#
# SPI driver configuration
#
# NOTE: the reason this doesn't show SPI slave support is mostly that
# nobody's needed a slave side API yet. The master-role API is not
# fully appropriate there, so it'd need some thought to do well.
#
menuconfig SPI
bool "SPI support"
depends on HAS_IOMEM
help
The "Serial Peripheral Interface" is a low level synchronous
protocol. Chips that support SPI can have data transfer rates
up to several tens of Mbit/sec. Chips are addressed with a
controller and a chipselect. Most SPI slaves don't support
dynamic device discovery; some are even write-only or read-only.
SPI is widely used by microcontrollers to talk with sensors,
eeprom and flash memory, codecs and various other controller
chips, analog to digital (and d-to-a) converters, and more.
MMC and SD cards can be accessed using SPI protocol; and for
DataFlash cards used in MMC sockets, SPI must always be used.
SPI is one of a family of similar protocols using a four wire
interface (select, clock, data in, data out) including Microwire
(half duplex), SSP, SSI, and PSP. This driver framework should
work with most such devices and controllers.
if SPI
config SPI_DEBUG
boolean "Debug support for SPI drivers"
depends on DEBUG_KERNEL
help
Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
sysfs, and debugfs support in SPI controller and protocol drivers.
#
# MASTER side ... talking to discrete SPI slave chips including microcontrollers
#
config SPI_MASTER
# boolean "SPI Master Support"
boolean
default SPI
help
If your system has an master-capable SPI controller (which
provides the clock and chipselect), you can enable that
controller and the protocol drivers for the SPI slave chips
that are connected.
if SPI_MASTER
comment "SPI Master Controller Drivers"
config SPI_ATMEL
tristate "Atmel SPI Controller"
depends on (ARCH_AT91 || AVR32)
help
This selects a driver for the Atmel SPI Controller, present on
many AT32 (AVR32) and AT91 (ARM) chips.
config SPI_BFIN
tristate "SPI controller driver for ADI Blackfin5xx"
depends on BLACKFIN
help
This is the SPI controller master driver for Blackfin 5xx processor.
config SPI_AU1550
tristate "Au1550/Au12x0 SPI Controller"
depends on (SOC_AU1550 || SOC_AU1200) && EXPERIMENTAL
select SPI_BITBANG
help
If you say yes to this option, support will be included for the
Au1550 SPI controller (may also work with Au1200,Au1210,Au1250).
This driver can also be built as a module. If so, the module
will be called au1550_spi.
config SPI_BITBANG
tristate "Utilities for Bitbanging SPI masters"
help
With a few GPIO pins, your system can bitbang the SPI protocol.
Select this to get SPI support through I/O pins (GPIO, parallel
port, etc). Or, some systems' SPI master controller drivers use
this code to manage the per-word or per-transfer accesses to the
hardware shift registers.
This is library code, and is automatically selected by drivers that
need it. You only need to select this explicitly to support driver
modules that aren't part of this kernel tree.
config SPI_BUTTERFLY
tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
depends on PARPORT
select SPI_BITBANG
help
This uses a custom parallel port cable to connect to an AVR
Butterfly <http://www.atmel.com/products/avr/butterfly>, an
inexpensive battery powered microcontroller evaluation board.
This same cable can be used to flash new firmware.
config SPI_COLDFIRE_QSPI
tristate "Freescale Coldfire QSPI controller"
depends on (M520x || M523x || M5249 || M527x || M528x || M532x)
help
This enables support for the Coldfire QSPI controller in master
mode.
This driver can also be built as a module. If so, the module
will be called coldfire_qspi.
config SPI_DAVINCI
tristate "SPI controller driver for DaVinci/DA8xx SoC's"
depends on SPI_MASTER && ARCH_DAVINCI
select SPI_BITBANG
help
SPI master controller for DaVinci and DA8xx SPI modules.
config SPI_EP93XX
tristate "Cirrus Logic EP93xx SPI controller"
depends on ARCH_EP93XX
help
This enables using the Cirrus EP93xx SPI controller in master
mode.
To compile this driver as a module, choose M here. The module will be
called ep93xx_spi.
config SPI_GPIO
tristate "GPIO-based bitbanging SPI Master"
depends on GENERIC_GPIO
select SPI_BITBANG
help
This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
interface to manage MOSI, MISO, SCK, and chipselect signals. SPI
slaves connected to a bus using this driver are configured as usual,
except that the spi_board_info.controller_data holds the GPIO number
for the chipselect used by this controller driver.
