Merge tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci

Pull PCI updates from Bjorn Helgaas:
 "Enumeration:

   - Rework portdrv shutdown so it disables interrupts but doesn't
     disable bus mastering, which leads to hangs on Loongson LS7A

   - Add mechanism to prevent Max_Read_Request_Size (MRRS) increases,
     again to avoid hardware issues on Loongson LS7A (and likely other
     devices based on DesignWare IP)

   - Ignore devices with a firmware (DT or ACPI) node that says the
     device is disabled

  Resource management:

   - Distribute spare resources to unconfigured hotplug bridges at
     boot-time (not just when hot-adding such a bridge), which makes
     hot-adding devices to docks work better. Tried this in v6.1 but had
     to revert for regressions, so try again

   - Fix root bus issue that dropped resources that happened to end
     at 0, e.g., [bus 00]

  PCI device hotplug:

   - Remove device locking when marking device as disconnected so this
     doesn't have to wait for concurrent driver bind/unbind to complete

   - Quirk more Qualcomm bridges that don't fully implement the PCIe
     Slot Status 'Command Completed' bit

  Power management:

   - Account for _S0W of the target bridge in acpi_pci_bridge_d3() so we
     don't miss hot-add notifications for USB4 docks, Thunderbolt, etc

  Reset:

   - Observe delay after reset, e.g., resuming from system sleep,
     regardless of whether a bridge can suspend to D3cold at runtime

   - Wait for secondary bus to become ready after a bridge reset

  Virtualization:

   - Avoid FLR on some AMD FCH AHCI adapters where it doesn't work

   - Allow independent IOMMU groups for some Wangxun NICs that prevent
     peer-to-peer transactions but don't advertise an ACS Capability

  Error handling:

   - Configure End-to-End-CRC (ECRC) only if Linux owns the AER
     Capability

   - Remove redundant Device Control Error Reporting Enable in the AER
     service driver since this is already done for all devices during
     enumeration

  ASPM:

   - Add pci_enable_link_state() interface to allow drivers to enable
     ASPM link state

  Endpoint framework:

   - Move dra7xx and tegra194 linkup processing from hard IRQ to
     threaded IRQ handler

   - Add a separate lock for endpoint controller list of endpoint
     function drivers to prevent deadlock in callbacks

   - Pass events from endpoint controller to endpoint function drivers
     via callbacks instead of notifiers

  Synopsys DesignWare eDMA controller driver (acked by Vinod):

   - Fix CPU vs PCI address issues

   - Fix source vs destination address issues

   - Fix issues with interleaved transfer semantics

   - Fix channel count initialization issue (issue still exists in
     several other drivers)

   - Clean up and improve debugfs usage so it will work on platforms
     with several eDMA devices

  Baikal T-1 PCIe controller driver:

   - Set a 64-bit DMA mask

  Freescale i.MX6 PCIe controller driver:

   - Add i.MX8MM, i.MX8MQ, i.MX8MP endpoint mode DT binding and driver
     support

  Intel VMD host bridge driver:

   - Add quirk to configure PCIe ASPM and LTR. This is normally done by
     BIOS, and will be for future products

  Marvell MVEBU PCIe controller driver:

   - Mark this driver as broken in Kconfig since bugs prevent its daily
     usage

  MediaTek MT7621 PCIe controller driver:

   - Delay PHY port initialization to improve boot reliability for ZBT
     WE1326, ZBT WF3526-P, and some Netgear models

  Qualcomm PCIe controller driver:

   - Add MSM8998 DT compatible string

   - Unify MSM8996 and MSM8998 clock orderings

   - Add SM8350 DT binding and driver support

   - Add IPQ8074 Gen3 DT binding and driver support

   - Correct qcom,perst-regs in DT binding

   - Add qcom_pcie_host_deinit() so the PHY is powered off and
     regulators and clocks are disabled on late host-init errors

  Socionext UniPhier Pro5 controller driver:

   - Clean up uniphier-ep reg, clocks, resets, and their names in DT
     binding

  Synopsys DesignWare PCIe controller driver:

   - Restrict coherent DMA mask to 32 bits for MSI, but allow controller
     drivers to set 64-bit streaming DMA mask

   - Add eDMA engine support in both Root Port and Endpoint controllers

  Miscellaneous:

