iwl3945: add load ucode op

The patch adds 3945 iwl_lib_ops->load_ucode to the driver.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1 files changed, 1 insertions, 151 deletions

diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c
index 52c03cf29089..6669ab0d3f52 100644
--- a/drivers/net/wireless/iwlwifi/iwl3945-base.c
+++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c
@@ -4924,156 +4924,6 @@ static int iwl3945_verify_ucode(struct iwl_priv *priv)
 	return rc;
 }
 
-
-/* check contents of special bootstrap uCode SRAM */
-static int iwl3945_verify_bsm(struct iwl_priv *priv)
-{
-	__le32 *image = priv->ucode_boot.v_addr;
-	u32 len = priv->ucode_boot.len;
-	u32 reg;
-	u32 val;
-
-	IWL_DEBUG_INFO("Begin verify bsm\n");
-
-	/* verify BSM SRAM contents */
-	val = iwl_read_prph(priv, BSM_WR_DWCOUNT_REG);
-	for (reg = BSM_SRAM_LOWER_BOUND;
-	     reg < BSM_SRAM_LOWER_BOUND + len;
-	     reg += sizeof(u32), image++) {
-		val = iwl_read_prph(priv, reg);
-		if (val != le32_to_cpu(*image)) {
-			IWL_ERR(priv, "BSM uCode verification failed at "
-				  "addr 0x%08X+%u (of %u), is 0x%x, s/b 0x%x\n",
-				  BSM_SRAM_LOWER_BOUND,
-				  reg - BSM_SRAM_LOWER_BOUND, len,
-				  val, le32_to_cpu(*image));
-			return -EIO;
-		}
-	}
-
-	IWL_DEBUG_INFO("BSM bootstrap uCode image OK\n");
-
-	return 0;
-}
-
-/**
- * iwl3945_load_bsm - Load bootstrap instructions
- *
- * BSM operation:
- *
- * The Bootstrap State Machine (BSM) stores a short bootstrap uCode program
- * in special SRAM that does not power down during RFKILL.  When powering back
- * up after power-saving sleeps (or during initial uCode load), the BSM loads
- * the bootstrap program into the on-board processor, and starts it.
- *
- * The bootstrap program loads (via DMA) instructions and data for a new
- * program from host DRAM locations indicated by the host driver in the
- * BSM_DRAM_* registers.  Once the new program is loaded, it starts
- * automatically.
- *
- * When initializing the NIC, the host driver points the BSM to the
- * "initialize" uCode image.  This uCode sets up some internal data, then
- * notifies host via "initialize alive" that it is complete.
- *
- * The host then replaces the BSM_DRAM_* pointer values to point to the
- * normal runtime uCode instructions and a backup uCode data cache buffer
- * (filled initially with starting data values for the on-board processor),
- * then triggers the "initialize" uCode to load and launch the runtime uCode,
- * which begins normal operation.
- *
- * When doing a power-save shutdown, runtime uCode saves data SRAM into
- * the backup data cache in DRAM before SRAM is powered down.
- *
- * When powering back up, the BSM loads the bootstrap program.  This reloads
- * the runtime uCode instructions and the backup data cache into SRAM,
- * and re-launches the runtime uCode from where it left off.
- */
-static int iwl3945_load_bsm(struct iwl_priv *priv)
-{
-	__le32 *image = priv->ucode_boot.v_addr;
-	u32 len = priv->ucode_boot.len;
-	dma_addr_t pinst;
-	dma_addr_t pdata;
-	u32 inst_len;
-	u32 data_len;
-	int rc;
-	int i;
-	u32 done;
-	u32 reg_offset;
-
-	IWL_DEBUG_INFO("Begin load bsm\n");
-
-	/* make sure bootstrap program is no larger than BSM's SRAM size */
-	if (len > IWL39_MAX_BSM_SIZE)
-		return -EINVAL;
-
-	/* Tell bootstrap uCode where to find the "Initialize" uCode
-	 *   in host DRAM ... host DRAM physical address bits 31:0 for 3945.
-	 * NOTE:  iwl3945_initialize_alive_start() will replace these values,
-	 *        after the "initialize" uCode has run, to point to
-	 *        runtime/protocol instructions and backup data cache. */
-	pinst = priv->ucode_init.p_addr;
-	pdata = priv->ucode_init_data.p_addr;
-	inst_len = priv->ucode_init.len;
-	data_len = priv->ucode_init_data.len;
-
-	rc = iwl_grab_nic_access(priv);
-	if (rc)
-		return rc;
-
-	iwl_write_prph(priv, BSM_DRAM_INST_PTR_REG, pinst);
-	iwl_write_prph(priv, BSM_DRAM_DATA_PTR_REG, pdata);
-	iwl_write_prph(priv, BSM_DRAM_INST_BYTECOUNT_REG, inst_len);
-	iwl_write_prph(priv, BSM_DRAM_DATA_BYTECOUNT_REG, data_len);
-
-	/* Fill BSM memory with bootstrap instructions */
-	for (reg_offset = BSM_SRAM_LOWER_BOUND;
-	     reg_offset < BSM_SRAM_LOWER_BOUND + len;
-	     reg_offset += sizeof(u32), image++)
-		_iwl_write_prph(priv, reg_offset,
-					  le32_to_cpu(*image));
-
-	rc = iwl3945_verify_bsm(priv);
-	if (rc) {
-		iwl_release_nic_access(priv);
-		return rc;
-	}
-
-	/* Tell BSM to copy from BSM SRAM into instruction SRAM, when asked */
-	iwl_write_prph(priv, BSM_WR_MEM_SRC_REG, 0x0);
-	iwl_write_prph(priv, BSM_WR_MEM_DST_REG,
-				 IWL39_RTC_INST_LOWER_BOUND);
-	iwl_write_prph(priv, BSM_WR_DWCOUNT_REG, len / sizeof(u32));
-
-	/* Load bootstrap code into instruction SRAM now,
-	 *   to prepare to load "initialize" uCode */
-	iwl_write_prph(priv, BSM_WR_CTRL_REG,
-		BSM_WR_CTRL_REG_BIT_START);
-
-	/* Wait for load of bootstrap uCode to finish */
-	for (i = 0; i < 100; i++) {
-		done = iwl_read_prph(priv, BSM_WR_CTRL_REG);
-		if (!(done & BSM_WR_CTRL_REG_BIT_START))
-			break;
-		udelay(10);
-	}
-	if (i < 100)
-		IWL_DEBUG_INFO("BSM write complete, poll %d iterations\n", i);
-	else {
-		IWL_ERR(priv, "BSM write did not complete!\n");
-		return -EIO;
-	}
-
-	/* Enable future boot loads whenever power management unit triggers it
-	 *   (e.g. when powering back up after power-save shutdown) */
-	iwl_write_prph(priv, BSM_WR_CTRL_REG,
-		BSM_WR_CTRL_REG_BIT_START_EN);
-
-	iwl_release_nic_access(priv);
-
-	return 0;
-}
-
 static void iwl3945_nic_start(struct iwl_priv *priv)
 {
 	/* Remove all resets to allow NIC to operate */
@@ -5714,7 +5564,7 @@ static int __iwl3945_up(struct iwl_priv *priv)
 		/* load bootstrap state machine,
 		 * load bootstrap program into processor's memory,
 		 * prepare to load the "initialize" uCode */
-		rc = iwl3945_load_bsm(priv);
+		priv->cfg->ops->lib->load_ucode(priv);
 
 		if (rc) {
 			IWL_ERR(priv,