Note that this driver often won't achieve even 1 Mbit/sec speeds,
making it unusually slow for SPI. If your platform can inline
GPIO operations, you should be able to leverage that for better
speed with a custom version of this driver; see the source code.
config SPI_IMX_VER_IMX1
def_bool y if SOC_IMX1
config SPI_IMX_VER_0_0
def_bool y if SOC_IMX21 || SOC_IMX27
config SPI_IMX_VER_0_4
def_bool y if ARCH_MX31
config SPI_IMX_VER_0_7
def_bool y if ARCH_MX25 || ARCH_MX35 || ARCH_MX51
config SPI_IMX_VER_2_3
def_bool y if ARCH_MX51
config SPI_IMX
tristate "Freescale i.MX SPI controllers"
depends on ARCH_MXC
select SPI_BITBANG
default m if IMX_HAVE_PLATFORM_SPI_IMX
help
This enables using the Freescale i.MX SPI controllers in master
mode.
config SPI_LM70_LLP
tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
depends on PARPORT && EXPERIMENTAL
select SPI_BITBANG
help
This driver supports the NS LM70 LLP Evaluation Board,
which interfaces to an LM70 temperature sensor using
a parallel port.
config SPI_MPC52xx
tristate "Freescale MPC52xx SPI (non-PSC) controller support"
depends on PPC_MPC52xx && SPI
select SPI_MASTER_OF
help
This drivers supports the MPC52xx SPI controller in master SPI
mode.
config SPI_MPC52xx_PSC
tristate "Freescale MPC52xx PSC SPI controller"
depends on PPC_MPC52xx && EXPERIMENTAL
help
This enables using the Freescale MPC52xx Programmable Serial
Controller in master SPI mode.
config SPI_MPC512x_PSC
tristate "Freescale MPC512x PSC SPI controller"
depends on SPI_MASTER && PPC_MPC512x
help
This enables using the Freescale MPC5121 Programmable Serial
Controller in SPI master mode.
config SPI_FSL_LIB
tristate
depends on FSL_SOC
config SPI_FSL_SPI
tristate "Freescale SPI controller"
depends on FSL_SOC
select SPI_FSL_LIB
help
This enables using the Freescale SPI controllers in master mode.
MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
config SPI_FSL_ESPI
tristate "Freescale eSPI controller"
depends on FSL_SOC
select SPI_FSL_LIB
help
This enables using the Freescale eSPI controllers in master mode.
From MPC8536, 85xx platform uses the controller, and all P10xx,
P20xx, P30xx,P40xx, P50xx uses this controller.
config SPI_OMAP_UWIRE
tristate "OMAP1 MicroWire"
depends on ARCH_OMAP1
select SPI_BITBANG
help
This hooks up to the MicroWire controller on OMAP1 chips.
config SPI_OMAP24XX
tristate "McSPI driver for OMAP"
depends on ARCH_OMAP2PLUS
help
SPI master controller for OMAP24XX and later Multichannel SPI
(McSPI) modules.
config SPI_OMAP_100K
tristate "OMAP SPI 100K"
depends on SPI_MASTER && (ARCH_OMAP850 || ARCH_OMAP730)
help
OMAP SPI 100K master controller for omap7xx boards.
config SPI_ORION
tristate "Orion SPI master (EXPERIMENTAL)"
depends on PLAT_ORION && EXPERIMENTAL
help
This enables using the SPI master controller on the Orion chips.
config SPI_PL022
tristate "ARM AMBA PL022 SSP controller (EXPERIMENTAL)"
depends on ARM_AMBA && EXPERIMENTAL
default y if MACH_U300
default y if ARCH_REALVIEW
default y if INTEGRATOR_IMPD1
default y if ARCH_VERSATILE
help
This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
controller. If you have an embedded system with an AMBA(R)
bus and a PL022 controller, say Y or M here.
config SPI_PPC4xx
tristate "PPC4xx SPI Controller"
depends on PPC32 && 4xx && SPI_MASTER
select SPI_BITBANG
help
This selects a driver for the PPC4xx SPI Controller.
config SPI_PXA2XX
tristate "PXA2xx SSP SPI master"
depends on ARCH_PXA && EXPERIMENTAL
select PXA_SSP
help
This enables using a PXA2xx SSP port as a SPI master controller.
