Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 769 insertions, 0 deletions

diff --git a/drivers/net/seeq8005.c b/drivers/net/seeq8005.c
new file mode 100644
index 000000000000..79dca398f3ac
--- /dev/null
+++ b/drivers/net/seeq8005.c
@@ -0,0 +1,769 @@
+/* seeq8005.c: A network driver for linux. */
+/*
+	Based on skeleton.c,
+	Written 1993-94 by Donald Becker.
+	See the skeleton.c file for further copyright information.
+
+	This software may be used and distributed according to the terms
+	of the GNU General Public License, incorporated herein by reference.
+
+	The author may be reached as hamish@zot.apana.org.au
+
+	This file is a network device driver for the SEEQ 8005 chipset and
+	the Linux operating system.
+
+*/
+
+static const char version[] =
+	"seeq8005.c:v1.00 8/07/95 Hamish Coleman (hamish@zot.apana.org.au)\n";
+
+/*
+  Sources:
+  	SEEQ 8005 databook
+  	
+  Version history:
+  	1.00	Public release. cosmetic changes (no warnings now)
+  	0.68	Turning per- packet,interrupt debug messages off - testing for release.
+  	0.67	timing problems/bad buffer reads seem to be fixed now
+  	0.63	*!@$ protocol=eth_type_trans -- now packets flow
+  	0.56	Send working
+  	0.48	Receive working
+*/
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/fcntl.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/in.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/bitops.h>
+
+#include <asm/system.h>
+#include <asm/io.h>
+#include <asm/dma.h>
+
+#include "seeq8005.h"
+
+/* First, a few definitions that the brave might change. */
+/* A zero-terminated list of I/O addresses to be probed. */
+static unsigned int seeq8005_portlist[] __initdata =
+   { 0x300, 0x320, 0x340, 0x360, 0};
+
+/* use 0 for production, 1 for verification, >2 for debug */
+#ifndef NET_DEBUG
+#define NET_DEBUG 1
+#endif
+static unsigned int net_debug = NET_DEBUG;
+
+/* Information that need to be kept for each board. */
+struct net_local {
+	struct net_device_stats stats;
+	unsigned short receive_ptr;		/* What address in packet memory do we expect a recv_pkt_header? */
+	long open_time;				/* Useless example local info. */
+};
+
+/* The station (ethernet) address prefix, used for IDing the board. */
+#define SA_ADDR0 0x00
+#define SA_ADDR1 0x80
+#define SA_ADDR2 0x4b
+
+/* Index to functions, as function prototypes. */
+
+static int seeq8005_probe1(struct net_device *dev, int ioaddr);
+static int seeq8005_open(struct net_device *dev);
+static void seeq8005_timeout(struct net_device *dev);
+static int seeq8005_send_packet(struct sk_buff *skb, struct net_device *dev);
+static irqreturn_t seeq8005_interrupt(int irq, void *dev_id, struct pt_regs *regs);
+static void seeq8005_rx(struct net_device *dev);
+static int seeq8005_close(struct net_device *dev);
+static struct net_device_stats *seeq8005_get_stats(struct net_device *dev);
+static void set_multicast_list(struct net_device *dev);
+
+/* Example routines you must write ;->. */
+#define tx_done(dev)	(inw(SEEQ_STATUS) & SEEQSTAT_TX_ON)
+static void hardware_send_packet(struct net_device *dev, char *buf, int length);
+extern void seeq8005_init(struct net_device *dev, int startp);
+static inline void wait_for_buffer(struct net_device *dev);
+
+
+/* Check for a network adaptor of this type, and return '0' iff one exists.
+   If dev->base_addr == 0, probe all likely locations.
+   If dev->base_addr == 1, always return failure.
