cci-400-pmu,r1" "arm,cci-400-pmu" - DEPRECATED, permitted only where OS has secure acces to CCI registers + "arm,cci-500-pmu,r0" - reg: Usage: required Value type: Integer cells. A register entry, expressed diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 6aa331d11c5e..d6b794cef0b8 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -188,6 +188,7 @@ nodes to be present and contain the properties described below. # On ARM 32-bit systems this property is optional and can be one of: "allwinner,sun6i-a31" + "allwinner,sun8i-a23" "arm,psci" "brcm,brahma-b15" "marvell,armada-375-smp" diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt index 5da38c5ed476..e151057d92f0 100644 --- a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt +++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt @@ -19,9 +19,10 @@ Optional Properties: domains. - clock-names: The following clocks can be specified: - oscclk: Oscillator clock. - - pclkN, clkN: Pairs of parent of input clock and input clock to the - devices in this power domain. Maximum of 4 pairs (N = 0 to 3) - are supported currently. + - clkN: Input clocks to the devices in this power domain. These clocks + will be reparented to oscclk before swithing power domain off. + Their original parent will be brought back after turning on + the domain. Maximum of 4 clocks (N = 0 to 3) are supported. - asbN: Clocks required by asynchronous bridges (ASB) present in the power domain. These clock should be enabled during power domain on/off operations. diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index a5462b6b3c30..2a3ba73f0c5c 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -81,12 +81,15 @@ Freescale Vybrid Platform Device Tree Bindings For the Vybrid SoC familiy all variants with DDR controller are supported, which is the VF5xx and VF6xx series. Out of historical reasons, in most places the kernel uses vf610 to refer to the whole familiy. +The compatible string "fsl,vf610m4" is used for the secondary Cortex-M4 +core support. Required root node compatible property (one of them): - compatible = "fsl,vf500"; - compatible = "fsl,vf510"; - compatible = "fsl,vf600"; - compatible = "fsl,vf610"; + - compatible = "fsl,vf610m4"; Freescale LS1021A Platform Device Tree Bindings ------------------------------------------------ diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt index 35b1bd49cfa1..c431c67524d6 100644 --- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt +++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt @@ -1,5 +1,8 @@ Hisilicon Platforms Device Tree Bindings ---------------------------------------------------- +Hi6220 SoC +Required root node properties: + - compatible = "hisilicon,hi6220"; Hi4511 Board Required root node properties: @@ -13,6 +16,9 @@ HiP01 ca9x2 Board Required root node properties: - compatible = "hisilicon,hip01-ca9x2"; +HiKey Board +Required root node properties: + - compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220"; Hisilicon system controller @@ -41,6 +47,87 @@ Example: }; ----------------------------------------------------------------------- +Hisilicon Hi6220 system controller + +Required properties: +- compatible : "hisilicon,hi6220-sysctrl" +- reg : Register address and size +- #clock-cells: should be set to 1, many clock registers are defined + under this controller and this property must be present. + +Hisilicon designs this controller as one of the system controllers, +its main functions are the same as Hisilicon system controller, but +the register offset of some core modules are different. + +Example: + /*for Hi6220*/ + sys_ctrl: sys_ctrl@f7030000 { + compatible = "hisilicon,hi6220-sysctrl", "syscon"; + reg = <0x0 0xf7030000 0x0 0x2000>; + #clock-cells = <1>; + }; + + +Hisilicon Hi6220 Power Always ON domain controller + +Required properties: +- compatible : "hisilicon,hi6220-aoctrl" +- reg : Register address and size +- #clock-cells: should be set to 1, many clock registers are defined + under this controller and this property must be present. + +Hisilicon designs this system controller to control the power always +on domain for mobile platform. + +Example: + /*for Hi6220*/ + ao_ctrl: ao_ctrl@f7800000 { + compatible = "hisilicon,hi6220-aoctrl", "syscon"; + reg = <0x0 0xf7800000 0x0 0x2000>; + #clock-cells = <1>; + }; + + +Hisilicon Hi6220 Media domain controller + +Required properties: +- compatible : "hisilicon,hi6220-mediactrl" +- reg : Register address and size +- #clock-cells: should be set to 1, many clock registers are defined + under this controller and this property must be present. + +Hisilicon designs this system controller to control the multimedia +domain(e.g. codec, G3D ...) for mobile platform. + +Example: + /*for Hi6220*/ + media_ctrl: media_ctrl@f4410000 { + compatible = "hisilicon,hi6220-mediactrl", "syscon"; + reg = <0x0 0xf4410000 0x0 0x1000>; + #clock-cells = <1>; + }; + + +Hisilicon Hi6220 Power Management domain controller + +Required properties: +- compatible : "hisilicon,hi6220-pmctrl" +- reg : Register address and size +- #clock-cells: should be set to 1, some clock registers are define + under this controller and this property must be present. + +Hisilicon designs this system controller to control the power management +domain for mobile platform. + +Example: + /*for Hi6220*/ + pm_ctrl: pm_ctrl@f7032000 { + compatible = "hisilicon,hi6220-pmctrl", "syscon"; + reg = <0x0 0xf7032000 0x0 0x1000>; + #clock-cells = <1>; + }; + +----------------------------------------------------------------------- Hisilicon HiP01 system controller Required properties: diff --git a/Documentation/devicetree/bindings/arm/marvell,berlin.txt b/Documentation/devicetree/bindings/arm/marvell,berlin.txt index a99eb9eb14c0..3bab18409b7a 100644 --- a/Documentation/devicetree/bindings/arm/marvell,berlin.txt +++ b/Documentation/devicetree/bindings/arm/marvell,berlin.txt @@ -1,6 +1,18 @@ Marvell Berlin SoC Family Device Tree Bindings --------------------------------------------------------------- +Work in progress statement: + +Device tree files and bindings applying to Marvell Berlin SoCs and boards are +considered "unstable". Any Marvell Berlin device tree binding may change at any +time. Be sure to use a device tree binary and a kernel image generated from the +same source tree. + +Please refer to Documentation/devicetree/bindings/ABI.txt for a definition of a +stable binding/ABI. + +--------------------------------------------------------------- + Boards