Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking changes from David Miller:

 1) Get rid of the error prone NLA_PUT*() macros that used an embedded
    goto.

 2) Kill off the token-ring and MCA networking drivers, from Paul
    Gortmaker.

 3) Reduce high-order allocations made by datagram AF_UNIX sockets, from
    Eric Dumazet.

 4) Add PTP hardware clock support to IGB and IXGBE, from Richard
    Cochran and Jacob Keller.

 5) Allow users to query timestamping capabilities of a card via
    ethtool, from Richard Cochran.

 6) Add loadbalance mode to the teaming driver, from Jiri Pirko.  Part
    of this is that we can now have BPF filters not attached to sockets,
    and the loadbalancing function is calculated using one.

 7) Francois Romieu went through the network drivers removing gratuitous
    uses of netdev->base_addr, perhaps some day we can remove it
    completely but it's used for ISA probing still.

 8) Add a BPF JIT for sparc.  I know, who cares, right? :-)

 9) Move networking sysctl registry away from using the compatability
    mode interfaces in the sysctl code.  From Eric W Biederman.

10) Pavel Emelyanov added a way to save and restore TCP socket state via
    TCP_REPAIR, TCP_REPAIR_QUEUE, and TCP_QUEUE_SEQ socket options as
    well as a way to forcefully bind a socket to a port via the
    sk->sk_reuse value SK_FORCE_REUSE.  There is also a
    TCP_REPAIR_OPTIONS which allows to reinstante the TCP options
    enabled on the connection.

11) Several enhancements from Eric Dumazet that, in particular, can
    enhance splice performance on TCP sockets significantly.

     a) Reset the offset of the per-socket sendmsg page when we know
        we're the only use of the page in linear_to_page().

     b) Add facilities such that skb->data can be backed a page rather
        than SLAB kmalloc'd memory.  In particular devices which were
        receiving into linear RX buffers can now end up providing paged
        data.

    The big result is that code like splice and GRO do not have to copy
    any more.

12) Allow a pure sender to more gracefully handle ACK backlogs in TCP.
    What can happen at high rates is that the sender hasn't grown his
    receive buffer limits at all (he's not receiving data so really
    doesn't need to), but the non-data ACKs consume receive buffer
    space.

    sk_add_backlog() is too aggressive in dropping frames in this case,
    so relax it's requirements by using the receive buffer plus the send
    buffer limit as the backlog limit instead of just the former.

    Also from Eric Dumazet.

13) Add ipv6 support to L2TP, from Benjamin LaHaise, James Chapman, and
    Chris Elston.

14) Implement TCP early retransmit (RFC 5827), from Yuchung Cheng.
    Basically, we can start fast retransmit before hiting the dupack
    threshold under certain conditions.

15) New CODEL active queue management packet scheduler, from Eric
    Dumazet based upon initial work by Dave Taht.

    Basically, the big feature is that packets are dropped (or ECN bits
    are set) based upon how long packets live in the queue, rather than
    the queue length (which is what RED uses).

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1341 commits)
  drivers/net/stmmac: seq_file fix memory leak
  ipv6/exthdrs: strict Pad1 and PadN check
  USB: qmi_wwan: Add ZTE (Vodafone) K3520-Z
  USB: qmi_wwan: Add ZTE (Vodafone) K3765-Z
  USB: qmi_wwan: Make forced int 4 whitelist generic
  net/ipv4: replace simple_strtoul with kstrtoul
  net/ipv4/ipconfig: neaten __setup placement
  net: qmi_wwan: Add Vodafone/Huawei K5005 support
  net: cdc_ether: Add ZTE WWAN matches before generic Ethernet
  ipv6: use skb coalescing in reassembly
  ipv4: use skb coalescing in defragmentation
  net: introduce skb_try_coalesce()
  net:ipv6:fixed space issues relating to operators.
  net:ipv6:fixed a trailing white space issue.
  ipv6: disable GSO on sockets hitting dst_allfrag
  tg3: use netdev_alloc_frag() API
  net: napi_frags_skb() is static
  ppp: avoid false drop_monitor false positives
  ipv6: bool/const conversions phase2
  ipx: Remove spurious NULL checking in ipx_ioctl().
  ...