+   */
+
+static int io = 0x320;
+static int irq = 10;
+
+struct net_device * __init seeq8005_probe(int unit)
+{
+	struct net_device *dev = alloc_etherdev(sizeof(struct net_local));
+	unsigned *port;
+	int err = 0;
+
+	if (!dev)
+		return ERR_PTR(-ENODEV);
+
+	if (unit >= 0) {
+		sprintf(dev->name, "eth%d", unit);
+		netdev_boot_setup_check(dev);
+		io = dev->base_addr;
+		irq = dev->irq;
+	}
+
+	if (io > 0x1ff) {	/* Check a single specified location. */
+		err = seeq8005_probe1(dev, io);
+	} else if (io != 0) {	/* Don't probe at all. */
+		err = -ENXIO;
+	} else {
+		for (port = seeq8005_portlist; *port; port++) {
+			if (seeq8005_probe1(dev, *port) == 0)
+				break;
+		}
+		if (!*port)
+			err = -ENODEV;
+	}
+	if (err)
+		goto out;
+	err = register_netdev(dev);
+	if (err)
+		goto out1;
+	return dev;
+out1:
+	release_region(dev->base_addr, SEEQ8005_IO_EXTENT);
+out:
+	free_netdev(dev);
+	return ERR_PTR(err);
+}
+
+/* This is the real probe routine.  Linux has a history of friendly device
+   probes on the ISA bus.  A good device probes avoids doing writes, and
+   verifies that the correct device exists and functions.  */
+
+static int __init seeq8005_probe1(struct net_device *dev, int ioaddr)
+{
+	static unsigned version_printed;
+	int i,j;
+	unsigned char SA_prom[32];
+	int old_cfg1;
+	int old_cfg2;
+	int old_stat;
+	int old_dmaar;
+	int old_rear;
+	int retval;
+
+	if (!request_region(ioaddr, SEEQ8005_IO_EXTENT, "seeq8005"))
+		return -ENODEV;
+
+	if (net_debug>1)
+		printk("seeq8005: probing at 0x%x\n",ioaddr);
+
+	old_stat = inw(SEEQ_STATUS);					/* read status register */
+	if (old_stat == 0xffff) {
+		retval = -ENODEV;
+		goto out;						/* assume that 0xffff == no device */
+	}
+	if ( (old_stat & 0x1800) != 0x1800 ) {				/* assume that unused bits are 1, as my manual says */
+		if (net_debug>1) {
+			printk("seeq8005: reserved stat bits != 0x1800\n");
+			printk("          == 0x%04x\n",old_stat);
+		}
+	 	retval = -ENODEV;
+		goto out;
+	}
+
+	old_rear = inw(SEEQ_REA);
+	if (old_rear == 0xffff) {
+		outw(0,SEEQ_REA);
+		if (inw(SEEQ_REA) == 0xffff) {				/* assume that 0xffff == no device */
+			retval = -ENODEV;
+			goto out;
+		}
+	} else if ((old_rear & 0xff00) != 0xff00) {			/* assume that unused bits are 1 */
+		if (net_debug>1) {
+			printk("seeq8005: unused rear bits != 0xff00\n");
+			printk("          == 0x%04x\n",old_rear);
+		}
+		retval = -ENODEV;
+		goto out;
+	}
+	
+	old_cfg2 = inw(SEEQ_CFG2);					/* read CFG2 register */
+	old_cfg1 = inw(SEEQ_CFG1);
+	old_dmaar = inw(SEEQ_DMAAR);
+	
+	if (net_debug>4) {
+		printk("seeq8005: stat = 0x%04x\n",old_stat);
+		printk("seeq8005: cfg1 = 0x%04x\n",old_cfg1);
+		printk("seeq8005: cfg2 = 0x%04x\n",old_cfg2);
+		printk("seeq8005: raer = 0x%04x\n",old_rear);
+		printk("seeq8005: dmaar= 0x%04x\n",old_dmaar);
+	}
+	
+	outw( SEEQCMD_FIFO_WRITE | SEEQCMD_SET_ALL_OFF, SEEQ_CMD);	/* setup for reading PROM */
+	outw( 0, SEEQ_DMAAR);						/* set starting PROM address */
+	outw( SEEQCFG1_BUFFER_PROM, SEEQ_CFG1);				/* set buffer to look at PROM */
