Merge branch 'devel-stable' into devel

Conflicts:
	MAINTAINERS
	arch/arm/mm/fault.c

1 files changed, 110 insertions, 38 deletions

diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index 8936eeb5588b..d31d32206ba3 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -25,6 +25,7 @@
 
 #include <linux/usb.h>
 #include <linux/timer.h>
+#include <linux/kernel.h>
 
 #include "../core/hcd.h"
 /* Code sharing between pci-quirks and xhci hcd */
@@ -42,14 +43,6 @@
  * xHCI register interface.
  * This corresponds to the eXtensible Host Controller Interface (xHCI)
  * Revision 0.95 specification
- *
- * Registers should always be accessed with double word or quad word accesses.
- *
- * Some xHCI implementations may support 64-bit address pointers.  Registers
- * with 64-bit address pointers should be written to with dword accesses by
- * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second.
- * xHCI implementations that do not support 64-bit address pointers will ignore
- * the high dword, and write order is irrelevant.
  */
 
 /**
@@ -96,6 +89,7 @@ struct xhci_cap_regs {
 #define HCS_ERST_MAX(p)		(((p) >> 4) & 0xf)
 /* bit 26 Scratchpad restore - for save/restore HW state - not used yet */
 /* bits 27:31 number of Scratchpad buffers SW must allocate for the HW */
+#define HCS_MAX_SCRATCHPAD(p)   (((p) >> 27) & 0x1f)
 
 /* HCSPARAMS3 - hcs_params3 - bitmasks */
 /* bits 0:7, Max U1 to U0 latency for the roothub ports */
@@ -166,10 +160,10 @@ struct xhci_op_regs {
 	u32	reserved1;
 	u32	reserved2;
 	u32	dev_notification;
-	u32	cmd_ring[2];
+	u64	cmd_ring;
 	/* rsvd: offset 0x20-2F */
 	u32	reserved3[4];
-	u32	dcbaa_ptr[2];
+	u64	dcbaa_ptr;
 	u32	config_reg;
 	/* rsvd: offset 0x3C-3FF */
 	u32	reserved4[241];
@@ -254,7 +248,7 @@ struct xhci_op_regs {
 #define CMD_RING_RUNNING	(1 << 3)
 /* bits 4:5 reserved and should be preserved */
 /* Command Ring pointer - bit mask for the lower 32 bits. */
-#define CMD_RING_ADDR_MASK	(0xffffffc0)
+#define CMD_RING_RSVD_BITS	(0x3f)
 
 /* CONFIG - Configure Register - config_reg bitmasks */
 /* bits 0:7 - maximum number of device slots enabled (NumSlotsEn) */
@@ -382,8 +376,8 @@ struct xhci_intr_reg {
 	u32	irq_control;
 	u32	erst_size;
 	u32	rsvd;
-	u32	erst_base[2];
-	u32	erst_dequeue[2];
+	u64	erst_base;
+	u64	erst_dequeue;
 };
 
 /* irq_pending bitmasks */
@@ -453,6 +447,27 @@ struct xhci_doorbell_array {
 
 
 /**
+ * struct xhci_container_ctx
+ * @type: Type of context.  Used to calculated offsets to contained contexts.
+ * @size: Size of the context data
+ * @bytes: The raw context data given to HW
+ * @dma: dma address of the bytes
+ *
+ * Represents either a Device or Input context.  Holds a pointer to the raw
+ * memory used for the context (bytes) and dma address of it (dma).
+ */
+struct xhci_container_ctx {
+	unsigned type;
+#define XHCI_CTX_TYPE_DEVICE  0x1
+#define XHCI_CTX_TYPE_INPUT   0x2
+
+	int size;
+
+	u8 *bytes;
+	dma_addr_t dma;
+};
+
+/**
  * struct xhci_slot_ctx
  * @dev_info:	Route string, device speed, hub info, and last valid endpoint
  * @dev_info2:	Max exit latency for device number, root hub port number
@@ -538,7 +553,7 @@ struct xhci_slot_ctx {
 struct xhci_ep_ctx {
 	u32	ep_info;
 	u32	ep_info2;
-	u32	deq[2];
+	u64	deq;
 	u32	tx_info;
 	/* offset 0x14 - 0x1f reserved for HC internal use */
 	u32	reserved[3];
@@ -589,18 +604,16 @@ struct xhci_ep_ctx {
 
 
 /**
- * struct xhci_device_control
- * Input/Output context; see section 6.2.5.
+ * struct xhci_input_control_context
+ * Input control context; see section 6.2.5.
  *
  * @drop_context:	set the bit of the endpoint context you want to disable
  * @add_context:	set the bit of the endpoint context you want to enable
  */
-struct xhci_device_control {
+struct xhci_input_control_ctx {
 	u32	drop_flags;
 	u32	add_flags;
-	u32	rsvd[6];
-	struct xhci_slot_ctx	slot;
-	struct xhci_ep_ctx	ep[31];
+	u32	rsvd2[6];
 };
 