10 files changed, 2491 insertions, 0 deletions

diff --git a/drivers/net/wireless/ti/wl12xx/Kconfig b/drivers/net/wireless/ti/wl12xx/Kconfig
new file mode 100644
index 000000000000..5b92329122c4
--- /dev/null
+++ b/drivers/net/wireless/ti/wl12xx/Kconfig
@@ -0,0 +1,8 @@
+config WL12XX
+       tristate "TI wl12xx support"
+       select WLCORE
+       ---help---
+	  This module adds support for wireless adapters based on TI wl1271,
+	  wl1273, wl1281 and wl1283 chipsets. This module does *not* include
+	  support for wl1251.  For wl1251 support, use the separate homonymous
+	   driver instead.
diff --git a/drivers/net/wireless/ti/wl12xx/Makefile b/drivers/net/wireless/ti/wl12xx/Makefile
new file mode 100644
index 000000000000..87f64b14db35
--- /dev/null
+++ b/drivers/net/wireless/ti/wl12xx/Makefile
@@ -0,0 +1,3 @@
+wl12xx-objs	= main.o cmd.o acx.o
+
+obj-$(CONFIG_WL12XX)		+= wl12xx.o
diff --git a/drivers/net/wireless/ti/wl12xx/acx.c b/drivers/net/wireless/ti/wl12xx/acx.c
new file mode 100644
index 000000000000..bea06b2d7bf4
--- /dev/null
+++ b/drivers/net/wireless/ti/wl12xx/acx.c
@@ -0,0 +1,53 @@
+/*
+ * This file is part of wl12xx
+ *
+ * Copyright (C) 2008-2009 Nokia Corporation
+ * Copyright (C) 2011 Texas Instruments Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#include "../wlcore/cmd.h"
+#include "../wlcore/debug.h"
+#include "../wlcore/acx.h"
+
+#include "acx.h"
+
+int wl1271_acx_host_if_cfg_bitmap(struct wl1271 *wl, u32 host_cfg_bitmap)
+{
+	struct wl1271_acx_host_config_bitmap *bitmap_conf;
+	int ret;
+
+	bitmap_conf = kzalloc(sizeof(*bitmap_conf), GFP_KERNEL);
+	if (!bitmap_conf) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	bitmap_conf->host_cfg_bitmap = cpu_to_le32(host_cfg_bitmap);
+
+	ret = wl1271_cmd_configure(wl, ACX_HOST_IF_CFG_BITMAP,
+				   bitmap_conf, sizeof(*bitmap_conf));
+	if (ret < 0) {
+		wl1271_warning("wl1271 bitmap config opt failed: %d", ret);
+		goto out;
+	}
+
+out:
+	kfree(bitmap_conf);
+
+	return ret;
+}
diff --git a/drivers/net/wireless/ti/wl12xx/acx.h b/drivers/net/wireless/ti/wl12xx/acx.h
new file mode 100644
index 000000000000..d1f5aba0afce
--- /dev/null
+++ b/drivers/net/wireless/ti/wl12xx/acx.h
@@ -0,0 +1,36 @@
+/*
+ * This file is part of wl12xx
+ *
+ * Copyright (C) 1998-2009, 2011 Texas Instruments. All rights reserved.
+ * Copyright (C) 2008-2010 Nokia Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef __WL12XX_ACX_H__
+#define __WL12XX_ACX_H__
+
+#include "../wlcore/wlcore.h"
+
+struct wl1271_acx_host_config_bitmap {
+	struct acx_header header;
+
+	__le32 host_cfg_bitmap;
+} __packed;
+
+int wl1271_acx_host_if_cfg_bitmap(struct wl1271 *wl, u32 host_cfg_bitmap);
+
+#endif /* __WL12XX_ACX_H__ */
diff --git a/drivers/net/wireless/ti/wl12xx/cmd.c b/drivers/net/wireless/ti/wl12xx/cmd.c
new file mode 100644
index 000000000000..8ffaeb5f2147
--- /dev/null
+++ b/drivers/net/wireless/ti/wl12xx/cmd.c
@@ -0,0 +1,254 @@
+/*
+ * This file is part of wl12xx
+ *
+ * Copyright (C) 2009-2010 Nokia Corporation
+ * Copyright (C) 2011 Texas Instruments Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#include "../wlcore/cmd.h"
+#include "../wlcore/debug.h"
+
+#include "wl12xx.h"
+#include "cmd.h"
+
+int wl1271_cmd_ext_radio_parms(struct wl1271 *wl)
+{
+	struct wl1271_ext_radio_parms_cmd *ext_radio_parms;
+	struct wl12xx_priv *priv = wl->priv;
+	struct wl12xx_conf_rf *rf = &priv->conf.rf;
+	int ret;
+
+	if (!wl->nvs)
+		return -ENODEV;
+
+	ext_radio_parms = kzalloc(sizeof(*ext_radio_parms), GFP_KERNEL);
+	if (!ext_radio_parms)
+		return -ENOMEM;
+
+	ext_radio_parms->test.id = TEST_CMD_INI_FILE_RF_EXTENDED_PARAM;
+
+	memcpy(ext_radio_parms->tx_per_channel_power_compensation_2,
+	       rf->tx_per_channel_power_compensation_2,
+	       CONF_TX_PWR_COMPENSATION_LEN_2);
+	memcpy(ext_radio_parms->tx_per_channel_power_compensation_5,
+	       rf->tx_per_channel_power_compensation_5,
+	       CONF_TX_PWR_COMPENSATION_LEN_5);
+
+	wl1271_dump(DEBUG_CMD, "TEST_CMD_INI_FILE_EXT_RADIO_PARAM: ",
+		    ext_radio_parms, sizeof(*ext_radio_parms));
+
+	ret = wl1271_cmd_test(wl, ext_radio_parms, sizeof(*ext_radio_parms), 0);
+	if (ret < 0)
+		wl1271_warning("TEST_CMD_INI_FILE_RF_EXTENDED_PARAM failed");
+
+	kfree(ext_radio_parms);
+	return ret;
+}
+
+int wl1271_cmd_general_parms(struct wl1271 *wl)
+{
+	struct wl1271_general_parms_cmd *gen_parms;
+	struct wl1271_ini_general_params *gp =
+		&((struct wl1271_nvs_file *)wl->nvs)->general_params;
+	bool answer = false;
+	int ret;
+
+	if (!wl->nvs)
+		return -ENODEV;
+
+	if (gp->tx_bip_fem_manufacturer >= WL1271_INI_FEM_MODULE_COUNT) {
+		wl1271_warning("FEM index from INI out of bounds");
+		return -EINVAL;
+	}
+
+	gen_parms = kzalloc(sizeof(*gen_parms), GFP_KERNEL);
+	if (!gen_parms)
+		return -ENOMEM;
+
+	gen_parms->test.id = TEST_CMD_INI_FILE_GENERAL_PARAM;
+
+	memcpy(&gen_parms->general_params, gp, sizeof(*gp));
+
+	if (gp->tx_bip_fem_auto_detect)
+		answer = true;
+
+	/* Override the REF CLK from the NVS with the one from platform data */
+	gen_parms->general_params.ref_clock = wl->ref_clock;
+
+	ret = wl1271_cmd_test(wl, gen_parms, sizeof(*gen_parms), answer);
+	if (ret < 0) {
+		wl1271_warning("CMD_INI_FILE_GENERAL_PARAM failed");
+		goto out;
+	}
+
+	gp->tx_bip_fem_manufacturer =
+		gen_parms->general_params.tx_bip_fem_manufacturer;
+
+	if (gp->tx_bip_fem_manufacturer >= WL1271_INI_FEM_MODULE_COUNT) {
+		wl1271_warning("FEM index from FW out of bounds");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	wl1271_debug(DEBUG_CMD, "FEM autodetect: %s, manufacturer: %d\n",
+		     answer ? "auto" : "manual", gp->tx_bip_fem_manufacturer);
+
+out:
+	kfree(gen_parms);
+	return ret;
+}
+
+int wl128x_cmd_general_parms(struct wl1271 *wl)
+{
+	struct wl128x_general_parms_cmd *gen_parms;
+	struct wl128x_ini_general_params *gp =
+		&((struct wl128x_nvs_file *)wl->nvs)->general_params;
+	bool answer = false;
+	int ret;
+
+	if (!wl->nvs)
+		return -ENODEV;
+
+	if (gp->tx_bip_fem_manufacturer >= WL1271_INI_FEM_MODULE_COUNT) {
+		wl1271_warning("FEM index from ini out of bounds");
+		return -EINVAL;
+	}
+
+	gen_parms = kzalloc(sizeof(*gen_parms), GFP_KERNEL);
+	if (!gen_parms)
+		return -ENOMEM;
+
+	gen_parms->test.id = TEST_CMD_INI_FILE_GENERAL_PARAM;
+
+	memcpy(&gen_parms->general_params, gp, sizeof(*gp));
+
+	if (gp->tx_bip_fem_auto_detect)
+		answer = true;
+
+	/* Replace REF and TCXO CLKs with the ones from platform data */
+	gen_parms->general_params.ref_clock = wl->ref_clock;
+	gen_parms->general_params.tcxo_ref_clock = wl->tcxo_clock;
+
+	ret = wl1271_cmd_test(wl, gen_parms, sizeof(*gen_parms), answer);
+	if (ret < 0) {
+		wl1271_warning("CMD_INI_FILE_GENERAL_PARAM failed");
+		goto out;
+	}
+
+	gp->tx_bip_fem_manufacturer =
+		gen_parms->general_params.tx_bip_fem_manufacturer;
+
+	if (gp->tx_bip_fem_manufacturer >= WL1271_INI_FEM_MODULE_COUNT) {
+		wl1271_warning("FEM index from FW out of bounds");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	wl1271_debug(DEBUG_CMD, "FEM autodetect: %s, manufacturer: %d\n",
+		     answer ? "auto" : "manual", gp->tx_bip_fem_manufacturer);
+
+out:
+	kfree(gen_parms);
+	return ret;
+}
+
+int wl1271_cmd_radio_parms(struct wl1271 *wl)
+{
+	struct wl1271_nvs_file *nvs = (struct wl1271_nvs_file *)wl->nvs;
+	struct wl1271_radio_parms_cmd *radio_parms;
+	struct wl1271_ini_general_params *gp = &nvs->general_params;
+	int ret;
+
+	if (!wl->nvs)
+		return -ENODEV;
+
+	radio_parms = kzalloc(sizeof(*radio_parms), GFP_KERNEL);
+	if (!radio_parms)
+		return -ENOMEM;
+
+	radio_parms->test.id = TEST_CMD_INI_FILE_RADIO_PARAM;
+
+	/* 2.4GHz parameters */
+	memcpy(&radio_parms->static_params_2, &nvs->stat_radio_params_2,
+	       sizeof(struct wl1271_ini_band_params_2));
+	memcpy(&radio_parms->dyn_params_2,
+	       &nvs->dyn_radio_params_2[gp->tx_bip_fem_manufacturer].params,
+	       sizeof(struct wl1271_ini_fem_params_2));
+
+	/* 5GHz parameters */
+	memcpy(&radio_parms->static_params_5,
+	       &nvs->stat_radio_params_5,
+	       sizeof(struct wl1271_ini_band_params_5));
+	memcpy(&radio_parms->dyn_params_5,
+	       &nvs->dyn_radio_params_5[gp->tx_bip_fem_manufacturer].params,
+	       sizeof(struct wl1271_ini_fem_params_5));
+
+	wl1271_dump(DEBUG_CMD, "TEST_CMD_INI_FILE_RADIO_PARAM: ",
+		    radio_parms, sizeof(*radio_parms));
+
+	ret = wl1271_cmd_test(wl, radio_parms, sizeof(*radio_parms), 0);
+	if (ret < 0)
+		wl1271_warning("CMD_INI_FILE_RADIO_PARAM failed");
+
+	kfree(radio_parms);
+	return ret;
+}
+
+int wl128x_cmd_radio_parms(struct wl1271 *wl)
+{
+	struct wl128x_nvs_file *nvs = (struct wl128x_nvs_file *)wl->nvs;
+	struct wl128x_radio_parms_cmd *radio_parms;
+	struct wl128x_ini_general_params *gp = &nvs->general_params;
+	int ret;
+
+	if (!wl->nvs)
+		return -ENODEV;
+
+	radio_parms = kzalloc(sizeof(*radio_parms), GFP_KERNEL);
+	if (!radio_parms)
+		return -ENOMEM;
+
+	radio_parms->test.id = TEST_CMD_INI_FILE_RADIO_PARAM;
+
+	/* 2.4GHz parameters */
+	memcpy(&radio_parms->static_params_2, &nvs->stat_radio_params_2,
+	       sizeof(struct wl128x_ini_band_params_2));
+	memcpy(&radio_parms->dyn_params_2,
+	       &nvs->dyn_radio_params_2[gp->tx_bip_fem_manufacturer].params,
+	       sizeof(struct wl128x_ini_fem_params_2));
+
+	/* 5GHz parameters */
+	memcpy(&radio_parms->static_params_5,
+	       &nvs->stat_radio_params_5,
+	       sizeof(struct wl128x_ini_band_params_5));
+	memcpy(&radio_parms->dyn_params_5,
+	       &nvs->dyn_radio_params_5[gp->tx_bip_fem_manufacturer].params,
+	       sizeof(struct wl128x_ini_fem_params_5));
+
+	radio_parms->fem_vendor_and_options = nvs->fem_vendor_and_options;
+
+	wl1271_dump(DEBUG_CMD, "TEST_CMD_INI_FILE_RADIO_PARAM: ",
+		    radio_parms, sizeof(*radio_parms));
+
+	ret = wl1271_cmd_test(wl, radio_parms, sizeof(*radio_parms), 0);
+	if (ret < 0)
+		wl1271_warning("CMD_INI_FILE_RADIO_PARAM failed");
+
+	kfree(radio_parms);
+	return ret;
+}
diff --git a/drivers/net/wireless/ti/wl12xx/cmd.h b/drivers/net/wireless/ti/wl12xx/cmd.h
new file mode 100644
index 000000000000..140a0e8829d5
--- /dev/null
+++ b/drivers/net/wireless/ti/wl12xx/cmd.h
@@ -0,0 +1,112 @@
+/*
+ * This file is part of wl12xx
+ *
+ * Copyright (C) 1998-2009, 2011 Texas Instruments. All rights reserved.
+ * Copyright (C) 2009 Nokia Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef __WL12XX_CMD_H__
+#define __WL12XX_CMD_H__
+
+#include "conf.h"
+
+#define TEST_CMD_INI_FILE_RADIO_PARAM       0x19
+#define TEST_CMD_INI_FILE_GENERAL_PARAM     0x1E
+
+struct wl1271_general_parms_cmd {
+	struct wl1271_cmd_header header;
+
+	struct wl1271_cmd_test_header test;
+
+	struct wl1271_ini_general_params general_params;
+
+	u8 sr_debug_table[WL1271_INI_MAX_SMART_REFLEX_PARAM];
+	u8 sr_sen_n_p;
+	u8 sr_sen_n_p_gain;
+	u8 sr_sen_nrn;
+	u8 sr_sen_prn;
+	u8 padding[3];
+} __packed;
+
+struct wl128x_general_parms_cmd {
