Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (22 commits)
  hwmon: (via-cputemp) Remove bogus "SHOW" global variable
  hwmon: jc42 depends on I2C
  hwmon: (pc87427) Add a maintainer
  hwmon: (pc87427) Move sysfs file removal to a separate function
  hwmon: (pc87427) Add temperature monitoring support
  hwmon: (pc87427) Add support for the second logical device
  hwmon: (pc87427) Add support for manual fan speed control
  hwmon: (pc87427) Minor style cleanups
  hwmon: (pc87427) Handle disabled fan inputs properly
  hwmon: (w83627ehf) Add support for W83667HG-B
  hwmon: (w83627ehf) Driver cleanup
  hwmon: Add driver for SMSC EMC2103 temperature monitor and fan controller
  hwmon: Remove in[0-*]_fault from sysfs-interface
  hwmon: Add 4 current alarm/beep attributes to sysfs-interface
  hwmon: Add 3 critical limit attributes to sysfs-interface
  hwmon: (asc7621) Clean up and improve detect function
  hwmon: (it87) Export labels for internal sensors
  hwmon: (lm75) Add suspend/resume feature
  hwmon: (emc1403) Add power support
  hwmon: (ltc4245) Expose all GPIO pins as analog voltages
  ...

5 files changed, 114 insertions, 14 deletions

diff --git a/Documentation/hwmon/emc2103 b/Documentation/hwmon/emc2103
new file mode 100644
index 000000000000..a12b2c127140
--- /dev/null
+++ b/Documentation/hwmon/emc2103
@@ -0,0 +1,33 @@
+Kernel driver emc2103
+======================
+
+Supported chips:
+  * SMSC EMC2103
+    Addresses scanned: I2C 0x2e
+    Prefix: 'emc2103'
+    Datasheet: Not public
+
+Authors:
+        Steve Glendinning <steve.glendinning@smsc.com>
+
+Description
+-----------
+
+The Standard Microsystems Corporation (SMSC) EMC2103 chips
+contain up to 4 temperature sensors and a single fan controller.
+
+Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
+triggered if the rotation speed has dropped below a programmable limit. Fan
+readings can be divided by a programmable divider (1, 2, 4 or 8) to give
+the readings more range or accuracy. Not all RPM values can accurately be
+represented, so some rounding is done. With a divider of 1, the lowest
+representable value is 480 RPM.
+
+This driver supports RPM based control, to use this a fan target
+should be written to fan1_target and pwm1_enable should be set to 3.
+
+The 2103-2 and 2103-4 variants have a third temperature sensor, which can
+be connected to two anti-parallel diodes.  These values can be read
+as temp3 and temp4.  If only one diode is attached to this channel, temp4
+will show as "fault".  The module parameter "apd=0" can be used to suppress
+this 4th channel when anti-parallel diodes are not fitted.
diff --git a/Documentation/hwmon/ltc4245 b/Documentation/hwmon/ltc4245
index 86b5880d8502..b478b0864965 100644
--- a/Documentation/hwmon/ltc4245
+++ b/Documentation/hwmon/ltc4245
@@ -72,9 +72,31 @@ in6_min_alarm		5v  output undervoltage alarm
 in7_min_alarm		3v  output undervoltage alarm
 in8_min_alarm		Vee (-12v) output undervoltage alarm
 
-in9_input		GPIO voltage data
+in9_input		GPIO voltage data (see note 1)
+in10_input		GPIO voltage data (see note 1)
+in11_input		GPIO voltage data (see note 1)
 
 power1_input		12v power usage (mW)
 power2_input		5v  power usage (mW)
 power3_input		3v  power usage (mW)
 power4_input		Vee (-12v) power usage (mW)
+
+
+Note 1
+------
+
+If you have NOT configured the driver to sample all GPIO pins as analog
+voltages, then the in10_input and in11_input sysfs attributes will not be
+created. The driver will sample the GPIO pin that is currently connected to the
+ADC as an analog voltage, and report the value in in9_input.
+
+If you have configured the driver to sample all GPIO pins as analog voltages,
+then they will be sampled in round-robin fashion. If userspace reads too
+slowly, -EAGAIN will be returned when you read the sysfs attribute containing
+the sensor reading.
+
+The LTC4245 chip can be configured to sample all GPIO pins with two methods:
+1) platform data -- see include/linux/i2c/ltc4245.h
+2) OF device tree -- add the "ltc4245,use-extra-gpios" property to each chip
+
+The default mode of operation is to sample a single GPIO pin.
diff --git a/Documentation/hwmon/pc87427 b/Documentation/hwmon/pc87427
index db5cc1227a83..8fdd08c9e48b 100644
--- a/Documentation/hwmon/pc87427
+++ b/Documentation/hwmon/pc87427
@@ -18,10 +18,11 @@ Description
 
 The National Semiconductor Super I/O chip includes complete hardware
 monitoring capabilities. It can monitor up to 18 voltages, 8 fans and
-6 temperature sensors. Only the fans are supported at the moment.
+6 temperature sensors. Only the fans and temperatures are supported at
+the moment, voltages aren't.
 
-This chip also has fan controlling features, which are not yet supported
-by this driver either.
+This chip also has fan controlling features (up to 4 PWM outputs),
+which are partly supported by this driver.
 
