Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC DT updates from Kevin Hilman:
 "As usual, quite a few device-tree updates in ARM land.  There was one
  minor churn in DTs due to relicensing under a dual-license, and lots
  of little additions of new peripherals, features etc, but nothing
  really exciting to call to your attention.  Some higlights, focsuing
  on support for new SoCs and boards:

   - AT91: new boards: Overkiz,  Acme Systems' Arietta G25
   - tegra: HDA support
   - bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS
     RT-AC87U
   - mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
     boards, DLink DNS-327L
   - OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill
     SL50
   - ARM: added support for Juno r1 board
   - sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33,
     Mele A1000G
   - imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
     Gateworks GW5510, and aristainetos2 boards
   - hisilicon: hi6220 SoC support; new boards: 96boards hikey"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (462 commits)
  ARM: hisi: revert changes from hisi/hip04-dt branch
  ARM: nomadik: set proper compatible for accelerometer
  ARM64: juno: add GPIO keys
  ARM: at91/dt: sama5d4: fix dma conf for aes, sha and tdes nodes
  ARM: dts: Introduce STM32F429 MCU
  ARM: socfpga: dts: enable ethernet for Arria10 devkit
  ARM: dts: k2l: fix the netcp range size
  ARM: dts: k2e: fix the netcp range size
  ARM: dts: k2hk: fix the netcp range size
  ARM: dts: k2l-evm: Add device bindings for netcp driver
  ARM: dts: k2e-evm: Add device bindings for netcp driver
  ARM: dts: k2hk-evm: Add device bindings for netcp driver
  ARM: BCM5301X: Add DT for Asus RT-AC87U
  ARM: BCM5301X: add IRQ numbers for PCIe controller
  ARM: BCM5301X: add NAND flash chip description
  arm64: dts: Add dts files for Hisilicon Hi6220 SoC
  clk: hi6220: Document devicetree bindings for hi6220 clock
  arm64: hi6220: Document devicetree bindings for Hisilicon hi6220 SoC
  ARM: at91/dt: sama5d4ek: mci0 uses slot 0
  ARM: at91/dt: kizbox: fix mismatch LED PWM device
  ...

21 files changed, 631 insertions, 83 deletions

diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-controller.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-controller.txt
new file mode 100644
index 000000000000..77ca635765e1
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-controller.txt
@@ -0,0 +1,12 @@
+Altera SOCFPGA SDRAM Controller
+
+Required properties:
+- compatible : Should contain "altr,sdr-ctl" and "syscon".
+  syscon is required by the Altera SOCFPGA SDRAM EDAC.
+- reg : Should contain 1 register range (address and length)
+
+Example:
+	sdr: sdr@ffc25000 {
+		compatible = "altr,sdr-ctl", "syscon";
+		reg = <0xffc25000 0x1000>;
+	};
diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards
index b78564b2b201..1a709970e7f7 100644
--- a/Documentation/devicetree/bindings/arm/arm-boards
+++ b/Documentation/devicetree/bindings/arm/arm-boards
@@ -157,3 +157,69 @@ Example:
 
 	};
 };
+
+ARM Versatile Express Boards
+-----------------------------
+For details on the device tree bindings for ARM Versatile Express boards
+please consult the vexpress.txt file in the same directory as this file.
+
+ARM Juno Boards
+----------------
+The Juno boards are targeting development for AArch64 systems. The first
+iteration, Juno r0, is a vehicle for evaluating big.LITTLE on AArch64,
+with the second iteration, Juno r1, mainly aimed at development of PCIe
+based systems. Juno r1 also has support for AXI masters placed on the TLX
+connectors to join the coherency domain.
+
+Juno boards are described in a similar way to ARM Versatile Express boards,
+with the motherboard part of the hardware being described in a separate file
+to highlight the fact that is part of the support infrastructure for the SoC.
+Juno device tree bindings also share the Versatile Express bindings as
+described under the RS1 memory mapping.
+
+Required properties (in root node):
+	compatible = "arm,juno";	/* For Juno r0 board */
+	compatible = "arm,juno-r1";	/* For Juno r1 board */
+
+Required nodes:
+The description for the board must include:
+   - a "psci" node describing the boot method used for the secondary CPUs.
+     A detailed description of the bindings used for "psci" nodes is present
+     in the psci.txt file.
+   - a "cpus" node describing the available cores and their associated
+     "enable-method"s. For more details see cpus.txt file.
+
+Example:
+
+/dts-v1/;
+/ {
+	model = "ARM Juno development board (r0)";
+	compatible = "arm,juno", "arm,vexpress";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		A57_0: cpu@0 {
+			compatible = "arm,cortex-a57","arm,armv8";
+			reg = <0x0 0x0>;
+			device_type = "cpu";
+			enable-method = "psci";
+		};
+
+		.....
+
+		A53_0: cpu@100 {
+			compatible = "arm,cortex-a53","arm,armv8";
+			reg = <0x0 0x100>;
+			device_type = "cpu";
+			enable-method = "psci";
+		};
+
+		.....
+	};
+
+};
diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
index ac683480c486..c78576bb7729 100644
--- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
+++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
@@ -1,8 +1,35 @@
 Broadcom BCM2835 device tree bindings
 -------------------------------------------
 