+	struct wl1271_cmd_header header;
+
+	struct wl1271_cmd_test_header test;
+
+	struct wl128x_ini_general_params general_params;
+
+	u8 sr_debug_table[WL1271_INI_MAX_SMART_REFLEX_PARAM];
+	u8 sr_sen_n_p;
+	u8 sr_sen_n_p_gain;
+	u8 sr_sen_nrn;
+	u8 sr_sen_prn;
+	u8 padding[3];
+} __packed;
+
+struct wl1271_radio_parms_cmd {
+	struct wl1271_cmd_header header;
+
+	struct wl1271_cmd_test_header test;
+
+	/* Static radio parameters */
+	struct wl1271_ini_band_params_2 static_params_2;
+	struct wl1271_ini_band_params_5 static_params_5;
+
+	/* Dynamic radio parameters */
+	struct wl1271_ini_fem_params_2 dyn_params_2;
+	u8 padding2;
+	struct wl1271_ini_fem_params_5 dyn_params_5;
+	u8 padding3[2];
+} __packed;
+
+struct wl128x_radio_parms_cmd {
+	struct wl1271_cmd_header header;
+
+	struct wl1271_cmd_test_header test;
+
+	/* Static radio parameters */
+	struct wl128x_ini_band_params_2 static_params_2;
+	struct wl128x_ini_band_params_5 static_params_5;
+
+	u8 fem_vendor_and_options;
+
+	/* Dynamic radio parameters */
+	struct wl128x_ini_fem_params_2 dyn_params_2;
+	u8 padding2;
+	struct wl128x_ini_fem_params_5 dyn_params_5;
+} __packed;
+
+#define TEST_CMD_INI_FILE_RF_EXTENDED_PARAM 0x26
+
+struct wl1271_ext_radio_parms_cmd {
+	struct wl1271_cmd_header header;
+
+	struct wl1271_cmd_test_header test;
+
+	u8 tx_per_channel_power_compensation_2[CONF_TX_PWR_COMPENSATION_LEN_2];
+	u8 tx_per_channel_power_compensation_5[CONF_TX_PWR_COMPENSATION_LEN_5];
+	u8 padding[3];
+} __packed;
+
+int wl1271_cmd_general_parms(struct wl1271 *wl);
+int wl128x_cmd_general_parms(struct wl1271 *wl);
+int wl1271_cmd_radio_parms(struct wl1271 *wl);
+int wl128x_cmd_radio_parms(struct wl1271 *wl);
+int wl1271_cmd_ext_radio_parms(struct wl1271 *wl);
+
+#endif /* __WL12XX_CMD_H__ */
diff --git a/drivers/net/wireless/ti/wl12xx/conf.h b/drivers/net/wireless/ti/wl12xx/conf.h
new file mode 100644
index 000000000000..75e29897a0f5
--- /dev/null
+++ b/drivers/net/wireless/ti/wl12xx/conf.h
@@ -0,0 +1,50 @@
+/*
+ * This file is part of wl12xx
+ *
+ * Copyright (C) 2011 Texas Instruments Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef __WL12XX_CONF_H__
+#define __WL12XX_CONF_H__
+
+/* these are number of channels on the band divided by two, rounded up */
+#define CONF_TX_PWR_COMPENSATION_LEN_2 7
+#define CONF_TX_PWR_COMPENSATION_LEN_5 18
+
+struct wl12xx_conf_rf {
+	/*
+	 * Per channel power compensation for 2.4GHz
+	 *
+	 * Range: s8
+	 */
+	u8 tx_per_channel_power_compensation_2[CONF_TX_PWR_COMPENSATION_LEN_2];
+
+	/*
+	 * Per channel power compensation for 5GHz
+	 *
+	 * Range: s8
+	 */
+	u8 tx_per_channel_power_compensation_5[CONF_TX_PWR_COMPENSATION_LEN_5];
+};
+
+struct wl12xx_priv_conf {
+	struct wl12xx_conf_rf rf;
+	struct conf_memory_settings mem_wl127x;
+};
+
+#endif /* __WL12XX_CONF_H__ */
diff --git a/drivers/net/wireless/ti/wl12xx/main.c b/drivers/net/wireless/ti/wl12xx/main.c
new file mode 100644
index 000000000000..d7dd3def07b5
--- /dev/null
+++ b/drivers/net/wireless/ti/wl12xx/main.c
@@ -0,0 +1,1388 @@
+/*
+ * This file is part of wl1271
+ *
+ * Copyright (C) 2008-2010 Nokia Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include <linux/err.h>
+
+#include <linux/wl12xx.h>
+
+#include "../wlcore/wlcore.h"
+#include "../wlcore/debug.h"
+#include "../wlcore/io.h"
+#include "../wlcore/acx.h"
+#include "../wlcore/tx.h"
+#include "../wlcore/rx.h"
+#include "../wlcore/io.h"
+#include "../wlcore/boot.h"
+
+#include "wl12xx.h"
+#include "reg.h"
+#include "cmd.h"
+#include "acx.h"
+
+static struct wlcore_conf wl12xx_conf = {
+	.sg = {
+		.params = {
+			[CONF_SG_ACL_BT_MASTER_MIN_BR] = 10,
+			[CONF_SG_ACL_BT_MASTER_MAX_BR] = 180,
+			[CONF_SG_ACL_BT_SLAVE_MIN_BR] = 10,
+			[CONF_SG_ACL_BT_SLAVE_MAX_BR] = 180,
+			[CONF_SG_ACL_BT_MASTER_MIN_EDR] = 10,
+			[CONF_SG_ACL_BT_MASTER_MAX_EDR] = 80,
+			[CONF_SG_ACL_BT_SLAVE_MIN_EDR] = 10,
+			[CONF_SG_ACL_BT_SLAVE_MAX_EDR] = 80,
+			[CONF_SG_ACL_WLAN_PS_MASTER_BR] = 8,
+			[CONF_SG_ACL_WLAN_PS_SLAVE_BR] = 8,
+			[CONF_SG_ACL_WLAN_PS_MASTER_EDR] = 20,
+			[CONF_SG_ACL_WLAN_PS_SLAVE_EDR] = 20,
+			[CONF_SG_ACL_WLAN_ACTIVE_MASTER_MIN_BR] = 20,
+			[CONF_SG_ACL_WLAN_ACTIVE_MASTER_MAX_BR] = 35,
+			[CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MIN_BR] = 16,
+			[CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MAX_BR] = 35,
+			[CONF_SG_ACL_WLAN_ACTIVE_MASTER_MIN_EDR] = 32,
+			[CONF_SG_ACL_WLAN_ACTIVE_MASTER_MAX_EDR] = 50,
+			[CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MIN_EDR] = 28,
+			[CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MAX_EDR] = 50,
+			[CONF_SG_ACL_ACTIVE_SCAN_WLAN_BR] = 10,
+			[CONF_SG_ACL_ACTIVE_SCAN_WLAN_EDR] = 20,
+			[CONF_SG_ACL_PASSIVE_SCAN_BT_BR] = 75,
+			[CONF_SG_ACL_PASSIVE_SCAN_WLAN_BR] = 15,
+			[CONF_SG_ACL_PASSIVE_SCAN_BT_EDR] = 27,
+			[CONF_SG_ACL_PASSIVE_SCAN_WLAN_EDR] = 17,
+			/* active scan params */
+			[CONF_SG_AUTO_SCAN_PROBE_REQ] = 170,
+			[CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_HV3] = 50,
+			[CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_A2DP] = 100,
+			/* passive scan params */
+			[CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_A2DP_BR] = 800,
+			[CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_A2DP_EDR] = 200,
+			[CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_HV3] = 200,
+			/* passive scan in dual antenna params */
+			[CONF_SG_CONSECUTIVE_HV3_IN_PASSIVE_SCAN] = 0,
+			[CONF_SG_BCN_HV3_COLLISION_THRESH_IN_PASSIVE_SCAN] = 0,
+			[CONF_SG_TX_RX_PROTECTION_BWIDTH_IN_PASSIVE_SCAN] = 0,
+			/* general params */
+			[CONF_SG_STA_FORCE_PS_IN_BT_SCO] = 1,
+			[CONF_SG_ANTENNA_CONFIGURATION] = 0,
+			[CONF_SG_BEACON_MISS_PERCENT] = 60,
+			[CONF_SG_DHCP_TIME] = 5000,
+			[CONF_SG_RXT] = 1200,
+			[CONF_SG_TXT] = 1000,
+			[CONF_SG_ADAPTIVE_RXT_TXT] = 1,
+			[CONF_SG_GENERAL_USAGE_BIT_MAP] = 3,
+			[CONF_SG_HV3_MAX_SERVED] = 6,
+			[CONF_SG_PS_POLL_TIMEOUT] = 10,
+			[CONF_SG_UPSD_TIMEOUT] = 10,
+			[CONF_SG_CONSECUTIVE_CTS_THRESHOLD] = 2,
+			[CONF_SG_STA_RX_WINDOW_AFTER_DTIM] = 5,
+			[CONF_SG_STA_CONNECTION_PROTECTION_TIME] = 30,
+			/* AP params */
+			[CONF_AP_BEACON_MISS_TX] = 3,
+			[CONF_AP_RX_WINDOW_AFTER_BEACON] = 10,
+			[CONF_AP_BEACON_WINDOW_INTERVAL] = 2,
+			[CONF_AP_CONNECTION_PROTECTION_TIME] = 0,
+			[CONF_AP_BT_ACL_VAL_BT_SERVE_TIME] = 25,
+			[CONF_AP_BT_ACL_VAL_WL_SERVE_TIME] = 25,
+			/* CTS Diluting params */
+			[CONF_SG_CTS_DILUTED_BAD_RX_PACKETS_TH] = 0,
+			[CONF_SG_CTS_CHOP_IN_DUAL_ANT_SCO_MASTER] = 0,
+		},
+		.state = CONF_SG_PROTECTIVE,
+	},
+	.rx = {
+		.rx_msdu_life_time           = 512000,
+		.packet_detection_threshold  = 0,
+		.ps_poll_timeout             = 15,
+		.upsd_timeout                = 15,
+		.rts_threshold               = IEEE80211_MAX_RTS_THRESHOLD,
+		.rx_cca_threshold            = 0,
+		.irq_blk_threshold           = 0xFFFF,
+		.irq_pkt_threshold           = 0,
+		.irq_timeout                 = 600,
+		.queue_type                  = CONF_RX_QUEUE_TYPE_LOW_PRIORITY,
+	},
+	.tx = {
+		.tx_energy_detection         = 0,
+		.sta_rc_conf                 = {
+			.enabled_rates       = 0,
+			.short_retry_limit   = 10,
+			.long_retry_limit    = 10,
+			.aflags              = 0,
+		},
+		.ac_conf_count               = 4,
+		.ac_conf                     = {
+			[CONF_TX_AC_BE] = {
+				.ac          = CONF_TX_AC_BE,
+				.cw_min      = 15,
+				.cw_max      = 63,
+				.aifsn       = 3,
+				.tx_op_limit = 0,
+			},
+			[CONF_TX_AC_BK] = {
+				.ac          = CONF_TX_AC_BK,
+				.cw_min      = 15,
+				.cw_max      = 63,
+				.aifsn       = 7,
+				.tx_op_limit = 0,
+			},
+			[CONF_TX_AC_VI] = {
+				.ac          = CONF_TX_AC_VI,
+				.cw_min      = 15,
+				.cw_max      = 63,
+				.aifsn       = CONF_TX_AIFS_PIFS,
+				.tx_op_limit = 3008,
+			},
+			[CONF_TX_AC_VO] = {
+				.ac          = CONF_TX_AC_VO,
+				.cw_min      = 15,
+				.cw_max      = 63,
+				.aifsn       = CONF_TX_AIFS_PIFS,
+				.tx_op_limit = 1504,
+			},
+		},
+		.max_tx_retries = 100,
+		.ap_aging_period = 300,
+		.tid_conf_count = 4,
+		.tid_conf = {
+			[CONF_TX_AC_BE] = {
+				.queue_id    = CONF_TX_AC_BE,
+				.channel_type = CONF_CHANNEL_TYPE_EDCF,
+				.tsid        = CONF_TX_AC_BE,
+				.ps_scheme   = CONF_PS_SCHEME_LEGACY,
+				.ack_policy  = CONF_ACK_POLICY_LEGACY,
+				.apsd_conf   = {0, 0},
+			},
+			[CONF_TX_AC_BK] = {
+				.queue_id    = CONF_TX_AC_BK,
+				.channel_type = CONF_CHANNEL_TYPE_EDCF,
+				.tsid        = CONF_TX_AC_BK,
+				.ps_scheme   = CONF_PS_SCHEME_LEGACY,
+				.ack_policy  = CONF_ACK_POLICY_LEGACY,
+				.apsd_conf   = {0, 0},
+			},
+			[CONF_TX_AC_VI] = {
+				.queue_id    = CONF_TX_AC_VI,
+				.channel_type = CONF_CHANNEL_TYPE_EDCF,
+				.tsid        = CONF_TX_AC_VI,
+				.ps_scheme   = CONF_PS_SCHEME_LEGACY,
+				.ack_policy  = CONF_ACK_POLICY_LEGACY,
+				.apsd_conf   = {0, 0},
+			},
+			[CONF_TX_AC_VO] = {
+				.queue_id    = CONF_TX_AC_VO,
+				.channel_type = CONF_CHANNEL_TYPE_EDCF,
+				.tsid        = CONF_TX_AC_VO,
+				.ps_scheme   = CONF_PS_SCHEME_LEGACY,
+				.ack_policy  = CONF_ACK_POLICY_LEGACY,
+				.apsd_conf   = {0, 0},
+			},
+		},
+		.frag_threshold              = IEEE80211_MAX_FRAG_THRESHOLD,
+		.tx_compl_timeout            = 700,
+		.tx_compl_threshold          = 4,
+		.basic_rate                  = CONF_HW_BIT_RATE_1MBPS,
+		.basic_rate_5                = CONF_HW_BIT_RATE_6MBPS,
+		.tmpl_short_retry_limit      = 10,
+		.tmpl_long_retry_limit       = 10,
+		.tx_watchdog_timeout         = 5000,
+	},
+	.conn = {
+		.wake_up_event               = CONF_WAKE_UP_EVENT_DTIM,
+		.listen_interval             = 1,
+		.suspend_wake_up_event       = CONF_WAKE_UP_EVENT_N_DTIM,
+		.suspend_listen_interval     = 3,
+		.bcn_filt_mode               = CONF_BCN_FILT_MODE_ENABLED,
+		.bcn_filt_ie_count           = 2,
+		.bcn_filt_ie = {
+			[0] = {
+				.ie          = WLAN_EID_CHANNEL_SWITCH,
+				.rule        = CONF_BCN_RULE_PASS_ON_APPEARANCE,
+			},
+			[1] = {
+				.ie          = WLAN_EID_HT_OPERATION,
+				.rule        = CONF_BCN_RULE_PASS_ON_CHANGE,
+			},
+		},
+		.synch_fail_thold            = 10,
+		.bss_lose_timeout            = 100,
+		.beacon_rx_timeout           = 10000,
+		.broadcast_timeout           = 20000,
+		.rx_broadcast_in_ps          = 1,
+		.ps_poll_threshold           = 10,
+		.bet_enable                  = CONF_BET_MODE_ENABLE,
+		.bet_max_consecutive         = 50,
+		.psm_entry_retries           = 8,
+		.psm_exit_retries            = 16,
+		.psm_entry_nullfunc_retries  = 3,
+		.dynamic_ps_timeout          = 40,
+		.forced_ps                   = false,
+		.keep_alive_interval         = 55000,
+		.max_listen_interval         = 20,
+	},
+	.itrim = {
+		.enable = false,
+		.timeout = 50000,
+	},
+	.pm_config = {
+		.host_clk_settling_time = 5000,
+		.host_fast_wakeup_support = false