with a SoC of the Marvell Berlin family, e.g. Armada 1500 shall have the following properties: @@ -49,10 +61,9 @@ chip control registers, so there should be a single DT node only providing the different functions which are described below. Required properties: -- compatible: shall be one of - "marvell,berlin2-chip-ctrl" for BG2 - "marvell,berlin2cd-chip-ctrl" for BG2CD - "marvell,berlin2q-chip-ctrl" for BG2Q +- compatible: + * the first and second values must be: + "simple-mfd", "syscon" - reg: address and length of following register sets for BG2/BG2CD: chip control register set BG2Q: chip control register set and cpu pll registers @@ -63,90 +74,23 @@ Marvell Berlin SoCs have a system control register set providing several individual registers dealing with pinmux, padmux, and reset. Required properties: -- compatible: should be one of - "marvell,berlin2-system-ctrl" for BG2 - "marvell,berlin2cd-system-ctrl" for BG2CD - "marvell,berlin2q-system-ctrl" for BG2Q +- compatible: + * the first and second values must be: + "simple-mfd", "syscon" - reg: address and length of the system control register set -* Clock provider binding - -As clock related registers are spread among the chip control registers, the -chip control node also provides the clocks. Marvell Berlin2 (BG2, BG2CD, BG2Q) -SoCs share the same IP for PLLs and clocks, with some minor differences in -features and register layout. - -Required properties: -- #clock-cells: shall be set to 1 -- clocks: clock specifiers referencing the core clock input clocks -- clock-names: array of strings describing the input clock specifiers above. - Allowed clock-names for the reference clocks are - "refclk" for the SoCs osciallator input on all SoCs, - and SoC-specific input clocks for - BG2/BG2CD: "video_ext0" for the external video clock input - -Clocks provided by core clocks shall be referenced by a clock specifier -indexing one of the provided clocks. Refer to dt-bindings/clock/berlin<soc>.h -for the corresponding index mapping. - -* Pin controller binding - -Pin control registers are part of both register sets, chip control and system -control. The pins controlled are organized in groups, so no actual pin -information is needed. - -A pin-controller node should contain subnodes representing the pin group -configurations, one per function. Each subnode has the group name and the muxing -function used. - -Be aware the Marvell Berlin datasheets use the keyword 'mode' for what is called -a 'function' in the pin-controller subsystem. - -Required subnode-properties: -- groups: a list of strings describing the group names. -- function: a string describing the function used to mux the groups. - -* Reset controller binding - -A reset controller is part of the chip control registers set. The chip control -node also provides the reset. The register set is not at the same offset between -Berlin SoCs. - -Required property: -- #reset-cells: must be set to 2 - Example: chip: chip-control@ea0000 { - compatible = "marvell,berlin2-chip-ctrl"; - #clock-cells = <1>; - #reset-cells = <2>; + compatible = "simple-mfd", "syscon"; reg = <0xea0000 0x400>; - clocks = <&refclk>, <&externaldev 0>; - clock-names = "refclk", "video_ext0"; - spi1_pmux: spi1-pmux { - groups = "G0"; - function = "spi1"; - }; + /* sub-device nodes */ }; sysctrl: system-controller@d000 { - compatible = "marvell,berlin2-system-ctrl"; + compatible = "simple-mfd", "syscon"; reg = <0xd000 0x100>; - uart0_pmux: uart0-pmux { - groups = "GSM4"; - function = "uart0"; - }; - - uart1_pmux: uart1-pmux { - groups = "GSM5"; - function = "uart1"; - }; - - uart2_pmux: uart2-pmux { - groups = "GSM3"; - function = "uart2"; - }; + /* sub-device nodes */ }; diff --git a/Documentation/devicetree/bindings/arm/scu.txt b/Documentation/devicetree/bindings/arm/scu.txt new file mode 100644 index 000000000000..c447680519bb --- /dev/null +++ b/Documentation/devicetree/bindings/arm/scu.txt @@ -0,0 +1,25 @@ +* ARM Snoop Control Unit (SCU) + +As part of the MPCore complex, Cortex-A5 and Cortex-A9 are provided +with a Snoop Control Unit. The register range is usually 256 (0x100) +bytes. + +References: + +- Cortex-A9: see DDI0407E Cortex-A9 MPCore Technical Reference Manual + Revision r2p0 +- Cortex-A5: see DDI0434B Cortex-A5 MPCore Technical Reference Manual + Revision r0p1 + +- compatible : Should be: + "arm,cortex-a9-scu" + "arm,cortex-a5-scu" + +- reg : Specify the base address and the size of the SCU register window. + +Example: + +scu@a04100000 { + compatible = "arm,cortex-a9-scu"; + reg = <0xa0410000 0x100>; +}; diff --git a/Documentation/devicetree/bindings/arm/ux500/boards.txt b/Documentation/devicetree/bindings/arm/ux500/boards.txt new file mode 100644 index 000000000000..b8737a8de718 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/ux500/boards.txt @@ -0,0 +1,83 @@ +ST-Ericsson Ux500 boards +------------------------ + +Required properties (in root node) one of these: + compatible = "st-ericsson,mop500" (legacy) + compatible = "st-ericsson,u8500" + +Required node (under root node): + +soc: represents the system-on-chip and contains the chip +peripherals + +Required property of soc node, one of these: + compatible = "stericsson,db8500" + +Required subnodes under soc node: + +backupram: (used for CPU spin tables and for storing data +during retention, system won't boot without this): + compatible = "ste,dbx500-backupram" + +scu: + see binding for arm/scu.txt + +interrupt-controller: + see binding for arm/gic.txt + +timer: + see binding for arm/twd.txt + +clocks: + see binding for clocks/ux500.txt + +Example: + +/dts-v1/; + +/ { + model = "ST-Ericsson HREF (pre-v60) and ST UIB"; + compatible = "st-ericsson,mop500", "st-ericsson,u8500"; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "stericsson,db8500"; + interrupt-parent = <&intc>; + ranges; + + backupram@80150000 { + compatible = "ste,dbx500-backupram"; + reg = <0x80150000 0x2000>; + }; + + intc: interrupt-controller@a0411000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <1>; + interrupt-controller; + reg = <0xa0411000 0x1000>, + <0xa0410100 0x100>; + }; + + scu@a04100000 { + compatible = "arm,cortex-a9-scu"; + reg = <0xa0410000 0x100>; + }; + + timer@a0410600 { + compatible = "arm,cortex-a9-twd-timer"; + reg = <0xa0410600 0x20>; + interrupts = <1 13 0x304>; /* IRQ level high per-CPU */ + clocks = <&smp_twd_clk>; + }; + + clocks { + compatible = "stericsson,u8500-clks"; + + smp_twd_clk: smp-twd-clock { + #clock-cells = <0>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/zte.txt b/Documentation/devicetree/bindings/arm/zte.txt new file mode 100644 index 000000000000..3ff5c9e85c1c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/zte.txt @@ -0,0 +1,15 @@ +ZTE platforms device tree bindings +--------------------------------------- + +- ZX296702 board: + Required root node properties: + - compatible = "zte,zx296702-ad1", "zte,zx296702" + +System management required properties: + - compatible = "zte,sysctrl" + +Low power management required properties: + - compatible = "zte,zx296702-pcu" + +Bus matrix required properties: + - compatible = "zte,zx-bus-matrix" diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index 7a4d4926f44e..5ba6450693b9 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -248,7 +248,7 @@ Required properties for peripheral clocks: - #address-cells : shall be 1 (reg is used to encode clk id). - clocks : shall be the master clock phandle. e.g. clocks = <&mck>; -- name: device tree node describing a specific system clock. +- name: device tree node describing a specific peripheral clock. * #clock-cells : from common clock binding; shall be set to 0. * reg: peripheral id. See Atmel's datasheets to get a full list of peripheral ids. diff --git a/Documentation/devicetree/bindings/clock/hi6220-clock.txt b/Documentation/devicetree/bindings/clock/hi6220-clock.txt new file mode 100644 index 000000000000..259e30af9597 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/hi6220-clock.txt @@ -0,0 +1,34 @@ +* Hisilicon Hi6220 Clock Controller + +Clock control registers reside in different Hi6220 system controllers, +please refer the following document to know more about the binding rules +for these system controllers: + +Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt + +Required Properties: + +- compatible: the compatible should be one of the following strings to + indicate the clock controller functionality. + + - "hisilicon,hi6220-aoctrl" + - "hisilicon,hi6220-sysctrl" + - "hisilicon,hi6220-mediactrl" + - "hisilicon,hi6220-pmctrl" + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +For example: + sys_ctrl: sys_ctrl@f7030000 { + compatible = "hisilicon,hi6220-sysctrl", "syscon"; + reg = <0x0 0xf7030000 0x0 0x2000>; + #clock-cells = <1>; + }; + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + +All these identifier could be found in <dt-bindings/clock/hi6220-clock.h>. diff --git a/Documentation/devicetree/bindings/clock/imx7d-clock.txt b/Documentation/devicetree/bindings/clock/imx7d-clock.txt new file mode 100644 index 000000000000..9d3026d81a68 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx7d-clock.txt @@ -0,0 +1,13 @@ +* Clock bindings for Freescale i.MX7 Dual + +Required properties: +- compatible: Should be "fsl,imx7d-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names +- clock-names: should include entries "ckil", "osc" + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx7d-clock.h +for the full list of i.MX7 Dual clock IDs. diff --git a/Documentation/devicetree/bindings/clock/marvell,berlin.txt b/Documentation/devicetree/bindings/clock/marvell,berlin.txt new file mode 100644 index 000000000000..c611c495f3ff --- /dev/null +++ b/Documentation/devicetree/bindings/clock/marvell,berlin.txt @@ -0,0 +1,31 @@ +Device Tree Clock bindings for Marvell Berlin + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Clock related registers are spread among the chip control registers. Berlin +clock node should be a sub-node of the chip controller node. Marvell Berlin2 +(BG2, BG2CD, BG2Q) SoCs share the same IP for PLLs and clocks, with some +minor differences in features and register layout. + +Required properties: +- compatible: must be "marvell,berlin2-clk" or "marvell,berlin2q-clk" +- #clock-cells: must be 1 +- clocks: must be the input parent clock phandle +- clock-names: name of the input parent clock + Allowed clock-names for the reference clocks are + "refclk" for the SoCs oscillator input on all SoCs, + and SoC-specific input clocks for + BG2/BG2CD: "video_ext0" for the external video clock input + + +Example: + +chip_clk: clock { + compatible = "marvell,berlin2q-clk"; + + #clock-cells = <1>; + clocks = <&refclk>; + clock-names = "refclk"; +}; diff --git a/Documentation/devicetree/bindings/clock/zx296702-clk.txt b/Documentation/devicetree/bindings/clock/zx296702-clk.txt new file mode 100644 index 000000000000..750442b65505 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/zx296702-clk.txt @@ -0,0 +1,35 @@ +Device Tree Clock bindings for ZTE zx296702 + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "zte,zx296702-topcrm-clk": + zx296702 top clock selection, divider and gating + + "zte,zx296702-lsp0crpm-clk" and + "zte,zx296702-lsp1crpm-clk": + zx296702 device level clock selection and gating + +- reg: Address and length of the register set + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/zx296702-clock.h +for the full list of zx296702 clock IDs. + + +topclk: topcrm@0x09800000 { + compatible = "zte,zx296702-topcrm-clk"; + reg = <0x09800000 0x1000>; + #clock-cells = <1>; +}; + +uart0: serial@0x09405000 { + compatible = "zte,zx296702-uart"; + reg = <0x09405000 0x1000>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&lsp1clk ZX296702_UART0_PCLK>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/fuse/nvidia,tegra20-fuse.txt b/Documentation/devicetree/bindings/fuse/nvidia,tegra20-fuse.txt index 23e1d3194174..41372d441131 100644 --- a/Documentation/devicetree/bindings/fuse/nvidia,tegra20-fuse.txt +++ b/Documentation/devicetree/bindings/fuse/nvidia,tegra20-fuse.txt @@ -29,7 +29,7 @@ Example: fuse@7000f800 { compatible = "nvidia,tegra20-efuse"; - reg = <0x7000F800 0x400>, + reg = <0x7000f800 0x400>, <0x70000000 0x400>; clocks = <&tegra_car TEGRA20_CLK_FUSE>; clock-names = "fuse"; diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt index 4b641c7bf1c2..09089a6d69ed 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt @@ -32,8 +32,8 @@ Example: touchscreen-fuzz-x = <4>; touchscreen-fuzz-y = <7>; touchscreen-fuzz-pressure = <2>; - touchscreen-max-x = <4096>; - touchscreen-max-y = <4096>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; touchscreen-max-pressure = <2048>; ti,x-plate-ohms = <280>; diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt index f3db93c85eea..3338a2834ad7 100644 --- a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt @@ -1,6 +1,9 @@ NVIDIA Tegra Memory Controller device tree bindings =================================================== +memory-controller node +---------------------- + Required properties: - compatible: Should be "nvidia,tegra<chip>-mc" - reg: Physical base address and length of the controller's registers. @@ -15,9 +18,49 @@ Required properties: This device implements an IOMMU that complies with the generic IOMMU binding. See ../iommu/iommu.txt for details. -Example: --------- +emc-timings subnode +------------------- + +The node should contain a "emc-timings" subnode for each supported RAM type (see field RAM_CODE in +register PMC_STRAPPING_OPT_A). + +Required properties for "emc-timings" nodes : +- nvidia,ram-code : Should contain the value of RAM_CODE this timing set is used for. + +timing subnode +-------------- + +Each "emc-timings" node should contain a subnode for every supported EMC clock rate. + +Required properties for timing nodes : +- clock-frequency : Should contain the memory clock rate in Hz. +- nvidia,emem-configuration : Values to be written to the EMEM register block. For the Tegra124 SoC +(see section "15.6.1 MC Registers" in the TRM), these are the registers whose values need to be +specified, according to the board documentation: + + MC_EMEM_ARB_CFG + MC_EMEM_ARB_OUTSTANDING_REQ + MC_EMEM_ARB_TIMING_RCD + MC_EMEM_ARB_TIMING_RP + MC_EMEM_ARB_TIMING_RC + MC_EMEM_ARB_TIMING_RAS + MC_EMEM_ARB_TIMING_FAW + MC_EMEM_ARB_TIMING_RRD + MC_EMEM_ARB_TIMING_RAP2PRE + MC_EMEM_ARB_TIMING_WAP2PRE + MC_EMEM_ARB_TIMING_R2R + MC_EMEM_ARB_TIMING_W2W + MC_EMEM_ARB_TIMING_R2W + MC_EMEM_ARB_TIMING_W2R + MC_EMEM_ARB_DA_TURNS + MC_EMEM_ARB_DA_COVERS + MC_EMEM_ARB_MISC0 + MC_EMEM_ARB_MISC1 + MC_EMEM_ARB_RING1_THROTTLE +Example SoC include file: + +/ { mc: memory-controller@0,70019000 { compatible = "nvidia,tegra124-mc"; reg = <0x0 0x70019000 0x0 0x1000>; @@ -34,3 +77,40 @@ Example: ... iommus = <&mc TEGRA_SWGROUP_SDMMC1A>; }; +}; + +Example board file: + +/ { + memory-controller@0,70019000 { + emc-timings-3 { + nvidia,ram-code = <3>; + + timing-12750000 { + clock-frequency = <12750000>; + + nvidia,emem-configuration = < + 0x40040001 /* MC_EMEM_ARB_CFG */ + 0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */ + 0x00000001 /* MC_EMEM_ARB_TIMING_RCD */ + 0x00000001 /* MC_EMEM_ARB_TIMING_RP */ + 0x00000002 /* MC_EMEM_ARB_TIMING_RC */ + 0x00000000 /* MC_EMEM_ARB_TIMING_RAS */ + 0x00000002 /* MC_EMEM_ARB_TIMING_FAW */ + 0x00000001 /* MC_EMEM_ARB_TIMING_RRD */ + 0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */ + 0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */ + 0x00000003 /* MC_EMEM_ARB_TIMING_R2R */ + 0x00000002 /* MC_EMEM_ARB_TIMING_W2W */ + 0x00000003 /* MC_EMEM_ARB_TIMING_R2W */ + 0x00000006 /* MC_EMEM_ARB_TIMING_W2R */ + 0x06030203 /* MC_EMEM_ARB_DA_TURNS */ + 0x000a0402 /* MC_EMEM_ARB_DA_COVERS */ + 0x77e30303 /* MC_EMEM_ARB_MISC0 */ + 0x70000f03 /* MC_EMEM_ARB_MISC1 */ + 0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */ + >; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt b/Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt new file mode 100644 index 000000000000..b59c625d6336 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt @@ -0,0 +1,374 @@ +NVIDIA Tegra124 SoC EMC (external memory controller) +==================================================== + +Required properties : +- compatible : Should be "nvidia,tegra124-emc". +- reg : physical base address and length of the controller's registers. +- nvidia,memory-controller : phandle of the MC driver. + +The node should contain a "emc-timings" subnode for each supported RAM type +(see field RAM_CODE in register PMC_STRAPPING_OPT_A), with its unit address +being its RAM_CODE. + +Required properties for "emc-timings" nodes : +- nvidia,ram-code : Should contain the value of RAM_CODE this timing set is +used for. + +Each "emc-timings" node should contain a "timing" subnode for every supported +EMC clock rate. The "timing" subnodes should have the clock rate in Hz as +their unit address. + +Required properties for "timing" nodes : +- clock-frequency : Should contain the memory clock rate in Hz. +- The following properties contain EMC timing characterization values +(specified in the board documentation) : + - nvidia,emc-auto-cal-config : EMC_AUTO_CAL_CONFIG + - nvidia,emc-auto-cal-config2 : EMC_AUTO_CAL_CONFIG2 + - nvidia,emc-auto-cal-config3 : EMC_AUTO_CAL_CONFIG3 + - nvidia,emc-auto-cal-interval : EMC_AUTO_CAL_INTERVAL + - nvidia,emc-bgbias-ctl0 : EMC_BGBIAS_CTL0 + - nvidia,emc-cfg : EMC_CFG + - nvidia,emc-cfg-2 : EMC_CFG_2 + - nvidia,emc-ctt-term-ctrl : EMC_CTT_TERM_CTRL + - nvidia,emc-mode-1 : Mode Register 1 + - nvidia,emc-mode-2 : Mode Register 2 + - nvidia,emc-mode-4 : Mode Register 4 + - nvidia,emc-mode-reset : Mode Register 0 + - nvidia,emc-mrs-wait-cnt : EMC_MRS_WAIT_CNT + - nvidia,emc-sel-dpd-ctrl : EMC_SEL_DPD_CTRL + - nvidia,emc-xm2dqspadctrl2 : EMC_XM2DQSPADCTRL2 + - nvidia,emc-zcal-cnt-long : EMC_ZCAL_WAIT_CNT after clock change + - nvidia,emc-zcal-interval : EMC_ZCAL_INTERVAL +- nvidia,emc-configuration : EMC timing characterization data. These are the +registers (see section "15.6.2 EMC Registers" in the TRM) whose values need to +be specified, according to the board documentation: + + EMC_RC + EMC_RFC + EMC_RFC_SLR + EMC_RAS + EMC_RP + EMC_R2W + EMC_W2R + EMC_R2P + EMC_W2P + EMC_RD_RCD + EMC_WR_RCD + EMC_RRD + EMC_REXT + EMC_WEXT + EMC_WDV + EMC_WDV_MASK + EMC_QUSE + EMC_QUSE_WIDTH + EMC_IBDLY + EMC_EINPUT + EMC_EINPUT_DURATION + EMC_PUTERM_EXTRA + EMC_PUTERM_WIDTH + EMC_PUTERM_ADJ + EMC_CDB_CNTL_1 + EMC_CDB_CNTL_2 + EMC_CDB_CNTL_3 + EMC_QRST + EMC_QSAFE + EMC_RDV + EMC_RDV_MASK + EMC_REFRESH + EMC_BURST_REFRESH_NUM + EMC_PRE_REFRESH_REQ_CNT + EMC_PDEX2WR + EMC_PDEX2RD + EMC_PCHG2PDEN + EMC_ACT2PDEN + EMC_AR2PDEN + EMC_RW2PDEN + EMC_TXSR + EMC_TXSRDLL + EMC_TCKE + EMC_TCKESR + EMC_TPD + EMC_TFAW + EMC_TRPAB + EMC_TCLKSTABLE + EMC_TCLKSTOP + EMC_TREFBW + EMC_FBIO_CFG6 + EMC_ODT_WRITE + EMC_ODT_READ + EMC_FBIO_CFG5 + EMC_CFG_DIG_DLL + EMC_CFG_DIG_DLL_PERIOD + EMC_DLL_XFORM_DQS0 + EMC_DLL_XFORM_DQS1 + EMC_DLL_XFORM_DQS2 + EMC_DLL_XFORM_DQS3 + EMC_DLL_XFORM_DQS4 + EMC_DLL_XFORM_DQS5 + EMC_DLL_XFORM_DQS6 + EMC_DLL_XFORM_DQS7 + EMC_DLL_XFORM_DQS8 + EMC_DLL_XFORM_DQS9 + EMC_DLL_XFORM_DQS10 + EMC_DLL_XFORM_DQS11 + EMC_DLL_XFORM_DQS12 + EMC_DLL_XFORM_DQS13 + EMC_DLL_XFORM_DQS14 + EMC_DLL_XFORM_DQS15 + EMC_DLL_XFORM_QUSE0 + EMC_DLL_XFORM_QUSE1 + EMC_DLL_XFORM_QUSE2 + EMC_DLL_XFORM_QUSE3 + EMC_DLL_XFORM_QUSE4 + EMC_DLL_XFORM_QUSE5 + EMC_DLL_XFORM_QUSE6 + EMC_DLL_XFORM_QUSE7 + EMC_DLL_XFORM_ADDR0 + EMC_DLL_XFORM_ADDR1 + EMC_DLL_XFORM_ADDR2 + EMC_DLL_XFORM_ADDR3 + EMC_DLL_XFORM_ADDR4 + EMC_DLL_XFORM_ADDR5 + EMC_DLL_XFORM_QUSE8 + EMC_DLL_XFORM_QUSE9 + EMC_DLL_XFORM_QUSE10 + EMC_DLL_XFORM_QUSE11 + EMC_DLL_XFORM_QUSE12 + EMC_DLL_XFORM_QUSE13 + EMC_DLL_XFORM_QUSE14 + EMC_DLL_XFORM_QUSE15 + EMC_DLI_TRIM_TXDQS0 + EMC_DLI_TRIM_TXDQS1 + EMC_DLI_TRIM_TXDQS2 + EMC_DLI_TRIM_TXDQS3 + EMC_DLI_TRIM_TXDQS4 + EMC_DLI_TRIM_TXDQS5 + EMC_DLI_TRIM_TXDQS6 + EMC_DLI_TRIM_TXDQS7 + EMC_DLI_TRIM_TXDQS8 + EMC_DLI_TRIM_TXDQS9 + EMC_DLI_TRIM_TXDQS10 + EMC_DLI_TRIM_TXDQS11 + EMC_DLI_TRIM_TXDQS12 + EMC_DLI_TRIM_TXDQS13 + EMC_DLI_TRIM_TXDQS14 + EMC_DLI_TRIM_TXDQS15 + EMC_DLL_XFORM_DQ0 + EMC_DLL_XFORM_DQ1 + EMC_DLL_XFORM_DQ2 + EMC_DLL_XFORM_DQ3 + EMC_DLL_XFORM_DQ4 + EMC_DLL_XFORM_DQ5 + EMC_DLL_XFORM_DQ6 + EMC_DLL_XFORM_DQ7 + EMC_XM2CMDPADCTRL + EMC_XM2CMDPADCTRL4 + EMC_XM2CMDPADCTRL5 + EMC_XM2DQPADCTRL2 + EMC_XM2DQPADCTRL3 + EMC_XM2CLKPADCTRL + EMC_XM2CLKPADCTRL2 + EMC_XM2COMPPADCTRL + EMC_XM2VTTGENPADCTRL + EMC_XM2VTTGENPADCTRL2 + EMC_XM2VTTGENPADCTRL3 + EMC_XM2DQSPADCTRL3 + EMC_XM2DQSPADCTRL4 + EMC_XM2DQSPADCTRL5 + EMC_XM2DQSPADCTRL6 + EMC_DSR_VTTGEN_DRV + EMC_TXDSRVTTGEN + EMC_FBIO_SPARE + EMC_ZCAL_WAIT_CNT + EMC_MRS_WAIT_CNT2 + EMC_CTT + EMC_CTT_DURATION + EMC_CFG_PIPE + EMC_DYN_SELF_REF_CONTROL + EMC_QPOP + +Example SoC include file: + +/ { + emc@0,7001b000 { + compatible = "nvidia,tegra124-emc"; + reg = <0x0 0x7001b000 0x0 0x1000>; + + nvidia,memory-controller = <&mc>; + }; +}; + +Example board file: + +/ { + emc@0,7001b000 { + emc-timings-3 { + nvidia,ram-code = <3>; + + timing-12750000 { + clock-frequency = <12750000>; + + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000000 /* EMC_RC */ + 0x00000003 /* EMC_RFC */ + 0x00000000 /* EMC_RFC_SLR */ + 0x00000000 /* EMC_RAS */ + 0x00000000 /* EMC_RP */ + 0x00000004 /* EMC_R2W */ + 0x0000000a /* EMC_W2R */ + 0x00000003 /* EMC_R2P */ + 0x0000000b /* EMC_W2P */ + 0x00000000 /* EMC_RD_RCD */ + 0x00000000 /* EMC_WR_RCD */ + 0x00000003 /* EMC_RRD */ + 0x00000003 /* EMC_REXT */ + 0x00000000 /* EMC_WEXT */ + 0x00000006 /* EMC_WDV */ + 0x00000006 /* EMC_WDV_MASK */ + 0x00000006 /* EMC_QUSE */ + 0x00000002 /* EMC_QUSE_WIDTH */ + 0x00000000 /* EMC_IBDLY */ + 0x00000005 /* EMC_EINPUT */ + 0x00000005 /* EMC_EINPUT_DURATION */ + 0x00010000 /* EMC_PUTERM_EXTRA */ + 0x00000003 /* EMC_PUTERM_WIDTH */ + 0x00000000 /* EMC_PUTERM_ADJ */ + 0x00000000 /* EMC_CDB_CNTL_1 */ + 0x00000000 /* EMC_CDB_CNTL_2 */ + 0x00000000 /* EMC_CDB_CNTL_3 */ + 0x00000004 /* EMC_QRST */ + 0x0000000c /* EMC_QSAFE */ + 0x0000000d /* EMC_RDV */ + 0x0000000f /* EMC_RDV_MASK */ + 0x00000060 /* EMC_REFRESH */ + 0x00000000 /* EMC_BURST_REFRESH_NUM */ + 0x00000018 /* EMC_PRE_REFRESH_REQ_CNT */ + 0x00000002 /* EMC_PDEX2WR */ + 0x00000002 /* EMC_PDEX2RD */ + 0x00000001 /* EMC_PCHG2PDEN */ + 0x00000000 /* EMC_ACT2PDEN */ + 0x00000007 /* EMC_AR2PDEN */ + 0x0000000f /* EMC_RW2PDEN */ + 0x00000005 /* EMC_TXSR */ + 0x00000005 /* EMC_TXSRDLL */ + 0x00000004 /* EMC_TCKE */ + 0x00000005 /* EMC_TCKESR */ + 0x00000004 /* EMC_TPD */ + 0x00000000 /* EMC_TFAW */ + 0x00000000 /* EMC_TRPAB */ + 0x00000005 /* EMC_TCLKSTABLE */ + 0x00000005 /* EMC_TCLKSTOP */ + 0x00000064 /* EMC_TREFBW */ + 0x00000000 /* EMC_FBIO_CFG6 */ + 0x00000000 /* EMC_ODT_WRITE */ + 0x00000000 /* EMC_ODT_READ */ + 0x106aa298 /* EMC_FBIO_CFG5 */ + 0x002c00a0 /* EMC_CFG_DIG_DLL */ + 0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */ + 0x00064000 /* EMC_DLL_XFORM_DQS0 */ + 0x00064000 /* EMC_DLL_XFORM_DQS1 */ + 0x00064000 /* EMC_DLL_XFORM_DQS2 */ + 0x00064000 /* EMC_DLL_XFORM_DQS3 */ + 0x00064000 /* EMC_DLL_XFORM_DQS4 */ + 0x00064000 /* EMC_DLL_XFORM_DQS5 */ + 0x00064000 /* EMC_DLL_XFORM_DQS6 */ + 0x00064000 /* EMC_DLL_XFORM_DQS7 */ + 0x00064000 /* EMC_DLL_XFORM_DQS8 */ + 0x00064000 /* EMC_DLL_XFORM_DQS9 */ + 0x00064000 /* EMC_DLL_XFORM_DQS10 */ + 0x00064000 /* EMC_DLL_XFORM_DQS11 */ + 0x00064000 /* EMC_DLL_XFORM_DQS12 */ + 0x00064000 /* EMC_DLL_XFORM_DQS13 */ + 0x00064000 /* EMC_DLL_XFORM_DQS14 */ + 0x00064000 /* EMC_DLL_XFORM_DQS15 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE0 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE1 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE2 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE3 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE4 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE5 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE6 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE7 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR0 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR1 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR2 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR3 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR4 */ + 0x00000000 /* EMC_DLL_XFORM_ADDR5 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE8 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE9 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE10 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE11 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE12 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE13 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE14 */ + 0x00000000 /* EMC_DLL_XFORM_QUSE15 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS0 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS1 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS2 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS3 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS4 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS5 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS6 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS7 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS8 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS9 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS10 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS11 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS12 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS13 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS14 */ + 0x00000000 /* EMC_DLI_TRIM_TXDQS15 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ0 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ1 