-Boards with the BCM2835 SoC shall have the following properties:
+Raspberry Pi Model A
+Required root node properties:
+compatible = "raspberrypi,model-a", "brcm,bcm2835";
 
-Required root node property:
+Raspberry Pi Model A+
+Required root node properties:
+compatible = "raspberrypi,model-a-plus", "brcm,bcm2835";
 
+Raspberry Pi Model B
+Required root node properties:
+compatible = "raspberrypi,model-b", "brcm,bcm2835";
+
+Raspberry Pi Model B (no P5)
+early model B with I2C0 rather than I2C1 routed to the expansion header
+Required root node properties:
+compatible = "raspberrypi,model-b-i2c0", "brcm,bcm2835";
+
+Raspberry Pi Model B rev2
+Required root node properties:
+compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835";
+
+Raspberry Pi Model B+
+Required root node properties:
+compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
+
+Raspberry Pi Compute Module
+Required root node properties:
+compatible = "raspberrypi,compute-module", "brcm,bcm2835";
+
+Generic BCM2835 board
+Required root node properties:
 compatible = "brcm,bcm2835";
diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt
index bd49987a8812..b82b6a0ae6f7 100644
--- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt
+++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt
@@ -7,3 +7,79 @@ following properties:
 Required root node property:
 
 compatible: should be "brcm,bcm63138"
+
+An optional Boot lookup table Device Tree node is required for secondary CPU
+initialization as well as a 'resets' phandle to the correct PMB controller as
+defined in reset/brcm,bcm63138-pmb.txt for this secondary CPU, and an
+'enable-method' property.
+
+Required properties for the Boot lookup table node:
+- compatible: should be "brcm,bcm63138-bootlut"
+- reg: register base address and length for the Boot Lookup table
+
+Optional properties for the primary CPU node:
+- enable-method: should be "brcm,bcm63138"
+
+Optional properties for the secondary CPU node:
+- enable-method: should be "brcm,bcm63138"
+- resets: phandle to the relevant PMB controller, one integer indicating the internal
+  bus number, and a second integer indicating the address of the CPU in the PMB
+  internal bus number.
+
+Example:
+
+	cpus {
+		cpu@0 {
+			compatible = "arm,cotex-a9";
+			reg = <0>;
+			...
+			enable-method = "brcm,bcm63138";
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a9";
+			reg = <1>;
+			...
+			enable-method = "brcm,bcm63138";
+			resets = <&pmb0 4 1>;
+		};
+	};
+
+	bootlut: bootlut@8000 {
+		compatible = "brcm,bcm63138-bootlut";
+		reg = <0x8000 0x50>;
+	};
+
+=======
+reboot
+------
+Two nodes are required for software reboot: a timer node and a syscon-reboot node.
+
+Timer node:
+
+- compatible: Must be "brcm,bcm6328-timer", "syscon"
+- reg: Register base address and length
+
+Syscon reboot node:
+
+See Documentation/devicetree/bindings/power/reset/syscon-reboot.txt for the
+detailed list of properties, the two values defined below are specific to the
+BCM6328-style timer:
+
+- offset: Should be 0x34 to denote the offset of the TIMER_WD_TIMER_RESET register
+  from the beginning of the TIMER block
+- mask: Should be 1 for the SoftRst bit.
+
+Example:
+
+	timer: timer@80 {
+		compatible = "brcm,bcm6328-timer", "syscon";
+		reg = <0x80 0x3c>;
+	};
+
+	reboot {
+		compatible = "syscon-reboot";
+		regmap = <&timer>;
+		offset = <0x34>;
+		mask = <0x1>;
+	};
diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
index 35b1bd49cfa1..c431c67524d6 100644
--- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
+++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
@@ -1,5 +1,8 @@
 Hisilicon Platforms Device Tree Bindings
 ----------------------------------------------------
+Hi6220 SoC
+Required root node properties:
+	- compatible = "hisilicon,hi6220";
 
 Hi4511 Board
 Required root node properties:
@@ -13,6 +16,9 @@ HiP01 ca9x2 Board
 Required root node properties:
 	- compatible = "hisilicon,hip01-ca9x2";
 