 The driver assumes that no more than one chip is present, which seems
 reasonable.
@@ -36,3 +37,23 @@ signal. Speeds down to 83 RPM can be measured.
 An alarm is triggered if the rotation speed drops below a programmable
 limit. Another alarm is triggered if the speed is too low to be measured
 (including stalled or missing fan).
+
+
+Fan Speed Control
+-----------------
+
+Fan speed can be controlled by PWM outputs. There are 4 possible modes:
+always off, always on, manual and automatic. The latter isn't supported
+by the driver: you can only return to that mode if it was the original
+setting, and the configuration interface is missing.
+
+
+Temperature Monitoring
+----------------------
+
+The PC87427 relies on external sensors (following the SensorPath
+standard), so the resolution and range depend on the type of sensor
+connected. The integer part can be 8-bit or 9-bit, and can be signed or
+not. I couldn't find a way to figure out the external sensor data
+temperature format, so user-space adjustment (typically by a factor 2)
+may be required.
diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface
index d4e2917c6f18..ff45d1f837c8 100644
--- a/Documentation/hwmon/sysfs-interface
+++ b/Documentation/hwmon/sysfs-interface
@@ -107,10 +107,24 @@ in[0-*]_min	Voltage min value.
 		Unit: millivolt
 		RW
 		
+in[0-*]_lcrit	Voltage critical min value.
+		Unit: millivolt
+		RW
+		If voltage drops to or below this limit, the system may
+		take drastic action such as power down or reset. At the very
+		least, it should report a fault.
+
 in[0-*]_max	Voltage max value.
 		Unit: millivolt
 		RW
 		
+in[0-*]_crit	Voltage critical max value.
+		Unit: millivolt
+		RW
+		If voltage reaches or exceeds this limit, the system may
+		take drastic action such as power down or reset. At the very
+		least, it should report a fault.
+
 in[0-*]_input	Voltage input value.
 		Unit: millivolt
 		RO
@@ -284,7 +298,7 @@ temp[1-*]_input Temperature input value.
 		Unit: millidegree Celsius
 		RO
 
-temp[1-*]_crit	Temperature critical value, typically greater than
+temp[1-*]_crit	Temperature critical max value, typically greater than
 		corresponding temp_max values.
 		Unit: millidegree Celsius
 		RW
@@ -296,6 +310,11 @@ temp[1-*]_crit_hyst
 		from the critical value.
 		RW
 
+temp[1-*]_lcrit	Temperature critical min value, typically lower than
+		corresponding temp_min values.
+		Unit: millidegree Celsius
+		RW
+
 temp[1-*]_offset
 		Temperature offset which is added to the temperature reading
 		by the chip.
@@ -344,9 +363,6 @@ Also see the Alarms section for status flags associated with temperatures.
 * Currents *
 ************
 
-Note that no known chip provides current measurements as of writing,
-so this part is theoretical, so to say.
-
 curr[1-*]_max	Current max value
 		Unit: milliampere
 		RW
@@ -471,6 +487,7 @@ limit-related alarms, not both. The driver should just reflect the hardware
 implementation.
 
 in[0-*]_alarm
+curr[1-*]_alarm
 fan[1-*]_alarm
 temp[1-*]_alarm
 		Channel alarm
@@ -482,6 +499,8 @@ OR
 
 in[0-*]_min_alarm
 in[0-*]_max_alarm
+curr[1-*]_min_alarm
+curr[1-*]_max_alarm
 fan[1-*]_min_alarm
 fan[1-*]_max_alarm
 temp[1-*]_min_alarm
@@ -497,7 +516,6 @@ to notify open diodes, unconnected fans etc. where the hardware
 supports it. When this boolean has value 1, the measurement for that
 channel should not be trusted.
 
-in[0-*]_fault
 fan[1-*]_fault
 temp[1-*]_fault
 		Input fault condition
@@ -513,6 +531,7 @@ beep_enable	Master beep enable
 		RW
 
 in[0-*]_beep
+curr[1-*]_beep
 fan[1-*]_beep
 temp[1-*]_beep
 		Channel beep
diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf
index b7e42ec4b26b..13d556112fc0 100644
--- a/Documentation/hwmon/w83627ehf
+++ b/Documentation/hwmon/w83627ehf
@@ -20,6 +20,10 @@ Supported chips:
     Prefix: 'w83667hg'
     Addresses scanned: ISA address retrieved from Super I/O registers
     Datasheet: not available
+  * Winbond W83667HG-B
+    Prefix: 'w83667hg'
+    Addresses scanned: ISA address retrieved from Super I/O registers
+    Datasheet: Available from Nuvoton upon request
 
 Authors:
         Jean Delvare <khali@linux-fr.org>
@@ -32,8 +36,8 @@ Description
 -----------
 
 This driver implements support for the Winbond W83627EHF, W83627EHG,
-W83627DHG, W83627DHG-P and W83667HG super I/O chips. We will refer to them
-collectively as Winbond chips.
+W83627DHG, W83627DHG-P, W83667HG and W83667HG-B super I/O chips.
+We will refer to them collectively as Winbond chips.
 
 The chips implement three temperature sensors, five fan rotation
 speed sensors, ten analog voltage sensors (only nine for the 627DHG), one
@@ -68,14 +72,15 @@ follows:
 temp1 -> pwm1
 temp2 -> pwm2
 temp3 -> pwm3
-prog  -> pwm4 (not on 667HG; the programmable setting is not supported by
-	       the driver)
+prog  -> pwm4 (not on 667HG and 667HG-B; the programmable setting is not
+	       supported by the driver)
 
 /sys files
 ----------
 
 name - this is a standard hwmon device entry. For the W83627EHF and W83627EHG,
-       it is set to "w83627ehf" and for the W83627DHG it is set to "w83627dhg"
+       it is set to "w83627ehf", for the W83627DHG it is set to "w83627dhg",
+       and for the W83667HG it is set to "w83667hg".
 
 pwm[1-4] - this file stores PWM duty cycle or DC value (fan speed) in range:
 	   0 (stop) to 255 (full)