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ2 */ + 0x000fc000 /* EMC_DLL_XFORM_DQ3 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ4 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ5 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ6 */ + 0x0000fc00 /* EMC_DLL_XFORM_DQ7 */ + 0x10000280 /* EMC_XM2CMDPADCTRL */ + 0x00000000 /* EMC_XM2CMDPADCTRL4 */ + 0x00111111 /* EMC_XM2CMDPADCTRL5 */ + 0x00000000 /* EMC_XM2DQPADCTRL2 */ + 0x00000000 /* EMC_XM2DQPADCTRL3 */ + 0x77ffc081 /* EMC_XM2CLKPADCTRL */ + 0x00000e0e /* EMC_XM2CLKPADCTRL2 */ + 0x81f1f108 /* EMC_XM2COMPPADCTRL */ + 0x07070004 /* EMC_XM2VTTGENPADCTRL */ + 0x0000003f /* EMC_XM2VTTGENPADCTRL2 */ + 0x016eeeee /* EMC_XM2VTTGENPADCTRL3 */ + 0x51451400 /* EMC_XM2DQSPADCTRL3 */ + 0x00514514 /* EMC_XM2DQSPADCTRL4 */ + 0x00514514 /* EMC_XM2DQSPADCTRL5 */ + 0x51451400 /* EMC_XM2DQSPADCTRL6 */ + 0x0000003f /* EMC_DSR_VTTGEN_DRV */ + 0x00000007 /* EMC_TXDSRVTTGEN */ + 0x00000000 /* EMC_FBIO_SPARE */ + 0x00000042 /* EMC_ZCAL_WAIT_CNT */ + 0x000e000e /* EMC_MRS_WAIT_CNT2 */ + 0x00000000 /* EMC_CTT */ + 0x00000003 /* EMC_CTT_DURATION */ + 0x0000f2f3 /* EMC_CFG_PIPE */ + 0x800001c5 /* EMC_DYN_SELF_REF_CONTROL */ + 0x0000000a /* EMC_QPOP */ + >; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/mfd.txt b/Documentation/devicetree/bindings/mfd/mfd.txt new file mode 100644 index 000000000000..af9d6931a1a2 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/mfd.txt @@ -0,0 +1,41 @@ +Multi-Function Devices (MFD) + +These devices comprise a nexus for heterogeneous hardware blocks containing +more than one non-unique yet varying hardware functionality. + +A typical MFD can be: + +- A mixed signal ASIC on an external bus, sometimes a PMIC (Power Management + Integrated Circuit) that is manufactured in a lower technology node (rough + silicon) that handles analog drivers for things like audio amplifiers, LED + drivers, level shifters, PHY (physical interfaces to things like USB or + ethernet), regulators etc. + +- A range of memory registers containing "miscellaneous system registers" also + known as a system controller "syscon" or any other memory range containing a + mix of unrelated hardware devices. + +Optional properties: + +- compatible : "simple-mfd" - this signifies that the operating system should + consider all subnodes of the MFD device as separate devices akin to how + "simple-bus" inidicates when to see subnodes as children for a simple + memory-mapped bus. For more complex devices, when the nexus driver has to + probe registers to figure out what child devices exist etc, this should not + be used. In the latter case the child devices will be determined by the + operating system. + +Example: + +foo@1000 { + compatible = "syscon", "simple-mfd"; + reg = <0x01000 0x1000>; + + led@08.0 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x01>; + label = "myled"; + default-state = "on"; + }; +}; diff --git a/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt b/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt index 47b205cc9cc7..4556359c5876 100644 --- a/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt +++ b/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt @@ -10,3 +10,5 @@ Required properties: The second entry gives the physical address and length of the registers indicating the strapping options. +Optional properties: +- nvidia,long-ram-code: If present, the RAM code is long (4 bit). If not, short (2 bit). diff --git a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt index 3e2c88d97ad4..02f979a48aeb 100644 --- a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt +++ b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt @@ -58,5 +58,5 @@ Example: interrupt-controller; #address-cells = <0>; #interrupt-cells = <1>; - } + }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt new file mode 100644 index 000000000000..a8bb5e26019c --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt @@ -0,0 +1,43 @@ +* Pin-controller driver for the Marvell Berlin SoCs + +Pin control registers are part of both chip controller and system +controller register sets. Pin controller nodes should be a sub-node of +either the chip controller or system controller node. The pins +controlled are organized in groups, so no actual pin information is +needed. + +A pin-controller node should contain subnodes representing the pin group +configurations, one per function. Each subnode has the group name and +the muxing function used. + +Be aware the Marvell Berlin datasheets use the keyword 'mode' for what +is called a 'function' in the pin-controller subsystem. + +Required properties: +- compatible: should be one of: + "marvell,berlin2-soc-pinctrl", + "marvell,berlin2-system-pinctrl", + "marvell,berlin2cd-soc-pinctrl", + "marvell,berlin2cd-system-pinctrl", + "marvell,berlin2q-soc-pinctrl", + "marvell,berlin2q-system-pinctrl" + +Required subnode-properties: +- groups: a list of strings describing the group names. +- function: a string describing the function used to mux the groups. + +Example: + +sys_pinctrl: pin-controller { + compatible = "marvell,berlin2q-system-pinctrl"; + + uart0_pmux: uart0-pmux { + groups = "GSM12"; + function = "uart0"; + }; +}; + +&uart0 { + pinctrl-0 = <&uart0_pmux>; + pinctrl-names = "default"; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt new file mode 100644 index 000000000000..8bbf25d58656 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt @@ -0,0 +1,27 @@ +* Freescale i.MX7 Dual IOMUX Controller + +Please refer to fsl,imx-pinctrl.txt in this directory for common binding part +and usage. + +Required properties: +- compatible: "fsl,imx7d-iomuxc" +- fsl,pins: each entry consists of 6 integers and represents the mux and config + setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val + input_val> are specified using a PIN_FUNC_ID macro, which can be found in + imx7d-pinfunc.h under device tree source folder. The last integer CONFIG is + the pad setting value like pull-up on this pin. Please refer to i.MX7 Dual + Reference Manual for detailed CONFIG settings. + +CONFIG bits definition: +PAD_CTL_PUS_100K_DOWN (0 << 5) +PAD_CTL_PUS_5K_UP (1 << 5) +PAD_CTL_PUS_47K_UP (2 << 5) +PAD_CTL_PUS_100K_UP (3 << 5) +PAD_CTL_PUE (1 << 4) +PAD_CTL_HYS (1 << 3) +PAD_CTL_SRE_SLOW (1 << 2) +PAD_CTL_SRE_FAST (0 << 2) +PAD_CTL_DSE_X1 (0 << 0) +PAD_CTL_DSE_X2 (1 << 0) +PAD_CTL_DSE_X3 (2 << 0) +PAD_CTL_DSE_X4 (3 << 0) diff --git