+HiKey Board
+Required root node properties:
+	- compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220";
 
 Hisilicon system controller
 
@@ -41,6 +47,87 @@ Example:
 	};
 
 -----------------------------------------------------------------------
+Hisilicon Hi6220 system controller
+
+Required properties:
+- compatible : "hisilicon,hi6220-sysctrl"
+- reg : Register address and size
+- #clock-cells: should be set to 1, many clock registers are defined
+  under this controller and this property must be present.
+
+Hisilicon designs this controller as one of the system controllers,
+its main functions are the same as Hisilicon system controller, but
+the register offset of some core modules are different.
+
+Example:
+	/*for Hi6220*/
+	sys_ctrl: sys_ctrl@f7030000 {
+		compatible = "hisilicon,hi6220-sysctrl", "syscon";
+		reg = <0x0 0xf7030000 0x0 0x2000>;
+		#clock-cells = <1>;
+	};
+
+
+Hisilicon Hi6220 Power Always ON domain controller
+
+Required properties:
+- compatible : "hisilicon,hi6220-aoctrl"
+- reg : Register address and size
+- #clock-cells: should be set to 1, many clock registers are defined
+  under this controller and this property must be present.
+
+Hisilicon designs this system controller to control the power always
+on domain for mobile platform.
+
+Example:
+	/*for Hi6220*/
+	ao_ctrl: ao_ctrl@f7800000 {
+		compatible = "hisilicon,hi6220-aoctrl", "syscon";
+		reg = <0x0 0xf7800000 0x0 0x2000>;
+		#clock-cells = <1>;
+	};
+
+
+Hisilicon Hi6220 Media domain controller
+
+Required properties:
+- compatible : "hisilicon,hi6220-mediactrl"
+- reg : Register address and size
+- #clock-cells: should be set to 1, many clock registers are defined
+  under this controller and this property must be present.
+
+Hisilicon designs this system controller to control the multimedia
+domain(e.g. codec, G3D ...) for mobile platform.
+
+Example:
+	/*for Hi6220*/
+	media_ctrl: media_ctrl@f4410000 {
+		compatible = "hisilicon,hi6220-mediactrl", "syscon";
+		reg = <0x0 0xf4410000 0x0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+
+Hisilicon Hi6220 Power Management domain controller
+
+Required properties:
+- compatible : "hisilicon,hi6220-pmctrl"
+- reg : Register address and size
+- #clock-cells: should be set to 1, some clock registers are define
+  under this controller and this property must be present.
+
+Hisilicon designs this system controller to control the power management
+domain for mobile platform.
+
+Example:
+	/*for Hi6220*/
+	pm_ctrl: pm_ctrl@f7032000 {
+		compatible = "hisilicon,hi6220-pmctrl", "syscon";
+		reg = <0x0 0xf7032000 0x0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+-----------------------------------------------------------------------
 Hisilicon HiP01 system controller
 
 Required properties:
diff --git a/Documentation/devicetree/bindings/arm/marvell,berlin.txt b/Documentation/devicetree/bindings/arm/marvell,berlin.txt
index a99eb9eb14c0..3bab18409b7a 100644
--- a/Documentation/devicetree/bindings/arm/marvell,berlin.txt
+++ b/Documentation/devicetree/bindings/arm/marvell,berlin.txt
@@ -1,6 +1,18 @@
 Marvell Berlin SoC Family Device Tree Bindings
 ---------------------------------------------------------------
 
+Work in progress statement:
+
+Device tree files and bindings applying to Marvell Berlin SoCs and boards are
+considered "unstable". Any Marvell Berlin device tree binding may change at any
+time. Be sure to use a device tree binary and a kernel image generated from the
+same source tree.
+
+Please refer to Documentation/devicetree/bindings/ABI.txt for a definition of a
+stable binding/ABI.
+
+---------------------------------------------------------------
+
 Boards with a SoC of the Marvell Berlin family, e.g. Armada 1500
 shall have the following properties:
 
@@ -49,10 +61,9 @@ chip control registers, so there should be a single DT node only providing the
 different functions which are described below.
 
 Required properties:
-- compatible: shall be one of
-	"marvell,berlin2-chip-ctrl" for BG2
-	"marvell,berlin2cd-chip-ctrl" for BG2CD
-	"marvell,berlin2q-chip-ctrl" for BG2Q
+- compatible:
+	* the first and second values must be:
+		"simple-mfd", "syscon"
 - reg: address and length of following register sets for
   BG2/BG2CD: chip control register set
   BG2Q: chip control register set and cpu pll registers
@@ -63,90 +74,23 @@ Marvell Berlin SoCs have a system control register set providing several
 individual registers dealing with pinmux, padmux, and reset.
 