The driver can be configured to use any SSP port and additional
documentation can be found a Documentation/spi/pxa2xx.
config SPI_S3C24XX
tristate "Samsung S3C24XX series SPI"
depends on ARCH_S3C2410 && EXPERIMENTAL
select SPI_BITBANG
help
SPI driver for Samsung S3C24XX series ARM SoCs
config SPI_S3C24XX_FIQ
bool "S3C24XX driver with FIQ pseudo-DMA"
depends on SPI_S3C24XX
select FIQ
help
Enable FIQ support for the S3C24XX SPI driver to provide pseudo
DMA by using the fast-interrupt request framework, This allows
the driver to get DMA-like performance when there are either
no free DMA channels, or when doing transfers that required both
TX and RX data paths.
config SPI_S3C24XX_GPIO
tristate "Samsung S3C24XX series SPI by GPIO"
depends on ARCH_S3C2410 && EXPERIMENTAL
select SPI_BITBANG
help
SPI driver for Samsung S3C24XX series ARM SoCs using
GPIO lines to provide the SPI bus. This can be used where
the inbuilt hardware cannot provide the transfer mode, or
where the board is using non hardware connected pins.
config SPI_S3C64XX
tristate "Samsung S3C64XX series type SPI"
depends on ARCH_S3C64XX && EXPERIMENTAL
select S3C64XX_DMA
help
SPI driver for Samsung S3C64XX and newer SoCs.
config SPI_SH_MSIOF
tristate "SuperH MSIOF SPI controller"
depends on SUPERH && HAVE_CLK
select SPI_BITBANG
help
SPI driver for SuperH MSIOF blocks.
config SPI_SH_SCI
tristate "SuperH SCI SPI controller"
depends on SUPERH
select SPI_BITBANG
help
SPI driver for SuperH SCI blocks.
config SPI_STMP3XXX
tristate "Freescale STMP37xx/378x SPI/SSP controller"
depends on ARCH_STMP3XXX && SPI_MASTER
help
SPI driver for Freescale STMP37xx/378x SoC SSP interface
config SPI_TEGRA
tristate "Nvidia Tegra SPI controller"
depends on ARCH_TEGRA
select TEGRA_SYSTEM_DMA
help
SPI driver for NVidia Tegra SoCs
config SPI_TOPCLIFF_PCH
tristate "Topcliff PCH SPI Controller"
depends on PCI
help
SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
used in some x86 embedded processors.
config SPI_TXX9
tristate "Toshiba TXx9 SPI controller"
depends on GENERIC_GPIO && CPU_TX49XX
help
SPI driver for Toshiba TXx9 MIPS SoCs
config SPI_XILINX
tristate "Xilinx SPI controller common module"
depends on HAS_IOMEM && EXPERIMENTAL
select SPI_BITBANG
help
This exposes the SPI controller IP from the Xilinx EDK.
See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
Product Specification document (DS464) for hardware details.
Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
config SPI_NUC900
tristate "Nuvoton NUC900 series SPI"
depends on ARCH_W90X900 && EXPERIMENTAL
select SPI_BITBANG
help
SPI driver for Nuvoton NUC900 series ARM SoCs
#
# Add new SPI master controllers in alphabetical order above this line
#
config SPI_DESIGNWARE
tristate "DesignWare SPI controller core support"
depends on SPI_MASTER
help
general driver for SPI controller core from DesignWare
config SPI_DW_PCI
tristate "PCI interface driver for DW SPI core"
depends on SPI_DESIGNWARE && PCI
config SPI_DW_MMIO
tristate "Memory-mapped io interface driver for DW SPI core"
depends on SPI_DESIGNWARE && HAVE_CLK
#
# There are lots of SPI device types, with sensors and memory
# being probably the most widely used ones.
#
comment "SPI Protocol Masters"
config SPI_SPIDEV
tristate "User mode SPI device driver support"
depends on EXPERIMENTAL
help
This supports user mode SPI protocol drivers.
Note that this application programming interface is EXPERIMENTAL
and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
config SPI_TLE62X0
tristate "Infineon TLE62X0 (for power switching)"
depends on SYSFS
help
SPI driver for Infineon TLE62X0 series line driver chips,
such as the TLE6220, TLE6230 and TLE6240. This provides a
sysfs interface, with each line presented as a kind of GPIO
exposing both switch control and diagnostic feedback.
#
# Add new SPI protocol masters in alphabetical order above this line
#
endif # SPI_MASTER
# (slave support would go here)
endif # SPI