+	},
+	.roam_trigger = {
+		.trigger_pacing               = 1,
+		.avg_weight_rssi_beacon       = 20,
+		.avg_weight_rssi_data         = 10,
+		.avg_weight_snr_beacon        = 20,
+		.avg_weight_snr_data          = 10,
+	},
+	.scan = {
+		.min_dwell_time_active        = 7500,
+		.max_dwell_time_active        = 30000,
+		.min_dwell_time_passive       = 100000,
+		.max_dwell_time_passive       = 100000,
+		.num_probe_reqs               = 2,
+		.split_scan_timeout           = 50000,
+	},
+	.sched_scan = {
+		/*
+		 * Values are in TU/1000 but since sched scan FW command
+		 * params are in TUs rounding up may occur.
+		 */
+		.base_dwell_time		= 7500,
+		.max_dwell_time_delta		= 22500,
+		/* based on 250bits per probe @1Mbps */
+		.dwell_time_delta_per_probe	= 2000,
+		/* based on 250bits per probe @6Mbps (plus a bit more) */
+		.dwell_time_delta_per_probe_5	= 350,
+		.dwell_time_passive		= 100000,
+		.dwell_time_dfs			= 150000,
+		.num_probe_reqs			= 2,
+		.rssi_threshold			= -90,
+		.snr_threshold			= 0,
+	},
+	.ht = {
+		.rx_ba_win_size = 8,
+		.tx_ba_win_size = 64,
+		.inactivity_timeout = 10000,
+		.tx_ba_tid_bitmap = CONF_TX_BA_ENABLED_TID_BITMAP,
+	},
+	/*
+	 * Memory config for wl127x chips is given in the
+	 * wl12xx_default_priv_conf struct. The below configuration is
+	 * for wl128x chips.
+	 */
+	.mem = {
+		.num_stations                 = 1,
+		.ssid_profiles                = 1,
+		.rx_block_num                 = 40,
+		.tx_min_block_num             = 40,
+		.dynamic_memory               = 1,
+		.min_req_tx_blocks            = 45,
+		.min_req_rx_blocks            = 22,
+		.tx_min                       = 27,
+	},
+	.fm_coex = {
+		.enable                       = true,
+		.swallow_period               = 5,
+		.n_divider_fref_set_1         = 0xff,       /* default */
+		.n_divider_fref_set_2         = 12,
+		.m_divider_fref_set_1         = 148,
+		.m_divider_fref_set_2         = 0xffff,     /* default */
+		.coex_pll_stabilization_time  = 0xffffffff, /* default */
+		.ldo_stabilization_time       = 0xffff,     /* default */
+		.fm_disturbed_band_margin     = 0xff,       /* default */
+		.swallow_clk_diff             = 0xff,       /* default */
+	},
+	.rx_streaming = {
+		.duration                      = 150,
+		.queues                        = 0x1,
+		.interval                      = 20,
+		.always                        = 0,
+	},
+	.fwlog = {
+		.mode                         = WL12XX_FWLOG_ON_DEMAND,
+		.mem_blocks                   = 2,
+		.severity                     = 0,
+		.timestamp                    = WL12XX_FWLOG_TIMESTAMP_DISABLED,
+		.output                       = WL12XX_FWLOG_OUTPUT_HOST,
+		.threshold                    = 0,
+	},
+	.rate = {
+		.rate_retry_score = 32000,
+		.per_add = 8192,
+		.per_th1 = 2048,
+		.per_th2 = 4096,
+		.max_per = 8100,
+		.inverse_curiosity_factor = 5,
+		.tx_fail_low_th = 4,
+		.tx_fail_high_th = 10,
+		.per_alpha_shift = 4,
+		.per_add_shift = 13,
+		.per_beta1_shift = 10,
+		.per_beta2_shift = 8,
+		.rate_check_up = 2,
+		.rate_check_down = 12,
+		.rate_retry_policy = {
+			0x00, 0x00, 0x00, 0x00, 0x00,
+			0x00, 0x00, 0x00, 0x00, 0x00,
+			0x00, 0x00, 0x00,
+		},
+	},
+	.hangover = {
+		.recover_time               = 0,
+		.hangover_period            = 20,
+		.dynamic_mode               = 1,
+		.early_termination_mode     = 1,
+		.max_period                 = 20,
+		.min_period                 = 1,
+		.increase_delta             = 1,
+		.decrease_delta             = 2,
+		.quiet_time                 = 4,
+		.increase_time              = 1,
+		.window_size                = 16,
+	},
+};
+
+static struct wl12xx_priv_conf wl12xx_default_priv_conf = {
+	.rf = {
+		.tx_per_channel_power_compensation_2 = {
+			0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+		},
+		.tx_per_channel_power_compensation_5 = {
+			0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+			0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+			0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+		},
+	},
+	.mem_wl127x = {
+		.num_stations                 = 1,
+		.ssid_profiles                = 1,
+		.rx_block_num                 = 70,
+		.tx_min_block_num             = 40,
+		.dynamic_memory               = 1,
+		.min_req_tx_blocks            = 100,
+		.min_req_rx_blocks            = 22,
+		.tx_min                       = 27,
+	},
+
+};
+
+#define WL12XX_TX_HW_BLOCK_SPARE_DEFAULT        1
+#define WL12XX_TX_HW_BLOCK_GEM_SPARE            2
+#define WL12XX_TX_HW_BLOCK_SIZE                 252
+
+static const u8 wl12xx_rate_to_idx_2ghz[] = {
+	/* MCS rates are used only with 11n */
+	7,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS7_SGI */
+	7,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS7 */
+	6,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS6 */
+	5,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS5 */
+	4,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS4 */
+	3,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS3 */
+	2,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS2 */
+	1,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS1 */
+	0,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS0 */
+
+	11,                            /* WL12XX_CONF_HW_RXTX_RATE_54   */
+	10,                            /* WL12XX_CONF_HW_RXTX_RATE_48   */
+	9,                             /* WL12XX_CONF_HW_RXTX_RATE_36   */
+	8,                             /* WL12XX_CONF_HW_RXTX_RATE_24   */
+
+	/* TI-specific rate */
+	CONF_HW_RXTX_RATE_UNSUPPORTED, /* WL12XX_CONF_HW_RXTX_RATE_22   */
+
+	7,                             /* WL12XX_CONF_HW_RXTX_RATE_18   */
+	6,                             /* WL12XX_CONF_HW_RXTX_RATE_12   */
+	3,                             /* WL12XX_CONF_HW_RXTX_RATE_11   */
+	5,                             /* WL12XX_CONF_HW_RXTX_RATE_9    */
+	4,                             /* WL12XX_CONF_HW_RXTX_RATE_6    */
+	2,                             /* WL12XX_CONF_HW_RXTX_RATE_5_5  */
+	1,                             /* WL12XX_CONF_HW_RXTX_RATE_2    */
+	0                              /* WL12XX_CONF_HW_RXTX_RATE_1    */
+};
+
+static const u8 wl12xx_rate_to_idx_5ghz[] = {
+	/* MCS rates are used only with 11n */
+	7,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS7_SGI */
+	7,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS7 */
+	6,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS6 */
+	5,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS5 */
+	4,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS4 */
+	3,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS3 */
+	2,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS2 */
+	1,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS1 */
+	0,                             /* WL12XX_CONF_HW_RXTX_RATE_MCS0 */
+
+	7,                             /* WL12XX_CONF_HW_RXTX_RATE_54   */
+	6,                             /* WL12XX_CONF_HW_RXTX_RATE_48   */
+	5,                             /* WL12XX_CONF_HW_RXTX_RATE_36   */
+	4,                             /* WL12XX_CONF_HW_RXTX_RATE_24   */
+
+	/* TI-specific rate */
+	CONF_HW_RXTX_RATE_UNSUPPORTED, /* WL12XX_CONF_HW_RXTX_RATE_22   */
+
+	3,                             /* WL12XX_CONF_HW_RXTX_RATE_18   */
+	2,                             /* WL12XX_CONF_HW_RXTX_RATE_12   */
+	CONF_HW_RXTX_RATE_UNSUPPORTED, /* WL12XX_CONF_HW_RXTX_RATE_11   */
+	1,                             /* WL12XX_CONF_HW_RXTX_RATE_9    */
+	0,                             /* WL12XX_CONF_HW_RXTX_RATE_6    */
+	CONF_HW_RXTX_RATE_UNSUPPORTED, /* WL12XX_CONF_HW_RXTX_RATE_5_5  */
+	CONF_HW_RXTX_RATE_UNSUPPORTED, /* WL12XX_CONF_HW_RXTX_RATE_2    */
+	CONF_HW_RXTX_RATE_UNSUPPORTED  /* WL12XX_CONF_HW_RXTX_RATE_1    */
+};
+
+static const u8 *wl12xx_band_rate_to_idx[] = {
+	[IEEE80211_BAND_2GHZ] = wl12xx_rate_to_idx_2ghz,
+	[IEEE80211_BAND_5GHZ] = wl12xx_rate_to_idx_5ghz
+};
+
+enum wl12xx_hw_rates {
+	WL12XX_CONF_HW_RXTX_RATE_MCS7_SGI = 0,
+	WL12XX_CONF_HW_RXTX_RATE_MCS7,
+	WL12XX_CONF_HW_RXTX_RATE_MCS6,
+	WL12XX_CONF_HW_RXTX_RATE_MCS5,
+	WL12XX_CONF_HW_RXTX_RATE_MCS4,
+	WL12XX_CONF_HW_RXTX_RATE_MCS3,
+	WL12XX_CONF_HW_RXTX_RATE_MCS2,
+	WL12XX_CONF_HW_RXTX_RATE_MCS1,
+	WL12XX_CONF_HW_RXTX_RATE_MCS0,
+	WL12XX_CONF_HW_RXTX_RATE_54,
+	WL12XX_CONF_HW_RXTX_RATE_48,
+	WL12XX_CONF_HW_RXTX_RATE_36,
+	WL12XX_CONF_HW_RXTX_RATE_24,
+	WL12XX_CONF_HW_RXTX_RATE_22,
+	WL12XX_CONF_HW_RXTX_RATE_18,
+	WL12XX_CONF_HW_RXTX_RATE_12,
+	WL12XX_CONF_HW_RXTX_RATE_11,
+	WL12XX_CONF_HW_RXTX_RATE_9,
+	WL12XX_CONF_HW_RXTX_RATE_6,
+	WL12XX_CONF_HW_RXTX_RATE_5_5,
+	WL12XX_CONF_HW_RXTX_RATE_2,
+	WL12XX_CONF_HW_RXTX_RATE_1,
+	WL12XX_CONF_HW_RXTX_RATE_MAX,
+};
+
+static struct wlcore_partition_set wl12xx_ptable[PART_TABLE_LEN] = {
+	[PART_DOWN] = {
+		.mem = {
+			.start = 0x00000000,
+			.size  = 0x000177c0
+		},
+		.reg = {
+			.start = REGISTERS_BASE,
+			.size  = 0x00008800
+		},
+		.mem2 = {
+			.start = 0x00000000,
+			.size  = 0x00000000
+		},
+		.mem3 = {
+			.start = 0x00000000,
+			.size  = 0x00000000
+		},
+	},
+
+	[PART_BOOT] = { /* in wl12xx we can use a mix of work and down
+			 * partition here */
+		.mem = {
+			.start = 0x00040000,
+			.size  = 0x00014fc0
+		},
+		.reg = {
+			.start = REGISTERS_BASE,
+			.size  = 0x00008800
+		},
+		.mem2 = {
+			.start = 0x00000000,
+			.size  = 0x00000000
+		},
+		.mem3 = {
+			.start = 0x00000000,
+			.size  = 0x00000000
+		},
+	},
+
+	[PART_WORK] = {
+		.mem = {
+			.start = 0x00040000,
+			.size  = 0x00014fc0
+		},
+		.reg = {
+			.start = REGISTERS_BASE,
+			.size  = 0x0000a000
+		},
+		.mem2 = {
+			.start = 0x003004f8,
+			.size  = 0x00000004
+		},
+		.mem3 = {
+			.start = 0x00040404,
+			.size  = 0x00000000
+		},
+	},
+
+	[PART_DRPW] = {
+		.mem = {
+			.start = 0x00040000,
+			.size  = 0x00014fc0
+		},
+		.reg = {
+			.start = DRPW_BASE,
+			.size  = 0x00006000
+		},
+		.mem2 = {
+			.start = 0x00000000,
+			.size  = 0x00000000
+		},
+		.mem3 = {
+			.start = 0x00000000,
+			.size  = 0x00000000
+		}
+	}
+};
+
+static const int wl12xx_rtable[REG_TABLE_LEN] = {
+	[REG_ECPU_CONTROL]		= WL12XX_REG_ECPU_CONTROL,
+	[REG_INTERRUPT_NO_CLEAR]	= WL12XX_REG_INTERRUPT_NO_CLEAR,
+	[REG_INTERRUPT_ACK]		= WL12XX_REG_INTERRUPT_ACK,
+	[REG_COMMAND_MAILBOX_PTR]	= WL12XX_REG_COMMAND_MAILBOX_PTR,
+	[REG_EVENT_MAILBOX_PTR]		= WL12XX_REG_EVENT_MAILBOX_PTR,
+	[REG_INTERRUPT_TRIG]		= WL12XX_REG_INTERRUPT_TRIG,
+	[REG_INTERRUPT_MASK]		= WL12XX_REG_INTERRUPT_MASK,
+	[REG_PC_ON_RECOVERY]		= WL12XX_SCR_PAD4,
+	[REG_CHIP_ID_B]			= WL12XX_CHIP_ID_B,
+	[REG_CMD_MBOX_ADDRESS]		= WL12XX_CMD_MBOX_ADDRESS,
+
+	/* data access memory addresses, used with partition translation */
+	[REG_SLV_MEM_DATA]		= WL1271_SLV_MEM_DATA,
+	[REG_SLV_REG_DATA]		= WL1271_SLV_REG_DATA,
+
+	/* raw data access memory addresses */
+	[REG_RAW_FW_STATUS_ADDR]	= FW_STATUS_ADDR,
+};
+