 Required properties:
-- compatible: should be one of
-	"marvell,berlin2-system-ctrl" for BG2
-	"marvell,berlin2cd-system-ctrl" for BG2CD
-	"marvell,berlin2q-system-ctrl" for BG2Q
+- compatible:
+	* the first and second values must be:
+		"simple-mfd", "syscon"
 - reg: address and length of the system control register set
 
-* Clock provider binding
-
-As clock related registers are spread among the chip control registers, the
-chip control node also provides the clocks. Marvell Berlin2 (BG2, BG2CD, BG2Q)
-SoCs share the same IP for PLLs and clocks, with some minor differences in
-features and register layout.
-
-Required properties:
-- #clock-cells: shall be set to 1
-- clocks: clock specifiers referencing the core clock input clocks
-- clock-names: array of strings describing the input clock specifiers above.
-    Allowed clock-names for the reference clocks are
-      "refclk" for the SoCs osciallator input on all SoCs,
-    and SoC-specific input clocks for
-      BG2/BG2CD: "video_ext0" for the external video clock input
-
-Clocks provided by core clocks shall be referenced by a clock specifier
-indexing one of the provided clocks. Refer to dt-bindings/clock/berlin<soc>.h
-for the corresponding index mapping.
-
-* Pin controller binding
-
-Pin control registers are part of both register sets, chip control and system
-control. The pins controlled are organized in groups, so no actual pin
-information is needed.
-
-A pin-controller node should contain subnodes representing the pin group
-configurations, one per function. Each subnode has the group name and the muxing
-function used.
-
-Be aware the Marvell Berlin datasheets use the keyword 'mode' for what is called
-a 'function' in the pin-controller subsystem.
-
-Required subnode-properties:
-- groups: a list of strings describing the group names.
-- function: a string describing the function used to mux the groups.
-
-* Reset controller binding
-
-A reset controller is part of the chip control registers set. The chip control
-node also provides the reset. The register set is not at the same offset between
-Berlin SoCs.
-
-Required property:
-- #reset-cells: must be set to 2
-
 Example:
 
 chip: chip-control@ea0000 {
-	compatible = "marvell,berlin2-chip-ctrl";
-	#clock-cells = <1>;
-	#reset-cells = <2>;
+	compatible = "simple-mfd", "syscon";
 	reg = <0xea0000 0x400>;
-	clocks = <&refclk>, <&externaldev 0>;
-	clock-names = "refclk", "video_ext0";
 
-	spi1_pmux: spi1-pmux {
-		groups = "G0";
-		function = "spi1";
-	};
+	/* sub-device nodes */
 };
 
 sysctrl: system-controller@d000 {
-	compatible = "marvell,berlin2-system-ctrl";
+	compatible = "simple-mfd", "syscon";
 	reg = <0xd000 0x100>;
 
