/*
* Definitions for the new Marvell Yukon / SysKonenct driver.
*/
#ifndef _SKGE_H
#define _SKGE_H
/* PCI config registers */
#define PCI_DEV_REG1 0x40
#define PCI_PHY_COMA 0x8000000
#define PCI_VIO 0x2000000
#define PCI_DEV_REG2 0x44
#define PCI_REV_DESC 0x4
#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
PCI_STATUS_SIG_SYSTEM_ERROR | \
PCI_STATUS_REC_MASTER_ABORT | \
PCI_STATUS_REC_TARGET_ABORT | \
PCI_STATUS_PARITY)
enum csr_regs {
B0_RAP = 0x0000,
B0_CTST = 0x0004,
B0_LED = 0x0006,
B0_POWER_CTRL = 0x0007,
B0_ISRC = 0x0008,
B0_IMSK = 0x000c,
B0_HWE_ISRC = 0x0010,
B0_HWE_IMSK = 0x0014,
B0_SP_ISRC = 0x0018,
B0_XM1_IMSK = 0x0020,
B0_XM1_ISRC = 0x0028,
B0_XM1_PHY_ADDR = 0x0030,
B0_XM1_PHY_DATA = 0x0034,
B0_XM2_IMSK = 0x0040,
B0_XM2_ISRC = 0x0048,
B0_XM2_PHY_ADDR = 0x0050,
B0_XM2_PHY_DATA = 0x0054,
B0_R1_CSR = 0x0060,
B0_R2_CSR = 0x0064,
B0_XS1_CSR = 0x0068,
B0_XA1_CSR = 0x006c,
B0_XS2_CSR = 0x0070,
B0_XA2_CSR = 0x0074,
B2_MAC_1 = 0x0100,
B2_MAC_2 = 0x0108,
B2_MAC_3 = 0x0110,
B2_CONN_TYP = 0x0118,
B2_PMD_TYP = 0x0119,
B2_MAC_CFG = 0x011a,
B2_CHIP_ID = 0x011b,
B2_E_0 = 0x011c,
B2_E_1 = 0x011d,
B2_E_2 = 0x011e,
B2_E_3 = 0x011f,
B2_FAR = 0x0120,
B2_FDP = 0x0124,
B2_LD_CTRL = 0x0128,
B2_LD_TEST = 0x0129,
B2_TI_INI = 0x0130,
B2_TI_VAL = 0x0134,
B2_TI_CTRL = 0x0138,
B2_TI_TEST = 0x0139,
B2_IRQM_INI = 0x0140,
B2_IRQM_VAL = 0x0144,
B2_IRQM_CTRL = 0x0148,
B2_IRQM_TEST = 0x0149,
B2_IRQM_MSK = 0x014c,
B2_IRQM_HWE_MSK = 0x0150,
B2_TST_CTRL1 = 0x0158,
B2_TST_CTRL2 = 0x0159,
B2_GP_IO = 0x015c,
B2_I2C_CTRL = 0x0160,
B2_I2C_DATA = 0x0164,
B2_I2C_IRQ = 0x0168,
B2_I2C_SW = 0x016c,
B2_BSC_INI = 0x0170,
B2_BSC_VAL = 0x0174,
B2_BSC_CTRL = 0x0178,
B2_BSC_STAT = 0x0179,
B2_BSC_TST = 0x017a,
B3_RAM_ADDR = 0x0180,
B3_RAM_DATA_LO = 0x0184,
B3_RAM_DATA_HI = 0x0188,
B3_RI_WTO_R1 = 0x0190,
B3_RI_WTO_XA1 = 0x0191,
B3_RI_WTO_XS1 = 0x0192,
B3_RI_RTO_R1 = 0x0193,
B3_RI_RTO_XA1 = 0x0194,
B3_RI_RTO_XS1 = 0x0195,
B3_RI_WTO_R2 = 0x0196,
B3_RI_WTO_XA2 = 0x0197,
B3_RI_WTO_XS2 = 0x0198,
B3_RI_RTO_R2 = 0x0199,
B3_RI_RTO_XA2 = 0x019a,
B3_RI_RTO_XS2 = 0x019b,
B3_RI_TO_VAL = 0x019c,
B3_RI_CTRL = 0x01a0,
B3_RI_TEST = 0x01a2,
B3_MA_TOINI_RX1 = 0x01b0,
B3_MA_TOINI_RX2 = 0x01b1,
B3_MA_TOINI_TX1 = 0x01b2,
B3_MA_TOINI_TX2 = 0x01b3,
B3_MA_TOVAL_RX1 = 0x01b4,
B3_MA_TOVAL_RX2 = 0x01b5,
B3_MA_TOVAL_TX1 = 0x01b6,
B3_MA_TOVAL_TX2 = 0x01b7,
B3_MA_TO_CTRL = 0x01b8,
B3_MA_TO_TEST = 0x01ba,
B3_MA_RCINI_RX1 = 0x01c0,
B3_MA_RCINI_RX2 = 0x01c1,
B3_MA_RCINI_TX1 = 0x01c2,
B3_MA_RCINI_TX2 = 0x01c3,
B3_MA_RCVAL_RX1 = 0x01c4,
B3_MA_RCVAL_RX2 = 0x01c5,
B3_MA_RCVAL_TX1 = 0x01c6,
B3_MA_RCVAL_TX2 = 0x01c7,
B3_MA_RC_CTRL = 0x01c8,
B3_MA_RC_TEST = 0x01ca,
B3_PA_TOINI_RX1 = 0x01d0,
B3_PA_TOINI_RX2 = 0x01d4,
B3_PA_TOINI_TX1 = 0x01d8,
B3_PA_TOINI_TX2 = 0x01dc,
B3_PA_TOVAL_RX1 = 0x01e0,
B3_PA_TOVAL_RX2 = 0x01e4,
B3_PA_TOVAL_TX1 = 0x01e8,
B3_PA_TOVAL_TX2 = 0x01ec,
B3_PA_CTRL = 0x01f0,
B3_PA_TEST = 0x01f2,
};
/* B0_CTST 16 bit Control/Status register */
enum {
CS_CLK_RUN_HOT = 1<<13,/* CLK_RUN hot m. (YUKON-Lite only) */
CS_CLK_RUN_RST = 1<<12,/* CLK_RUN reset (YUKON-Lite only) */
CS_CLK_RUN_ENA = 1<<11,/* CLK_RUN enable (YUKON-Lite only) */
CS_VAUX_AVAIL = 1<<10,/* VAUX available (YUKON only) */
CS_BUS_CLOCK = 1<<9, /* Bus Clock 0/1 = 33/66 MHz */
CS_BUS_SLOT_SZ = 1<<8, /* Slot Size 0/1 = 32/64 bit slot */
CS_ST_SW_IRQ = 1<<7, /* Set IRQ SW Request */
CS_CL_SW_IRQ = 1<<6, /* Clear IRQ SW Request */
CS_STOP_DONE = 1<<5, /* Stop Master is finished */
CS_STOP_MAST = 1<<4, /* Command Bit to stop the master */
CS_MRST_CLR = 1<<3, /* Clear Master reset */
CS_MRST_SET = 1<<2, /* Set Master reset */
CS_RST_CLR = 1<<1, /* Clear Software reset */
CS_RST_SET = 1, /* Set Software reset */
/* B0_LED 8 Bit LED register */
/* Bit 7.. 2: reserved */
LED_STAT_ON = 1<<1, /* Status LED on */
LED_STAT_OFF = 1, /* Status LED off */
/* B0_POWER_CTRL 8 Bit Power Control reg (YUKON only) */
PC_VAUX_ENA = 1<<7, /* Switch VAUX Enable */
PC_VAUX_DIS = 1<<6, /* Switch VAUX Disable */
PC_VCC_ENA = 1<<5, /* Switch VCC Enable */
PC_VCC_DIS = 1<<4, /* Switch VCC Disable */
PC_VAUX_ON = 1<<3, /* Switch VAUX On */
PC_VAUX_OFF = 1<<2, /* Switch VAUX Off */
PC_VCC_ON = 1<<1, /* Switch VCC On */
PC_VCC_OFF = 1<<0, /* Switch VCC Off */
};
/* B2_IRQM_MSK 32 bit IRQ Moderation Mask */
enum {
IS_ALL_MSK = 0xbffffffful, /* All Interrupt bits */
IS_HW_ERR = 1<<31, /* Interrupt HW Error */
/* Bit 30: reserved */
IS_PA_TO_RX1 = 1<<29, /* Packet Arb Timeout Rx1 */
IS_PA_TO_RX2 = 1<<28, /* Packet Arb Timeout Rx2 */
IS_PA_TO_TX1 = 1<<27, /* Packet Arb Timeout Tx1 */
IS_PA_TO_TX2 = 1<<26, /* Packet Arb Timeout Tx2 */
IS_I2C_READY = 1<<25, /* IRQ on end of I2C Tx */
IS_IRQ_SW = 1<<24, /* SW forced IRQ */
IS_EXT_REG = 1<<23, /* IRQ from LM80 or PHY (GENESIS only) */
/* IRQ from PHY (YUKON only) */
IS_TIMINT = 1<<22, /* IRQ from Timer */
IS_MAC1 = 1<<21, /* IRQ from MAC 1 */
IS_LNK_SYNC_M1 = 1<<20, /* Link Sync Cnt wrap MAC 1 */
IS_MAC2 = 1<<19, /* IRQ from MAC 2 */
IS_LNK_SYNC_M2 = 1<<18, /* Link Sync Cnt wrap MAC 2 */
/* Receive Queue 1 */
IS_R1_B = 1<<17, /* Q_R1 End of Buffer */
IS_R1_F = 1<<16, /* Q_R1 End of Frame */
IS_R1_C = 1<<15, /* Q_R1 Encoding Error */
/* Receive Queue 2 */
IS_R2_B = 1<<14, /* Q_R2 End of Buffer */
IS_R2_F = 1<<13, /* Q_R2 End of Frame */
IS_R2_C = 1<<12, /* Q_R2 Encoding Error */
/* Synchronous Transmit Queue 1 */
IS_XS1_B = 1<<11, /* Q_XS1 End of Buffer */
IS_XS1_F = 1<<10, /* Q_XS1 End of Frame */
IS_XS1_C = 1<<9, /* Q_XS1 Encoding Error */
/* Asynchronous Transmit Queue 1 */
IS_XA1_B = 1<<8, /* Q_XA1 End of Buffer */
IS_XA1_F = 1<<7, /* Q_XA1 End of Frame */
IS_XA1_C = 1<<6, /* Q_XA1 Encoding Error */
/* Synchronous Transmit Queue 2 */
IS_XS2_B = 1<<5, /* Q_XS2 End of Buffer */
IS_XS2_F = 1<<4, /* Q_XS2 End of Frame */
IS_XS2_C = 1<<3, /* Q_XS2 Encoding Error */
/* Asynchronous Transmit Queue 2 */
IS_XA2_B = 1<<2, /* Q_XA2 End of Buffer */
IS_XA2_F = 1<<1, /* Q_XA2 End of Frame */
IS_XA2_C = 1<<0, /* Q_XA2 Encoding Error */
IS_TO_PORT1 = IS_PA_TO_RX1 | IS_PA_TO_TX1,
IS_TO_PORT2 = IS_PA_TO_RX2 | IS_PA_TO_TX2,
IS_PORT_1 = IS_XA1_F| IS_R1_F | IS_TO_PORT1 | IS_MAC1,
IS_PORT_2 = IS_XA2_F| IS_R2_F | IS_TO_PORT2 | IS_MAC2,
};
/* B2_IRQM_HWE_MSK 32 bit IRQ Moderation HW Error Mask */
enum {
IS_IRQ_TIST_OV = 1<<13, /* Time Stamp Timer Overflow (YUKON only) */
IS_IRQ_SENSOR = 1<<12, /* IRQ from Sensor (YUKON only) */
IS_IRQ_MST_ERR = 1<<11, /* IRQ master error detected */
IS_IRQ_STAT = 1<<10, /* IRQ status exception */
IS_NO_STAT_M1 = 1<<9, /* No Rx Status from MAC 1 */
IS_NO_STAT_M2 = 1<<8, /* No Rx Status from MAC 2 */
IS_NO_TIST_M1 = 1<<7, /* No Time Stamp from MAC 1 */
IS_NO_TIST_M2 = 1<<6, /* No Time Stamp from MAC 2 */
IS_RAM_RD_PAR = 1<<5, /* RAM Read Parity Error */
IS_RAM_WR_PAR = 1<<4, /* RAM Write Parity Error */
IS_M1_PAR_ERR = 1<<3, /* MAC 1 Parity Error */
IS_M2_PAR_ERR = 1<<2, /* MAC 2 Parity Error */
IS_R1_PAR_ERR = 1<<1, /* Queue R1 Parity Error */
IS_R2_PAR_ERR = 1<<0, /* Queue R2 Parity Error */
IS_ERR_MSK = IS_IRQ_MST_ERR | IS_IRQ_STAT
| IS_NO_STAT_M1 | IS_NO_STAT_M2
| IS_RAM_RD_PAR | IS_RAM_WR_PAR