+
+
+	j=0;
+	for(i=0; i <32; i++) {
+		j+= SA_prom[i] = inw(SEEQ_BUFFER) & 0xff;
+	}
+
+#if 0
+	/* untested because I only have the one card */
+	if ( (j&0xff) != 0 ) {						/* checksum appears to be 8bit = 0 */
+		if (net_debug>1) {					/* check this before deciding that we have a card */
+			printk("seeq8005: prom sum error\n");
+		}
+		outw( old_stat, SEEQ_STATUS);
+		outw( old_dmaar, SEEQ_DMAAR);
+		outw( old_cfg1, SEEQ_CFG1);
+		retval = -ENODEV;
+		goto out;
+	}
+#endif
+
+	outw( SEEQCFG2_RESET, SEEQ_CFG2);				/* reset the card */
+	udelay(5);
+	outw( SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
+	
+	if (net_debug) {
+		printk("seeq8005: prom sum = 0x%08x\n",j);
+		for(j=0; j<32; j+=16) {
+			printk("seeq8005: prom %02x: ",j);
+			for(i=0;i<16;i++) {
+				printk("%02x ",SA_prom[j|i]);
+			}
+			printk(" ");
+			for(i=0;i<16;i++) {
+				if ((SA_prom[j|i]>31)&&(SA_prom[j|i]<127)) {
+					printk("%c", SA_prom[j|i]);
+				} else {
+					printk(" ");
+				}
+			}
+			printk("\n");
+		}
+	}
+
+#if 0	
+	/* 
+	 * testing the packet buffer memory doesn't work yet
+	 * but all other buffer accesses do 
+	 *			- fixing is not a priority
+	 */
+	if (net_debug>1) {					/* test packet buffer memory */
+		printk("seeq8005: testing packet buffer ... ");
+		outw( SEEQCFG1_BUFFER_BUFFER, SEEQ_CFG1);
+		outw( SEEQCMD_FIFO_WRITE | SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
+		outw( 0 , SEEQ_DMAAR);
+		for(i=0;i<32768;i++) {
+			outw(0x5a5a, SEEQ_BUFFER);
+		}
+		j=jiffies+HZ;
+		while ( ((inw(SEEQ_STATUS) & SEEQSTAT_FIFO_EMPTY) != SEEQSTAT_FIFO_EMPTY) && time_before(jiffies, j) )
+			mb();
+		outw( 0 , SEEQ_DMAAR);
+		while ( ((inw(SEEQ_STATUS) & SEEQSTAT_WINDOW_INT) != SEEQSTAT_WINDOW_INT) && time_before(jiffies, j+HZ))
+			mb();
+		if ( (inw(SEEQ_STATUS) & SEEQSTAT_WINDOW_INT) == SEEQSTAT_WINDOW_INT)
+			outw( SEEQCMD_WINDOW_INT_ACK | (inw(SEEQ_STATUS)& SEEQCMD_INT_MASK), SEEQ_CMD);
+		outw( SEEQCMD_FIFO_READ | SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
+		j=0;
+		for(i=0;i<32768;i++) {
+			if (inw(SEEQ_BUFFER) != 0x5a5a)
+				j++;
+		}
+		if (j) {
+			printk("%i\n",j);
+		} else {
+			printk("ok.\n");
+		}
+	}
+#endif
+
+	if (net_debug  &&  version_printed++ == 0)
+		printk(version);
+
+	printk("%s: %s found at %#3x, ", dev->name, "seeq8005", ioaddr);
+
+	/* Fill in the 'dev' fields. */
+	dev->base_addr = ioaddr;
+	dev->irq = irq;
+
+	/* Retrieve and print the ethernet address. */
+	for (i = 0; i < 6; i++)
+		printk(" %2.2x", dev->dev_addr[i] = SA_prom[i+6]);
+
+	if (dev->irq == 0xff)
+		;			/* Do nothing: a user-level program will set it. */
+	else if (dev->irq < 2) {	/* "Auto-IRQ" */
+		unsigned long cookie = probe_irq_on();
+		
+		outw( SEEQCMD_RX_INT_EN | SEEQCMD_SET_RX_ON | SEEQCMD_SET_RX_OFF, SEEQ_CMD );
+
+		dev->irq = probe_irq_off(cookie);
+		
+		if (net_debug >= 2)
+			printk(" autoirq is %d\n", dev->irq);
+	} else if (dev->irq == 2)
+	  /* Fixup for users that don't know that IRQ 2 is really IRQ 9,
+	   * or don't know which one to set. 