   - Remove MODULE_LICENSE from boolean drivers so they don't look like
     modules so modprobe can complain about them"

* tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (86 commits)
  PCI: dwc: Add Root Port and Endpoint controller eDMA engine support
  PCI: bt1: Set 64-bit DMA mask
  PCI: dwc: Restrict only coherent DMA mask for MSI address allocation
  dmaengine: dw-edma: Prepare dw_edma_probe() for builtin callers
  dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it
  dmaengine: dw-edma: Add mem-mapped LL-entries support
  PCI: Remove MODULE_LICENSE so boolean drivers don't look like modules
  PCI: hv: Drop duplicate PCI_MSI dependency
  PCI/P2PDMA: Annotate RCU dereference
  PCI/sysfs: Constify struct kobj_type pci_slot_ktype
  PCI: hotplug: Allow marking devices as disconnected during bind/unbind
  PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
  PCI: qcom: Add IPQ8074 Gen3 port support
  dt-bindings: PCI: qcom: Add IPQ8074 Gen3 port
  dt-bindings: PCI: qcom: Sort compatibles alphabetically
  PCI: qcom: Fix host-init error handling
  PCI: qcom: Add SM8350 support
  dt-bindings: PCI: qcom: Add SM8350
  dt-bindings: PCI: qcom-ep: Correct qcom,perst-regs
  dt-bindings: PCI: qcom: Unify MSM8996 and MSM8998 clock order
  ...

7 files changed, 47 insertions, 20 deletions

diff --git a/include/acpi/acpi_bus.h b/include/acpi/acpi_bus.h
index e44be31115a6..0584e9f6e339 100644
--- a/include/acpi/acpi_bus.h
+++ b/include/acpi/acpi_bus.h
@@ -534,6 +534,7 @@ int acpi_bus_update_power(acpi_handle handle, int *state_p);
 int acpi_device_update_power(struct acpi_device *device, int *state_p);
 bool acpi_bus_power_manageable(acpi_handle handle);
 void acpi_dev_power_up_children_with_adr(struct acpi_device *adev);
+u8 acpi_dev_power_state_for_wake(struct acpi_device *adev);
 int acpi_device_power_add_dependent(struct acpi_device *adev,
 				    struct device *dev);
 void acpi_device_power_remove_dependent(struct acpi_device *adev,
diff --git a/include/linux/dma/edma.h b/include/linux/dma/edma.h
index 7d8062e9c544..d2638d9259dc 100644
--- a/include/linux/dma/edma.h
+++ b/include/linux/dma/edma.h
@@ -18,13 +18,31 @@
 struct dw_edma;
 
 struct dw_edma_region {
-	phys_addr_t	paddr;
-	void __iomem	*vaddr;
+	u64		paddr;
+	union {
+		void		*mem;
+		void __iomem	*io;
+	} vaddr;
 	size_t		sz;
 };
 
+/**
+ * struct dw_edma_core_ops - platform-specific eDMA methods
+ * @irq_vector:		Get IRQ number of the passed eDMA channel. Note the
+ *			method accepts the channel id in the end-to-end
+ *			numbering with the eDMA write channels being placed
+ *			first in the row.
+ * @pci_address:	Get PCIe bus address corresponding to the passed CPU
+ *			address. Note there is no need in specifying this
+ *			function if the address translation is performed by
+ *			the DW PCIe RP/EP controller with the DW eDMA device in
+ *			subject and DMA_BYPASS isn't set for all the outbound
+ *			iATU windows. That will be done by the controller
+ *			automatically.
+ */
 struct dw_edma_core_ops {
 	int (*irq_vector)(struct device *dev, unsigned int nr);
+	u64 (*pci_address)(struct device *dev, phys_addr_t cpu_addr);
 };
 
 enum dw_edma_map_format {
@@ -61,7 +79,6 @@ enum dw_edma_chip_flags {
  */
 struct dw_edma_chip {
 	struct device		*dev;
-	int			id;
 	int			nr_irqs;
 	const struct dw_edma_core_ops   *ops;
 	u32			flags;
@@ -84,7 +101,7 @@ struct dw_edma_chip {
 };
 