| IS_M1_PAR_ERR | IS_M2_PAR_ERR
| IS_R1_PAR_ERR | IS_R2_PAR_ERR,
};
/* B2_TST_CTRL1 8 bit Test Control Register 1 */
enum {
TST_FRC_DPERR_MR = 1<<7, /* force DATAPERR on MST RD */
TST_FRC_DPERR_MW = 1<<6, /* force DATAPERR on MST WR */
TST_FRC_DPERR_TR = 1<<5, /* force DATAPERR on TRG RD */
TST_FRC_DPERR_TW = 1<<4, /* force DATAPERR on TRG WR */
TST_FRC_APERR_M = 1<<3, /* force ADDRPERR on MST */
TST_FRC_APERR_T = 1<<2, /* force ADDRPERR on TRG */
TST_CFG_WRITE_ON = 1<<1, /* Enable Config Reg WR */
TST_CFG_WRITE_OFF= 1<<0, /* Disable Config Reg WR */
};
/* B2_MAC_CFG 8 bit MAC Configuration / Chip Revision */
enum {
CFG_CHIP_R_MSK = 0xf<<4, /* Bit 7.. 4: Chip Revision */
/* Bit 3.. 2: reserved */
CFG_DIS_M2_CLK = 1<<1, /* Disable Clock for 2nd MAC */
CFG_SNG_MAC = 1<<0, /* MAC Config: 0=2 MACs / 1=1 MAC*/
};
/* B2_CHIP_ID 8 bit Chip Identification Number */
enum {
CHIP_ID_GENESIS = 0x0a, /* Chip ID for GENESIS */
CHIP_ID_YUKON = 0xb0, /* Chip ID for YUKON */
CHIP_ID_YUKON_LITE = 0xb1, /* Chip ID for YUKON-Lite (Rev. A1-A3) */
CHIP_ID_YUKON_LP = 0xb2, /* Chip ID for YUKON-LP */
CHIP_ID_YUKON_XL = 0xb3, /* Chip ID for YUKON-2 XL */
CHIP_ID_YUKON_EC = 0xb6, /* Chip ID for YUKON-2 EC */
CHIP_ID_YUKON_FE = 0xb7, /* Chip ID for YUKON-2 FE */
CHIP_REV_YU_LITE_A1 = 3, /* Chip Rev. for YUKON-Lite A1,A2 */
CHIP_REV_YU_LITE_A3 = 7, /* Chip Rev. for YUKON-Lite A3 */
};
/* B2_TI_CTRL 8 bit Timer control */
/* B2_IRQM_CTRL 8 bit IRQ Moderation Timer Control */
enum {
TIM_START = 1<<2, /* Start Timer */
TIM_STOP = 1<<1, /* Stop Timer */
TIM_CLR_IRQ = 1<<0, /* Clear Timer IRQ (!IRQM) */
};
/* B2_TI_TEST 8 Bit Timer Test */
/* B2_IRQM_TEST 8 bit IRQ Moderation Timer Test */
/* B28_DPT_TST 8 bit Descriptor Poll Timer Test Reg */
enum {
TIM_T_ON = 1<<2, /* Test mode on */
TIM_T_OFF = 1<<1, /* Test mode off */
TIM_T_STEP = 1<<0, /* Test step */
};
/* B2_GP_IO 32 bit General Purpose I/O Register */
enum {
GP_DIR_9 = 1<<25, /* IO_9 direct, 0=In/1=Out */
GP_DIR_8 = 1<<24, /* IO_8 direct, 0=In/1=Out */
GP_DIR_7 = 1<<23, /* IO_7 direct, 0=In/1=Out */
GP_DIR_6 = 1<<22, /* IO_6 direct, 0=In/1=Out */
GP_DIR_5 = 1<<21, /* IO_5 direct, 0=In/1=Out */
GP_DIR_4 = 1<<20, /* IO_4 direct, 0=In/1=Out */
GP_DIR_3 = 1<<19, /* IO_3 direct, 0=In/1=Out */
GP_DIR_2 = 1<<18, /* IO_2 direct, 0=In/1=Out */
GP_DIR_1 = 1<<17, /* IO_1 direct, 0=In/1=Out */
GP_DIR_0 = 1<<16, /* IO_0 direct, 0=In/1=Out */
GP_IO_9 = 1<<9, /* IO_9 pin */
GP_IO_8 = 1<<8, /* IO_8 pin */
GP_IO_7 = 1<<7, /* IO_7 pin */
GP_IO_6 = 1<<6, /* IO_6 pin */
GP_IO_5 = 1<<5, /* IO_5 pin */
GP_IO_4 = 1<<4, /* IO_4 pin */
GP_IO_3 = 1<<3, /* IO_3 pin */
GP_IO_2 = 1<<2, /* IO_2 pin */
GP_IO_1 = 1<<1, /* IO_1 pin */
GP_IO_0 = 1<<0, /* IO_0 pin */
};
/* Descriptor Bit Definition */
/* TxCtrl Transmit Buffer Control Field */
/* RxCtrl Receive Buffer Control Field */
enum {
BMU_OWN = 1<<31, /* OWN bit: 0=host/1=BMU */
BMU_STF = 1<<30, /* Start of Frame */
BMU_EOF = 1<<29, /* End of Frame */
BMU_IRQ_EOB = 1<<28, /* Req "End of Buffer" IRQ */
BMU_IRQ_EOF = 1<<27, /* Req "End of Frame" IRQ */
/* TxCtrl specific bits */
BMU_STFWD = 1<<26, /* (Tx) Store & Forward Frame */
BMU_NO_FCS = 1<<25, /* (Tx) Disable MAC FCS (CRC) generation */
BMU_SW = 1<<24, /* (Tx) 1 bit res. for SW use */
/* RxCtrl specific bits */
BMU_DEV_0 = 1<<26, /* (Rx) Transfer data to Dev0 */
BMU_STAT_VAL = 1<<25, /* (Rx) Rx Status Valid */
BMU_TIST_VAL = 1<<24, /* (Rx) Rx TimeStamp Valid */
/* Bit 23..16: BMU Check Opcodes */
BMU_CHECK = 0x55<<16, /* Default BMU check */
BMU_TCP_CHECK = 0x56<<16, /* Descr with TCP ext */
BMU_UDP_CHECK = 0x57<<16, /* Descr with UDP ext (YUKON only) */
BMU_BBC = 0xffffL, /* Bit 15.. 0: Buffer Byte Counter */
};
/* B2_BSC_CTRL 8 bit Blink Source Counter Control */
enum {
BSC_START = 1<<1, /* Start Blink Source Counter */
BSC_STOP = 1<<0, /* Stop Blink Source Counter */
};
/* B2_BSC_STAT 8 bit Blink Source Counter Status */
enum {
BSC_SRC = 1<<0, /* Blink Source, 0=Off / 1=On */
};
/* B2_BSC_TST 16 bit Blink Source Counter Test Reg */
enum {
BSC_T_ON = 1<<2, /* Test mode on */
BSC_T_OFF = 1<<1, /* Test mode off */
BSC_T_STEP = 1<<0, /* Test step */
};
/* B3_RAM_ADDR 32 bit RAM Address, to read or write */
/* Bit 31..19: reserved */
#define RAM_ADR_RAN 0x0007ffffL /* Bit 18.. 0: RAM Address Range */
/* RAM Interface Registers */
/* B3_RI_CTRL 16 bit RAM Iface Control Register */
enum {
RI_CLR_RD_PERR = 1<<9, /* Clear IRQ RAM Read Parity Err */
RI_CLR_WR_PERR = 1<<8, /* Clear IRQ RAM Write Parity Err*/
RI_RST_CLR = 1<<1, /* Clear RAM Interface Reset */
RI_RST_SET = 1<<0, /* Set RAM Interface Reset */
};
/* MAC Arbiter Registers */
/* B3_MA_TO_CTRL 16 bit MAC Arbiter Timeout Ctrl Reg */
enum {
MA_FOE_ON = 1<<3, /* XMAC Fast Output Enable ON */
MA_FOE_OFF = 1<<2, /* XMAC Fast Output Enable OFF */
MA_RST_CLR = 1<<1, /* Clear MAC Arbiter Reset */
MA_RST_SET = 1<<0, /* Set MAC Arbiter Reset */
};
/* Timeout values */
#define SK_MAC_TO_53 72 /* MAC arbiter timeout */
#define SK_PKT_TO_53 0x2000 /* Packet arbiter timeout */
#define SK_PKT_TO_MAX 0xffff /* Maximum value */
#define SK_RI_TO_53 36 /* RAM interface timeout */
/* Packet Arbiter Registers */
/* B3_PA_CTRL 16 bit Packet Arbiter Ctrl Register */
enum {
PA_CLR_TO_TX2 = 1<<13, /* Clear IRQ Packet Timeout TX2 */
PA_CLR_TO_TX1 = 1<<12, /* Clear IRQ Packet Timeout TX1 */
PA_CLR_TO_RX2 = 1<<11, /* Clear IRQ Packet Timeout RX2 */
PA_CLR_TO_RX1 = 1<<10, /* Clear IRQ Packet Timeout RX1 */
PA_ENA_TO_TX2 = 1<<9, /* Enable Timeout Timer TX2 */
PA_DIS_TO_TX2 = 1<<8, /* Disable Timeout Timer TX2 */
PA_ENA_TO_TX1 = 1<<7, /* Enable Timeout Timer TX1 */
PA_DIS_TO_TX1 = 1<<6, /* Disable Timeout Timer TX1 */
PA_ENA_TO_RX2 = 1<<5, /* Enable Timeout Timer RX2 */
PA_DIS_TO_RX2 = 1<<4, /* Disable Timeout Timer RX2 */
PA_ENA_TO_RX1 = 1<<3, /* Enable Timeout Timer RX1 */
PA_DIS_TO_RX1 = 1<<2, /* Disable Timeout Timer RX1 */
PA_RST_CLR = 1<<1, /* Clear MAC Arbiter Reset */
PA_RST_SET = 1<<0, /* Set MAC Arbiter Reset */
};
#define PA_ENA_TO_ALL (PA_ENA_TO_RX1 | PA_ENA_TO_RX2 |\
PA_ENA_TO_TX1 | PA_ENA_TO_TX2)
/* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */
/* TXA_ITI_INI 32 bit Tx Arb Interval Timer Init Val */
/* TXA_ITI_VAL 32 bit Tx Arb Interval Timer Value */
/* TXA_LIM_INI 32 bit Tx Arb Limit Counter Init Val */
/* TXA_LIM_VAL 32 bit Tx Arb Limit Counter Value */
#define TXA_MAX_VAL 0x00ffffffUL /* Bit 23.. 0: Max TXA Timer/Cnt Val */
/* TXA_CTRL 8 bit Tx Arbiter Control Register */
enum {
TXA_ENA_FSYNC = 1<<7, /* Enable force of sync Tx queue */
TXA_DIS_FSYNC = 1<<6, /* Disable force of sync Tx queue */
TXA_ENA_ALLOC = 1<<5, /* Enable alloc of free bandwidth */
TXA_DIS_ALLOC = 1<<4, /* Disable alloc of free bandwidth */
TXA_START_RC = 1<<3, /* Start sync Rate Control */
TXA_STOP_RC = 1<<2, /* Stop sync Rate Control */
TXA_ENA_ARB = 1<<1, /* Enable Tx Arbiter */
TXA_DIS_ARB = 1<<0, /* Disable Tx Arbiter */
};
/*
* Bank 4 - 5
*/
/* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */
enum {
TXA_ITI_INI = 0x0200,/* 32 bit Tx Arb Interval Timer Init Val*/
TXA_ITI_VAL = 0x0204,/* 32 bit Tx Arb Interval Timer Value */