a/Documentation/devicetree/bindings/reset/berlin,reset.txt b/Documentation/devicetree/bindings/reset/berlin,reset.txt new file mode 100644 index 000000000000..514fee098b4b --- /dev/null +++ b/Documentation/devicetree/bindings/reset/berlin,reset.txt @@ -0,0 +1,23 @@ +Marvell Berlin reset controller +=============================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +The reset controller node must be a sub-node of the chip controller +node on Berlin SoCs. + +Required properties: +- compatible: should be "marvell,berlin2-reset" +- #reset-cells: must be set to 2 + +Example: + +chip_rst: reset { + compatible = "marvell,berlin2-reset"; + #reset-cells = <2>; +}; + +&usb_phy0 { + resets = <&chip_rst 0x104 12>; +}; diff --git a/Documentation/devicetree/bindings/reset/brcm,bcm63138-pmb.txt b/Documentation/devicetree/bindings/reset/brcm,bcm63138-pmb.txt new file mode 100644 index 000000000000..a98872d27872 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/brcm,bcm63138-pmb.txt @@ -0,0 +1,19 @@ +Broadcom BCM63138 Processor Monitor Bus binding +=============================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Require properties: + +- compatible: must be "brcm,bcm63138-pmb" +- reg: base register address and size for this bus controller +- #reset-cells: must be 2 first cell is the address within the bus instance designated + by the phandle, and the second is the number of zones for this peripheral + +Example: + pmb0: reset-controller@4800c0 { + compatible = "brcm,bcm63138-pmb"; + reg = <0x4800c0 0x10>; + #reset-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt index ab757b84daa7..ac2fcd6ff4b8 100644 --- a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt @@ -6,7 +6,8 @@ Required properties: * "samsung,s3c2416-rtc" - for controllers compatible with s3c2416 rtc. * "samsung,s3c2443-rtc" - for controllers compatible with s3c2443 rtc. * "samsung,s3c6410-rtc" - for controllers compatible with s3c6410 rtc. - * "samsung,exynos3250-rtc" - for controllers compatible with exynos3250 rtc. + * "samsung,exynos3250-rtc" - (deprecated) for controllers compatible with + exynos3250 rtc (use "samsung,s3c6410-rtc"). - reg: physical base address of the controller and length of memory mapped region. - interrupts: Two interrupt numbers to the cpu should be specified. First diff --git a/Documentation/devicetree/bindings/serial/pl011.txt b/Documentation/devicetree/bindings/serial/pl011.txt index ba3ecb8cb5a1..cbae3d9a0278 100644 --- a/Documentation/devicetree/bindings/serial/pl011.txt +++ b/Documentation/devicetree/bindings/serial/pl011.txt @@ -1,7 +1,7 @@ * ARM AMBA Primecell PL011 serial UART Required properties: -- compatible: must be "arm,primecell", "arm,pl011" +- compatible: must be "arm,primecell", "arm,pl011", "zte,zx296702-uart" - reg: exactly one register range with length 0x1000 - interrupts: exactly one interrupt specifier diff --git a/Documentation/devicetree/bindings/soc/sunxi/sram.txt b/Documentation/devicetree/bindings/soc/sunxi/sram.txt new file mode 100644 index 000000000000..067698112f5f --- /dev/null +++ b/Documentation/devicetree/bindings/soc/sunxi/sram.txt @@ -0,0 +1,72 @@ +Allwinnner SoC SRAM controllers +----------------------------------------------------- + +The SRAM controller found on most Allwinner devices is represented by +a regular node for the SRAM controller itself, with sub-nodes +reprensenting the SRAM handled by the SRAM controller. + +Controller Node +--------------- + +Required properties: +- compatible : "allwinner,sun4i-a10-sram-controller" +- reg : sram controller register offset + length + +SRAM nodes +---------- + +Each SRAM is described using the mmio-sram bindings documented in +Documentation/devicetree/bindings/misc/sram.txt + +Each SRAM will have SRAM sections that are going to be handled by the +SRAM controller as subnodes. These sections are represented following +once again the representation described in the mmio-sram binding. + +The valid sections compatible are: + - allwinner,sun4i-a10-sram-a3-a4 + - allwinner,sun4i-a10-sram-d + +Devices using SRAM sections +--------------------------- + +Some devices need to request to the SRAM controller to map an SRAM for +their exclusive use. + +The relationship between such a device and an SRAM section is +expressed through the allwinner,sram property, that will take a +phandle and an argument. + +This valid values for this argument are: + - 0: CPU + - 1: Device + +Example +------- +sram-controller@01c00000 { + compatible = "allwinner,sun4i-a10-sram-controller"; + reg = <0x01c00000 0x30>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + sram_a: sram@00000000 { + compatible = "mmio-sram"; + reg = <0x00000000 0xc000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x00000000 0xc000>; + + emac_sram: sram-section@8000 { + compatible = "allwinner,sun4i-a10-sram-a3-a4"; + reg = <0x8000 0x4000>; + status = "disabled"; + }; + }; +}; + +emac: ethernet@01c0b000 { + compatible = "allwinner,sun4i-a10-emac"; + ... + + allwinner,sram = <&emac_sram 1>; +}; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index 4c388bb2f0a2..8f771441be60 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -60,7 +60,7 @@ Example: msiof0: spi@e6e20000 { compatible = "renesas,msiof-r8a7791"; - reg = <0 0xe6e20000 0 0x0064>, <0 0xe7e20000 0 0x0064>; + reg = <0 0xe6e20000 0 0x0064>; interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>; dmas = <&dmac0 0x51>, <&dmac0 0x52>; diff --git a/Documentation/devicetree/bindings/timer/cadence,ttc-timer.txt b/Documentation/devicetree/bindings/timer/cadence,ttc-timer.txt index 993695c659e1..eeee6cd51e5c 100644 --- a/Documentation/devicetree/bindings/timer/cadence,ttc-timer.txt +++ b/Documentation/devicetree/bindings/timer/cadence,ttc-timer.txt @@ -6,6 +6,9 @@ Required properties: - interrupts : A list of 3 interrupts; one per timer channel. - clocks: phandle to the source clock +Optional properties: +- timer-width: Bit width of the timer, necessary if not 16. + Example: ttc0: ttc0@f8001000 { @@ -14,4 +17,5 @@ ttc0: ttc0@f8001000 { compatible = "cdns,ttc"; reg = <0xF8001000 0x1000>; clocks = <&cpu_clk 3>; + timer-width = <32>; }; diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt index e180d56c75db..1be8d7a26c15 100644 --- a/Documentation/devicetree/bindings/usb/atmel-usb.txt +++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt @@ -5,6 +5,13 @@ OHCI Required properties: - compatible: Should be "atmel,at91rm9200-ohci" for