 /* Export to the platform drivers */
-#if IS_ENABLED(CONFIG_DW_EDMA)
+#if IS_REACHABLE(CONFIG_DW_EDMA)
 int dw_edma_probe(struct dw_edma_chip *chip);
 int dw_edma_remove(struct dw_edma_chip *chip);
 #else
diff --git a/include/linux/dmaengine.h b/include/linux/dmaengine.h
index c923f4e60f24..0c020682d894 100644
--- a/include/linux/dmaengine.h
+++ b/include/linux/dmaengine.h
@@ -394,7 +394,7 @@ enum dma_slave_buswidth {
  * should be read (RX), if the source is memory this argument is
  * ignored.
  * @dst_addr: this is the physical address where DMA slave data
- * should be written (TX), if the source is memory this argument
+ * should be written (TX), if the destination is memory this argument
  * is ignored.
  * @src_addr_width: this is the width in bytes of the source (RX)
  * register where DMA data shall be read. If the source
diff --git a/include/linux/pci-epc.h b/include/linux/pci-epc.h
index a48778e1a4ee..301bb0e53707 100644
--- a/include/linux/pci-epc.h
+++ b/include/linux/pci-epc.h
@@ -122,6 +122,7 @@ struct pci_epc_mem {
  * struct pci_epc - represents the PCI EPC device
  * @dev: PCI EPC device
  * @pci_epf: list of endpoint functions present in this EPC device
+ * list_lock: Mutex for protecting pci_epf list
  * @ops: function pointers for performing endpoint operations
  * @windows: array of address space of the endpoint controller
  * @mem: first window of the endpoint controller, which corresponds to
@@ -134,11 +135,11 @@ struct pci_epc_mem {
  * @group: configfs group representing the PCI EPC device
  * @lock: mutex to protect pci_epc ops
  * @function_num_map: bitmap to manage physical function number
- * @notifier: used to notify EPF of any EPC events (like linkup)
  */
 struct pci_epc {
 	struct device			dev;
 	struct list_head		pci_epf;
+	struct mutex			list_lock;
 	const struct pci_epc_ops	*ops;
 	struct pci_epc_mem		**windows;
 	struct pci_epc_mem		*mem;
@@ -149,7 +150,6 @@ struct pci_epc {
 	/* mutex to protect against concurrent access of EP controller */
 	struct mutex			lock;
 	unsigned long			function_num_map;
-	struct atomic_notifier_head	notifier;
 };
 
 /**
@@ -192,12 +192,6 @@ static inline void *epc_get_drvdata(struct pci_epc *epc)
 	return dev_get_drvdata(&epc->dev);
 }
 
-static inline int
-pci_epc_register_notifier(struct pci_epc *epc, struct notifier_block *nb)
-{
-	return atomic_notifier_chain_register(&epc->notifier, nb);
-}
-
 struct pci_epc *
 __devm_pci_epc_create(struct device *dev, const struct pci_epc_ops *ops,
 		      struct module *owner);
diff --git a/include/linux/pci-epf.h b/include/linux/pci-epf.h
index 009a07147c61..a215dc8ce693 100644
--- a/include/linux/pci-epf.h
+++ b/include/linux/pci-epf.h
@@ -17,11 +17,6 @@
 struct pci_epf;
 enum pci_epc_interface_type;
 
-enum pci_notify_event {
-	CORE_INIT,
-	LINK_UP,
-};
-
 enum pci_barno {
 	NO_BAR = -1,
 	BAR_0,
@@ -73,6 +68,16 @@ struct pci_epf_ops {
 };
 