-	uart0_pmux: uart0-pmux {
-		groups = "GSM4";
-		function = "uart0";
-	};
-
-	uart1_pmux: uart1-pmux {
-		groups = "GSM5";
-		function = "uart1";
-	};
-
-	uart2_pmux: uart2-pmux {
-		groups = "GSM3";
-		function = "uart2";
-	};
+	/* sub-device nodes */
 };
diff --git a/Documentation/devicetree/bindings/arm/scu.txt b/Documentation/devicetree/bindings/arm/scu.txt
new file mode 100644
index 000000000000..c447680519bb
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/scu.txt
@@ -0,0 +1,25 @@
+* ARM Snoop Control Unit (SCU)
+
+As part of the MPCore complex, Cortex-A5 and Cortex-A9 are provided
+with a Snoop Control Unit. The register range is usually 256 (0x100)
+bytes.
+
+References:
+
+- Cortex-A9: see DDI0407E Cortex-A9 MPCore Technical Reference Manual
+  Revision r2p0
+- Cortex-A5: see DDI0434B Cortex-A5 MPCore Technical Reference Manual
+  Revision r0p1
+
+- compatible : Should be:
+	"arm,cortex-a9-scu"
+	"arm,cortex-a5-scu"
+
+- reg : Specify the base address and the size of the SCU register window.
+
+Example:
+
+scu@a04100000 {
+	compatible = "arm,cortex-a9-scu";
+	reg = <0xa0410000 0x100>;
+};
diff --git a/Documentation/devicetree/bindings/arm/ux500/boards.txt b/Documentation/devicetree/bindings/arm/ux500/boards.txt
new file mode 100644
index 000000000000..b8737a8de718
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/ux500/boards.txt
@@ -0,0 +1,83 @@
+ST-Ericsson Ux500 boards
+------------------------
+
+Required properties (in root node) one of these:
+	compatible = "st-ericsson,mop500" (legacy)
+	compatible = "st-ericsson,u8500"
+
+Required node (under root node):
+
+soc: represents the system-on-chip and contains the chip
+peripherals
+
+Required property of soc node, one of these:
+	compatible = "stericsson,db8500"
+
+Required subnodes under soc node:
+
+backupram: (used for CPU spin tables and for storing data
+during retention, system won't boot without this):
+	compatible = "ste,dbx500-backupram"
+
+scu:
+	see binding for arm/scu.txt
+
+interrupt-controller:
+	see binding for arm/gic.txt
+
+timer:
+	see binding for arm/twd.txt
+
+clocks:
+	see binding for clocks/ux500.txt
+
+Example:
+
+/dts-v1/;
+
+/ {
+        model = "ST-Ericsson HREF (pre-v60) and ST UIB";
+        compatible = "st-ericsson,mop500", "st-ericsson,u8500";
+
+        soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "stericsson,db8500";
+		interrupt-parent = <&intc>;
+		ranges;
+
+		backupram@80150000 {
+			compatible = "ste,dbx500-backupram";
+			reg = <0x80150000 0x2000>;
+		};
+
+		intc: interrupt-controller@a0411000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <1>;
+			interrupt-controller;
+			reg = <0xa0411000 0x1000>,
+			      <0xa0410100 0x100>;
+		};
+
+		scu@a04100000 {
+			compatible = "arm,cortex-a9-scu";
+			reg = <0xa0410000 0x100>;
+		};
+
+		timer@a0410600 {
+			compatible = "arm,cortex-a9-twd-timer";
+			reg = <0xa0410600 0x20>;
+			interrupts = <1 13 0x304>; /* IRQ level high per-CPU */
+			clocks = <&smp_twd_clk>;
+		};
+
+		clocks {
+			compatible = "stericsson,u8500-clks";
+
+			smp_twd_clk: smp-twd-clock {
+				#clock-cells = <0>;
+			};
+		};
+        };
+};
diff --git a/Documentation/devicetree/bindings/clock/hi6220-clock.txt b/Documentation/devicetree/bindings/clock/hi6220-clock.txt
new file mode 100644
index 000000000000..259e30af9597
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/hi6220-clock.txt
@@ -0,0 +1,34 @@
+* Hisilicon Hi6220 Clock Controller
+
+Clock control registers reside in different Hi6220 system controllers,
+please refer the following document to know more about the binding rules
+for these system controllers:
+
+Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
+
+Required Properties:
+
+- compatible: the compatible should be one of the following strings to
+	indicate the clock controller functionality.
+
+	- "hisilicon,hi6220-aoctrl"
+	- "hisilicon,hi6220-sysctrl"
+	- "hisilicon,hi6220-mediactrl"
+	- "hisilicon,hi6220-pmctrl"
+
+- reg: physical base address of the controller and length of memory mapped
+  region.
+
+- #clock-cells: should be 1.
+
+For example:
+	sys_ctrl: sys_ctrl@f7030000 {
+		compatible = "hisilicon,hi6220-sysctrl", "syscon";
+		reg = <0x0 0xf7030000 0x0 0x2000>;
+		#clock-cells = <1>;
+	};
+
+Each clock is assigned an identifier and client nodes use this identifier
+to specify the clock which they consume.
+
+All these identifier could be found in <dt-bindings/clock/hi6220-clock.h>.
diff --git a/Documentation/devicetree/bindings/clock/imx7d-clock.txt b/Documentation/devicetree/bindings/clock/imx7d-clock.txt
new file mode 100644
index 000000000000..9d3026d81a68
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/imx7d-clock.txt
@@ -0,0 +1,13 @@
+* Clock bindings for Freescale i.MX7 Dual
+
+Required properties:
+- compatible: Should be "fsl,imx7d-ccm"
+- reg: Address and length of the register set
+- #clock-cells: Should be <1>
+- clocks: list of clock specifiers, must contain an entry for each required
+  entry in clock-names
+- clock-names: should include entries "ckil", "osc"
+
+The clock consumer should specify the desired clock by having the clock
+ID in its "clocks" phandle cell.  See include/dt-bindings/clock/imx7d-clock.h
+for the full list of i.MX7 Dual clock IDs.
diff --git a/Documentation/devicetree/bindings/clock/marvell,berlin.txt b/Documentation/devicetree/bindings/clock/marvell,berlin.txt
new file mode 100644
index 000000000000..c611c495f3ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/marvell,berlin.txt
@@ -0,0 +1,31 @@
+Device Tree Clock bindings for Marvell Berlin
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Clock related registers are spread among the chip control registers. Berlin
+clock node should be a sub-node of the chip controller node. Marvell Berlin2
+(BG2, BG2CD, BG2Q) SoCs share the same IP for PLLs and clocks, with some
+minor differences in features and register layout.
+
+Required properties:
+- compatible: must be "marvell,berlin2-clk" or "marvell,berlin2q-clk"
+- #clock-cells: must be 1
+- clocks: must be the input parent clock phandle
+- clock-names: name of the input parent clock