+	   */
+	  dev->irq = 9;
+
+#if 0
+	{
+		 int irqval = request_irq(dev->irq, &seeq8005_interrupt, 0, "seeq8005", dev);
+		 if (irqval) {
+			 printk ("%s: unable to get IRQ %d (irqval=%d).\n", dev->name,
+					 dev->irq, irqval);
+			 retval = -EAGAIN;
+			 goto out;
+		 }
+	}
+#endif
+	dev->open		= seeq8005_open;
+	dev->stop		= seeq8005_close;
+	dev->hard_start_xmit 	= seeq8005_send_packet;
+	dev->tx_timeout		= seeq8005_timeout;
+	dev->watchdog_timeo	= HZ/20;
+	dev->get_stats		= seeq8005_get_stats;
+	dev->set_multicast_list = set_multicast_list;
+	dev->flags &= ~IFF_MULTICAST;
+
+	return 0;
+out:
+	release_region(ioaddr, SEEQ8005_IO_EXTENT);
+	return retval;
+}
+
+
+/* Open/initialize the board.  This is called (in the current kernel)
+   sometime after booting when the 'ifconfig' program is run.
+
+   This routine should set everything up anew at each open, even
+   registers that "should" only need to be set once at boot, so that
+   there is non-reboot way to recover if something goes wrong.
+   */
+static int seeq8005_open(struct net_device *dev)
+{
+	struct net_local *lp = netdev_priv(dev);
+
+	{
+		 int irqval = request_irq(dev->irq, &seeq8005_interrupt, 0, "seeq8005", dev);
+		 if (irqval) {
+			 printk ("%s: unable to get IRQ %d (irqval=%d).\n", dev->name,
+					 dev->irq, irqval);
+			 return -EAGAIN;
+		 }
+	}
+
+	/* Reset the hardware here.  Don't forget to set the station address. */
+	seeq8005_init(dev, 1);
+
+	lp->open_time = jiffies;
+
+	netif_start_queue(dev);
+	return 0;
+}
+
+static void seeq8005_timeout(struct net_device *dev)
+{
+	int ioaddr = dev->base_addr;
+	printk(KERN_WARNING "%s: transmit timed out, %s?\n", dev->name,
+		   tx_done(dev) ? "IRQ conflict" : "network cable problem");
+	/* Try to restart the adaptor. */
+	seeq8005_init(dev, 1);
+	dev->trans_start = jiffies;
+	netif_wake_queue(dev);
+}
+
+static int seeq8005_send_packet(struct sk_buff *skb, struct net_device *dev)
+{
+	struct net_local *lp = netdev_priv(dev);
+	short length = skb->len;
+	unsigned char *buf;
+
+	if (length < ETH_ZLEN) {
+		skb = skb_padto(skb, ETH_ZLEN);
+		if (skb == NULL)
+			return 0;
+		length = ETH_ZLEN;
+	}
+	buf = skb->data;
+
+	/* Block a timer-based transmit from overlapping */
+	netif_stop_queue(dev);
+	
+	hardware_send_packet(dev, buf, length); 
+	dev->trans_start = jiffies;
+	lp->stats.tx_bytes += length;
+	dev_kfree_skb (skb);
+	/* You might need to clean up and record Tx statistics here. */
+
+	return 0;
+}
+
+/*
+ * wait_for_buffer
+ *
+ * This routine waits for the SEEQ chip to assert that the FIFO is ready
+ * by checking for a window interrupt, and then clearing it. This has to
+ * occur in the interrupt handler!