+/* TODO: maybe move to a new header file? */
+#define WL127X_FW_NAME_MULTI	"ti-connectivity/wl127x-fw-4-mr.bin"
+#define WL127X_FW_NAME_SINGLE	"ti-connectivity/wl127x-fw-4-sr.bin"
+#define WL127X_PLT_FW_NAME	"ti-connectivity/wl127x-fw-4-plt.bin"
+
+#define WL128X_FW_NAME_MULTI	"ti-connectivity/wl128x-fw-4-mr.bin"
+#define WL128X_FW_NAME_SINGLE	"ti-connectivity/wl128x-fw-4-sr.bin"
+#define WL128X_PLT_FW_NAME	"ti-connectivity/wl128x-fw-4-plt.bin"
+
+static void wl127x_prepare_read(struct wl1271 *wl, u32 rx_desc, u32 len)
+{
+	if (wl->chip.id != CHIP_ID_1283_PG20) {
+		struct wl1271_acx_mem_map *wl_mem_map = wl->target_mem_map;
+		struct wl1271_rx_mem_pool_addr rx_mem_addr;
+
+		/*
+		 * Choose the block we want to read
+		 * For aggregated packets, only the first memory block
+		 * should be retrieved. The FW takes care of the rest.
+		 */
+		u32 mem_block = rx_desc & RX_MEM_BLOCK_MASK;
+
+		rx_mem_addr.addr = (mem_block << 8) +
+			le32_to_cpu(wl_mem_map->packet_memory_pool_start);
+
+		rx_mem_addr.addr_extra = rx_mem_addr.addr + 4;
+
+		wl1271_write(wl, WL1271_SLV_REG_DATA,
+			     &rx_mem_addr, sizeof(rx_mem_addr), false);
+	}
+}
+
+static int wl12xx_identify_chip(struct wl1271 *wl)
+{
+	int ret = 0;
+
+	switch (wl->chip.id) {
+	case CHIP_ID_1271_PG10:
+		wl1271_warning("chip id 0x%x (1271 PG10) support is obsolete",
+			       wl->chip.id);
+
+		/* clear the alignment quirk, since we don't support it */
+		wl->quirks &= ~WLCORE_QUIRK_TX_BLOCKSIZE_ALIGN;
+
+		wl->quirks |= WLCORE_QUIRK_LEGACY_NVS;
+		wl->sr_fw_name = WL127X_FW_NAME_SINGLE;
+		wl->mr_fw_name = WL127X_FW_NAME_MULTI;
+		memcpy(&wl->conf.mem, &wl12xx_default_priv_conf.mem_wl127x,
+		       sizeof(wl->conf.mem));
+
+		/* read data preparation is only needed by wl127x */
+		wl->ops->prepare_read = wl127x_prepare_read;
+
+		break;
+
+	case CHIP_ID_1271_PG20:
+		wl1271_debug(DEBUG_BOOT, "chip id 0x%x (1271 PG20)",
+			     wl->chip.id);
+
+		/* clear the alignment quirk, since we don't support it */
+		wl->quirks &= ~WLCORE_QUIRK_TX_BLOCKSIZE_ALIGN;
+
+		wl->quirks |= WLCORE_QUIRK_LEGACY_NVS;
+		wl->plt_fw_name = WL127X_PLT_FW_NAME;
+		wl->sr_fw_name = WL127X_FW_NAME_SINGLE;
+		wl->mr_fw_name = WL127X_FW_NAME_MULTI;
+		memcpy(&wl->conf.mem, &wl12xx_default_priv_conf.mem_wl127x,
+		       sizeof(wl->conf.mem));
+
+		/* read data preparation is only needed by wl127x */
+		wl->ops->prepare_read = wl127x_prepare_read;
+
+		break;
+
+	case CHIP_ID_1283_PG20:
+		wl1271_debug(DEBUG_BOOT, "chip id 0x%x (1283 PG20)",
+			     wl->chip.id);
+		wl->plt_fw_name = WL128X_PLT_FW_NAME;
+		wl->sr_fw_name = WL128X_FW_NAME_SINGLE;
+		wl->mr_fw_name = WL128X_FW_NAME_MULTI;
+		break;
+	case CHIP_ID_1283_PG10:
+	default:
+		wl1271_warning("unsupported chip id: 0x%x", wl->chip.id);
+		ret = -ENODEV;
+		goto out;
+	}
+
+out:
+	return ret;
+}
+
+static void wl12xx_top_reg_write(struct wl1271 *wl, int addr, u16 val)
+{
+	/* write address >> 1 + 0x30000 to OCP_POR_CTR */
+	addr = (addr >> 1) + 0x30000;
+	wl1271_write32(wl, WL12XX_OCP_POR_CTR, addr);
+
+	/* write value to OCP_POR_WDATA */
+	wl1271_write32(wl, WL12XX_OCP_DATA_WRITE, val);
+
+	/* write 1 to OCP_CMD */
+	wl1271_write32(wl, WL12XX_OCP_CMD, OCP_CMD_WRITE);
+}
+
+static u16 wl12xx_top_reg_read(struct wl1271 *wl, int addr)
+{
+	u32 val;
+	int timeout = OCP_CMD_LOOP;
+
+	/* write address >> 1 + 0x30000 to OCP_POR_CTR */
+	addr = (addr >> 1) + 0x30000;
+	wl1271_write32(wl, WL12XX_OCP_POR_CTR, addr);
+
+	/* write 2 to OCP_CMD */
+	wl1271_write32(wl, WL12XX_OCP_CMD, OCP_CMD_READ);
+
+	/* poll for data ready */
+	do {
+		val = wl1271_read32(wl, WL12XX_OCP_DATA_READ);
+	} while (!(val & OCP_READY_MASK) && --timeout);
+
+	if (!timeout) {
+		wl1271_warning("Top register access timed out.");
+		return 0xffff;
+	}
+
+	/* check data status and return if OK */
+	if ((val & OCP_STATUS_MASK) == OCP_STATUS_OK)
+		return val & 0xffff;
+	else {
+		wl1271_warning("Top register access returned error.");
+		return 0xffff;
+	}
+}
+
+static int wl128x_switch_tcxo_to_fref(struct wl1271 *wl)
+{
+	u16 spare_reg;
+
+	/* Mask bits [2] & [8:4] in the sys_clk_cfg register */
+	spare_reg = wl12xx_top_reg_read(wl, WL_SPARE_REG);
+	if (spare_reg == 0xFFFF)
+		return -EFAULT;
+	spare_reg |= (BIT(3) | BIT(5) | BIT(6));
+	wl12xx_top_reg_write(wl, WL_SPARE_REG, spare_reg);
+
+	/* Enable FREF_CLK_REQ & mux MCS and coex PLLs to FREF */
+	wl12xx_top_reg_write(wl, SYS_CLK_CFG_REG,
+			     WL_CLK_REQ_TYPE_PG2 | MCS_PLL_CLK_SEL_FREF);
+
+	/* Delay execution for 15msec, to let the HW settle */
+	mdelay(15);
+
+	return 0;
+}
+
+static bool wl128x_is_tcxo_valid(struct wl1271 *wl)
+{
+	u16 tcxo_detection;
+
+	tcxo_detection = wl12xx_top_reg_read(wl, TCXO_CLK_DETECT_REG);
+	if (tcxo_detection & TCXO_DET_FAILED)
+		return false;
+
+	return true;
+}
+
+static bool wl128x_is_fref_valid(struct wl1271 *wl)
+{
+	u16 fref_detection;
+
+	fref_detection = wl12xx_top_reg_read(wl, FREF_CLK_DETECT_REG);
+	if (fref_detection & FREF_CLK_DETECT_FAIL)
+		return false;
+
+	return true;
+}
+
+static int wl128x_manually_configure_mcs_pll(struct wl1271 *wl)
+{
+	wl12xx_top_reg_write(wl, MCS_PLL_M_REG, MCS_PLL_M_REG_VAL);
+	wl12xx_top_reg_write(wl, MCS_PLL_N_REG, MCS_PLL_N_REG_VAL);
+	wl12xx_top_reg_write(wl, MCS_PLL_CONFIG_REG, MCS_PLL_CONFIG_REG_VAL);
+
+	return 0;
+}
+
+static int wl128x_configure_mcs_pll(struct wl1271 *wl, int clk)
+{
+	u16 spare_reg;
+	u16 pll_config;
+	u8 input_freq;
+
+	/* Mask bits [3:1] in the sys_clk_cfg register */
+	spare_reg = wl12xx_top_reg_read(wl, WL_SPARE_REG);
+	if (spare_reg == 0xFFFF)
+		return -EFAULT;
+	spare_reg |= BIT(2);
+	wl12xx_top_reg_write(wl, WL_SPARE_REG, spare_reg);
+
+	/* Handle special cases of the TCXO clock */
+	if (wl->tcxo_clock == WL12XX_TCXOCLOCK_16_8 ||
+	    wl->tcxo_clock == WL12XX_TCXOCLOCK_33_6)
+		return wl128x_manually_configure_mcs_pll(wl);
+
+	/* Set the input frequency according to the selected clock source */
+	input_freq = (clk & 1) + 1;
+
+	pll_config = wl12xx_top_reg_read(wl, MCS_PLL_CONFIG_REG);
+	if (pll_config == 0xFFFF)
+		return -EFAULT;
+	pll_config |= (input_freq << MCS_SEL_IN_FREQ_SHIFT);
+	pll_config |= MCS_PLL_ENABLE_HP;
+	wl12xx_top_reg_write(wl, MCS_PLL_CONFIG_REG, pll_config);
+
+	return 0;
+}
+
+/*
+ * WL128x has two clocks input - TCXO and FREF.
+ * TCXO is the main clock of the device, while FREF is used to sync
+ * between the GPS and the cellular modem.
+ * In cases where TCXO is 32.736MHz or 16.368MHz, the FREF will be used
+ * as the WLAN/BT main clock.
+ */
+static int wl128x_boot_clk(struct wl1271 *wl, int *selected_clock)
+{
+	u16 sys_clk_cfg;
+
+	/* For XTAL-only modes, FREF will be used after switching from TCXO */
+	if (wl->ref_clock == WL12XX_REFCLOCK_26_XTAL ||
+	    wl->ref_clock == WL12XX_REFCLOCK_38_XTAL) {
+		if (!wl128x_switch_tcxo_to_fref(wl))
+			return -EINVAL;
+		goto fref_clk;
+	}
+
+	/* Query the HW, to determine which clock source we should use */
+	sys_clk_cfg = wl12xx_top_reg_read(wl, SYS_CLK_CFG_REG);
+	if (sys_clk_cfg == 0xFFFF)
+		return -EINVAL;
+	if (sys_clk_cfg & PRCM_CM_EN_MUX_WLAN_FREF)
+		goto fref_clk;
+
+	/* If TCXO is either 32.736MHz or 16.368MHz, switch to FREF */
+	if (wl->tcxo_clock == WL12XX_TCXOCLOCK_16_368 ||
+	    wl->tcxo_clock == WL12XX_TCXOCLOCK_32_736) {
+		if (!wl128x_switch_tcxo_to_fref(wl))
+			return -EINVAL;
+		goto fref_clk;
+	}
+
+	/* TCXO clock is selected */
+	if (!wl128x_is_tcxo_valid(wl))
+		return -EINVAL;
+	*selected_clock = wl->tcxo_clock;
+	goto config_mcs_pll;
+
+fref_clk:
+	/* FREF clock is selected */
+	if (!wl128x_is_fref_valid(wl))
+		return -EINVAL;
+	*selected_clock = wl->ref_clock;
+
+config_mcs_pll:
+	return wl128x_configure_mcs_pll(wl, *selected_clock);
+}
+
+static int wl127x_boot_clk(struct wl1271 *wl)
+{
+	u32 pause;
+	u32 clk;
+
+	if (WL127X_PG_GET_MAJOR(wl->hw_pg_ver) < 3)
+		wl->quirks |= WLCORE_QUIRK_END_OF_TRANSACTION;
+
+	if (wl->ref_clock == CONF_REF_CLK_19_2_E ||
+	    wl->ref_clock == CONF_REF_CLK_38_4_E ||
+	    wl->ref_clock == CONF_REF_CLK_38_4_M_XTAL)
+		/* ref clk: 19.2/38.4/38.4-XTAL */
+		clk = 0x3;
+	else if (wl->ref_clock == CONF_REF_CLK_26_E ||
+		 wl->ref_clock == CONF_REF_CLK_52_E)
+		/* ref clk: 26/52 */
+		clk = 0x5;
+	else
+		return -EINVAL;
+
+	if (wl->ref_clock != CONF_REF_CLK_19_2_E) {
+		u16 val;
+		/* Set clock type (open drain) */
+		val = wl12xx_top_reg_read(wl, OCP_REG_CLK_TYPE);
+		val &= FREF_CLK_TYPE_BITS;
+		wl12xx_top_reg_write(wl, OCP_REG_CLK_TYPE, val);
+
+		/* Set clock pull mode (no pull) */
+		val = wl12xx_top_reg_read(wl, OCP_REG_CLK_PULL);
+		val |= NO_PULL;
+		wl12xx_top_reg_write(wl, OCP_REG_CLK_PULL, val);
+	} else {
+		u16 val;
+		/* Set clock polarity */
+		val = wl12xx_top_reg_read(wl, OCP_REG_CLK_POLARITY);
+		val &= FREF_CLK_POLARITY_BITS;
+		val |= CLK_REQ_OUTN_SEL;
+		wl12xx_top_reg_write(wl, OCP_REG_CLK_POLARITY, val);
+	}
+
+	wl1271_write32(wl, WL12XX_PLL_PARAMETERS, clk);
+
+	pause = wl1271_read32(wl, WL12XX_PLL_PARAMETERS);
+
+	wl1271_debug(DEBUG_BOOT, "pause1 0x%x", pause);
+
+	pause &= ~(WU_COUNTER_PAUSE_VAL);
+	pause |= WU_COUNTER_PAUSE_VAL;
+	wl1271_write32(wl, WL12XX_WU_COUNTER_PAUSE, pause);
+
+	return 0;
+}
+
+static int wl1271_boot_soft_reset(struct wl1271 *wl)
+{
+	unsigned long timeout;
+	u32 boot_data;
+
+	/* perform soft reset */
+	wl1271_write32(wl, WL12XX_SLV_SOFT_RESET, ACX_SLV_SOFT_RESET_BIT);
+
+	/* SOFT_RESET is self clearing */
+	timeout = jiffies + usecs_to_jiffies(SOFT_RESET_MAX_TIME);
+	while (1) {
+		boot_data = wl1271_read32(wl, WL12XX_SLV_SOFT_RESET);
+		wl1271_debug(DEBUG_BOOT, "soft reset bootdata 0x%x", boot_data);
+		if ((boot_data & ACX_SLV_SOFT_RESET_BIT) == 0)
+			break;
+
+		if (time_after(jiffies, timeout)) {
+			/* 1.2 check pWhalBus->uSelfClearTime if the
+			 * timeout was reached */
+			wl1271_error("soft reset timeout");
+			return -1;
+		}
+
+		udelay(SOFT_RESET_STALL_TIME);
+	}
+
+	/* disable Rx/Tx */
+	wl1271_write32(wl, WL12XX_ENABLE, 0x0);
+
+	/* disable auto calibration on start*/
+	wl1271_write32(wl, WL12XX_SPARE_A2, 0xffff);
+
+	return 0;
+}
+
+static int wl12xx_pre_boot(struct wl1271 *wl)
+{
+	int ret = 0;
+	u32 clk;
+	int selected_clock = -1;
+
+	if (wl->chip.id == CHIP_ID_1283_PG20) {
+		ret = wl128x_boot_clk(wl, &selected_clock);
+		if (ret < 0)
+			goto out;
+	} else {
+		ret = wl127x_boot_clk(wl);
+		if (ret < 0)
+			goto out;
+	}
+
+	/* Continue the ELP wake up sequence */
+	wl1271_write32(wl, WL12XX_WELP_ARM_COMMAND, WELP_ARM_COMMAND_VAL);
+	udelay(500);
+
+	wlcore_set_partition(wl, &wl->ptable[PART_DRPW]);
+
+	/* Read-modify-write DRPW_SCRATCH_START register (see next state)
+	   to be used by DRPw FW. The RTRIM value will be added by the FW
+	   before taking DRPw out of reset */
+
+	clk = wl1271_read32(wl, WL12XX_DRPW_SCRATCH_START);
+
+	wl1271_debug(DEBUG_BOOT, "clk2 0x%x", clk);
+