 /* drop context bitmasks */
@@ -608,7 +621,6 @@ struct xhci_device_control {
 /* add context bitmasks */
 #define	ADD_EP(x)	(0x1 << x)
 
-
 struct xhci_virt_device {
 	/*
 	 * Commands to the hardware are passed an "input context" that
@@ -618,11 +630,10 @@ struct xhci_virt_device {
 	 * track of input and output contexts separately because
 	 * these commands might fail and we don't trust the hardware.
 	 */
-	struct xhci_device_control	*out_ctx;
-	dma_addr_t			out_ctx_dma;
+	struct xhci_container_ctx       *out_ctx;
 	/* Used for addressing devices and configuration changes */
-	struct xhci_device_control	*in_ctx;
-	dma_addr_t			in_ctx_dma;
+	struct xhci_container_ctx       *in_ctx;
+
 	/* FIXME when stream support is added */
 	struct xhci_ring		*ep_rings[31];
 	/* Temporary storage in case the configure endpoint command fails and we
@@ -641,7 +652,7 @@ struct xhci_virt_device {
  */
 struct xhci_device_context_array {
 	/* 64-bit device addresses; we only write 32-bit addresses */
-	u32			dev_context_ptrs[2*MAX_HC_SLOTS];
+	u64			dev_context_ptrs[MAX_HC_SLOTS];
 	/* private xHCD pointers */
 	dma_addr_t	dma;
 };
@@ -654,7 +665,7 @@ struct xhci_device_context_array {
 
 struct xhci_stream_ctx {
 	/* 64-bit stream ring address, cycle state, and stream type */
-	u32	stream_ring[2];
+	u64	stream_ring;
 	/* offset 0x14 - 0x1f reserved for HC internal use */
 	u32	reserved[2];
 };
@@ -662,7 +673,7 @@ struct xhci_stream_ctx {
 
 struct xhci_transfer_event {
 	/* 64-bit buffer address, or immediate data */
-	u32	buffer[2];
+	u64	buffer;
 	u32	transfer_len;
 	/* This field is interpreted differently based on the type of TRB */
 	u32	flags;
@@ -744,7 +755,7 @@ struct xhci_transfer_event {
 
 struct xhci_link_trb {
 	/* 64-bit segment pointer*/
-	u32 segment_ptr[2];
+	u64 segment_ptr;
 	u32 intr_target;
 	u32 control;
 };
@@ -755,7 +766,7 @@ struct xhci_link_trb {
 /* Command completion event TRB */
 struct xhci_event_cmd {
 	/* Pointer to command TRB, or the value passed by the event data trb */
-	u32 cmd_trb[2];
+	u64 cmd_trb;
 	u32 status;
 	u32 flags;
 };
@@ -848,8 +859,8 @@ union xhci_trb {
 #define TRB_CONFIG_EP		12
 /* Evaluate Context Command */
 #define TRB_EVAL_CONTEXT	13
-/* Reset Transfer Ring Command */
-#define TRB_RESET_RING		14
+/* Reset Endpoint Command */
+#define TRB_RESET_EP		14
 /* Stop Transfer Ring Command */
 #define TRB_STOP_RING		15
 /* Set Transfer Ring Dequeue Pointer Command */
@@ -929,6 +940,7 @@ struct xhci_ring {
 	unsigned int		cancels_pending;
 	unsigned int		state;
 #define SET_DEQ_PENDING		(1 << 0)
+#define EP_HALTED		(1 << 1)
 	/* The TRB that was last reported in a stopped endpoint ring */
 	union xhci_trb		*stopped_trb;
 	struct xhci_td		*stopped_td;
@@ -940,9 +952,15 @@ struct xhci_ring {
 	u32			cycle_state;
 };
 
+struct xhci_dequeue_state {
+	struct xhci_segment *new_deq_seg;
+	union xhci_trb *new_deq_ptr;
+	int new_cycle_state;
+};
+
 struct xhci_erst_entry {
 	/* 64-bit event ring segment address */
-	u32	seg_addr[2];
+	u64	seg_addr;
 	u32	seg_size;
 	/* Set to zero */
 	u32	rsvd;
@@ -957,6 +975,13 @@ struct xhci_erst {
 	unsigned int		erst_size;
 };
 