+	Allowed clock-names for the reference clocks are
+	"refclk" for the SoCs oscillator input on all SoCs,
+	and SoC-specific input clocks for
+	BG2/BG2CD: "video_ext0" for the external video clock input
+
+
+Example:
+
+chip_clk: clock {
+	compatible = "marvell,berlin2q-clk";
+
+	#clock-cells = <1>;
+	clocks = <&refclk>;
+	clock-names = "refclk";
+};
diff --git a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt
index 3e2c88d97ad4..02f979a48aeb 100644
--- a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt
@@ -58,5 +58,5 @@ Example:
 			interrupt-controller;
 			#address-cells = <0>;
 			#interrupt-cells = <1>;
-		}
+		};
 	};
diff --git a/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt
new file mode 100644
index 000000000000..a8bb5e26019c
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt
@@ -0,0 +1,43 @@
+* Pin-controller driver for the Marvell Berlin SoCs
+
+Pin control registers are part of both chip controller and system
+controller register sets. Pin controller nodes should be a sub-node of
+either the chip controller or system controller node. The pins
+controlled are organized in groups, so no actual pin information is
+needed.
+
+A pin-controller node should contain subnodes representing the pin group
+configurations, one per function. Each subnode has the group name and
+the muxing function used.
+
+Be aware the Marvell Berlin datasheets use the keyword 'mode' for what
+is called a 'function' in the pin-controller subsystem.
+
+Required properties:
+- compatible: should be one of:
+	"marvell,berlin2-soc-pinctrl",
+	"marvell,berlin2-system-pinctrl",
+	"marvell,berlin2cd-soc-pinctrl",
+	"marvell,berlin2cd-system-pinctrl",
+	"marvell,berlin2q-soc-pinctrl",
+	"marvell,berlin2q-system-pinctrl"
+
+Required subnode-properties:
+- groups: a list of strings describing the group names.
+- function: a string describing the function used to mux the groups.
+
+Example:
+
+sys_pinctrl: pin-controller {
+	compatible = "marvell,berlin2q-system-pinctrl";
+
+	uart0_pmux: uart0-pmux {
+		groups = "GSM12";
+		function = "uart0";
+	};
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pmux>;
+	pinctrl-names = "default";
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
new file mode 100644
index 000000000000..8bbf25d58656
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
@@ -0,0 +1,27 @@
+* Freescale i.MX7 Dual IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: "fsl,imx7d-iomuxc"
+- fsl,pins: each entry consists of 6 integers and represents the mux and config
+  setting for one pin.  The first 5 integers <mux_reg conf_reg input_reg mux_val
+  input_val> are specified using a PIN_FUNC_ID macro, which can be found in
+  imx7d-pinfunc.h under device tree source folder.  The last integer CONFIG is
+  the pad setting value like pull-up on this pin.  Please refer to i.MX7 Dual
+  Reference Manual for detailed CONFIG settings.
+
+CONFIG bits definition:
+PAD_CTL_PUS_100K_DOWN           (0 << 5)
+PAD_CTL_PUS_5K_UP               (1 << 5)
+PAD_CTL_PUS_47K_UP              (2 << 5)
+PAD_CTL_PUS_100K_UP             (3 << 5)
+PAD_CTL_PUE                     (1 << 4)
+PAD_CTL_HYS                     (1 << 3)
+PAD_CTL_SRE_SLOW                (1 << 2)
+PAD_CTL_SRE_FAST                (0 << 2)
+PAD_CTL_DSE_X1                  (0 << 0)
+PAD_CTL_DSE_X2                  (1 << 0)
+PAD_CTL_DSE_X3                  (2 << 0)
+PAD_CTL_DSE_X4                  (3 << 0)
diff --git a/Documentation/devicetree/bindings/reset/berlin,reset.txt b/Documentation/devicetree/bindings/reset/berlin,reset.txt
new file mode 100644
index 000000000000..514fee098b4b
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/berlin,reset.txt
@@ -0,0 +1,23 @@
+Marvell Berlin reset controller
+===============================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+The reset controller node must be a sub-node of the chip controller
+node on Berlin SoCs.
+
+Required properties:
+- compatible: should be "marvell,berlin2-reset"
+- #reset-cells: must be set to 2
+
+Example:
+
+chip_rst: reset {
+	compatible = "marvell,berlin2-reset";
+	#reset-cells = <2>;
+};
+
+&usb_phy0 {
+	resets = <&chip_rst 0x104 12>;
+};
diff --git a/Documentation/devicetree/bindings/reset/brcm,bcm63138-pmb.txt b/Documentation/devicetree/bindings/reset/brcm,bcm63138-pmb.txt
new file mode 100644
index 000000000000..a98872d27872
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/brcm,bcm63138-pmb.txt
@@ -0,0 +1,19 @@
+Broadcom BCM63138 Processor Monitor Bus binding
+===============================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Require properties:
+
+- compatible: must be "brcm,bcm63138-pmb"
+- reg: base register address and size for this bus controller
+- #reset-cells: must be 2 first cell is the address within the bus instance designated
+  by the phandle, and the second is the number of zones for this peripheral
+
+Example:
+	pmb0: reset-controller@4800c0 {
+		compatible = "brcm,bcm63138-pmb";
+		reg = <0x4800c0 0x10>;
+		#reset-cells = <2>;
+	};
diff --git a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt
index ab757b84daa7..ac2fcd6ff4b8 100644
--- a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt
+++ b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt
@@ -6,7 +6,8 @@ Required properties:
     * "samsung,s3c2416-rtc" - for controllers compatible with s3c2416 rtc.
     * "samsung,s3c2443-rtc" - for controllers compatible with s3c2443 rtc.
     * "samsung,s3c6410-rtc" - for controllers compatible with s3c6410 rtc.
-    * "samsung,exynos3250-rtc" - for controllers compatible with exynos3250 rtc.
+    * "samsung,exynos3250-rtc" - (deprecated) for controllers compatible with
+                                 exynos3250 rtc (use "samsung,s3c6410-rtc").
 - reg: physical base address of the controller and length of memory mapped
   region.
 - interrupts: Two interrupt numbers to the cpu should be specified. First
diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt
index 4c388bb2f0a2..8f771441be60 100644
--- a/Documentation/devicetree/bindings/spi/sh-msiof.txt
+++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt
@@ -60,7 +60,7 @@ Example:
 