 /**
+ * struct pci_epf_event_ops - Callbacks for capturing the EPC events
+ * @core_init: Callback for the EPC initialization complete event
+ * @link_up: Callback for the EPC link up event
+ */
+struct pci_epc_event_ops {
+	int (*core_init)(struct pci_epf *epf);
+	int (*link_up)(struct pci_epf *epf);
+};
+
+/**
  * struct pci_epf_driver - represents the PCI EPF driver
  * @probe: ops to perform when a new EPF device has been bound to the EPF driver
  * @remove: ops to perform when the binding between the EPF device and EPF
@@ -127,7 +132,6 @@ struct pci_epf_bar {
  * @epf_pf: the physical EPF device to which this virtual EPF device is bound
  * @driver: the EPF driver to which this EPF device is bound
  * @list: to add pci_epf as a list of PCI endpoint functions to pci_epc
- * @nb: notifier block to notify EPF of any EPC events (like linkup)
  * @lock: mutex to protect pci_epf_ops
  * @sec_epc: the secondary EPC device to which this EPF device is bound
  * @sec_epc_list: to add pci_epf as list of PCI endpoint functions to secondary
@@ -139,6 +143,7 @@ struct pci_epf_bar {
  * @is_vf: true - virtual function, false - physical function
  * @vfunction_num_map: bitmap to manage virtual function number
  * @pci_vepf: list of virtual endpoint functions associated with this function
+ * @event_ops: Callbacks for capturing the EPC events
  */
 struct pci_epf {
 	struct device		dev;
@@ -154,7 +159,6 @@ struct pci_epf {
 	struct pci_epf		*epf_pf;
 	struct pci_epf_driver	*driver;
 	struct list_head	list;
-	struct notifier_block   nb;
 	/* mutex to protect against concurrent access of pci_epf_ops */
 	struct mutex		lock;
 
@@ -168,6 +172,7 @@ struct pci_epf {
 	unsigned int		is_vf;
 	unsigned long		vfunction_num_map;
 	struct list_head	pci_vepf;
+	const struct pci_epc_event_ops *event_ops;
 };
 
 /**
diff --git a/include/linux/pci.h b/include/linux/pci.h
index 254c8a4126a8..5f6fc5358b3c 100644
--- a/include/linux/pci.h
+++ b/include/linux/pci.h
@@ -572,6 +572,7 @@ struct pci_host_bridge {
 	void		*release_data;
 	unsigned int	ignore_reset_delay:1;	/* For entire hierarchy */
 	unsigned int	no_ext_tags:1;		/* No Extended Tags */
+	unsigned int	no_inc_mrrs:1;		/* No Increase MRRS */
 	unsigned int	native_aer:1;		/* OS may use PCIe AER */
 	unsigned int	native_pcie_hotplug:1;	/* OS may use PCIe hotplug */
 	unsigned int	native_shpc_hotplug:1;	/* OS may use SHPC hotplug */
@@ -1697,10 +1698,15 @@ extern bool pcie_ports_native;
 #define PCIE_LINK_STATE_L1_2		BIT(4)
 #define PCIE_LINK_STATE_L1_1_PCIPM	BIT(5)
 #define PCIE_LINK_STATE_L1_2_PCIPM	BIT(6)
+#define PCIE_LINK_STATE_ALL		(PCIE_LINK_STATE_L0S | PCIE_LINK_STATE_L1 |\
+					 PCIE_LINK_STATE_CLKPM | PCIE_LINK_STATE_L1_1 |\
+					 PCIE_LINK_STATE_L1_2 | PCIE_LINK_STATE_L1_1_PCIPM |\
+					 PCIE_LINK_STATE_L1_2_PCIPM)
 
 #ifdef CONFIG_PCIEASPM
 int pci_disable_link_state(struct pci_dev *pdev, int state);
 int pci_disable_link_state_locked(struct pci_dev *pdev, int state);
+int pci_enable_link_state(struct pci_dev *pdev, int state);
 void pcie_no_aspm(void);
 bool pcie_aspm_support_enabled(void);
 bool pcie_aspm_enabled(struct pci_dev *pdev);
@@ -1709,6 +1715,8 @@ static inline int pci_disable_link_state(struct pci_dev *pdev, int state)
 { return 0; }
 static inline int pci_disable_link_state_locked(struct pci_dev *pdev, int state)
 { return 0; }
+static inline int pci_enable_link_state(struct pci_dev *pdev, int state)
+{ return 0; }
 static inline void pcie_no_aspm(void) { }
 static inline bool pcie_aspm_support_enabled(void) { return false; }
 static inline bool pcie_aspm_enabled(struct pci_dev *pdev) { return false; }
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index b362d90eb9b0..bc8f484cdcf3 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -3012,6 +3012,8 @@
 #define PCI_DEVICE_ID_INTEL_VMD_9A0B	0x9a0b
 #define PCI_DEVICE_ID_INTEL_S21152BB	0xb152
 
+#define PCI_VENDOR_ID_WANGXUN		0x8088
+
 #define PCI_VENDOR_ID_SCALEMP		0x8686
 #define PCI_DEVICE_ID_SCALEMP_VSMP_CTL	0x1010