TXA_LIM_INI = 0x0208,/* 32 bit Tx Arb Limit Counter Init Val */
TXA_LIM_VAL = 0x020c,/* 32 bit Tx Arb Limit Counter Value */
TXA_CTRL = 0x0210,/* 8 bit Tx Arbiter Control Register */
TXA_TEST = 0x0211,/* 8 bit Tx Arbiter Test Register */
TXA_STAT = 0x0212,/* 8 bit Tx Arbiter Status Register */
};
enum {
B6_EXT_REG = 0x0300,/* External registers (GENESIS only) */
B7_CFG_SPC = 0x0380,/* copy of the Configuration register */
B8_RQ1_REGS = 0x0400,/* Receive Queue 1 */
B8_RQ2_REGS = 0x0480,/* Receive Queue 2 */
B8_TS1_REGS = 0x0600,/* Transmit sync queue 1 */
B8_TA1_REGS = 0x0680,/* Transmit async queue 1 */
B8_TS2_REGS = 0x0700,/* Transmit sync queue 2 */
B8_TA2_REGS = 0x0780,/* Transmit sync queue 2 */
B16_RAM_REGS = 0x0800,/* RAM Buffer Registers */
};
/* Queue Register Offsets, use Q_ADDR() to access */
enum {
B8_Q_REGS = 0x0400, /* base of Queue registers */
Q_D = 0x00, /* 8*32 bit Current Descriptor */
Q_DA_L = 0x20, /* 32 bit Current Descriptor Address Low dWord */
Q_DA_H = 0x24, /* 32 bit Current Descriptor Address High dWord */
Q_AC_L = 0x28, /* 32 bit Current Address Counter Low dWord */
Q_AC_H = 0x2c, /* 32 bit Current Address Counter High dWord */
Q_BC = 0x30, /* 32 bit Current Byte Counter */
Q_CSR = 0x34, /* 32 bit BMU Control/Status Register */
Q_F = 0x38, /* 32 bit Flag Register */
Q_T1 = 0x3c, /* 32 bit Test Register 1 */
Q_T1_TR = 0x3c, /* 8 bit Test Register 1 Transfer SM */
Q_T1_WR = 0x3d, /* 8 bit Test Register 1 Write Descriptor SM */
Q_T1_RD = 0x3e, /* 8 bit Test Register 1 Read Descriptor SM */
Q_T1_SV = 0x3f, /* 8 bit Test Register 1 Supervisor SM */
Q_T2 = 0x40, /* 32 bit Test Register 2 */
Q_T3 = 0x44, /* 32 bit Test Register 3 */
};
#define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs))
/* RAM Buffer Register Offsets */
enum {
RB_START = 0x00,/* 32 bit RAM Buffer Start Address */
RB_END = 0x04,/* 32 bit RAM Buffer End Address */
RB_WP = 0x08,/* 32 bit RAM Buffer Write Pointer */
RB_RP = 0x0c,/* 32 bit RAM Buffer Read Pointer */
RB_RX_UTPP = 0x10,/* 32 bit Rx Upper Threshold, Pause Packet */
RB_RX_LTPP = 0x14,/* 32 bit Rx Lower Threshold, Pause Packet */
RB_RX_UTHP = 0x18,/* 32 bit Rx Upper Threshold, High Prio */
RB_RX_LTHP = 0x1c,/* 32 bit Rx Lower Threshold, High Prio */
/* 0x10 - 0x1f: reserved at Tx RAM Buffer Registers */
RB_PC = 0x20,/* 32 bit RAM Buffer Packet Counter */
RB_LEV = 0x24,/* 32 bit RAM Buffer Level Register */
RB_CTRL = 0x28,/* 32 bit RAM Buffer Control Register */
RB_TST1 = 0x29,/* 8 bit RAM Buffer Test Register 1 */
RB_TST2 = 0x2a,/* 8 bit RAM Buffer Test Register 2 */
};
/* Receive and Transmit Queues */
enum {
Q_R1 = 0x0000, /* Receive Queue 1 */
Q_R2 = 0x0080, /* Receive Queue 2 */
Q_XS1 = 0x0200, /* Synchronous Transmit Queue 1 */
Q_XA1 = 0x0280, /* Asynchronous Transmit Queue 1 */
Q_XS2 = 0x0300, /* Synchronous Transmit Queue 2 */
Q_XA2 = 0x0380, /* Asynchronous Transmit Queue 2 */
};
/* Different MAC Types */
enum {
SK_MAC_XMAC = 0, /* Xaqti XMAC II */
SK_MAC_GMAC = 1, /* Marvell GMAC */
};
/* Different PHY Types */
enum {
SK_PHY_XMAC = 0,/* integrated in XMAC II */
SK_PHY_BCOM = 1,/* Broadcom BCM5400 */
SK_PHY_LONE = 2,/* Level One LXT1000 [not supported]*/
SK_PHY_NAT = 3,/* National DP83891 [not supported] */
SK_PHY_MARV_COPPER= 4,/* Marvell 88E1011S */
SK_PHY_MARV_FIBER = 5,/* Marvell 88E1011S working on fiber */
};
/* PHY addresses (bits 12..8 of PHY address reg) */
enum {
PHY_ADDR_XMAC = 0<<8,
PHY_ADDR_BCOM = 1<<8,
/* GPHY address (bits 15..11 of SMI control reg) */
PHY_ADDR_MARV = 0,
};
#define RB_ADDR(offs, queue) (B16_RAM_REGS + (queue) + (offs))
/* Receive MAC FIFO, Receive LED, and Link_Sync regs (GENESIS only) */
enum {
RX_MFF_EA = 0x0c00,/* 32 bit Receive MAC FIFO End Address */
RX_MFF_WP = 0x0c04,/* 32 bit Receive MAC FIFO Write Pointer */
RX_MFF_RP = 0x0c0c,/* 32 bit Receive MAC FIFO Read Pointer */
RX_MFF_PC = 0x0c10,/* 32 bit Receive MAC FIFO Packet Cnt */
RX_MFF_LEV = 0x0c14,/* 32 bit Receive MAC FIFO Level */
RX_MFF_CTRL1 = 0x0c18,/* 16 bit Receive MAC FIFO Control Reg 1*/
RX_MFF_STAT_TO = 0x0c1a,/* 8 bit Receive MAC Status Timeout */
RX_MFF_TIST_TO = 0x0c1b,/* 8 bit Receive MAC Time Stamp Timeout */
RX_MFF_CTRL2 = 0x0c1c,/* 8 bit Receive MAC FIFO Control Reg 2*/
RX_MFF_TST1 = 0x0c1d,/* 8 bit Receive MAC FIFO Test Reg 1 */
RX_MFF_TST2 = 0x0c1e,/* 8 bit Receive MAC FIFO Test Reg 2 */
RX_LED_INI = 0x0c20,/* 32 bit Receive LED Cnt Init Value */
RX_LED_VAL = 0x0c24,/* 32 bit Receive LED Cnt Current Value */
RX_LED_CTRL = 0x0c28,/* 8 bit Receive LED Cnt Control Reg */
RX_LED_TST = 0x0c29,/* 8 bit Receive LED Cnt Test Register */
LNK_SYNC_INI = 0x0c30,/* 32 bit Link Sync Cnt Init Value */
LNK_SYNC_VAL = 0x0c34,/* 32 bit Link Sync Cnt Current Value */
LNK_SYNC_CTRL = 0x0c38,/* 8 bit Link Sync Cnt Control Register */
LNK_SYNC_TST = 0x0c39,/* 8 bit Link Sync Cnt Test Register */
LNK_LED_REG = 0x0c3c,/* 8 bit Link LED Register */
};
/* Receive and Transmit MAC FIFO Registers (GENESIS only) */
/* RX_MFF_CTRL1 16 bit Receive MAC FIFO Control Reg 1 */
enum {
MFF_ENA_RDY_PAT = 1<<13, /* Enable Ready Patch */
MFF_DIS_RDY_PAT = 1<<12, /* Disable Ready Patch */
MFF_ENA_TIM_PAT = 1<<11, /* Enable Timing Patch */
MFF_DIS_TIM_PAT = 1<<10, /* Disable Timing Patch */
MFF_ENA_ALM_FUL = 1<<9, /* Enable AlmostFull Sign */
MFF_DIS_ALM_FUL = 1<<8, /* Disable AlmostFull Sign */
MFF_ENA_PAUSE = 1<<7, /* Enable Pause Signaling */
MFF_DIS_PAUSE = 1<<6, /* Disable Pause Signaling */
MFF_ENA_FLUSH = 1<<5, /* Enable Frame Flushing */
MFF_DIS_FLUSH = 1<<4, /* Disable Frame Flushing */
MFF_ENA_TIST = 1<<3, /* Enable Time Stamp Gener */
MFF_DIS_TIST = 1<<2, /* Disable Time Stamp Gener */
MFF_CLR_INTIST = 1<<1, /* Clear IRQ No Time Stamp */
MFF_CLR_INSTAT = 1<<0, /* Clear IRQ No Status */
#define MFF_RX_CTRL_DEF MFF_ENA_TIM_PAT
};
/* TX_MFF_CTRL1 16 bit Transmit MAC FIFO Control Reg 1 */
enum {
MFF_CLR_PERR = 1<<15, /* Clear Parity Error IRQ */
/* Bit 14: reserved */
MFF_ENA_PKT_REC = 1<<13, /* Enable Packet Recovery */
MFF_DIS_PKT_REC = 1<<12, /* Disable Packet Recovery */
MFF_ENA_W4E = 1<<7, /* Enable Wait for Empty */
MFF_DIS_W4E = 1<<6, /* Disable Wait for Empty */
MFF_ENA_LOOPB = 1<<3, /* Enable Loopback */
MFF_DIS_LOOPB = 1<<2, /* Disable Loopback */
MFF_CLR_MAC_RST = 1<<1, /* Clear XMAC Reset */
MFF_SET_MAC_RST = 1<<0, /* Set XMAC Reset */
};
#define MFF_TX_CTRL_DEF (MFF_ENA_PKT_REC | MFF_ENA_TIM_PAT | MFF_ENA_FLUSH)
/* RX_MFF_TST2 8 bit Receive MAC FIFO Test Register 2 */
/* TX_MFF_TST2 8 bit Transmit MAC FIFO Test Register 2 */
enum {
MFF_WSP_T_ON = 1<<6, /* Tx: Write Shadow Ptr TestOn */
MFF_WSP_T_OFF = 1<<5, /* Tx: Write Shadow Ptr TstOff */
MFF_WSP_INC = 1<<4, /* Tx: Write Shadow Ptr Increment */
MFF_PC_DEC = 1<<3, /* Packet Counter Decrement */
MFF_PC_T_ON = 1<<2, /* Packet Counter Test On */
MFF_PC_T_OFF = 1<<1, /* Packet Counter Test Off */
MFF_PC_INC = 1<<0, /* Packet Counter Increment */
};
/* RX_MFF_TST1 8 bit Receive MAC FIFO Test Register 1 */
/* TX_MFF_TST1 8 bit Transmit MAC FIFO Test Register 1 */
enum {
MFF_WP_T_ON = 1<<6, /* Write Pointer Test On */
