diff options
Diffstat (limited to 'Documentation/devicetree/bindings/gpio')
4 files changed, 91 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-altera.txt b/Documentation/devicetree/bindings/gpio/gpio-altera.txt new file mode 100644 index 000000000000..12f50149e1ed --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-altera.txt @@ -0,0 +1,43 @@ +Altera GPIO controller bindings + +Required properties: +- compatible: + - "altr,pio-1.0" +- reg: Physical base address and length of the controller's registers. +- #gpio-cells : Should be 2 + - The first cell is the gpio offset number. + - The second cell is reserved and is currently unused. +- gpio-controller : Marks the device node as a GPIO controller. +- interrupt-controller: Mark the device node as an interrupt controller +- #interrupt-cells : Should be 1. The interrupt type is fixed in the hardware. + - The first cell is the GPIO offset number within the GPIO controller. +- interrupts: Specify the interrupt. +- altr,interrupt-trigger: Specifies the interrupt trigger type the GPIO + hardware is synthesized. This field is required if the Altera GPIO controller + used has IRQ enabled as the interrupt type is not software controlled, + but hardware synthesized. Required if GPIO is used as an interrupt + controller. The value is defined in <dt-bindings/interrupt-controller/irq.h> + Only the following flags are supported: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + IRQ_TYPE_LEVEL_HIGH + +Optional properties: +- altr,ngpio: Width of the GPIO bank. This defines how many pins the + GPIO device has. Ranges between 1-32. Optional and defaults to 32 if not + specified. + +Example: + +gpio_altr: gpio@0xff200000 { + compatible = "altr,pio-1.0"; + reg = <0xff200000 0x10>; + interrupts = <0 45 4>; + altr,ngpio = <32>; + altr,interrupt-trigger = <IRQ_TYPE_EDGE_RISING>; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <1>; + interrupt-controller; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-fan.txt b/Documentation/devicetree/bindings/gpio/gpio-fan.txt index 2dd457a3469a..439a7430fc68 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-fan.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-fan.txt @@ -2,15 +2,20 @@ Bindings for fan connected to GPIO lines Required properties: - compatible : "gpio-fan" + +Optional properties: - gpios: Specifies the pins that map to bits in the control value, ordered MSB-->LSB. - gpio-fan,speed-map: A mapping of possible fan RPM speeds and the control value that should be set to achieve them. This array must have the RPM values in ascending order. - -Optional properties: - alarm-gpios: This pin going active indicates something is wrong with the fan, and a udev event will be fired. +- cooling-cells: If used as a cooling device, must be <2> + Also see: Documentation/devicetree/bindings/thermal/thermal.txt + min and max states are derived from the speed-map of the fan. + +Note: At least one the "gpios" or "alarm-gpios" properties must be set. Examples: @@ -23,3 +28,13 @@ Examples: 6000 2>; alarm-gpios = <&gpio1 15 1>; }; + gpio_fan_cool: gpio_fan { + compatible = "gpio-fan"; + gpios = <&gpio2 14 1 + &gpio2 13 1>; + gpio-fan,speed-map = <0 0>, + <3000 1>, + <6000 2>; + alarm-gpios = <&gpio2 15 1>; + #cooling-cells = <2>; /* min followed by max */ + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index f7a158d85862..5788d5cf1252 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -116,6 +116,29 @@ Every GPIO controller node must contain both an empty "gpio-controller" property, and a #gpio-cells integer property, which indicates the number of cells in a gpio-specifier. +The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism +providing automatic GPIO request and configuration as part of the +gpio-controller's driver probe function. + +Each GPIO hog definition is represented as a child node of the GPIO controller. +Required properties: +- gpio-hog: A property specifying that this child node represent a GPIO hog. +- gpios: Store the GPIO information (id, flags, ...). Shall contain the + number of cells specified in its parent node (GPIO controller + node). +Only one of the following properties scanned in the order shown below. +This means that when multiple properties are present they will be searched +in the order presented below and the first match is taken as the intended +configuration. +- input: A property specifying to set the GPIO direction as input. +- output-low A property specifying to set the GPIO direction as output with + the value low. +- output-high A property specifying to set the GPIO direction as output with + the value high. + +Optional properties: +- line-name: The GPIO label name. If not present the node name is used. + Example of two SOC GPIO banks defined as gpio-controller nodes: qe_pio_a: gpio-controller@1400 { @@ -123,6 +146,13 @@ Example of two SOC GPIO banks defined as gpio-controller nodes: reg = <0x1400 0x18>; gpio-controller; #gpio-cells = <2>; + + line_b { + gpio-hog; + gpios = <6 0>; + output-low; + line-name = "foo-bar-gpio"; + }; }; qe_pio_e: gpio-controller@1460 { diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt index 67a2e4e414a5..98d198396956 100644 --- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt @@ -12,7 +12,7 @@ Required properties: gpio_mux. - interrupt-names : Should be the names of irq resources. Each interrupt uses its own interrupt name, so there should be as many interrupt names - as referenced interrups. + as referenced interrupts. - interrupt-controller : Identifies the node as an interrupt controller. - #interrupt-cells: Specifies the number of cells needed to encode an interrupt source. |