+	if (wl->chip.id == CHIP_ID_1283_PG20)
+		clk |= ((selected_clock & 0x3) << 1) << 4;
+	else
+		clk |= (wl->ref_clock << 1) << 4;
+
+	wl1271_write32(wl, WL12XX_DRPW_SCRATCH_START, clk);
+
+	wlcore_set_partition(wl, &wl->ptable[PART_WORK]);
+
+	/* Disable interrupts */
+	wlcore_write_reg(wl, REG_INTERRUPT_MASK, WL1271_ACX_INTR_ALL);
+
+	ret = wl1271_boot_soft_reset(wl);
+	if (ret < 0)
+		goto out;
+
+out:
+	return ret;
+}
+
+static void wl12xx_pre_upload(struct wl1271 *wl)
+{
+	u32 tmp;
+
+	/* write firmware's last address (ie. it's length) to
+	 * ACX_EEPROMLESS_IND_REG */
+	wl1271_debug(DEBUG_BOOT, "ACX_EEPROMLESS_IND_REG");
+
+	wl1271_write32(wl, WL12XX_EEPROMLESS_IND, WL12XX_EEPROMLESS_IND);
+
+	tmp = wlcore_read_reg(wl, REG_CHIP_ID_B);
+
+	wl1271_debug(DEBUG_BOOT, "chip id 0x%x", tmp);
+
+	/* 6. read the EEPROM parameters */
+	tmp = wl1271_read32(wl, WL12XX_SCR_PAD2);
+
+	/* WL1271: The reference driver skips steps 7 to 10 (jumps directly
+	 * to upload_fw) */
+
+	if (wl->chip.id == CHIP_ID_1283_PG20)
+		wl12xx_top_reg_write(wl, SDIO_IO_DS, HCI_IO_DS_6MA);
+}
+
+static void wl12xx_enable_interrupts(struct wl1271 *wl)
+{
+	u32 polarity;
+
+	polarity = wl12xx_top_reg_read(wl, OCP_REG_POLARITY);
+
+	/* We use HIGH polarity, so unset the LOW bit */
+	polarity &= ~POLARITY_LOW;
+	wl12xx_top_reg_write(wl, OCP_REG_POLARITY, polarity);
+
+	wlcore_write_reg(wl, REG_INTERRUPT_MASK, WL1271_ACX_ALL_EVENTS_VECTOR);
+
+	wlcore_enable_interrupts(wl);
+	wlcore_write_reg(wl, REG_INTERRUPT_MASK,
+			 WL1271_ACX_INTR_ALL & ~(WL1271_INTR_MASK));
+
+	wl1271_write32(wl, WL12XX_HI_CFG, HI_CFG_DEF_VAL);
+}
+
+static int wl12xx_boot(struct wl1271 *wl)
+{
+	int ret;
+
+	ret = wl12xx_pre_boot(wl);
+	if (ret < 0)
+		goto out;
+
+	ret = wlcore_boot_upload_nvs(wl);
+	if (ret < 0)
+		goto out;
+
+	wl12xx_pre_upload(wl);
+
+	ret = wlcore_boot_upload_firmware(wl);
+	if (ret < 0)
+		goto out;
+
+	ret = wlcore_boot_run_firmware(wl);
+	if (ret < 0)
+		goto out;
+
+	wl12xx_enable_interrupts(wl);
+
+out:
+	return ret;
+}
+
+static void wl12xx_trigger_cmd(struct wl1271 *wl, int cmd_box_addr,
+			       void *buf, size_t len)
+{
+	wl1271_write(wl, cmd_box_addr, buf, len, false);
+	wlcore_write_reg(wl, REG_INTERRUPT_TRIG, WL12XX_INTR_TRIG_CMD);
+}
+
+static void wl12xx_ack_event(struct wl1271 *wl)
+{
+	wlcore_write_reg(wl, REG_INTERRUPT_TRIG, WL12XX_INTR_TRIG_EVENT_ACK);
+}
+
+static u32 wl12xx_calc_tx_blocks(struct wl1271 *wl, u32 len, u32 spare_blks)
+{
+	u32 blk_size = WL12XX_TX_HW_BLOCK_SIZE;
+	u32 align_len = wlcore_calc_packet_alignment(wl, len);
+
+	return (align_len + blk_size - 1) / blk_size + spare_blks;
+}
+
+static void
+wl12xx_set_tx_desc_blocks(struct wl1271 *wl, struct wl1271_tx_hw_descr *desc,
+			  u32 blks, u32 spare_blks)
+{
+	if (wl->chip.id == CHIP_ID_1283_PG20) {
+		desc->wl128x_mem.total_mem_blocks = blks;
+	} else {
+		desc->wl127x_mem.extra_blocks = spare_blks;
+		desc->wl127x_mem.total_mem_blocks = blks;
+	}
+}
+
+static void
+wl12xx_set_tx_desc_data_len(struct wl1271 *wl, struct wl1271_tx_hw_descr *desc,
+			    struct sk_buff *skb)
+{
+	u32 aligned_len = wlcore_calc_packet_alignment(wl, skb->len);
+
+	if (wl->chip.id == CHIP_ID_1283_PG20) {
+		desc->wl128x_mem.extra_bytes = aligned_len - skb->len;
+		desc->length = cpu_to_le16(aligned_len >> 2);
+
+		wl1271_debug(DEBUG_TX,
+			     "tx_fill_hdr: hlid: %d len: %d life: %d mem: %d extra: %d",
+			     desc->hlid,
+			     le16_to_cpu(desc->length),
+			     le16_to_cpu(desc->life_time),
+			     desc->wl128x_mem.total_mem_blocks,
+			     desc->wl128x_mem.extra_bytes);
+	} else {
+		/* calculate number of padding bytes */
+		int pad = aligned_len - skb->len;
+		desc->tx_attr |=
+			cpu_to_le16(pad << TX_HW_ATTR_OFST_LAST_WORD_PAD);
+
+		/* Store the aligned length in terms of words */
+		desc->length = cpu_to_le16(aligned_len >> 2);
+
+		wl1271_debug(DEBUG_TX,
+			     "tx_fill_hdr: pad: %d hlid: %d len: %d life: %d mem: %d",
+			     pad, desc->hlid,
+			     le16_to_cpu(desc->length),
+			     le16_to_cpu(desc->life_time),
+			     desc->wl127x_mem.total_mem_blocks);
+	}
+}
+
+static enum wl_rx_buf_align
+wl12xx_get_rx_buf_align(struct wl1271 *wl, u32 rx_desc)
+{
+	if (rx_desc & RX_BUF_UNALIGNED_PAYLOAD)
+		return WLCORE_RX_BUF_UNALIGNED;
+
+	return WLCORE_RX_BUF_ALIGNED;
+}
+
+static u32 wl12xx_get_rx_packet_len(struct wl1271 *wl, void *rx_data,
+				    u32 data_len)
+{
+	struct wl1271_rx_descriptor *desc = rx_data;
+
+	/* invalid packet */
+	if (data_len < sizeof(*desc) ||
+	    data_len < sizeof(*desc) + desc->pad_len)
+		return 0;
+
+	return data_len - sizeof(*desc) - desc->pad_len;
+}
+
+static void wl12xx_tx_delayed_compl(struct wl1271 *wl)
+{
+	if (wl->fw_status->tx_results_counter == (wl->tx_results_count & 0xff))
+		return;
+
+	wl1271_tx_complete(wl);
+}
+
+static int wl12xx_hw_init(struct wl1271 *wl)
+{
+	int ret;
+
+	if (wl->chip.id == CHIP_ID_1283_PG20) {
+		u32 host_cfg_bitmap = HOST_IF_CFG_RX_FIFO_ENABLE;
+
+		ret = wl128x_cmd_general_parms(wl);
+		if (ret < 0)
+			goto out;
+		ret = wl128x_cmd_radio_parms(wl);
+		if (ret < 0)
+			goto out;
+
+		if (wl->quirks & WLCORE_QUIRK_TX_BLOCKSIZE_ALIGN)
+			/* Enable SDIO padding */
+			host_cfg_bitmap |= HOST_IF_CFG_TX_PAD_TO_SDIO_BLK;
+
+		/* Must be before wl1271_acx_init_mem_config() */
+		ret = wl1271_acx_host_if_cfg_bitmap(wl, host_cfg_bitmap);
+		if (ret < 0)
+			goto out;
+	} else {
+		ret = wl1271_cmd_general_parms(wl);
+		if (ret < 0)
+			goto out;
+		ret = wl1271_cmd_radio_parms(wl);
+		if (ret < 0)
+			goto out;
+		ret = wl1271_cmd_ext_radio_parms(wl);
+		if (ret < 0)
+			goto out;
+	}
+out:
+	return ret;
+}
+
+static u32 wl12xx_sta_get_ap_rate_mask(struct wl1271 *wl,
+				       struct wl12xx_vif *wlvif)
+{
+	return wlvif->rate_set;
+}
+
+static int wl12xx_identify_fw(struct wl1271 *wl)
+{
+	unsigned int *fw_ver = wl->chip.fw_ver;
+
+	/* Only new station firmwares support routing fw logs to the host */
+	if ((fw_ver[FW_VER_IF_TYPE] == FW_VER_IF_TYPE_STA) &&
+	    (fw_ver[FW_VER_MINOR] < FW_VER_MINOR_FWLOG_STA_MIN))
+		wl->quirks |= WLCORE_QUIRK_FWLOG_NOT_IMPLEMENTED;
+
+	/* This feature is not yet supported for AP mode */
+	if (fw_ver[FW_VER_IF_TYPE] == FW_VER_IF_TYPE_AP)
+		wl->quirks |= WLCORE_QUIRK_FWLOG_NOT_IMPLEMENTED;
+
+	return 0;
+}
+
+static void wl12xx_conf_init(struct wl1271 *wl)
+{
+	struct wl12xx_priv *priv = wl->priv;
+
+	/* apply driver default configuration */
+	memcpy(&wl->conf, &wl12xx_conf, sizeof(wl12xx_conf));
+
+	/* apply default private configuration */
+	memcpy(&priv->conf, &wl12xx_default_priv_conf, sizeof(priv->conf));
+}
+
+static bool wl12xx_mac_in_fuse(struct wl1271 *wl)
+{
+	bool supported = false;
+	u8 major, minor;
+
+	if (wl->chip.id == CHIP_ID_1283_PG20) {
+		major = WL128X_PG_GET_MAJOR(wl->hw_pg_ver);
+		minor = WL128X_PG_GET_MINOR(wl->hw_pg_ver);
+
+		/* in wl128x we have the MAC address if the PG is >= (2, 1) */
+		if (major > 2 || (major == 2 && minor >= 1))
+			supported = true;
+	} else {
+		major = WL127X_PG_GET_MAJOR(wl->hw_pg_ver);
+		minor = WL127X_PG_GET_MINOR(wl->hw_pg_ver);
+
+		/* in wl127x we have the MAC address if the PG is >= (3, 1) */
+		if (major == 3 && minor >= 1)
+			supported = true;
+	}
+
+	wl1271_debug(DEBUG_PROBE,
+		     "PG Ver major = %d minor = %d, MAC %s present",
+		     major, minor, supported ? "is" : "is not");
+
+	return supported;
+}
+
+static void wl12xx_get_fuse_mac(struct wl1271 *wl)
+{
+	u32 mac1, mac2;
+
+	wlcore_set_partition(wl, &wl->ptable[PART_DRPW]);
+
+	mac1 = wl1271_read32(wl, WL12XX_REG_FUSE_BD_ADDR_1);
+	mac2 = wl1271_read32(wl, WL12XX_REG_FUSE_BD_ADDR_2);
+
+	/* these are the two parts of the BD_ADDR */
+	wl->fuse_oui_addr = ((mac2 & 0xffff) << 8) +
+		((mac1 & 0xff000000) >> 24);
+	wl->fuse_nic_addr = mac1 & 0xffffff;
+
+	wlcore_set_partition(wl, &wl->ptable[PART_DOWN]);
+}
+
+static s8 wl12xx_get_pg_ver(struct wl1271 *wl)
+{
+	u32 die_info;
+
+	if (wl->chip.id == CHIP_ID_1283_PG20)
+		die_info = wl12xx_top_reg_read(wl, WL128X_REG_FUSE_DATA_2_1);
+	else
+		die_info = wl12xx_top_reg_read(wl, WL127X_REG_FUSE_DATA_2_1);
+
+	return (s8) (die_info & PG_VER_MASK) >> PG_VER_OFFSET;
+}
+
+static void wl12xx_get_mac(struct wl1271 *wl)
+{
+	if (wl12xx_mac_in_fuse(wl))
+		wl12xx_get_fuse_mac(wl);
+}
+
+static struct wlcore_ops wl12xx_ops = {
+	.identify_chip		= wl12xx_identify_chip,
+	.identify_fw		= wl12xx_identify_fw,
+	.boot			= wl12xx_boot,
+	.trigger_cmd		= wl12xx_trigger_cmd,
+	.ack_event		= wl12xx_ack_event,
+	.calc_tx_blocks		= wl12xx_calc_tx_blocks,
+	.set_tx_desc_blocks	= wl12xx_set_tx_desc_blocks,
+	.set_tx_desc_data_len	= wl12xx_set_tx_desc_data_len,
+	.get_rx_buf_align	= wl12xx_get_rx_buf_align,
+	.get_rx_packet_len	= wl12xx_get_rx_packet_len,
+	.tx_immediate_compl	= NULL,
+	.tx_delayed_compl	= wl12xx_tx_delayed_compl,
+	.hw_init		= wl12xx_hw_init,
+	.init_vif		= NULL,
+	.sta_get_ap_rate_mask	= wl12xx_sta_get_ap_rate_mask,
+	.get_pg_ver		= wl12xx_get_pg_ver,
+	.get_mac		= wl12xx_get_mac,
+};
+
+static struct ieee80211_sta_ht_cap wl12xx_ht_cap = {
+	.cap = IEEE80211_HT_CAP_GRN_FLD | IEEE80211_HT_CAP_SGI_20 |
+	       (1 << IEEE80211_HT_CAP_RX_STBC_SHIFT),
+	.ht_supported = true,
+	.ampdu_factor = IEEE80211_HT_MAX_AMPDU_8K,
+	.ampdu_density = IEEE80211_HT_MPDU_DENSITY_8,
+	.mcs = {
+		.rx_mask = { 0xff, 0, 0, 0, 0, 0, 0, 0, 0, 0, },
+		.rx_highest = cpu_to_le16(72),
+		.tx_params = IEEE80211_HT_MCS_TX_DEFINED,
+		},
+};
+
+static int __devinit wl12xx_probe(struct platform_device *pdev)
+{
+	struct wl1271 *wl;
+	struct ieee80211_hw *hw;
+	struct wl12xx_priv *priv;
+
+	hw = wlcore_alloc_hw(sizeof(*priv));
+	if (IS_ERR(hw)) {
+		wl1271_error("can't allocate hw");
+		return PTR_ERR(hw);
+	}
+
+	wl = hw->priv;
+	wl->ops = &wl12xx_ops;
+	wl->ptable = wl12xx_ptable;
+	wl->rtable = wl12xx_rtable;
+	wl->num_tx_desc = 16;
+	wl->normal_tx_spare = WL12XX_TX_HW_BLOCK_SPARE_DEFAULT;
+	wl->gem_tx_spare = WL12XX_TX_HW_BLOCK_GEM_SPARE;
+	wl->band_rate_to_idx = wl12xx_band_rate_to_idx;
+	wl->hw_tx_rate_tbl_size = WL12XX_CONF_HW_RXTX_RATE_MAX;
+	wl->hw_min_ht_rate = WL12XX_CONF_HW_RXTX_RATE_MCS0;
+	wl->fw_status_priv_len = 0;
+	memcpy(&wl->ht_cap, &wl12xx_ht_cap, sizeof(wl12xx_ht_cap));
+	wl12xx_conf_init(wl);
+
+	return wlcore_probe(wl, pdev);
+}
+
+static const struct platform_device_id wl12xx_id_table[] __devinitconst = {
+	{ "wl12xx", 0 },
+	{  } /* Terminating Entry */
+};
+MODULE_DEVICE_TABLE(platform, wl12xx_id_table);
+
+static struct platform_driver wl12xx_driver = {
+	.probe		= wl12xx_probe,
+	.remove		= __devexit_p(wlcore_remove),
+	.id_table	= wl12xx_id_table,
+	.driver = {
+		.name	= "wl12xx_driver",
+		.owner	= THIS_MODULE,
+	}
+};
+
+static int __init wl12xx_init(void)
+{
+	return platform_driver_register(&wl12xx_driver);
+}
+module_init(wl12xx_init);
+
+static void __exit wl12xx_exit(void)
+{