 	msiof0: spi@e6e20000 {
 		compatible = "renesas,msiof-r8a7791";
-		reg = <0 0xe6e20000 0 0x0064>, <0 0xe7e20000 0 0x0064>;
+		reg = <0 0xe6e20000 0 0x0064>;
 		interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>;
 		dmas = <&dmac0 0x51>, <&dmac0 0x52>;
diff --git a/Documentation/devicetree/bindings/timer/cadence,ttc-timer.txt b/Documentation/devicetree/bindings/timer/cadence,ttc-timer.txt
index 993695c659e1..eeee6cd51e5c 100644
--- a/Documentation/devicetree/bindings/timer/cadence,ttc-timer.txt
+++ b/Documentation/devicetree/bindings/timer/cadence,ttc-timer.txt
@@ -6,6 +6,9 @@ Required properties:
 - interrupts : A list of 3 interrupts; one per timer channel.
 - clocks: phandle to the source clock
 
+Optional properties:
+- timer-width: Bit width of the timer, necessary if not 16.
+
 Example:
 
 ttc0: ttc0@f8001000 {
@@ -14,4 +17,5 @@ ttc0: ttc0@f8001000 {
 	compatible = "cdns,ttc";
 	reg = <0xF8001000 0x1000>;
 	clocks = <&cpu_clk 3>;
+	timer-width = <32>;
 };
diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt
index e180d56c75db..1be8d7a26c15 100644
--- a/Documentation/devicetree/bindings/usb/atmel-usb.txt
+++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt
@@ -5,6 +5,13 @@ OHCI
 Required properties:
  - compatible: Should be "atmel,at91rm9200-ohci" for USB controllers
    used in host mode.
+ - reg: Address and length of the register set for the device
+ - interrupts: Should contain ehci interrupt
+ - clocks: Should reference the peripheral, host and system clocks
+ - clock-names: Should contains two strings
+		"ohci_clk" for the peripheral clock
+		"hclk" for the host clock
+		"uhpck" for the system clock
  - num-ports: Number of ports.
  - atmel,vbus-gpio: If present, specifies a gpio that needs to be
    activated for the bus to be powered.
@@ -14,6 +21,8 @@ Required properties:
 usb0: ohci@00500000 {
 	compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 	reg = <0x00500000 0x100000>;
+	clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+	clock-names = "ohci_clk", "hclk", "uhpck";
 	interrupts = <20 4>;
 	num-ports = <2>;
 };
@@ -23,11 +32,19 @@ EHCI
 Required properties:
  - compatible: Should be "atmel,at91sam9g45-ehci" for USB controllers
    used in host mode.
+ - reg: Address and length of the register set for the device
+ - interrupts: Should contain ehci interrupt
+ - clocks: Should reference the peripheral and the UTMI clocks
+ - clock-names: Should contains two strings
+		"ehci_clk" for the peripheral clock
+		"usb_clk" for the UTMI clock
 
 usb1: ehci@00800000 {
 	compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
 	reg = <0x00800000 0x100000>;
 	interrupts = <22 4>;
+	clocks = <&utmi>, <&uhphs_clk>;
+	clock-names = "usb_clk", "ehci_clk";
 };
 
