stmmac: support Reg_9 to get HW level information

For GMAC newer than 3.40a there is a new register (Reg_9) that provides the
status of all modules of the transmit and receive paths and FIFO status.
These can be exposed via ethtool.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 42 insertions, 0 deletions

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h b/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
index b3fe0575ff6b..8831a053ac13 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
@@ -34,6 +34,7 @@
 #define GMAC_FLOW_CTRL		0x00000018	/* Flow Control */
 #define GMAC_VLAN_TAG		0x0000001c	/* VLAN Tag */
 #define GMAC_VERSION		0x00000020	/* GMAC CORE Version */
+#define GMAC_DEBUG		0x00000024	/* GMAC debug register */
 #define GMAC_WAKEUP_FILTER	0x00000028	/* Wake-up Frame Filter */
 
 #define GMAC_INT_STATUS		0x00000038	/* interrupt status register */
@@ -177,6 +178,47 @@ enum inter_frame_gap {
 #define GMAC_FLOW_CTRL_TFE	0x00000002	/* Tx Flow Control Enable */
 #define GMAC_FLOW_CTRL_FCB_BPA	0x00000001	/* Flow Control Busy ... */
 
+/* DEBUG Register defines */
+/* MTL TxStatus FIFO */
+#define GMAC_DEBUG_TXSTSFSTS	BIT(25)	/* MTL TxStatus FIFO Full Status */
+#define GMAC_DEBUG_TXFSTS	BIT(24) /* MTL Tx FIFO Not Empty Status */
+#define GMAC_DEBUG_TWCSTS	BIT(22) /* MTL Tx FIFO Write Controller */
+/* MTL Tx FIFO Read Controller Status */
+#define GMAC_DEBUG_TRCSTS_MASK	GENMASK(21, 20)
+#define GMAC_DEBUG_TRCSTS_SHIFT	20
+#define GMAC_DEBUG_TRCSTS_IDLE	0
+#define GMAC_DEBUG_TRCSTS_READ	1
+#define GMAC_DEBUG_TRCSTS_TXW	2
+#define GMAC_DEBUG_TRCSTS_WRITE	3
+#define GMAC_DEBUG_TXPAUSED	BIT(19) /* MAC Transmitter in PAUSE */
+/* MAC Transmit Frame Controller Status */
+#define GMAC_DEBUG_TFCSTS_MASK	GENMASK(18, 17)
+#define GMAC_DEBUG_TFCSTS_SHIFT	17
+#define GMAC_DEBUG_TFCSTS_IDLE	0
+#define GMAC_DEBUG_TFCSTS_WAIT	1
+#define GMAC_DEBUG_TFCSTS_GEN_PAUSE	2
+#define GMAC_DEBUG_TFCSTS_XFER	3
+/* MAC GMII or MII Transmit Protocol Engine Status */
+#define GMAC_DEBUG_TPESTS	BIT(16)
+#define GMAC_DEBUG_RXFSTS_MASK	GENMASK(9, 8) /* MTL Rx FIFO Fill-level */
+#define GMAC_DEBUG_RXFSTS_SHIFT	8
+#define GMAC_DEBUG_RXFSTS_EMPTY	0
+#define GMAC_DEBUG_RXFSTS_BT	1
+#define GMAC_DEBUG_RXFSTS_AT	2
+#define GMAC_DEBUG_RXFSTS_FULL	3
+#define GMAC_DEBUG_RRCSTS_MASK	GENMASK(6, 5) /* MTL Rx FIFO Read Controller */
+#define GMAC_DEBUG_RRCSTS_SHIFT	5
+#define GMAC_DEBUG_RRCSTS_IDLE	0
+#define GMAC_DEBUG_RRCSTS_RDATA	1
+#define GMAC_DEBUG_RRCSTS_RSTAT	2
+#define GMAC_DEBUG_RRCSTS_FLUSH	3
+#define GMAC_DEBUG_RWCSTS	BIT(4) /* MTL Rx FIFO Write Controller Active */
+/* MAC Receive Frame Controller FIFO Status */
+#define GMAC_DEBUG_RFCFCSTS_MASK	GENMASK(2, 1)
+#define GMAC_DEBUG_RFCFCSTS_SHIFT	1
+/* MAC GMII or MII Receive Protocol Engine Status */
+#define GMAC_DEBUG_RPESTS	BIT(0)
+
 /*--- DMA BLOCK defines ---*/
 /* DMA Bus Mode register defines */
 #define DMA_BUS_MODE_SFT_RESET	0x00000001	/* Software Reset */