+ */
+inline void wait_for_buffer(struct net_device * dev)
+{
+	int ioaddr = dev->base_addr;
+	unsigned long tmp;
+	int status;
+	
+	tmp = jiffies + HZ;
+	while ( ( ((status=inw(SEEQ_STATUS)) & SEEQSTAT_WINDOW_INT) != SEEQSTAT_WINDOW_INT) && time_before(jiffies, tmp))
+		cpu_relax();
+		
+	if ( (status & SEEQSTAT_WINDOW_INT) == SEEQSTAT_WINDOW_INT)
+		outw( SEEQCMD_WINDOW_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
+}
+
+/* The typical workload of the driver:
+   Handle the network interface interrupts. */
+static irqreturn_t seeq8005_interrupt(int irq, void *dev_id, struct pt_regs * regs)
+{
+	struct net_device *dev = dev_id;
+	struct net_local *lp;
+	int ioaddr, status, boguscount = 0;
+	int handled = 0;
+
+	ioaddr = dev->base_addr;
+	lp = netdev_priv(dev);
+
+	status = inw(SEEQ_STATUS);
+	do {
+		if (net_debug >2) {
+			printk("%s: int, status=0x%04x\n",dev->name,status);
+		}
+		
+		if (status & SEEQSTAT_WINDOW_INT) {
+			handled = 1;
+			outw( SEEQCMD_WINDOW_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
+			if (net_debug) {
+				printk("%s: window int!\n",dev->name);
+			}
+		}
+		if (status & SEEQSTAT_TX_INT) {
+			handled = 1;
+			outw( SEEQCMD_TX_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
+			lp->stats.tx_packets++;
+			netif_wake_queue(dev);	/* Inform upper layers. */
+		}
+		if (status & SEEQSTAT_RX_INT) {
+			handled = 1;
+			/* Got a packet(s). */
+			seeq8005_rx(dev);
+		}
+		status = inw(SEEQ_STATUS);
+	} while ( (++boguscount < 10) && (status & SEEQSTAT_ANY_INT)) ;
+
+	if(net_debug>2) {
+		printk("%s: eoi\n",dev->name);
+	}
+	return IRQ_RETVAL(handled);
+}
+
+/* We have a good packet(s), get it/them out of the buffers. */
+static void seeq8005_rx(struct net_device *dev)
+{
+	struct net_local *lp = netdev_priv(dev);
+	int boguscount = 10;
+	int pkt_hdr;
+	int ioaddr = dev->base_addr;
+
+	do {
+		int next_packet;
+		int pkt_len;
+		int i;
+		int status;
+
+		status = inw(SEEQ_STATUS);
+	  	outw( lp->receive_ptr, SEEQ_DMAAR);
+		outw(SEEQCMD_FIFO_READ | SEEQCMD_RX_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
+	  	wait_for_buffer(dev);
+	  	next_packet = ntohs(inw(SEEQ_BUFFER));
+	  	pkt_hdr = inw(SEEQ_BUFFER);
+	  	
+		if (net_debug>2) {
+			printk("%s: 0x%04x recv next=0x%04x, hdr=0x%04x\n",dev->name,lp->receive_ptr,next_packet,pkt_hdr);
+		}
+			
+		if ((next_packet == 0) || ((pkt_hdr & SEEQPKTH_CHAIN)==0)) {	/* Read all the frames? */
+			return;							/* Done for now */
+		}
+			
+		if ((pkt_hdr & SEEQPKTS_DONE)==0)
+			break;
+			
+		if (next_packet < lp->receive_ptr) {
+			pkt_len = (next_packet + 0x10000 - ((DEFAULT_TEA+1)<<8)) - lp->receive_ptr - 4;
+		} else {
+			pkt_len = next_packet - lp->receive_ptr - 4;
+		}
+		
+		if (next_packet < ((DEFAULT_TEA+1)<<8)) {			/* is the next_packet address sane? */
+			printk("%s: recv packet ring corrupt, resetting board\n",dev->name);
+			seeq8005_init(dev,1);
+			return;
+		}
+		
+		lp->receive_ptr = next_packet;
+		
+		if (net_debug>2) {
+			printk("%s: recv len=0x%04x\n",dev->name,pkt_len);
+		}
+
+		if (pkt_hdr & SEEQPKTS_ANY_ERROR) {				/* There was an error. */
+			lp->stats.rx_errors++;
+			if (pkt_hdr & SEEQPKTS_SHORT) lp->stats.rx_frame_errors++;
+			if (pkt_hdr & SEEQPKTS_DRIB) lp->stats.rx_frame_errors++;
+			if (pkt_hdr & SEEQPKTS_OVERSIZE) lp->stats.rx_over_errors++;