+	platform_driver_unregister(&wl12xx_driver);
+}
+module_exit(wl12xx_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Luciano Coelho <coelho@ti.com>");
+MODULE_FIRMWARE(WL127X_FW_NAME_SINGLE);
+MODULE_FIRMWARE(WL127X_FW_NAME_MULTI);
+MODULE_FIRMWARE(WL127X_PLT_FW_NAME);
+MODULE_FIRMWARE(WL128X_FW_NAME_SINGLE);
+MODULE_FIRMWARE(WL128X_FW_NAME_MULTI);
+MODULE_FIRMWARE(WL128X_PLT_FW_NAME);
diff --git a/drivers/net/wireless/ti/wl12xx/reg.h b/drivers/net/wireless/ti/wl12xx/reg.h
new file mode 100644
index 000000000000..79ede02e2587
--- /dev/null
+++ b/drivers/net/wireless/ti/wl12xx/reg.h
@@ -0,0 +1,556 @@
+/*
+ * This file is part of wl12xx
+ *
+ * Copyright (C) 1998-2009 Texas Instruments. All rights reserved.
+ * Copyright (C) 2009 Nokia Corporation
+ *
+ * Contact: Luciano Coelho <luciano.coelho@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef __REG_H__
+#define __REG_H__
+
+#include <linux/bitops.h>
+
+#define REGISTERS_BASE 0x00300000
+#define DRPW_BASE      0x00310000
+
+#define REGISTERS_DOWN_SIZE 0x00008800
+#define REGISTERS_WORK_SIZE 0x0000b000
+
+#define FW_STATUS_ADDR                      (0x14FC0 + 0xA000)
+
+/*===============================================
+   Host Software Reset - 32bit RW
+ ------------------------------------------
+    [31:1] Reserved
+    0  SOFT_RESET Soft Reset  - When this bit is set,
+    it holds the Wlan hardware in a soft reset state.
+    This reset disables all MAC and baseband processor
+    clocks except the CardBus/PCI interface clock.
+    It also initializes all MAC state machines except
+    the host interface. It does not reload the
+    contents of the EEPROM. When this bit is cleared
+    (not self-clearing), the Wlan hardware
+    exits the software reset state.
+===============================================*/
+#define WL12XX_SLV_SOFT_RESET		(REGISTERS_BASE + 0x0000)
+
+#define WL1271_SLV_REG_DATA            (REGISTERS_BASE + 0x0008)
+#define WL1271_SLV_REG_ADATA           (REGISTERS_BASE + 0x000c)
+#define WL1271_SLV_MEM_DATA            (REGISTERS_BASE + 0x0018)
+
+#define WL12XX_REG_INTERRUPT_TRIG         (REGISTERS_BASE + 0x0474)
+#define WL12XX_REG_INTERRUPT_TRIG_H       (REGISTERS_BASE + 0x0478)
+
+/*=============================================
+  Host Interrupt Mask Register - 32bit (RW)
+  ------------------------------------------
+  Setting a bit in this register masks the
+  corresponding interrupt to the host.
+  0 - RX0		- Rx first dubble buffer Data Interrupt
+  1 - TXD		- Tx Data Interrupt
+  2 - TXXFR		- Tx Transfer Interrupt
+  3 - RX1		- Rx second dubble buffer Data Interrupt
+  4 - RXXFR		- Rx Transfer Interrupt
+  5 - EVENT_A	- Event Mailbox interrupt
+  6 - EVENT_B	- Event Mailbox interrupt
+  7 - WNONHST	- Wake On Host Interrupt
+  8 - TRACE_A	- Debug Trace interrupt
+  9 - TRACE_B	- Debug Trace interrupt
+ 10 - CDCMP		- Command Complete Interrupt
+ 11 -
+ 12 -
+ 13 -
+ 14 - ICOMP		- Initialization Complete Interrupt
+ 16 - SG SE		- Soft Gemini - Sense enable interrupt
+ 17 - SG SD		- Soft Gemini - Sense disable interrupt
+ 18 -			-
+ 19 -			-
+ 20 -			-
+ 21-			-
+ Default: 0x0001
+*==============================================*/
+#define WL12XX_REG_INTERRUPT_MASK         (REGISTERS_BASE + 0x04DC)
+
+/*=============================================
+  Host Interrupt Mask Set 16bit, (Write only)
+  ------------------------------------------
+ Setting a bit in this register sets
+ the corresponding bin in ACX_HINT_MASK register
+ without effecting the mask
+ state of other bits (0 = no effect).
+==============================================*/
+#define ACX_REG_HINT_MASK_SET          (REGISTERS_BASE + 0x04E0)
+
+/*=============================================
+  Host Interrupt Mask Clear 16bit,(Write only)
+  ------------------------------------------
+ Setting a bit in this register clears
+ the corresponding bin in ACX_HINT_MASK register
+ without effecting the mask
+ state of other bits (0 = no effect).
+=============================================*/
+#define ACX_REG_HINT_MASK_CLR          (REGISTERS_BASE + 0x04E4)
+
+/*=============================================
+  Host Interrupt Status Nondestructive Read
+  16bit,(Read only)
+  ------------------------------------------
+ The host can read this register to determine
+ which interrupts are active.
+ Reading this register doesn't
+ effect its content.
+=============================================*/
+#define WL12XX_REG_INTERRUPT_NO_CLEAR     (REGISTERS_BASE + 0x04E8)
+
+/*=============================================
+  Host Interrupt Status Clear on Read  Register
+  16bit,(Read only)
+  ------------------------------------------
+ The host can read this register to determine
+ which interrupts are active.
+ Reading this register clears it,
+ thus making all interrupts inactive.
+==============================================*/
+#define ACX_REG_INTERRUPT_CLEAR        (REGISTERS_BASE + 0x04F8)
+
+/*=============================================
+  Host Interrupt Acknowledge Register
+  16bit,(Write only)
+  ------------------------------------------
+ The host can set individual bits in this
+ register to clear (acknowledge) the corresp.
+ interrupt status bits in the HINT_STS_CLR and
+ HINT_STS_ND registers, thus making the
+ assotiated interrupt inactive. (0-no effect)
+==============================================*/
+#define WL12XX_REG_INTERRUPT_ACK          (REGISTERS_BASE + 0x04F0)
+
+#define WL12XX_REG_RX_DRIVER_COUNTER	(REGISTERS_BASE + 0x0538)
+
+/* Device Configuration registers*/
+#define SOR_CFG                        (REGISTERS_BASE + 0x0800)
+
+/* Embedded ARM CPU Control */
+
+/*===============================================
+ Halt eCPU   - 32bit RW
+ ------------------------------------------
+ 0 HALT_ECPU Halt Embedded CPU - This bit is the
+ compliment of bit 1 (MDATA2) in the SOR_CFG register.
+ During a hardware reset, this bit holds
+ the inverse of MDATA2.
+ When downloading firmware from the host,
+ set this bit (pull down MDATA2).
+ The host clears this bit after downloading the firmware into
+ zero-wait-state SSRAM.
+ When loading firmware from Flash, clear this bit (pull up MDATA2)
+ so that the eCPU can run the bootloader code in Flash
+ HALT_ECPU eCPU State
+ --------------------
+ 1 halt eCPU
+ 0 enable eCPU
+ ===============================================*/
+#define WL12XX_REG_ECPU_CONTROL           (REGISTERS_BASE + 0x0804)
+
+#define WL12XX_HI_CFG			(REGISTERS_BASE + 0x0808)
+
+/*===============================================
+ EEPROM Burst Read Start  - 32bit RW
+ ------------------------------------------
+ [31:1] Reserved
+ 0  ACX_EE_START -  EEPROM Burst Read Start 0
+ Setting this bit starts a burst read from
+ the external EEPROM.
+ If this bit is set (after reset) before an EEPROM read/write,
+ the burst read starts at EEPROM address 0.
+ Otherwise, it starts at the address
+ following the address of the previous access.
+ TheWlan hardware hardware clears this bit automatically.
+
+ Default: 0x00000000
+*================================================*/
+#define ACX_REG_EE_START               (REGISTERS_BASE + 0x080C)
+
+#define WL12XX_OCP_POR_CTR		(REGISTERS_BASE + 0x09B4)
+#define WL12XX_OCP_DATA_WRITE		(REGISTERS_BASE + 0x09B8)
+#define WL12XX_OCP_DATA_READ		(REGISTERS_BASE + 0x09BC)
+#define WL12XX_OCP_CMD			(REGISTERS_BASE + 0x09C0)
+
+#define WL12XX_HOST_WR_ACCESS		(REGISTERS_BASE + 0x09F8)
+
+#define WL12XX_CHIP_ID_B		(REGISTERS_BASE + 0x5674)
+
+#define WL12XX_ENABLE			(REGISTERS_BASE + 0x5450)
+
+/* Power Management registers */
+#define WL12XX_ELP_CFG_MODE		(REGISTERS_BASE + 0x5804)
+#define WL12XX_ELP_CMD			(REGISTERS_BASE + 0x5808)
+#define WL12XX_PLL_CAL_TIME		(REGISTERS_BASE + 0x5810)
+#define WL12XX_CLK_REQ_TIME		(REGISTERS_BASE + 0x5814)
+#define WL12XX_CLK_BUF_TIME		(REGISTERS_BASE + 0x5818)
+
+#define WL12XX_CFG_PLL_SYNC_CNT		(REGISTERS_BASE + 0x5820)
+
+/* Scratch Pad registers*/
+#define WL12XX_SCR_PAD0			(REGISTERS_BASE + 0x5608)
+#define WL12XX_SCR_PAD1			(REGISTERS_BASE + 0x560C)
+#define WL12XX_SCR_PAD2			(REGISTERS_BASE + 0x5610)
+#define WL12XX_SCR_PAD3			(REGISTERS_BASE + 0x5614)
+#define WL12XX_SCR_PAD4			(REGISTERS_BASE + 0x5618)
+#define WL12XX_SCR_PAD4_SET		(REGISTERS_BASE + 0x561C)
+#define WL12XX_SCR_PAD4_CLR		(REGISTERS_BASE + 0x5620)
+#define WL12XX_SCR_PAD5			(REGISTERS_BASE + 0x5624)
+#define WL12XX_SCR_PAD5_SET		(REGISTERS_BASE + 0x5628)
+#define WL12XX_SCR_PAD5_CLR		(REGISTERS_BASE + 0x562C)
+#define WL12XX_SCR_PAD6			(REGISTERS_BASE + 0x5630)
+#define WL12XX_SCR_PAD7			(REGISTERS_BASE + 0x5634)
+#define WL12XX_SCR_PAD8			(REGISTERS_BASE + 0x5638)
+#define WL12XX_SCR_PAD9			(REGISTERS_BASE + 0x563C)
+
+/* Spare registers*/
+#define WL12XX_SPARE_A1			(REGISTERS_BASE + 0x0994)
+#define WL12XX_SPARE_A2			(REGISTERS_BASE + 0x0998)
+#define WL12XX_SPARE_A3			(REGISTERS_BASE + 0x099C)
+#define WL12XX_SPARE_A4			(REGISTERS_BASE + 0x09A0)
+#define WL12XX_SPARE_A5			(REGISTERS_BASE + 0x09A4)
+#define WL12XX_SPARE_A6			(REGISTERS_BASE + 0x09A8)
+#define WL12XX_SPARE_A7			(REGISTERS_BASE + 0x09AC)
+#define WL12XX_SPARE_A8			(REGISTERS_BASE + 0x09B0)
+#define WL12XX_SPARE_B1			(REGISTERS_BASE + 0x5420)
+#define WL12XX_SPARE_B2			(REGISTERS_BASE + 0x5424)
+#define WL12XX_SPARE_B3			(REGISTERS_BASE + 0x5428)
+#define WL12XX_SPARE_B4			(REGISTERS_BASE + 0x542C)
+#define WL12XX_SPARE_B5			(REGISTERS_BASE + 0x5430)
+#define WL12XX_SPARE_B6			(REGISTERS_BASE + 0x5434)
+#define WL12XX_SPARE_B7			(REGISTERS_BASE + 0x5438)
+#define WL12XX_SPARE_B8			(REGISTERS_BASE + 0x543C)
+
+#define WL12XX_PLL_PARAMETERS		(REGISTERS_BASE + 0x6040)
+#define WL12XX_WU_COUNTER_PAUSE		(REGISTERS_BASE + 0x6008)
+#define WL12XX_WELP_ARM_COMMAND		(REGISTERS_BASE + 0x6100)
+#define WL12XX_DRPW_SCRATCH_START	(DRPW_BASE + 0x002C)
+
+#define WL12XX_CMD_MBOX_ADDRESS		0x407B4
+
+#define ACX_REG_EEPROM_START_BIT BIT(1)
+
+/* Command/Information Mailbox Pointers */
+
+/*===============================================
+  Command Mailbox Pointer - 32bit RW
+ ------------------------------------------
+ This register holds the start address of
+ the command mailbox located in the Wlan hardware memory.
+ The host must read this pointer after a reset to
+ find the location of the command mailbox.
+ The Wlan hardware initializes the command mailbox
+ pointer with the default address of the command mailbox.
+ The command mailbox pointer is not valid until after
+ the host receives the Init Complete interrupt from
+ the Wlan hardware.
+ ===============================================*/
+#define WL12XX_REG_COMMAND_MAILBOX_PTR		(WL12XX_SCR_PAD0)
+
+/*===============================================
+  Information Mailbox Pointer - 32bit RW
+ ------------------------------------------
+ This register holds the start address of