MFF_WP_T_OFF = 1<<5, /* Write Pointer Test Off */
MFF_WP_INC = 1<<4, /* Write Pointer Increm */
MFF_RP_T_ON = 1<<2, /* Read Pointer Test On */
MFF_RP_T_OFF = 1<<1, /* Read Pointer Test Off */
MFF_RP_DEC = 1<<0, /* Read Pointer Decrement */
};
/* RX_MFF_CTRL2 8 bit Receive MAC FIFO Control Reg 2 */
/* TX_MFF_CTRL2 8 bit Transmit MAC FIFO Control Reg 2 */
enum {
MFF_ENA_OP_MD = 1<<3, /* Enable Operation Mode */
MFF_DIS_OP_MD = 1<<2, /* Disable Operation Mode */
MFF_RST_CLR = 1<<1, /* Clear MAC FIFO Reset */
MFF_RST_SET = 1<<0, /* Set MAC FIFO Reset */
};
/* Link LED Counter Registers (GENESIS only) */
/* RX_LED_CTRL 8 bit Receive LED Cnt Control Reg */
/* TX_LED_CTRL 8 bit Transmit LED Cnt Control Reg */
/* LNK_SYNC_CTRL 8 bit Link Sync Cnt Control Register */
enum {
LED_START = 1<<2, /* Start Timer */
LED_STOP = 1<<1, /* Stop Timer */
LED_STATE = 1<<0, /* Rx/Tx: LED State, 1=LED on */
};
/* RX_LED_TST 8 bit Receive LED Cnt Test Register */
/* TX_LED_TST 8 bit Transmit LED Cnt Test Register */
/* LNK_SYNC_TST 8 bit Link Sync Cnt Test Register */
enum {
LED_T_ON = 1<<2, /* LED Counter Test mode On */
LED_T_OFF = 1<<1, /* LED Counter Test mode Off */
LED_T_STEP = 1<<0, /* LED Counter Step */
};
/* LNK_LED_REG 8 bit Link LED Register */
enum {
LED_BLK_ON = 1<<5, /* Link LED Blinking On */
LED_BLK_OFF = 1<<4, /* Link LED Blinking Off */
LED_SYNC_ON = 1<<3, /* Use Sync Wire to switch LED */
LED_SYNC_OFF = 1<<2, /* Disable Sync Wire Input */
LED_ON = 1<<1, /* switch LED on */
LED_OFF = 1<<0, /* switch LED off */
};
/* Receive GMAC FIFO (YUKON) */
enum {
RX_GMF_EA = 0x0c40,/* 32 bit Rx GMAC FIFO End Address */
RX_GMF_AF_THR = 0x0c44,/* 32 bit Rx GMAC FIFO Almost Full Thresh. */
RX_GMF_CTRL_T = 0x0c48,/* 32 bit Rx GMAC FIFO Control/Test */
RX_GMF_FL_MSK = 0x0c4c,/* 32 bit Rx GMAC FIFO Flush Mask */
RX_GMF_FL_THR = 0x0c50,/* 32 bit Rx GMAC FIFO Flush Threshold */
RX_GMF_WP = 0x0c60,/* 32 bit Rx GMAC FIFO Write Pointer */
RX_GMF_WLEV = 0x0c68,/* 32 bit Rx GMAC FIFO Write Level */
RX_GMF_RP = 0x0c70,/* 32 bit Rx GMAC FIFO Read Pointer */
RX_GMF_RLEV = 0x0c78,/* 32 bit Rx GMAC FIFO Read Level */
};
/* TXA_TEST 8 bit Tx Arbiter Test Register */
enum {
TXA_INT_T_ON = 1<<5, /* Tx Arb Interval Timer Test On */
TXA_INT_T_OFF = 1<<4, /* Tx Arb Interval Timer Test Off */
TXA_INT_T_STEP = 1<<3, /* Tx Arb Interval Timer Step */
TXA_LIM_T_ON = 1<<2, /* Tx Arb Limit Timer Test On */
TXA_LIM_T_OFF = 1<<1, /* Tx Arb Limit Timer Test Off */
TXA_LIM_T_STEP = 1<<0, /* Tx Arb Limit Timer Step */
};
/* TXA_STAT 8 bit Tx Arbiter Status Register */
enum {
TXA_PRIO_XS = 1<<0, /* sync queue has prio to send */
};
/* Q_BC 32 bit Current Byte Counter */
/* BMU Control Status Registers */
/* B0_R1_CSR 32 bit BMU Ctrl/Stat Rx Queue 1 */
/* B0_R2_CSR 32 bit BMU Ctrl/Stat Rx Queue 2 */
/* B0_XA1_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 1 */
/* B0_XS1_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 1 */
/* B0_XA2_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 2 */
/* B0_XS2_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 2 */
/* Q_CSR 32 bit BMU Control/Status Register */
enum {
CSR_SV_IDLE = 1<<24, /* BMU SM Idle */
CSR_DESC_CLR = 1<<21, /* Clear Reset for Descr */
CSR_DESC_SET = 1<<20, /* Set Reset for Descr */
CSR_FIFO_CLR = 1<<19, /* Clear Reset for FIFO */
CSR_FIFO_SET = 1<<18, /* Set Reset for FIFO */
CSR_HPI_RUN = 1<<17, /* Release HPI SM */
CSR_HPI_RST = 1<<16, /* Reset HPI SM to Idle */
CSR_SV_RUN = 1<<15, /* Release Supervisor SM */
CSR_SV_RST = 1<<14, /* Reset Supervisor SM */
CSR_DREAD_RUN = 1<<13, /* Release Descr Read SM */
CSR_DREAD_RST = 1<<12, /* Reset Descr Read SM */
CSR_DWRITE_RUN = 1<<11, /* Release Descr Write SM */
CSR_DWRITE_RST = 1<<10, /* Reset Descr Write SM */
CSR_TRANS_RUN = 1<<9, /* Release Transfer SM */
CSR_TRANS_RST = 1<<8, /* Reset Transfer SM */
CSR_ENA_POL = 1<<7, /* Enable Descr Polling */
CSR_DIS_POL = 1<<6, /* Disable Descr Polling */
CSR_STOP = 1<<5, /* Stop Rx/Tx Queue */
CSR_START = 1<<4, /* Start Rx/Tx Queue */
CSR_IRQ_CL_P = 1<<3, /* (Rx) Clear Parity IRQ */
CSR_IRQ_CL_B = 1<<2, /* Clear EOB IRQ */
CSR_IRQ_CL_F = 1<<1, /* Clear EOF IRQ */
CSR_IRQ_CL_C = 1<<0, /* Clear ERR IRQ */
};
#define CSR_SET_RESET (CSR_DESC_SET | CSR_FIFO_SET | CSR_HPI_RST |\
CSR_SV_RST | CSR_DREAD_RST | CSR_DWRITE_RST |\
CSR_TRANS_RST)
#define CSR_CLR_RESET (CSR_DESC_CLR | CSR_FIFO_CLR | CSR_HPI_RUN |\
CSR_SV_RUN | CSR_DREAD_RUN | CSR_DWRITE_RUN |\
CSR_TRANS_RUN)
/* Q_F 32 bit Flag Register */
enum {
F_ALM_FULL = 1<<27, /* Rx FIFO: almost full */
F_EMPTY = 1<<27, /* Tx FIFO: empty flag */
F_FIFO_EOF = 1<<26, /* Tag (EOF Flag) bit in FIFO */
F_WM_REACHED = 1<<25, /* Watermark reached */
F_FIFO_LEVEL = 0x1fL<<16, /* Bit 23..16: # of Qwords in FIFO */
F_WATER_MARK = 0x0007ffL, /* Bit 10.. 0: Watermark */
};
/* RAM Buffer Register Offsets, use RB_ADDR(Queue, Offs) to access */
/* RB_START 32 bit RAM Buffer Start Address */
/* RB_END 32 bit RAM Buffer End Address */
/* RB_WP 32 bit RAM Buffer Write Pointer */
/* RB_RP 32 bit RAM Buffer Read Pointer */
/* RB_RX_UTPP 32 bit Rx Upper Threshold, Pause Pack */
/* RB_RX_LTPP 32 bit Rx Lower Threshold, Pause Pack */
/* RB_RX_UTHP 32 bit Rx Upper Threshold, High Prio */
/* RB_RX_LTHP 32 bit Rx Lower Threshold, High Prio */
/* RB_PC 32 bit RAM Buffer Packet Counter */
/* RB_LEV 32 bit RAM Buffer Level Register */
#define RB_MSK 0x0007ffff /* Bit 18.. 0: RAM Buffer Pointer Bits */
/* RB_TST2 8 bit RAM Buffer Test Register 2 */
/* RB_TST1 8 bit RAM Buffer Test Register 1 */
/* RB_CTRL 8 bit RAM Buffer Control Register */
enum {
RB_ENA_STFWD = 1<<5, /* Enable Store & Forward */
RB_DIS_STFWD = 1<<4, /* Disable Store & Forward */
RB_ENA_OP_MD = 1<<3, /* Enable Operation Mode */
RB_DIS_OP_MD = 1<<2, /* Disable Operation Mode */
RB_RST_CLR = 1<<1, /* Clear RAM Buf STM Reset */
RB_RST_SET = 1<<0, /* Set RAM Buf STM Reset */
};
/* Transmit MAC FIFO and Transmit LED Registers (GENESIS only), */
enum {
TX_MFF_EA = 0x0d00,/* 32 bit Transmit MAC FIFO End Address */
TX_MFF_WP = 0x0d04,/* 32 bit Transmit MAC FIFO WR Pointer */
TX_MFF_WSP = 0x0d08,/* 32 bit Transmit MAC FIFO WR Shadow Ptr */
TX_MFF_RP = 0x0d0c,/* 32 bit Transmit MAC FIFO RD Pointer */
TX_MFF_PC = 0x0d10,/* 32 bit Transmit MAC FIFO Packet Cnt */
TX_MFF_LEV = 0x0d14,/* 32 bit Transmit MAC FIFO Level */
TX_MFF_CTRL1 = 0x0d18,/* 16 bit Transmit MAC FIFO Ctrl Reg 1 */
TX_MFF_WAF = 0x0d1a,/* 8 bit Transmit MAC Wait after flush */
TX_MFF_CTRL2 = 0x0d1c,/* 8 bit Transmit MAC FIFO Ctrl Reg 2 */
TX_MFF_TST1 = 0x0d1d,/* 8 bit Transmit MAC FIFO Test Reg 1 */
TX_MFF_TST2 = 0x0d1e,/* 8 bit Transmit MAC FIFO Test Reg 2 */
TX_LED_INI = 0x0d20,/* 32 bit Transmit LED Cnt Init Value */
TX_LED_VAL = 0x0d24,/* 32 bit Transmit LED Cnt Current Val */
TX_LED_CTRL = 0x0d28,/* 8 bit Transmit LED Cnt Control Reg */
TX_LED_TST = 0x0d29,/* 8 bit Transmit LED Cnt Test Reg */
};
/* Counter and Timer constants, for a host clock of 62.5 MHz */
#define SK_XMIT_DUR 0x002faf08UL /* 50 ms */
#define SK_BLK_DUR 0x01dcd650UL /* 500 ms */
#define SK_DPOLL_DEF 0x00ee6b28UL /* 250 ms at 62.5 MHz */