+			if (pkt_hdr & SEEQPKTS_CRC_ERR) lp->stats.rx_crc_errors++;
+			/* skip over this packet */
+			outw( SEEQCMD_FIFO_WRITE | SEEQCMD_DMA_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
+			outw( (lp->receive_ptr & 0xff00)>>8, SEEQ_REA);
+		} else {
+			/* Malloc up new buffer. */
+			struct sk_buff *skb;
+			unsigned char *buf;
+
+			skb = dev_alloc_skb(pkt_len);
+			if (skb == NULL) {
+				printk("%s: Memory squeeze, dropping packet.\n", dev->name);
+				lp->stats.rx_dropped++;
+				break;
+			}
+			skb->dev = dev;
+			skb_reserve(skb, 2);	/* align data on 16 byte */
+			buf = skb_put(skb,pkt_len);
+			
+			insw(SEEQ_BUFFER, buf, (pkt_len + 1) >> 1);
+			
+			if (net_debug>2) {
+				char * p = buf;
+				printk("%s: recv ",dev->name);
+				for(i=0;i<14;i++) {
+					printk("%02x ",*(p++)&0xff);
+				}
+				printk("\n");
+			}
+
+			skb->protocol=eth_type_trans(skb,dev);
+			netif_rx(skb);
+			dev->last_rx = jiffies;
+			lp->stats.rx_packets++;
+			lp->stats.rx_bytes += pkt_len;
+		}
+	} while ((--boguscount) && (pkt_hdr & SEEQPKTH_CHAIN));
+
+	/* If any worth-while packets have been received, netif_rx()
+	   has done a mark_bh(NET_BH) for us and will work on them
+	   when we get to the bottom-half routine. */
+	return;
+}
+
+/* The inverse routine to net_open(). */
+static int seeq8005_close(struct net_device *dev)
+{
+	struct net_local *lp = netdev_priv(dev);
+	int ioaddr = dev->base_addr;
+
+	lp->open_time = 0;
+
+	netif_stop_queue(dev);
+	
+	/* Flush the Tx and disable Rx here. */
+	outw( SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
+
+	free_irq(dev->irq, dev);
+
+	/* Update the statistics here. */
+
+	return 0;
+
+}
+
+/* Get the current statistics.	This may be called with the card open or
+   closed. */
+static struct net_device_stats *seeq8005_get_stats(struct net_device *dev)
+{
+	struct net_local *lp = netdev_priv(dev);
+
+	return &lp->stats;
+}
+
+/* Set or clear the multicast filter for this adaptor.
+   num_addrs == -1	Promiscuous mode, receive all packets
+   num_addrs == 0	Normal mode, clear multicast list
+   num_addrs > 0	Multicast mode, receive normal and MC packets, and do
+			best-effort filtering.
+ */
+static void set_multicast_list(struct net_device *dev)
+{
+/*
+ * I _could_ do up to 6 addresses here, but won't (yet?)
+ */
+
+#if 0
+	int ioaddr = dev->base_addr;
+/*
+ * hmm, not even sure if my matching works _anyway_ - seem to be receiving
+ * _everything_ . . .
+ */
+ 
+	if (num_addrs) {			/* Enable promiscuous mode */
+		outw( (inw(SEEQ_CFG1) & ~SEEQCFG1_MATCH_MASK)| SEEQCFG1_MATCH_ALL,  SEEQ_CFG1);
+		dev->flags|=IFF_PROMISC;
+	} else {				/* Disable promiscuous mode, use normal mode */
+		outw( (inw(SEEQ_CFG1) & ~SEEQCFG1_MATCH_MASK)| SEEQCFG1_MATCH_BROAD, SEEQ_CFG1);
+	}
+#endif
+}
+
+void seeq8005_init(struct net_device *dev, int startp)
+{
+	struct net_local *lp = netdev_priv(dev);
+	int ioaddr = dev->base_addr;
+	int i;
+	
+	outw(SEEQCFG2_RESET, SEEQ_CFG2);	/* reset device */
+	udelay(5);
+	
+	outw( SEEQCMD_FIFO_WRITE | SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
+	outw( 0, SEEQ_DMAAR);			/* load start address into both low and high byte */
+/*	wait_for_buffer(dev); */		/* I think that you only need a wait for memory buffer */
+	outw( SEEQCFG1_BUFFER_MAC0, SEEQ_CFG1);