+ the information mailbox located in the Wlan hardware memory.
+ The host must read this pointer after a reset to find
+ the location of the information mailbox.
+ The Wlan hardware initializes the information mailbox pointer
+ with the default address of the information mailbox.
+ The information mailbox pointer is not valid
+ until after the host receives the Init Complete interrupt from
+ the Wlan hardware.
+ ===============================================*/
+#define WL12XX_REG_EVENT_MAILBOX_PTR		(WL12XX_SCR_PAD1)
+
+/*===============================================
+ EEPROM Read/Write Request 32bit RW
+ ------------------------------------------
+ 1 EE_READ - EEPROM Read Request 1 - Setting this bit
+ loads a single byte of data into the EE_DATA
+ register from the EEPROM location specified in
+ the EE_ADDR register.
+ The Wlan hardware hardware clears this bit automatically.
+ EE_DATA is valid when this bit is cleared.
+
+ 0 EE_WRITE  - EEPROM Write Request  - Setting this bit
+ writes a single byte of data from the EE_DATA register into the
+ EEPROM location specified in the EE_ADDR register.
+ The Wlan hardware hardware clears this bit automatically.
+*===============================================*/
+#define ACX_EE_CTL_REG                      EE_CTL
+#define EE_WRITE                            0x00000001ul
+#define EE_READ                             0x00000002ul
+
+/*===============================================
+  EEPROM Address  - 32bit RW
+  ------------------------------------------
+  This register specifies the address
+  within the EEPROM from/to which to read/write data.
+  ===============================================*/
+#define ACX_EE_ADDR_REG                     EE_ADDR
+
+/*===============================================
+  EEPROM Data  - 32bit RW
+  ------------------------------------------
+  This register either holds the read 8 bits of
+  data from the EEPROM or the write data
+  to be written to the EEPROM.
+  ===============================================*/
+#define ACX_EE_DATA_REG                     EE_DATA
+
+/*===============================================
+  EEPROM Base Address  - 32bit RW
+  ------------------------------------------
+  This register holds the upper nine bits
+  [23:15] of the 24-bit Wlan hardware memory
+  address for burst reads from EEPROM accesses.
+  The EEPROM provides the lower 15 bits of this address.
+  The MSB of the address from the EEPROM is ignored.
+  ===============================================*/
+#define ACX_EE_CFG                          EE_CFG
+
+/*===============================================
+  GPIO Output Values  -32bit, RW
+  ------------------------------------------
+  [31:16]  Reserved
+  [15: 0]  Specify the output values (at the output driver inputs) for
+  GPIO[15:0], respectively.
+  ===============================================*/
+#define ACX_GPIO_OUT_REG            GPIO_OUT
+#define ACX_MAX_GPIO_LINES          15
+
+/*===============================================
+  Contention window  -32bit, RW
+  ------------------------------------------
+  [31:26]  Reserved
+  [25:16]  Max (0x3ff)
+  [15:07]  Reserved
+  [06:00]  Current contention window value - default is 0x1F
+  ===============================================*/
+#define ACX_CONT_WIND_CFG_REG    CONT_WIND_CFG
+#define ACX_CONT_WIND_MIN_MASK   0x0000007f
+#define ACX_CONT_WIND_MAX        0x03ff0000
+
+#define REF_FREQ_19_2                       0
+#define REF_FREQ_26_0                       1
+#define REF_FREQ_38_4                       2
+#define REF_FREQ_40_0                       3
+#define REF_FREQ_33_6                       4
+#define REF_FREQ_NUM                        5
+
+#define LUT_PARAM_INTEGER_DIVIDER           0
+#define LUT_PARAM_FRACTIONAL_DIVIDER        1
+#define LUT_PARAM_ATTN_BB                   2
+#define LUT_PARAM_ALPHA_BB                  3
+#define LUT_PARAM_STOP_TIME_BB              4
+#define LUT_PARAM_BB_PLL_LOOP_FILTER        5
+#define LUT_PARAM_NUM                       6
+
+#define WL12XX_EEPROMLESS_IND		(WL12XX_SCR_PAD4)
+#define USE_EEPROM                          0
+#define NVS_DATA_BUNDARY_ALIGNMENT          4
+
+/* Firmware image header size */
+#define FW_HDR_SIZE 8
+
+/******************************************************************************
+
+    CHANNELS, BAND & REG DOMAINS definitions
+
+******************************************************************************/
+
+#define SHORT_PREAMBLE_BIT   BIT(0) /* CCK or Barker depending on the rate */
+#define OFDM_RATE_BIT        BIT(6)
+#define PBCC_RATE_BIT        BIT(7)
+
+enum {
+	CCK_LONG = 0,
+	CCK_SHORT = SHORT_PREAMBLE_BIT,
+	PBCC_LONG = PBCC_RATE_BIT,
+	PBCC_SHORT = PBCC_RATE_BIT | SHORT_PREAMBLE_BIT,
+	OFDM = OFDM_RATE_BIT
+};
+
+/******************************************************************************
+
+Transmit-Descriptor RATE-SET field definitions...
+
+Define a new "Rate-Set" for TX path that incorporates the
+Rate & Modulation info into a single 16-bit field.
+
+TxdRateSet_t:
+b15   - Indicates Preamble type (1=SHORT, 0=LONG).
+	Notes:
+	Must be LONG (0) for 1Mbps rate.
+	Does not apply (set to 0) for RevG-OFDM rates.
+b14   - Indicates PBCC encoding (1=PBCC, 0=not).
+	Notes:
+	Does not apply (set to 0) for rates 1 and 2 Mbps.
+	Does not apply (set to 0) for RevG-OFDM rates.
+b13    - Unused (set to 0).
+b12-b0 - Supported Rate indicator bits as defined below.
+
+******************************************************************************/
+
+#define OCP_CMD_LOOP		32
+#define OCP_CMD_WRITE		0x1
+#define OCP_CMD_READ		0x2
+#define OCP_READY_MASK		BIT(18)
+#define OCP_STATUS_MASK		(BIT(16) | BIT(17))
+#define OCP_STATUS_NO_RESP	0x00000
+#define OCP_STATUS_OK		0x10000
+#define OCP_STATUS_REQ_FAILED	0x20000
+#define OCP_STATUS_RESP_ERROR	0x30000
+
+#define OCP_REG_POLARITY     0x0064
+#define OCP_REG_CLK_TYPE     0x0448
+#define OCP_REG_CLK_POLARITY 0x0cb2
+#define OCP_REG_CLK_PULL     0x0cb4
+
+#define POLARITY_LOW         BIT(1)
+#define NO_PULL              (BIT(14) | BIT(15))
+
+#define FREF_CLK_TYPE_BITS     0xfffffe7f
+#define CLK_REQ_PRCM           0x100
+#define FREF_CLK_POLARITY_BITS 0xfffff8ff
+#define CLK_REQ_OUTN_SEL       0x700
+
+#define WU_COUNTER_PAUSE_VAL 0x3FF
+
+/* PLL configuration algorithm for wl128x */
+#define SYS_CLK_CFG_REG              0x2200
+/* Bit[0]   -  0-TCXO,  1-FREF */
+#define MCS_PLL_CLK_SEL_FREF         BIT(0)
+/* Bit[3:2] - 01-TCXO, 10-FREF */
+#define WL_CLK_REQ_TYPE_FREF         BIT(3)
+#define WL_CLK_REQ_TYPE_PG2          (BIT(3) | BIT(2))
+/* Bit[4]   -  0-TCXO,  1-FREF */
+#define PRCM_CM_EN_MUX_WLAN_FREF     BIT(4)
+
+#define TCXO_ILOAD_INT_REG           0x2264
+#define TCXO_CLK_DETECT_REG          0x2266
+
+#define TCXO_DET_FAILED              BIT(4)
+
+#define FREF_ILOAD_INT_REG           0x2084
+#define FREF_CLK_DETECT_REG          0x2086
+#define FREF_CLK_DETECT_FAIL         BIT(4)
+
+/* Use this reg for masking during driver access */
+#define WL_SPARE_REG                 0x2320
+#define WL_SPARE_VAL                 BIT(2)
+/* Bit[6:5:3] -  mask wl write SYS_CLK_CFG[8:5:2:4] */
+#define WL_SPARE_MASK_8526           (BIT(6) | BIT(5) | BIT(3))
+
+#define PLL_LOCK_COUNTERS_REG        0xD8C
+#define PLL_LOCK_COUNTERS_COEX       0x0F
+#define PLL_LOCK_COUNTERS_MCS        0xF0
+#define MCS_PLL_OVERRIDE_REG         0xD90
+#define MCS_PLL_CONFIG_REG           0xD92
+#define MCS_SEL_IN_FREQ_MASK         0x0070
+#define MCS_SEL_IN_FREQ_SHIFT        4
+#define MCS_PLL_CONFIG_REG_VAL       0x73
+#define MCS_PLL_ENABLE_HP            (BIT(0) | BIT(1))
+
+#define MCS_PLL_M_REG                0xD94
+#define MCS_PLL_N_REG                0xD96
+#define MCS_PLL_M_REG_VAL            0xC8
+#define MCS_PLL_N_REG_VAL            0x07
+
+#define SDIO_IO_DS                   0xd14
+
+/* SDIO/wSPI DS configuration values */
+enum {
+	HCI_IO_DS_8MA = 0,
+	HCI_IO_DS_4MA = 1, /* default */
+	HCI_IO_DS_6MA = 2,
+	HCI_IO_DS_2MA = 3,
+};
+
+/* end PLL configuration algorithm for wl128x */
+
+/*
+ * Host Command Interrupt. Setting this bit masks
+ * the interrupt that the host issues to inform
+ * the FW that it has sent a command
+ * to the Wlan hardware Command Mailbox.
+ */
+#define WL12XX_INTR_TRIG_CMD		BIT(0)
+
+/*
+ * Host Event Acknowlegde Interrupt. The host
+ * sets this bit to acknowledge that it received
+ * the unsolicited information from the event
+ * mailbox.
+ */
+#define WL12XX_INTR_TRIG_EVENT_ACK	BIT(1)
+
+/*===============================================
+  HI_CFG Interface Configuration Register Values
+  ------------------------------------------
+  ===============================================*/
+#define HI_CFG_UART_ENABLE          0x00000004
+#define HI_CFG_RST232_ENABLE        0x00000008
+#define HI_CFG_CLOCK_REQ_SELECT     0x00000010
+#define HI_CFG_HOST_INT_ENABLE      0x00000020
+#define HI_CFG_VLYNQ_OUTPUT_ENABLE  0x00000040
+#define HI_CFG_HOST_INT_ACTIVE_LOW  0x00000080
+#define HI_CFG_UART_TX_OUT_GPIO_15  0x00000100
+#define HI_CFG_UART_TX_OUT_GPIO_14  0x00000200
+#define HI_CFG_UART_TX_OUT_GPIO_7   0x00000400
+
+#define HI_CFG_DEF_VAL              \
+	(HI_CFG_UART_ENABLE |        \
+	HI_CFG_RST232_ENABLE |      \
+	HI_CFG_CLOCK_REQ_SELECT |   \
+	HI_CFG_HOST_INT_ENABLE)
+
+#define WL127X_REG_FUSE_DATA_2_1	0x050a
+#define WL128X_REG_FUSE_DATA_2_1	0x2152
+#define PG_VER_MASK			0x3c
+#define PG_VER_OFFSET			2
+
+#define WL127X_PG_MAJOR_VER_MASK	0x3
+#define WL127X_PG_MAJOR_VER_OFFSET	0x0
+#define WL127X_PG_MINOR_VER_MASK	0xc
+#define WL127X_PG_MINOR_VER_OFFSET	0x2
+
+#define WL128X_PG_MAJOR_VER_MASK	0xc
+#define WL128X_PG_MAJOR_VER_OFFSET	0x2
+#define WL128X_PG_MINOR_VER_MASK	0x3
+#define WL128X_PG_MINOR_VER_OFFSET	0x0
+
+#define WL127X_PG_GET_MAJOR(pg_ver) ((pg_ver & WL127X_PG_MAJOR_VER_MASK) >> \
+				     WL127X_PG_MAJOR_VER_OFFSET)
+#define WL127X_PG_GET_MINOR(pg_ver) ((pg_ver & WL127X_PG_MINOR_VER_MASK) >> \
+				     WL127X_PG_MINOR_VER_OFFSET)
+#define WL128X_PG_GET_MAJOR(pg_ver) ((pg_ver & WL128X_PG_MAJOR_VER_MASK) >> \
+				     WL128X_PG_MAJOR_VER_OFFSET)
+#define WL128X_PG_GET_MINOR(pg_ver) ((pg_ver & WL128X_PG_MINOR_VER_MASK) >> \
+				     WL128X_PG_MINOR_VER_OFFSET)
+
+#define WL12XX_REG_FUSE_BD_ADDR_1	0x00310eb4
+#define WL12XX_REG_FUSE_BD_ADDR_2	0x00310eb8
+
+#endif
diff --git a/drivers/net/wireless/ti/wl12xx/wl12xx.h b/drivers/net/wireless/ti/wl12xx/wl12xx.h
new file mode 100644
index 000000000000..74cd332e23ef
--- /dev/null
+++ b/drivers/net/wireless/ti/wl12xx/wl12xx.h
@@ -0,0 +1,31 @@
+/*
+ * This file is part of wl12xx
+ *
+ * Copyright (C) 2011 Texas Instruments Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef __WL12XX_PRIV_H__
+#define __WL12XX_PRIV_H__
+
+#include "conf.h"
+
+struct wl12xx_priv {
+	struct wl12xx_priv_conf conf;
+};
+
+#endif /* __WL12XX_PRIV_H__ */