diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/dsa/realtek-smi.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/net/dsa/realtek-smi.txt | 240 |
1 files changed, 0 insertions, 240 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt deleted file mode 100644 index 7959ec237983..000000000000 --- a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt +++ /dev/null @@ -1,240 +0,0 @@ -Realtek SMI-based Switches -========================== - -The SMI "Simple Management Interface" is a two-wire protocol using -bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does -not use the MDIO protocol. This binding defines how to specify the -SMI-based Realtek devices. - -Required properties: - -- compatible: must be exactly one of: - "realtek,rtl8365mb" (4+1 ports) - "realtek,rtl8366" - "realtek,rtl8366rb" (4+1 ports) - "realtek,rtl8366s" (4+1 ports) - "realtek,rtl8367" - "realtek,rtl8367b" - "realtek,rtl8368s" (8 port) - "realtek,rtl8369" - "realtek,rtl8370" (8 port) - -Required properties: -- mdc-gpios: GPIO line for the MDC clock line. -- mdio-gpios: GPIO line for the MDIO data line. -- reset-gpios: GPIO line for the reset signal. - -Optional properties: -- realtek,disable-leds: if the LED drivers are not used in the - hardware design this will disable them so they are not turned on - and wasting power. - -Required subnodes: - -- interrupt-controller - - This defines an interrupt controller with an IRQ line (typically - a GPIO) that will demultiplex and handle the interrupt from the single - interrupt line coming out of one of the SMI-based chips. It most - importantly provides link up/down interrupts to the PHY blocks inside - the ASIC. - -Required properties of interrupt-controller: - -- interrupt: parent interrupt, see interrupt-controller/interrupts.txt -- interrupt-controller: see interrupt-controller/interrupts.txt -- #address-cells: should be <0> -- #interrupt-cells: should be <1> - -- mdio - - This defines the internal MDIO bus of the SMI device, mostly for the - purpose of being able to hook the interrupts to the right PHY and - the right PHY to the corresponding port. - -Required properties of mdio: - -- compatible: should be set to "realtek,smi-mdio" for all SMI devices - -See net/mdio.txt for additional MDIO bus properties. - -See net/dsa/dsa.txt for a list of additional required and optional properties -and subnodes of DSA switches. - -Examples: - -An example for the RTL8366RB: - -switch { - compatible = "realtek,rtl8366rb"; - /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */ - mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; - mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; - - switch_intc: interrupt-controller { - /* GPIO 15 provides the interrupt */ - interrupt-parent = <&gpio0>; - interrupts = <15 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #address-cells = <0>; - #interrupt-cells = <1>; - }; - - ports { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - port@0 { - reg = <0>; - label = "lan0"; - phy-handle = <&phy0>; - }; - port@1 { - reg = <1>; - label = "lan1"; - phy-handle = <&phy1>; - }; - port@2 { - reg = <2>; - label = "lan2"; - phy-handle = <&phy2>; - }; - port@3 { - reg = <3>; - label = "lan3"; - phy-handle = <&phy3>; - }; - port@4 { - reg = <4>; - label = "wan"; - phy-handle = <&phy4>; - }; - port@5 { - reg = <5>; - label = "cpu"; - ethernet = <&gmac0>; - phy-mode = "rgmii"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - mdio { - compatible = "realtek,smi-mdio", "dsa-mdio"; - #address-cells = <1>; - #size-cells = <0>; - - phy0: phy@0 { - reg = <0>; - interrupt-parent = <&switch_intc>; - interrupts = <0>; - }; - phy1: phy@1 { - reg = <1>; - interrupt-parent = <&switch_intc>; - interrupts = <1>; - }; - phy2: phy@2 { - reg = <2>; - interrupt-parent = <&switch_intc>; - interrupts = <2>; - }; - phy3: phy@3 { - reg = <3>; - interrupt-parent = <&switch_intc>; - interrupts = <3>; - }; - phy4: phy@4 { - reg = <4>; - interrupt-parent = <&switch_intc>; - interrupts = <12>; - }; - }; -}; - -An example for the RTL8365MB-VC: - -switch { - compatible = "realtek,rtl8365mb"; - mdc-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; - mdio-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; - - switch_intc: interrupt-controller { - interrupt-parent = <&gpio5>; - interrupts = <1 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #address-cells = <0>; - #interrupt-cells = <1>; - }; - - ports { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - port@0 { - reg = <0>; - label = "swp0"; - phy-handle = <ðphy0>; - }; - port@1 { - reg = <1>; - label = "swp1"; - phy-handle = <ðphy1>; - }; - port@2 { - reg = <2>; - label = "swp2"; - phy-handle = <ðphy2>; - }; - port@3 { - reg = <3>; - label = "swp3"; - phy-handle = <ðphy3>; - }; - port@6 { - reg = <6>; - label = "cpu"; - ethernet = <&fec1>; - phy-mode = "rgmii"; - tx-internal-delay-ps = <2000>; - rx-internal-delay-ps = <2000>; - - fixed-link { - speed = <1000>; - full-duplex; - pause; - }; - }; - }; - - mdio { - compatible = "realtek,smi-mdio"; - #address-cells = <1>; - #size-cells = <0>; - - ethphy0: phy@0 { - reg = <0>; - interrupt-parent = <&switch_intc>; - interrupts = <0>; - }; - ethphy1: phy@1 { - reg = <1>; - interrupt-parent = <&switch_intc>; - interrupts = <1>; - }; - ethphy2: phy@2 { - reg = <2>; - interrupt-parent = <&switch_intc>; - interrupts = <2>; - }; - ethphy3: phy@3 { - reg = <3>; - interrupt-parent = <&switch_intc>; - interrupts = <3>; - }; - }; -}; |