+	
+	for(i=0;i<6;i++) {			/* set Station address */
+		outb(dev->dev_addr[i], SEEQ_BUFFER);
+		udelay(2);
+	}
+	
+	outw( SEEQCFG1_BUFFER_TEA, SEEQ_CFG1);	/* set xmit end area pointer to 16K */
+	outb( DEFAULT_TEA, SEEQ_BUFFER);	/* this gives us 16K of send buffer and 48K of recv buffer */
+	
+	lp->receive_ptr = (DEFAULT_TEA+1)<<8;	/* so we can find our packet_header */
+	outw( lp->receive_ptr, SEEQ_RPR);	/* Receive Pointer Register is set to recv buffer memory */
+	
+	outw( 0x00ff, SEEQ_REA);		/* Receive Area End */
+
+	if (net_debug>4) {
+		printk("%s: SA0 = ",dev->name);
+
+		outw( SEEQCMD_FIFO_READ | SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
+		outw( 0, SEEQ_DMAAR);
+		outw( SEEQCFG1_BUFFER_MAC0, SEEQ_CFG1);
+		
+		for(i=0;i<6;i++) {
+			printk("%02x ",inb(SEEQ_BUFFER));
+		}
+		printk("\n");
+	}
+	
+	outw( SEEQCFG1_MAC0_EN | SEEQCFG1_MATCH_BROAD | SEEQCFG1_BUFFER_BUFFER, SEEQ_CFG1);
+	outw( SEEQCFG2_AUTO_REA | SEEQCFG2_CTRLO, SEEQ_CFG2);
+	outw( SEEQCMD_SET_RX_ON | SEEQCMD_TX_INT_EN | SEEQCMD_RX_INT_EN, SEEQ_CMD);
+
+	if (net_debug>4) {
+		int old_cfg1;
+		old_cfg1 = inw(SEEQ_CFG1);
+		printk("%s: stat = 0x%04x\n",dev->name,inw(SEEQ_STATUS));
+		printk("%s: cfg1 = 0x%04x\n",dev->name,old_cfg1);
+		printk("%s: cfg2 = 0x%04x\n",dev->name,inw(SEEQ_CFG2));
+		printk("%s: raer = 0x%04x\n",dev->name,inw(SEEQ_REA));
+		printk("%s: dmaar= 0x%04x\n",dev->name,inw(SEEQ_DMAAR));
+		
+	}
+}	
+
+
+static void hardware_send_packet(struct net_device * dev, char *buf, int length)
+{
+	int ioaddr = dev->base_addr;
+	int status = inw(SEEQ_STATUS);
+	int transmit_ptr = 0;
+	int tmp;
+
+	if (net_debug>4) {
+		printk("%s: send 0x%04x\n",dev->name,length);
+	}
+	
+	/* Set FIFO to writemode and set packet-buffer address */
+	outw( SEEQCMD_FIFO_WRITE | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
+	outw( transmit_ptr, SEEQ_DMAAR);
+	
+	/* output SEEQ Packet header barfage */
+	outw( htons(length + 4), SEEQ_BUFFER);
+	outw( SEEQPKTH_XMIT | SEEQPKTH_DATA_FOLLOWS | SEEQPKTH_XMIT_INT_EN, SEEQ_BUFFER );
+	
+	/* blat the buffer */
+	outsw( SEEQ_BUFFER, buf, (length +1) >> 1);
+	/* paranoia !! */
+	outw( 0, SEEQ_BUFFER);
+	outw( 0, SEEQ_BUFFER);
+	
+	/* set address of start of transmit chain */
+	outw( transmit_ptr, SEEQ_TPR);
+	
+	/* drain FIFO */
+	tmp = jiffies;
+	while ( (((status=inw(SEEQ_STATUS)) & SEEQSTAT_FIFO_EMPTY) == 0) && (jiffies - tmp < HZ))
+		mb();
+	
+	/* doit ! */
+	outw( SEEQCMD_WINDOW_INT_ACK | SEEQCMD_SET_TX_ON | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
+	
+}
+
+
+#ifdef MODULE
+
+static struct net_device *dev_seeq;
+MODULE_LICENSE("GPL");
+module_param(io, int, 0);
+module_param(irq, int, 0);
+MODULE_PARM_DESC(io, "SEEQ 8005 I/O base address");
+MODULE_PARM_DESC(irq, "SEEQ 8005 IRQ number");
+
+int init_module(void)
+{
+	dev_seeq = seeq8005_probe(-1);
+	if (IS_ERR(dev_seeq))
+		return PTR_ERR(dev_seeq);
+	return 0;
+}
+
+void cleanup_module(void)
+{
+	unregister_netdev(dev_seeq);
+	release_region(dev_seeq->base_addr, SEEQ8005_IO_EXTENT);
+	free_netdev(dev_seeq);
+}
+
+#endif /* MODULE */
+
+/*
+ * Local variables:
+ *  compile-command: "gcc -D__KERNEL__ -I/usr/src/linux/net/inet -Wall -Wstrict-prototypes -O6 -m486 -c skeleton.c"
+ *  version-control: t
+ *  kept-new-versions: 5
+ *  tab-width: 4
+ * End:
+ */