#define SK_DPOLL_MAX 0x00ffffffUL /* 268 ms at 62.5 MHz */
/* 215 ms at 78.12 MHz */
#define SK_FACT_62 100 /* is given in percent */
#define SK_FACT_53 85 /* on GENESIS: 53.12 MHz */
#define SK_FACT_78 125 /* on YUKON: 78.12 MHz */
/* Transmit GMAC FIFO (YUKON only) */
enum {
TX_GMF_EA = 0x0d40,/* 32 bit Tx GMAC FIFO End Address */
TX_GMF_AE_THR = 0x0d44,/* 32 bit Tx GMAC FIFO Almost Empty Thresh.*/
TX_GMF_CTRL_T = 0x0d48,/* 32 bit Tx GMAC FIFO Control/Test */
TX_GMF_WP = 0x0d60,/* 32 bit Tx GMAC FIFO Write Pointer */
TX_GMF_WSP = 0x0d64,/* 32 bit Tx GMAC FIFO Write Shadow Ptr. */
TX_GMF_WLEV = 0x0d68,/* 32 bit Tx GMAC FIFO Write Level */
TX_GMF_RP = 0x0d70,/* 32 bit Tx GMAC FIFO Read Pointer */
TX_GMF_RSTP = 0x0d74,/* 32 bit Tx GMAC FIFO Restart Pointer */
TX_GMF_RLEV = 0x0d78,/* 32 bit Tx GMAC FIFO Read Level */
/* Descriptor Poll Timer Registers */
B28_DPT_INI = 0x0e00,/* 24 bit Descriptor Poll Timer Init Val */
B28_DPT_VAL = 0x0e04,/* 24 bit Descriptor Poll Timer Curr Val */
B28_DPT_CTRL = 0x0e08,/* 8 bit Descriptor Poll Timer Ctrl Reg */
B28_DPT_TST = 0x0e0a,/* 8 bit Descriptor Poll Timer Test Reg */
/* Time Stamp Timer Registers (YUKON only) */
GMAC_TI_ST_VAL = 0x0e14,/* 32 bit Time Stamp Timer Curr Val */
GMAC_TI_ST_CTRL = 0x0e18,/* 8 bit Time Stamp Timer Ctrl Reg */
GMAC_TI_ST_TST = 0x0e1a,/* 8 bit Time Stamp Timer Test Reg */
};
enum {
LINKLED_OFF = 0x01,
LINKLED_ON = 0x02,
LINKLED_LINKSYNC_OFF = 0x04,
LINKLED_LINKSYNC_ON = 0x08,
LINKLED_BLINK_OFF = 0x10,
LINKLED_BLINK_ON = 0x20,
};
/* GMAC and GPHY Control Registers (YUKON only) */
enum {
GMAC_CTRL = 0x0f00,/* 32 bit GMAC Control Reg */
GPHY_CTRL = 0x0f04,/* 32 bit GPHY Control Reg */
GMAC_IRQ_SRC = 0x0f08,/* 8 bit GMAC Interrupt Source Reg */
GMAC_IRQ_MSK = 0x0f0c,/* 8 bit GMAC Interrupt Mask Reg */
GMAC_LINK_CTRL = 0x0f10,/* 16 bit Link Control Reg */
/* Wake-up Frame Pattern Match Control Registers (YUKON only) */
WOL_REG_OFFS = 0x20,/* HW-Bug: Address is + 0x20 against spec. */
WOL_CTRL_STAT = 0x0f20,/* 16 bit WOL Control/Status Reg */
WOL_MATCH_CTL = 0x0f22,/* 8 bit WOL Match Control Reg */
WOL_MATCH_RES = 0x0f23,/* 8 bit WOL Match Result Reg */
WOL_MAC_ADDR = 0x0f24,/* 32 bit WOL MAC Address */
WOL_PATT_RPTR = 0x0f2c,/* 8 bit WOL Pattern Read Pointer */
/* WOL Pattern Length Registers (YUKON only) */
WOL_PATT_LEN_LO = 0x0f30,/* 32 bit WOL Pattern Length 3..0 */
WOL_PATT_LEN_HI = 0x0f34,/* 24 bit WOL Pattern Length 6..4 */
/* WOL Pattern Counter Registers (YUKON only) */
WOL_PATT_CNT_0 = 0x0f38,/* 32 bit WOL Pattern Counter 3..0 */
WOL_PATT_CNT_4 = 0x0f3c,/* 24 bit WOL Pattern Counter 6..4 */
};
enum {
WOL_PATT_RAM_1 = 0x1000,/* WOL Pattern RAM Link 1 */
WOL_PATT_RAM_2 = 0x1400,/* WOL Pattern RAM Link 2 */
};
enum {
BASE_XMAC_1 = 0x2000,/* XMAC 1 registers */
BASE_GMAC_1 = 0x2800,/* GMAC 1 registers */
BASE_XMAC_2 = 0x3000,/* XMAC 2 registers */
BASE_GMAC_2 = 0x3800,/* GMAC 2 registers */
};
/*
* Receive Frame Status Encoding
*/
enum {
XMR_FS_LEN = 0x3fff<<18, /* Bit 31..18: Rx Frame Length */
XMR_FS_LEN_SHIFT = 18,
XMR_FS_2L_VLAN = 1<<17, /* Bit 17: tagged wh 2Lev VLAN ID*/
XMR_FS_1_VLAN = 1<<16, /* Bit 16: tagged wh 1ev VLAN ID*/
XMR_FS_BC = 1<<15, /* Bit 15: Broadcast Frame */
XMR_FS_MC = 1<<14, /* Bit 14: Multicast Frame */
XMR_FS_UC = 1<<13, /* Bit 13: Unicast Frame */
XMR_FS_BURST = 1<<11, /* Bit 11: Burst Mode */
XMR_FS_CEX_ERR = 1<<10, /* Bit 10: Carrier Ext. Error */
XMR_FS_802_3 = 1<<9, /* Bit 9: 802.3 Frame */
XMR_FS_COL_ERR = 1<<8, /* Bit 8: Collision Error */
XMR_FS_CAR_ERR = 1<<7, /* Bit 7: Carrier Event Error */
XMR_FS_LEN_ERR = 1<<6, /* Bit 6: In-Range Length Error */
XMR_FS_FRA_ERR = 1<<5, /* Bit 5: Framing Error */
XMR_FS_RUNT = 1<<4, /* Bit 4: Runt Frame */
XMR_FS_LNG_ERR = 1<<3, /* Bit 3: Giant (Jumbo) Frame */
XMR_FS_FCS_ERR = 1<<2, /* Bit 2: Frame Check Sequ Err */
XMR_FS_ERR = 1<<1, /* Bit 1: Frame Error */
XMR_FS_MCTRL = 1<<0, /* Bit 0: MAC Control Packet */
/*
* XMR_FS_ERR will be set if
* XMR_FS_FCS_ERR, XMR_FS_LNG_ERR, XMR_FS_RUNT,
* XMR_FS_FRA_ERR, XMR_FS_LEN_ERR, or XMR_FS_CEX_ERR
* is set. XMR_FS_LNG_ERR and XMR_FS_LEN_ERR will issue
* XMR_FS_ERR unless the corresponding bit in the Receive Command
* Register is set.
*/
};
/*
,* XMAC-PHY Registers, indirect addressed over the XMAC
*/
enum {
PHY_XMAC_CTRL = 0x00,/* 16 bit r/w PHY Control Register */
PHY_XMAC_STAT = 0x01,/* 16 bit r/w PHY Status Register */
PHY_XMAC_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */
PHY_XMAC_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */
PHY_XMAC_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
PHY_XMAC_AUNE_LP = 0x05,/* 16 bit r/o Link Partner Abi Reg */
PHY_XMAC_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
PHY_XMAC_NEPG = 0x07,/* 16 bit r/w Next Page Register */
PHY_XMAC_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */
PHY_XMAC_EXT_STAT = 0x0f,/* 16 bit r/o Ext Status Register */
PHY_XMAC_RES_ABI = 0x10,/* 16 bit r/o PHY Resolved Ability */
};
/*
* Broadcom-PHY Registers, indirect addressed over XMAC
*/
enum {
PHY_BCOM_CTRL = 0x00,/* 16 bit r/w PHY Control Register */
PHY_BCOM_STAT = 0x01,/* 16 bit r/o PHY Status Register */
PHY_BCOM_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */
PHY_BCOM_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */
PHY_BCOM_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
PHY_BCOM_AUNE_LP = 0x05,/* 16 bit r/o Link Part Ability Reg */
PHY_BCOM_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
PHY_BCOM_NEPG = 0x07,/* 16 bit r/w Next Page Register */
PHY_BCOM_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */
/* Broadcom-specific registers */
PHY_BCOM_1000T_CTRL = 0x09,/* 16 bit r/w 1000Base-T Control Reg */
PHY_BCOM_1000T_STAT = 0x0a,/* 16 bit r/o 1000Base-T Status Reg */
PHY_BCOM_EXT_STAT = 0x0f,/* 16 bit r/o Extended Status Reg */
PHY_BCOM_P_EXT_CTRL = 0x10,/* 16 bit r/w PHY Extended Ctrl Reg */
PHY_BCOM_P_EXT_STAT = 0x11,/* 16 bit r/o PHY Extended Stat Reg */
PHY_BCOM_RE_CTR = 0x12,/* 16 bit r/w Receive Error Counter */
PHY_BCOM_FC_CTR = 0x13,/* 16 bit r/w False Carrier Sense Cnt */
PHY_BCOM_RNO_CTR = 0x14,/* 16 bit r/w Receiver NOT_OK Cnt */
PHY_BCOM_AUX_CTRL = 0x18,/* 16 bit r/w Auxiliary Control Reg */
PHY_BCOM_AUX_STAT = 0x19,/* 16 bit r/o Auxiliary Stat Summary */
PHY_BCOM_INT_STAT = 0x1a,/* 16 bit r/o Interrupt Status Reg */
PHY_BCOM_INT_MASK = 0x1b,/* 16 bit r/w Interrupt Mask Reg */
};
/*
* Marvel-PHY Registers, indirect addressed over GMAC
*/
enum {
PHY_MARV_CTRL = 0x00,/* 16 bit r/w PHY Control Register */
PHY_MARV_STAT = 0x01,/* 16 bit r/o PHY Status Register */
PHY_MARV_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */
PHY_MARV_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */
PHY_MARV_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
PHY_MARV_AUNE_LP = 0x05,/* 16 bit r/o Link Part Ability Reg */
PHY_MARV_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
PHY_MARV_NEPG = 0x07,/* 16 bit r/w Next Page Register */
PHY_MARV_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */
/* Marvel-specific registers */