+struct xhci_scratchpad {
+	u64 *sp_array;
+	dma_addr_t sp_dma;
+	void **sp_buffers;
+	dma_addr_t *sp_dma_buffers;
+};
+
 /*
  * Each segment table entry is 4*32bits long.  1K seems like an ok size:
  * (1K bytes * 8bytes/bit) / (4*32 bits) = 64 segment entries in the table,
@@ -1011,6 +1036,9 @@ struct xhci_hcd {
 	struct xhci_ring	*cmd_ring;
 	struct xhci_ring	*event_ring;
 	struct xhci_erst	erst;
+	/* Scratchpad */
+	struct xhci_scratchpad  *scratchpad;
+
 	/* slot enabling and address device helpers */
 	struct completion	addr_dev;
 	int slot_id;
@@ -1071,13 +1099,43 @@ static inline unsigned int xhci_readl(const struct xhci_hcd *xhci,
 static inline void xhci_writel(struct xhci_hcd *xhci,
 		const unsigned int val, __u32 __iomem *regs)
 {
-	if (!in_interrupt())
-		xhci_dbg(xhci,
-			 "`MEM_WRITE_DWORD(3'b000, 32'h%p, 32'h%0x, 4'hf);\n",
-			 regs, val);
+	xhci_dbg(xhci,
+			"`MEM_WRITE_DWORD(3'b000, 32'h%p, 32'h%0x, 4'hf);\n",
+			regs, val);
 	writel(val, regs);
 }
 
+/*
+ * Registers should always be accessed with double word or quad word accesses.
+ *
+ * Some xHCI implementations may support 64-bit address pointers.  Registers
+ * with 64-bit address pointers should be written to with dword accesses by
+ * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second.
+ * xHCI implementations that do not support 64-bit address pointers will ignore
+ * the high dword, and write order is irrelevant.
+ */
+static inline u64 xhci_read_64(const struct xhci_hcd *xhci,
+		__u64 __iomem *regs)
+{
+	__u32 __iomem *ptr = (__u32 __iomem *) regs;
+	u64 val_lo = readl(ptr);
+	u64 val_hi = readl(ptr + 1);
+	return val_lo + (val_hi << 32);
+}
+static inline void xhci_write_64(struct xhci_hcd *xhci,
+		const u64 val, __u64 __iomem *regs)
+{
+	__u32 __iomem *ptr = (__u32 __iomem *) regs;
+	u32 val_lo = lower_32_bits(val);
+	u32 val_hi = upper_32_bits(val);
+
+	xhci_dbg(xhci,
+			"`MEM_WRITE_DWORD(3'b000, 64'h%p, 64'h%0lx, 4'hf);\n",
+			regs, (long unsigned int) val);
+	writel(val_lo, ptr);
+	writel(val_hi, ptr + 1);
+}
+
 /* xHCI debugging */
 void xhci_print_ir_set(struct xhci_hcd *xhci, struct xhci_intr_reg *ir_set, int set_num);
 void xhci_print_registers(struct xhci_hcd *xhci);
@@ -1090,7 +1148,7 @@ void xhci_debug_ring(struct xhci_hcd *xhci, struct xhci_ring *ring);
 void xhci_dbg_erst(struct xhci_hcd *xhci, struct xhci_erst *erst);
 void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci);
 void xhci_dbg_ring_ptrs(struct xhci_hcd *xhci, struct xhci_ring *ring);
-void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep);
+void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx, unsigned int last_ep);
 
 /* xHCI memory managment */
 void xhci_mem_cleanup(struct xhci_hcd *xhci);
@@ -1128,6 +1186,7 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags);
 int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status);
 int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep);
 int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep);
+void xhci_endpoint_reset(struct usb_hcd *hcd, struct usb_host_endpoint *ep);
 int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 
@@ -1148,10 +1207,23 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct urb *urb,
 		int slot_id, unsigned int ep_index);
 int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
 		u32 slot_id);
+int xhci_queue_reset_ep(struct xhci_hcd *xhci, int slot_id,
+		unsigned int ep_index);
+void xhci_find_new_dequeue_state(struct xhci_hcd *xhci,
+		unsigned int slot_id, unsigned int ep_index,
+		struct xhci_td *cur_td, struct xhci_dequeue_state *state);
+void xhci_queue_new_dequeue_state(struct xhci_hcd *xhci,
+		struct xhci_ring *ep_ring, unsigned int slot_id,
+		unsigned int ep_index, struct xhci_dequeue_state *deq_state);
 
 /* xHCI roothub code */
 int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex,
 		char *buf, u16 wLength);
 int xhci_hub_status_data(struct usb_hcd *hcd, char *buf);
 
+/* xHCI contexts */
+struct xhci_input_control_ctx *xhci_get_input_control_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx);
+struct xhci_slot_ctx *xhci_get_slot_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx);
+struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx, unsigned int ep_index);
+
 #endif /* __LINUX_XHCI_HCD_H */