USB controllers used in host mode. + - reg: Address and length of the register set for the device + - interrupts: Should contain ehci interrupt + - clocks: Should reference the peripheral, host and system clocks + - clock-names: Should contains two strings + "ohci_clk" for the peripheral clock + "hclk" for the host clock + "uhpck" for the system clock - num-ports: Number of ports. - atmel,vbus-gpio: If present, specifies a gpio that needs to be activated for the bus to be powered. @@ -14,6 +21,8 @@ Required properties: usb0: ohci@00500000 { compatible = "atmel,at91rm9200-ohci", "usb-ohci"; reg = <0x00500000 0x100000>; + clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>; + clock-names = "ohci_clk", "hclk", "uhpck"; interrupts = <20 4>; num-ports = <2>; }; @@ -23,11 +32,19 @@ EHCI Required properties: - compatible: Should be "atmel,at91sam9g45-ehci" for USB controllers used in host mode. + - reg: Address and length of the register set for the device + - interrupts: Should contain ehci interrupt + - clocks: Should reference the peripheral and the UTMI clocks + - clock-names: Should contains two strings + "ehci_clk" for the peripheral clock + "usb_clk" for the UTMI clock usb1: ehci@00800000 { compatible = "atmel,at91sam9g45-ehci", "usb-ehci"; reg = <0x00800000 0x100000>; interrupts = <22 4>; + clocks = <&utmi>, <&uhphs_clk>; + clock-names = "usb_clk", "ehci_clk"; }; AT91 USB device controller @@ -53,6 +70,8 @@ usb1: gadget@fffa4000 { compatible = "atmel,at91rm9200-udc"; reg = <0xfffa4000 0x4000>; interrupts = <10 4>; + clocks = <&udc_clk>, <&udpck>; + clock-names = "pclk", "hclk"; atmel,vbus-gpio = <&pioC 5 0>; }; @@ -65,6 +84,10 @@ Required properties: "sama5d3-udc" - reg: Address and length of the register set for the device - interrupts: Should contain usba interrupt + - clocks: Should reference the peripheral and host clocks + - clock-names: Should contains two strings + "pclk" for the peripheral clock + "hclk" for the host clock - ep childnode: To specify the number of endpoints and their properties. Optional properties: @@ -86,6 +109,8 @@ usb2: gadget@fff78000 { reg = <0x00600000 0x80000 0xfff78000 0x400>; interrupts = <27 4 0>; + clocks = <&utmi>, <&udphs_clk>; + clock-names = "hclk", "pclk"; atmel,vbus-gpio = <&pioB 19 0>; ep0 { diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 80339192c93e..49cecc9e9d4d 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -40,6 +40,7 @@ calxeda Calxeda capella Capella Microsystems, Inc cavium Cavium, Inc. cdns Cadence Design Systems Inc. +ceva Ceva, Inc. chipidea Chipidea, Inc chipone ChipOne chipspark ChipSPARK @@ -52,6 +53,7 @@ cnxt Conexant Systems, Inc. cortina Cortina Systems, Inc. cosmic Cosmic Circuits crystalfontz Crystalfontz America, Inc. +cubietech Cubietech, Ltd. dallas Maxim Integrated Products (formerly Dallas Semiconductor) davicom DAVICOM Semiconductor, Inc. denx Denx Software Engineering @@ -60,6 +62,7 @@ digilent Diglent, Inc. dlg Dialog Semiconductor dlink D-Link Corporation dmo Data Modul AG +ea Embedded Artists AB ebv EBV Elektronik edt Emerging Display Technologies elan Elan Microelectronic Corp. @@ -90,9 +93,11 @@ gumstix Gumstix, Inc. gw Gateworks Corporation hannstar HannStar Display Corporation haoyu Haoyu Microelectronic Co. Ltd. +hardkernel Hardkernel Co., Ltd himax Himax Technologies, Inc. hisilicon Hisilicon Limited. hit Hitachi Ltd. +hitex Hitex Development Tools honeywell Honeywell hp Hewlett Packard i2se I2SE GmbH @@ -159,6 +164,7 @@ radxa Radxa raidsonic RaidSonic Technology GmbH ralink Mediatek/Ralink Technology Corp. ramtron Ramtron International +raspberrypi Raspberry Pi Foundation realtek Realtek Semiconductor Corp. renesas Renesas Electronics Corporation ricoh Ricoh Co. Ltd. @@ -189,6 +195,7 @@ ste ST-Ericsson stericsson ST-Ericsson synology Synology, Inc. tbs TBS Technologies +tcl Toby Churchill Ltd. thine THine Electronics, Inc. ti Texas Instruments tlm Trusted Logic Mobility @@ -202,6 +209,7 @@ variscite Variscite Ltd. via VIA Technologies, Inc. virtio Virtual I/O Device Specification, developed by the OASIS consortium voipac Voipac Technologies s.r.o. +wexler Wexler winbond Winbond Electronics corp. wlf Wolfson Microelectronics wm Wondermedia Technologies, Inc. @@ -211,3 +219,4 @@ xillybus Xillybus Ltd. xlnx Xilinx zyxel ZyXEL Communications Corp. zarlink Zarlink Semiconductor +zte ZTE Corp. diff --git a/Documentation/i2c/slave-interface b/Documentation/i2c/slave-interface index 389bb5d61854..b228ca54bcf4 100644 --- a/Documentation/i2c/slave-interface +++ b/Documentation/i2c/slave-interface @@ -31,10 +31,10 @@ User manual =========== I2C slave backends behave like standard I2C clients. So, you can instantiate -them like described in the document 'instantiating-devices'. A quick example -for instantiating the slave-eeprom driver from userspace: +them as described in the document 'instantiating-devices'. A quick example for +instantiating the slave-eeprom driver from userspace at address 0x64 on bus 1: - # echo 0-0064 > /sys/bus/i2c/drivers/i2c-slave-eeprom/bind + # echo slave-24c02 0x64 > /sys/bus/i2c/devices/i2c-1/new_device Each backend should come with separate documentation to describe its specific behaviour and setup. diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 55bb093a08a3..59ecd3d558c8 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1482,6 +1482,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted. By default, super page will be supported if Intel IOMMU has the capability. With this option, super page will not be supported. + ecs_off [Default Off] + By default, extended context tables will be supported if + the hardware advertises that it has support both for the + extended tables themselves, and also PASID support. With + this option set, extended tables will not be used even + on hardware which claims to support them. intel_idle.max_cstate= [KNL,HW,ACPI,X86] 0 disables intel_idle and fall back on acpi_idle. diff --git a/Documentation/networking/udplite.txt b/Documentation/networking/udplite.txt index d727a3829100..53a726855e49 100644 --- a/Documentation/networking/udplite.txt +++ b/Documentation/networking/udplite.txt @@ -20,7 +20,7 @@ files/UDP-Lite-HOWTO.txt o The Wireshark UDP-Lite WiKi (with capture files): - http://wiki.wireshark.org/Lightweight_User_Datagram_Protocol + https://wiki.wireshark.org/Lightweight_User_Datagram_Protocol o The Protocol Spec, RFC 3828, http://www.ietf.org/rfc/rfc3828.txt |