PHY_MARV_1000T_CTRL = 0x09,/* 16 bit r/w 1000Base-T Control Reg */
PHY_MARV_1000T_STAT = 0x0a,/* 16 bit r/o 1000Base-T Status Reg */
PHY_MARV_EXT_STAT = 0x0f,/* 16 bit r/o Extended Status Reg */
PHY_MARV_PHY_CTRL = 0x10,/* 16 bit r/w PHY Specific Ctrl Reg */
PHY_MARV_PHY_STAT = 0x11,/* 16 bit r/o PHY Specific Stat Reg */
PHY_MARV_INT_MASK = 0x12,/* 16 bit r/w Interrupt Mask Reg */
PHY_MARV_INT_STAT = 0x13,/* 16 bit r/o Interrupt Status Reg */
PHY_MARV_EXT_CTRL = 0x14,/* 16 bit r/w Ext. PHY Specific Ctrl */
PHY_MARV_RXE_CNT = 0x15,/* 16 bit r/w Receive Error Counter */
PHY_MARV_EXT_ADR = 0x16,/* 16 bit r/w Ext. Ad. for Cable Diag. */
PHY_MARV_PORT_IRQ = 0x17,/* 16 bit r/o Port 0 IRQ (88E1111 only) */
PHY_MARV_LED_CTRL = 0x18,/* 16 bit r/w LED Control Reg */
PHY_MARV_LED_OVER = 0x19,/* 16 bit r/w Manual LED Override Reg */
PHY_MARV_EXT_CTRL_2 = 0x1a,/* 16 bit r/w Ext. PHY Specific Ctrl 2 */
PHY_MARV_EXT_P_STAT = 0x1b,/* 16 bit r/w Ext. PHY Spec. Stat Reg */
PHY_MARV_CABLE_DIAG = 0x1c,/* 16 bit r/o Cable Diagnostic Reg */
PHY_MARV_PAGE_ADDR = 0x1d,/* 16 bit r/w Extended Page Address Reg */
PHY_MARV_PAGE_DATA = 0x1e,/* 16 bit r/w Extended Page Data Reg */
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
PHY_MARV_FE_LED_PAR = 0x16,/* 16 bit r/w LED Parallel Select Reg. */
PHY_MARV_FE_LED_SER = 0x17,/* 16 bit r/w LED Stream Select S. LED */
PHY_MARV_FE_VCT_TX = 0x1a,/* 16 bit r/w VCT Reg. for TXP/N Pins */
PHY_MARV_FE_VCT_RX = 0x1b,/* 16 bit r/o VCT Reg. for RXP/N Pins */
PHY_MARV_FE_SPEC_2 = 0x1c,/* 16 bit r/w Specific Control Reg. 2 */
};
enum {
PHY_CT_RESET = 1<<15, /* Bit 15: (sc) clear all PHY related regs */
PHY_CT_LOOP = 1<<14, /* Bit 14: enable Loopback over PHY */
PHY_CT_SPS_LSB = 1<<13, /* Bit 13: Speed select, lower bit */
PHY_CT_ANE = 1<<12, /* Bit 12: Auto-Negotiation Enabled */
PHY_CT_PDOWN = 1<<11, /* Bit 11: Power Down Mode */
PHY_CT_ISOL = 1<<10, /* Bit 10: Isolate Mode */
PHY_CT_RE_CFG = 1<<9, /* Bit 9: (sc) Restart Auto-Negotiation */
PHY_CT_DUP_MD = 1<<8, /* Bit 8: Duplex Mode */
PHY_CT_COL_TST = 1<<7, /* Bit 7: Collision Test enabled */
PHY_CT_SPS_MSB = 1<<6, /* Bit 6: Speed select, upper bit */
};
enum {
PHY_CT_SP1000 = PHY_CT_SPS_MSB, /* enable speed of 1000 Mbps */
PHY_CT_SP100 = PHY_CT_SPS_LSB, /* enable speed of 100 Mbps */
PHY_CT_SP10 = 0, /* enable speed of 10 Mbps */
};
enum {
PHY_ST_EXT_ST = 1<<8, /* Bit 8: Extended Status Present */
PHY_ST_PRE_SUP = 1<<6, /* Bit 6: Preamble Suppression */
PHY_ST_AN_OVER = 1<<5, /* Bit 5: Auto-Negotiation Over */
PHY_ST_REM_FLT = 1<<4, /* Bit 4: Remote Fault Condition Occured */
PHY_ST_AN_CAP = 1<<3, /* Bit 3: Auto-Negotiation Capability */
PHY_ST_LSYNC = 1<<2, /* Bit 2: Link Synchronized */
PHY_ST_JAB_DET = 1<<1, /* Bit 1: Jabber Detected */
PHY_ST_EXT_REG = 1<<0, /* Bit 0: Extended Register available */
};
enum {
PHY_I1_OUI_MSK = 0x3f<<10, /* Bit 15..10: Organization Unique ID */
PHY_I1_MOD_NUM = 0x3f<<4, /* Bit 9.. 4: Model Number */
PHY_I1_REV_MSK = 0xf, /* Bit 3.. 0: Revision Number */
};
/* different Broadcom PHY Ids */
enum {
PHY_BCOM_ID1_A1 = 0x6041,
PHY_BCOM_ID1_B2 = 0x6043,
PHY_BCOM_ID1_C0 = 0x6044,
PHY_BCOM_ID1_C5 = 0x6047,
};
/* different Marvell PHY Ids */
enum {
PHY_MARV_ID0_VAL= 0x0141, /* Marvell Unique Identifier */
PHY_MARV_ID1_B0 = 0x0C23, /* Yukon (PHY 88E1011) */
PHY_MARV_ID1_B2 = 0x0C25, /* Yukon-Plus (PHY 88E1011) */
PHY_MARV_ID1_C2 = 0x0CC2, /* Yukon-EC (PHY 88E1111) */
PHY_MARV_ID1_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */
};
/* Advertisement register bits */
enum {
PHY_AN_NXT_PG = 1<<15, /* Bit 15: Request Next Page */
PHY_AN_ACK = 1<<14, /* Bit 14: (ro) Acknowledge Received */
PHY_AN_RF = 1<<13, /* Bit 13: Remote Fault Bits */
PHY_AN_PAUSE_ASYM = 1<<11,/* Bit 11: Try for asymmetric */
PHY_AN_PAUSE_CAP = 1<<10, /* Bit 10: Try for pause */
PHY_AN_100BASE4 = 1<<9, /* Bit 9: Try for 100mbps 4k packets */
PHY_AN_100FULL = 1<<8, /* Bit 8: Try for 100mbps full-duplex */
PHY_AN_100HALF = 1<<7, /* Bit 7: Try for 100mbps half-duplex */
PHY_AN_10FULL = 1<<6, /* Bit 6: Try for 10mbps full-duplex */
PHY_AN_10HALF = 1<<5, /* Bit 5: Try for 10mbps half-duplex */
PHY_AN_CSMA = 1<<0, /* Bit 0: Only selector supported */
PHY_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
PHY_AN_FULL = PHY_AN_100FULL | PHY_AN_10FULL | PHY_AN_CSMA,
PHY_AN_ALL = PHY_AN_10HALF | PHY_AN_10FULL |
PHY_AN_100HALF | PHY_AN_100FULL,
};
/* Xmac Specific */
enum {
PHY_X_AN_NXT_PG = 1<<15, /* Bit 15: Request Next Page */
PHY_X_AN_ACK = 1<<14, /* Bit 14: (ro) Acknowledge Received */
PHY_X_AN_RFB = 3<<12,/* Bit 13..12: Remote Fault Bits */
PHY_X_AN_PAUSE = 3<<7,/* Bit 8.. 7: Pause Bits */
PHY_X_AN_HD = 1<<6, /* Bit 6: Half Duplex */
PHY_X_AN_FD = 1<<5, /* Bit 5: Full Duplex */
};
/* Pause Bits (PHY_X_AN_PAUSE and PHY_X_RS_PAUSE) encoding */
enum {
PHY_X_P_NO_PAUSE = 0<<7,/* Bit 8..7: no Pause Mode */
PHY_X_P_SYM_MD = 1<<7, /* Bit 8..7: symmetric Pause Mode */
PHY_X_P_ASYM_MD = 2<<7,/* Bit 8..7: asymmetric Pause Mode */
PHY_X_P_BOTH_MD = 3<<7,/* Bit 8..7: both Pause Mode */
};
/* Broadcom-Specific */
/***** PHY_BCOM_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
enum {
PHY_B_1000C_TEST = 7<<13,/* Bit 15..13: Test Modes */
PHY_B_1000C_MSE = 1<<12, /* Bit 12: Master/Slave Enable */
PHY_B_1000C_MSC = 1<<11, /* Bit 11: M/S Configuration */
PHY_B_1000C_RD = 1<<10, /* Bit 10: Repeater/DTE */
PHY_B_1000C_AFD = 1<<9, /* Bit 9: Advertise Full Duplex */
PHY_B_1000C_AHD = 1<<8, /* Bit 8: Advertise Half Duplex */
};
/***** PHY_BCOM_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
/***** PHY_MARV_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
enum {
PHY_B_1000S_MSF = 1<<15, /* Bit 15: Master/Slave Fault */
PHY_B_1000S_MSR = 1<<14, /* Bit 14: Master/Slave Result */
PHY_B_1000S_LRS = 1<<13, /* Bit 13: Local Receiver Status */
PHY_B_1000S_RRS = 1<<12, /* Bit 12: Remote Receiver Status */
PHY_B_1000S_LP_FD = 1<<11, /* Bit 11: Link Partner can FD */
PHY_B_1000S_LP_HD = 1<<10, /* Bit 10: Link Partner can HD */
/* Bit 9..8: reserved */
PHY_B_1000S_IEC = 0xff, /* Bit 7..0: Idle Error Count */
};
/***** PHY_BCOM_EXT_STAT 16 bit r/o Extended Status Register *****/
enum {
PHY_B_ES_X_FD_CAP = 1<<15, /* Bit 15: 1000Base-X FD capable */
PHY_B_ES_X_HD_CAP = 1<<14, /* Bit 14: 1000Base-X HD capable */
PHY_B_ES_T_FD_CAP = 1<<13, /* Bit 13: 1000Base-T FD capable */
PHY_B_ES_T_HD_CAP = 1<<12, /* Bit 12: 1000Base-T HD capable */
};
/***** PHY_BCOM_P_EXT_CTRL 16 bit r/w PHY Extended Control Reg *****/
enum {
PHY_B_PEC_MAC_PHY = 1<<15, /* Bit 15: 10BIT/GMI-Interface */
PHY_B_PEC_DIS_CROSS = 1<<14, /* Bit 14: Disable MDI Crossover */
PHY_B_PEC_TX_DIS = 1<<13, /* Bit 13: Tx output Disabled */
PHY_B_PEC_INT_DIS = 1<<12, /* Bit 12: Interrupts Disabled */
PHY_B_PEC_F_INT = 1<<11, /* Bit 11: Force Interrupt */
PHY_B_PEC_BY_45 = 1<<10, /* Bit 10: Bypass 4B5B-Decoder */
PHY_B_PEC_BY_SCR = 1<<9, /* Bit 9: Bypass Scrambler */
PHY_B_PEC_BY_MLT3 = 1<<8, /* Bit 8: Bypass MLT3 Encoder */
PHY_B_PEC_BY_RXA = 1<<7, /* Bit 7: Bypass Rx Alignm. */
PHY_B_PEC_RES_SCR = 1<<6, /* Bit 6: Reset Scrambler */