 AT91 USB device controller
@@ -53,6 +70,8 @@ usb1: gadget@fffa4000 {
 	compatible = "atmel,at91rm9200-udc";
 	reg = <0xfffa4000 0x4000>;
 	interrupts = <10 4>;
+	clocks = <&udc_clk>, <&udpck>;
+	clock-names = "pclk", "hclk";
 	atmel,vbus-gpio = <&pioC 5 0>;
 };
 
@@ -65,6 +84,10 @@ Required properties:
 	       "sama5d3-udc"
  - reg: Address and length of the register set for the device
  - interrupts: Should contain usba interrupt
+ - clocks: Should reference the peripheral and host clocks
+ - clock-names: Should contains two strings
+		"pclk" for the peripheral clock
+		"hclk" for the host clock
  - ep childnode: To specify the number of endpoints and their properties.
 
 Optional properties:
@@ -86,6 +109,8 @@ usb2: gadget@fff78000 {
 	reg = <0x00600000 0x80000
 	       0xfff78000 0x400>;
 	interrupts = <27 4 0>;
+	clocks = <&utmi>, <&udphs_clk>;
+	clock-names = "hclk", "pclk";
 	atmel,vbus-gpio = <&pioB 19 0>;
 
 	ep0 {
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index a37ad9939a8a..58d69302ddfb 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -40,6 +40,7 @@ calxeda	Calxeda
 capella	Capella Microsystems, Inc
 cavium	Cavium, Inc.
 cdns	Cadence Design Systems Inc.
+ceva	Ceva, Inc.
 chipidea	Chipidea, Inc
 chipone		ChipOne
 chipspark	ChipSPARK
@@ -52,6 +53,7 @@ cnxt	Conexant Systems, Inc.
 cortina	Cortina Systems, Inc.
 cosmic	Cosmic Circuits
 crystalfontz	Crystalfontz America, Inc.
+cubietech	Cubietech, Ltd.
 dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
 davicom	DAVICOM Semiconductor, Inc.
 delta	Delta Electronics, Inc.
@@ -61,6 +63,7 @@ digilent	Diglent, Inc.
 dlg	Dialog Semiconductor
 dlink	D-Link Corporation
 dmo	Data Modul AG
+ea	Embedded Artists AB
 ebv	EBV Elektronik
 edt	Emerging Display Technologies
 elan	Elan Microelectronic Corp.
@@ -91,9 +94,11 @@ gumstix	Gumstix, Inc.
 gw	Gateworks Corporation
 hannstar	HannStar Display Corporation
 haoyu	Haoyu Microelectronic Co. Ltd.
+hardkernel	Hardkernel Co., Ltd
 himax	Himax Technologies, Inc.
 hisilicon	Hisilicon Limited.
 hit	Hitachi Ltd.
+hitex	Hitex Development Tools
 honeywell	Honeywell
 hp	Hewlett Packard
 i2se	I2SE GmbH
@@ -160,6 +165,7 @@ radxa	Radxa
 raidsonic	RaidSonic Technology GmbH
 ralink	Mediatek/Ralink Technology Corp.
 ramtron	Ramtron International
+raspberrypi	Raspberry Pi Foundation
 realtek Realtek Semiconductor Corp.
 renesas	Renesas Electronics Corporation
 richtek	Richtek Technology Corporation
@@ -192,6 +198,7 @@ ste	ST-Ericsson
 stericsson	ST-Ericsson
 synology	Synology, Inc.
 tbs	TBS Technologies
+tcl	Toby Churchill Ltd.
 thine	THine Electronics, Inc.
 ti	Texas Instruments
 tlm	Trusted Logic Mobility
@@ -205,6 +212,7 @@ variscite	Variscite Ltd.
 via	VIA Technologies, Inc.
 virtio	Virtual I/O Device Specification, developed by the OASIS consortium
 voipac	Voipac Technologies s.r.o.
+wexler	Wexler
 winbond Winbond Electronics corp.
 wlf	Wolfson Microelectronics
 wm	Wondermedia Technologies, Inc.