PHY_B_PEC_EN_LTR = 1<<5, /* Bit 5: Ena LED Traffic Mode */
PHY_B_PEC_LED_ON = 1<<4, /* Bit 4: Force LED's on */
PHY_B_PEC_LED_OFF = 1<<3, /* Bit 3: Force LED's off */
PHY_B_PEC_EX_IPG = 1<<2, /* Bit 2: Extend Tx IPG Mode */
PHY_B_PEC_3_LED = 1<<1, /* Bit 1: Three Link LED mode */
PHY_B_PEC_HIGH_LA = 1<<0, /* Bit 0: GMII FIFO Elasticy */
};
/***** PHY_BCOM_P_EXT_STAT 16 bit r/o PHY Extended Status Reg *****/
enum {
PHY_B_PES_CROSS_STAT = 1<<13, /* Bit 13: MDI Crossover Status */
PHY_B_PES_INT_STAT = 1<<12, /* Bit 12: Interrupt Status */
PHY_B_PES_RRS = 1<<11, /* Bit 11: Remote Receiver Stat. */
PHY_B_PES_LRS = 1<<10, /* Bit 10: Local Receiver Stat. */
PHY_B_PES_LOCKED = 1<<9, /* Bit 9: Locked */
PHY_B_PES_LS = 1<<8, /* Bit 8: Link Status */
PHY_B_PES_RF = 1<<7, /* Bit 7: Remote Fault */
PHY_B_PES_CE_ER = 1<<6, /* Bit 6: Carrier Ext Error */
PHY_B_PES_BAD_SSD = 1<<5, /* Bit 5: Bad SSD */
PHY_B_PES_BAD_ESD = 1<<4, /* Bit 4: Bad ESD */
PHY_B_PES_RX_ER = 1<<3, /* Bit 3: Receive Error */
PHY_B_PES_TX_ER = 1<<2, /* Bit 2: Transmit Error */
PHY_B_PES_LOCK_ER = 1<<1, /* Bit 1: Lock Error */
PHY_B_PES_MLT3_ER = 1<<0, /* Bit 0: MLT3 code Error */
};
/* PHY_BCOM_AUNE_ADV 16 bit r/w Auto-Negotiation Advertisement *****/
/* PHY_BCOM_AUNE_LP 16 bit r/o Link Partner Ability Reg *****/
enum {
PHY_B_AN_RF = 1<<13, /* Bit 13: Remote Fault */
PHY_B_AN_ASP = 1<<11, /* Bit 11: Asymmetric Pause */
PHY_B_AN_PC = 1<<10, /* Bit 10: Pause Capable */
};
/***** PHY_BCOM_FC_CTR 16 bit r/w False Carrier Counter *****/
enum {
PHY_B_FC_CTR = 0xff, /* Bit 7..0: False Carrier Counter */
/***** PHY_BCOM_RNO_CTR 16 bit r/w Receive NOT_OK Counter *****/
PHY_B_RC_LOC_MSK = 0xff00, /* Bit 15..8: Local Rx NOT_OK cnt */
PHY_B_RC_REM_MSK = 0x00ff, /* Bit 7..0: Remote Rx NOT_OK cnt */
/***** PHY_BCOM_AUX_CTRL 16 bit r/w Auxiliary Control Reg *****/
PHY_B_AC_L_SQE = 1<<15, /* Bit 15: Low Squelch */
PHY_B_AC_LONG_PACK = 1<<14, /* Bit 14: Rx Long Packets */
PHY_B_AC_ER_CTRL = 3<<12,/* Bit 13..12: Edgerate Control */
/* Bit 11: reserved */
PHY_B_AC_TX_TST = 1<<10, /* Bit 10: Tx test bit, always 1 */
/* Bit 9.. 8: reserved */
PHY_B_AC_DIS_PRF = 1<<7, /* Bit 7: dis part resp filter */
/* Bit 6: reserved */
PHY_B_AC_DIS_PM = 1<<5, /* Bit 5: dis power management */
/* Bit 4: reserved */
PHY_B_AC_DIAG = 1<<3, /* Bit 3: Diagnostic Mode */
};
/***** PHY_BCOM_AUX_STAT 16 bit r/o Auxiliary Status Reg *****/
enum {
PHY_B_AS_AN_C = 1<<15, /* Bit 15: AutoNeg complete */
PHY_B_AS_AN_CA = 1<<14, /* Bit 14: AN Complete Ack */
PHY_B_AS_ANACK_D = 1<<13, /* Bit 13: AN Ack Detect */
PHY_B_AS_ANAB_D = 1<<12, /* Bit 12: AN Ability Detect */
PHY_B_AS_NPW = 1<<11, /* Bit 11: AN Next Page Wait */
PHY_B_AS_AN_RES_MSK = 7<<8,/* Bit 10..8: AN HDC */
PHY_B_AS_PDF = 1<<7, /* Bit 7: Parallel Detect. Fault */
PHY_B_AS_RF = 1<<6, /* Bit 6: Remote Fault */
PHY_B_AS_ANP_R = 1<<5, /* Bit 5: AN Page Received */
PHY_B_AS_LP_ANAB = 1<<4, /* Bit 4: LP AN Ability */
PHY_B_AS_LP_NPAB = 1<<3, /* Bit 3: LP Next Page Ability */
PHY_B_AS_LS = 1<<2, /* Bit 2: Link Status */
PHY_B_AS_PRR = 1<<1, /* Bit 1: Pause Resolution-Rx */
PHY_B_AS_PRT = 1<<0, /* Bit 0: Pause Resolution-Tx */
};
#define PHY_B_AS_PAUSE_MSK (PHY_B_AS_PRR | PHY_B_AS_PRT)
/***** PHY_BCOM_INT_STAT 16 bit r/o Interrupt Status Reg *****/
/***** PHY_BCOM_INT_MASK 16 bit r/w Interrupt Mask Reg *****/
enum {
PHY_B_IS_PSE = 1<<14, /* Bit 14: Pair Swap Error */
PHY_B_IS_MDXI_SC = 1<<13, /* Bit 13: MDIX Status Change */
PHY_B_IS_HCT = 1<<12, /* Bit 12: counter above 32k */
PHY_B_IS_LCT = 1<<11, /* Bit 11: counter above 128 */
PHY_B_IS_AN_PR = 1<<10, /* Bit 10: Page Received */
PHY_B_IS_NO_HDCL = 1<<9, /* Bit 9: No HCD Link */
PHY_B_IS_NO_HDC = 1<<8, /* Bit 8: No HCD */
PHY_B_IS_NEG_USHDC = 1<<7, /* Bit 7: Negotiated Unsup. HCD */
PHY_B_IS_SCR_S_ER = 1<<6, /* Bit 6: Scrambler Sync Error */
PHY_B_IS_RRS_CHANGE = 1<<5, /* Bit 5: Remote Rx Stat Change */
PHY_B_IS_LRS_CHANGE = 1<<4, /* Bit 4: Local Rx Stat Change */
PHY_B_IS_DUP_CHANGE = 1<<3, /* Bit 3: Duplex Mode Change */
PHY_B_IS_LSP_CHANGE = 1<<2, /* Bit 2: Link Speed Change */
PHY_B_IS_LST_CHANGE = 1<<1, /* Bit 1: Link Status Changed */
PHY_B_IS_CRC_ER = 1<<0, /* Bit 0: CRC Error */
};
#define PHY_B_DEF_MSK \
(~(PHY_B_IS_PSE | PHY_B_IS_AN_PR | PHY_B_IS_DUP_CHANGE | \
PHY_B_IS_LSP_CHANGE | PHY_B_IS_LST_CHANGE))
/* Pause Bits (PHY_B_AN_ASP and PHY_B_AN_PC) encoding */
enum {
PHY_B_P_NO_PAUSE = 0<<10,/* Bit 11..10: no Pause Mode */
PHY_B_P_SYM_MD = 1<<10, /* Bit 11..10: symmetric Pause Mode */
PHY_B_P_ASYM_MD = 2<<10,/* Bit 11..10: asymmetric Pause Mode */
PHY_B_P_BOTH_MD = 3<<10,/* Bit 11..10: both Pause Mode */
};
/*
* Resolved Duplex mode and Capabilities (Aux Status Summary Reg)
*/
enum {
PHY_B_RES_1000FD = 7<<8,/* Bit 10..8: 1000Base-T Full Dup. */
PHY_B_RES_1000HD = 6<<8,/* Bit 10..8: 1000Base-T Half Dup. */
};
/** Marvell-Specific */
enum {
PHY_M_AN_NXT_PG = 1<<15, /* Request Next Page */
PHY_M_AN_ACK = 1<<14, /* (ro) Acknowledge Received */
PHY_M_AN_RF = 1<<13, /* Remote Fault */
PHY_M_AN_ASP = 1<<11, /* Asymmetric Pause */
PHY_M_AN_PC = 1<<10, /* MAC Pause implemented */
PHY_M_AN_100_T4 = 1<<9, /* Not cap. 100Base-T4 (always 0) */
PHY_M_AN_100_FD = 1<<8, /* Advertise 100Base-TX Full Duplex */
PHY_M_AN_100_HD = 1<<7, /* Advertise 100Base-TX Half Duplex */
PHY_M_AN_10_FD = 1<<6, /* Advertise 10Base-TX Full Duplex */
PHY_M_AN_10_HD = 1<<5, /* Advertise 10Base-TX Half Duplex */
PHY_M_AN_SEL_MSK =0x1f<<4, /* Bit 4.. 0: Selector Field Mask */
};
/* special defines for FIBER (88E1011S only) */
enum {
PHY_M_AN_ASP_X = 1<<8, /* Asymmetric Pause */
PHY_M_AN_PC_X = 1<<7, /* MAC Pause implemented */
PHY_M_AN_1000X_AHD = 1<<6, /* Advertise 10000Base-X Half Duplex */
PHY_M_AN_1000X_AFD = 1<<5, /* Advertise 10000Base-X Full Duplex */
};
/* Pause Bits (PHY_M_AN_ASP_X and PHY_M_AN_PC_X) encoding */
enum {
PHY_M_P_NO_PAUSE_X = 0<<7,/* Bit 8.. 7: no Pause Mode */
PHY_M_P_SYM_MD_X = 1<<7, /* Bit 8.. 7: symmetric Pause Mode */
PHY_M_P_ASYM_MD_X = 2<<7,/* Bit 8.. 7: asymmetric Pause Mode */
PHY_M_P_BOTH_MD_X = 3<<7,/* Bit 8.. 7: both Pause Mode */
};
/***** PHY_MARV_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
enum {
PHY_M_1000C_TEST = 7<<13,/* Bit 15..13: Test Modes */
PHY_M_1000C_MSE = 1<<12, /* Manual Master/Slave Enable */
PHY_M_1000C_MSC = 1<<11, /* M/S Configuration (1=Master) */
PHY_M_1000C_MPD = 1<<10, /* Multi-Port Device */
PHY_M_1000C_AFD = 1<<9, /* Advertise Full Duplex */
PHY_M_1000C_AHD = 1<<8, /* Advertise Half Duplex */
};
/***** PHY_MARV_PHY_CTRL 16 bit r/w PHY Specific Ctrl Reg *****/
enum {
PHY_M_PC_TX_FFD_MSK = 3<<14,/* Bit 15..14: Tx FIFO Depth Mask */
PHY_M_PC_RX_FFD_MSK = 3<<12,/* Bit 13..12: Rx FIFO Depth Mask */
PHY_M_PC_ASS_CRS_TX = 1<<11, /* Assert CRS on Transmit */
PHY_M_PC_FL_GOOD = 1<<10, /* Force Link Good */
PHY_M_PC_EN_DET_MSK = 3<<8,/* Bit 9.. 8: Energy Detect Mask */
PHY_M_PC_ENA_EXT_D = 1<<7, /* Enable Ext. Distance (10BT) */
PHY_M_PC_MDIX_MSK = 3<<5,/* Bit 6.. 5: MDI/MDIX Config. Mask */
PHY_M_PC_DIS_125CLK = 1<<4, /* Disable 125 CLK */
PHY_M_PC_MAC_POW_UP = 1<<3, /* MAC Power up */
PHY_M_PC_SQE_T_ENA = 1<<2, /* SQE Test Enabled */
PHY_M_PC_POL_R_DIS = 1<<1, /* Polarity Reversal Disabled */
PHY_M_PC_DIS_JABBER = 1<<0, /* Disable Jabber */
};
enum {
PHY_M_PC_EN_DET = 2<<8, /* Energy Detect (Mode 1) */
PHY_M_PC_EN_DET_PLUS = 3<<8, /* Energy Detect Plus (Mode 2) */
};
#define PHY_M_PC_MDI_XMODE(x) (((x)<<5) & PHY_M_PC_MDIX_MSK)
enum {
PHY_M_PC_MAN_MDI = 0, /* 00 = Manual MDI configuration */
PHY_M_PC_MAN_MDIX = 1, /* 01 = Manual MDIX configuration */
PHY_M_PC_ENA_AUTO = 3, /* 11 = Enable Automatic Crossover */
};
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
enum {
PHY_M_PC_ENA_DTE_DT = 1<<15, /* Enable Data Terminal Equ. (DTE) Detect */
PHY_M_PC_ENA_ENE_DT = 1<<14, /* Enable Energy Detect (sense & pulse) */
PHY_M_PC_DIS_NLP_CK = 1<<13, /* Disable Normal Link Puls (NLP) Check */
PHY_M_PC_ENA_LIP_NP = 1<<12, /* Enable Link Partner Next Page Reg. */
PHY_M_PC_DIS_NLP_GN = 1<<11, /* Disable Normal Link Puls Generation */
PHY_M_PC_DIS_SCRAMB = 1<<9, /* Disable Scrambler */
PHY_M_PC_DIS_FEFI = 1<<8, /* Disable Far End Fault Indic. (FEFI) */
PHY_M_PC_SH_TP_SEL = 1<<6, /* Shielded Twisted Pair Select */
PHY_M_PC_RX_FD_MSK = 3<<2,/* Bit 3.. 2: Rx FIFO Depth Mask */
};
/***** PHY_MARV_PHY_STAT 16 bit r/o PHY Specific Status Reg *****/
enum {
PHY_M_PS_SPEED_MSK = 3<<14, /* Bit 15..14: Speed Mask */
PHY_M_PS_SPEED_1000 = 1<<15, /* 10 = 1000 Mbps */
PHY_M_PS_SPEED_100 = 1<<14, /* 01 = 100 Mbps */
PHY_M_PS_SPEED_10 = 0, /* 00 = 10 Mbps */
PHY_M_PS_FULL_DUP = 1<<13, /* Full Duplex */
PHY_M_PS_PAGE_REC = 1<<12, /* Page Received */
PHY_M_PS_SPDUP_RES = 1<<11, /* Speed & Duplex Resolved */
PHY_M_PS_LINK_UP = 1<<10, /* Link Up */
PHY_M_PS_CABLE_MSK = 7<<7, /* Bit 9.. 7: Cable Length Mask */
PHY_M_PS_MDI_X_STAT = 1<<6, /* MDI Crossover Stat (1=MDIX) */
PHY_M_PS_DOWNS_STAT = 1<<5, /* Downshift Status (1=downsh.) */
PHY_M_PS_ENDET_STAT = 1<<4, /* Energy Detect Status (1=act) */
PHY_M_PS_TX_P_EN = 1<<3, /* Tx Pause Enabled */
PHY_M_PS_RX_P_EN = 1<<2, /* Rx Pause Enabled */
PHY_M_PS_POL_REV = 1<<1, /* Polarity Reversed */
PHY_M_PS_JABBER = 1<<0, /* Jabber */
};
#define PHY_M_PS_PAUSE_MSK (PHY_M_PS_TX_P_EN | PHY_M_PS_RX_P_EN)
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
enum {
PHY_M_PS_DTE_DETECT = 1<<15, /* Data Terminal Equipment (DTE) Detected */
PHY_M_PS_RES_SPEED = 1<<14, /* Resolved Speed (1=100 Mbps, 0=10 Mbps */
};
enum {
PHY_M_IS_AN_ERROR = 1<<15, /* Auto-Negotiation Error */
PHY_M_IS_LSP_CHANGE = 1<<14, /* Link Speed Changed */
PHY_M_IS_DUP_CHANGE = 1<<13, /* Duplex Mode Changed */
PHY_M_IS_AN_PR = 1<<12, /* Page Received */
PHY_M_IS_AN_COMPL = 1<<11, /* Auto-Negotiation Completed */
PHY_M_IS_LST_CHANGE = 1<<10, /* Link Status Changed */
PHY_M_IS_SYMB_ERROR = 1<<9, /* Symbol Error */
PHY_M_IS_FALSE_CARR = 1<<8, /* False Carrier */
PHY_M_IS_FIFO_ERROR = 1<<7, /* FIFO Overflow/Underrun Error */
PHY_M_IS_MDI_CHANGE = 1<<6, /* MDI Crossover Changed */
PHY_M_IS_DOWNSH_DET = 1<<5, /* Downshift Detected */
PHY_M_IS_END_CHANGE = 1<<4, /* Energy Detect Changed */
PHY_M_IS_DTE_CHANGE = 1<<2, /* DTE Power Det. Status Changed */
PHY_M_IS_POL_CHANGE = 1<<1, /* Polarity Changed */
PHY_M_IS_JABBER = 1<<0, /* Jabber */
PHY_M_IS_DEF_MSK = PHY_M_IS_AN_ERROR | PHY_M_IS_LSP_CHANGE |
PHY_M_IS_LST_CHANGE | PHY_M_IS_FIFO_ERROR,
PHY_M_IS_AN_MSK = PHY_M_IS_AN_ERROR | PHY_M_IS_AN_COMPL,
};
/***** PHY_MARV_EXT_CTRL 16 bit r/w Ext. PHY Specific Ctrl *****/
enum {
PHY_M_EC_ENA_BC_EXT = 1<<15, /* Enable Block Carr. Ext. (88E1111 only) */
PHY_M_EC_ENA_LIN_LB = 1<<14, /* Enable Line Loopback (88E1111 only) */
PHY_M_EC_DIS_LINK_P = 1<<12, /* Disable Link Pulses (88E1111 only) */
PHY_M_EC_M_DSC_MSK = 3<<10, /* Bit 11..10: Master Downshift Counter */
/* (88E1011 only) */
PHY_M_EC_S_DSC_MSK = 3<<8,/* Bit 9.. 8: Slave Downshift Counter */
/* (88E1011 only) */
PHY_M_EC_M_DSC_MSK2 = 7<<9,/* Bit 11.. 9: Master Downshift Counter */
/* (88E1111 only) */
PHY_M_EC_DOWN_S_ENA = 1<<8, /* Downshift Enable (88E1111 only) */
/* !!! Errata in spec. (1 = disable) */
PHY_M_EC_RX_TIM_CT = 1<<7, /* RGMII Rx Timing Control*/
PHY_M_EC_MAC_S_MSK = 7<<4,/* Bit 6.. 4: Def. MAC interface speed */
PHY_M_EC_FIB_AN_ENA = 1<<3, /* Fiber Auto-Neg. Enable (88E1011S only) */
PHY_M_EC_DTE_D_ENA = 1<<2, /* DTE Detect Enable (88E1111 only) */
PHY_M_EC_TX_TIM_CT = 1<<1, /* RGMII Tx Timing Control */
PHY_M_EC_TRANS_DIS = 1<<0, /* Transmitter Disable (88E1111 only) */};
#define PHY_M_EC_M_DSC(x) ((x)<<10) /* 00=1x; 01=2x; 10=3x; 11=4x */
#define PHY_M_EC_S_DSC(x) ((x)<<8) /* 00=dis; 01=1x; 10=2x; 11=3x */
#define PHY_M_EC_MAC_S(x) ((x)<<4) /* 01X=0; 110=2.5; 111=25 (MHz) */
#define PHY_M_EC_M_DSC_2(x) ((x)<<9) /* 000=1x; 001=2x; 010=3x; 011=4x */
/* 100=5x; 101=6x; 110=7x; 111=8x */
enum {
MAC_TX_CLK_0_MHZ = 2,
MAC_TX_CLK_2_5_MHZ = 6,
MAC_TX_CLK_25_MHZ = 7,
};
/***** PHY_MARV_LED_CTRL 16 bit r/w LED Control Reg *****/
enum {
PHY_M_LEDC_DIS_LED = 1<<15, /* Disable LED */
PHY_M_LEDC_PULS_MSK = 7<<12,/* Bit 14..12: Pulse Stretch Mask */
PHY_M_LEDC_F_INT = 1<<11, /* Force Interrupt */
PHY_M_LEDC_BL_R_MSK = 7<<8,/* Bit 10.. 8: Blink Rate Mask */
PHY_M_LEDC_DP_C_LSB = 1<<7, /* Duplex Control (LSB, 88E1111 only) */
PHY_M_LEDC_TX_C_LSB = 1<<6, /* Tx Control (LSB, 88E1111 only) */
PHY_M_LEDC_LK_C_MSK = 7<<3,/* Bit 5.. 3: Link Control Mask */
/* (88E1111 only) */
};
enum {
PHY_M_LEDC_LINK_MSK = 3<<3,/* Bit 4.. 3: Link Control Mask */
/* (88E1011 only) */
PHY_M_LEDC_DP_CTRL = 1<<2, /* Duplex Control */
PHY_M_LEDC_DP_C_MSB = 1<<2, /* Duplex Control (MSB, 88E1111 only) */
PHY_M_LEDC_RX_CTRL = 1<<1, /* Rx Activity / Link */
PHY_M_LEDC_TX_CTRL = 1<<0, /* Tx Activity / Link */
PHY_M_LEDC_TX_C_MSB = 1<<0, /* Tx Control (MSB, 88E1111 only) */
};
#define PHY_M_LED_PULS_DUR(x) (((x)<<12) & PHY_M_LEDC_PULS_MSK)
enum {
PULS_NO_STR = 0,/* no pulse stretching */
PULS_21MS = 1,/* 21 ms to 42 ms */
PULS_42MS = 2,/* 42 ms to 84 ms */
PULS_84MS = 3,/* 84 ms to 170 ms */
PULS_170MS = 4,/* 170 ms to 340 ms */
PULS_340MS = 5,/* 340 ms to 670 ms */
PULS_670MS = 6,/* 670 ms to 1.3 s */
PULS_1300MS = 7,/* 1.3 s to 2.7 s */
};
#define PHY_M_LED_BLINK_RT(x) (((x)<<8) & PHY_M_LEDC_BL_R_MSK)
enum {
BLINK_42MS = 0,/* 42 ms */
BLINK_84MS = 1,/* 84 ms */
BLINK_170MS = 2,/* 170 ms */
BLINK_340MS = 3,/* 340 ms */
BLINK_670MS = 4,/* 670 ms */
};
/***** PHY_MARV_LED_OVER 16 bit r/w Manual LED Override Reg *****/
#define PHY_M_LED_MO_SGMII(x) ((x)<<14) /* Bit 15..14: SGMII AN Timer */
/* Bit 13..12: reserved */
#define PHY_M_LED_MO_DUP(x) ((x)<<10) /* Bit 11..10: Duplex */
#define PHY_M_LED_MO_10(x) ((x)<<8) /* Bit 9.. 8: Link 10 */
#define PHY_M_LED_MO_100(x) ((x)<<6) /* Bit 7.. 6: Link 100 */
#define PHY_M_LED_MO_1000(x) ((x)<<4) /* Bit 5.. 4: Link 1000 */
#define PHY_M_LED_MO_RX(x) ((x)<<2) /* Bit 3.. 2: Rx */
#define PHY_M_LED_MO_TX(x) ((x)<<0) /* Bit 1.. 0: Tx */
enum {
MO_LED_NORM = 0,
MO_LED_BLINK = 1,
MO_LED_OFF = 2,
MO_LED_ON = 3,
};
/***** PHY_MARV_EXT_CTRL_2 16 bit r/w Ext. PHY Specific Ctrl 2 *****/
enum {
PHY_M_EC2_FI_IMPED = 1<<6, /* Fiber Input Impedance */
PHY_M_EC2_FO_IMPED = 1<<5, /* Fiber Output Impedance */
PHY_M_EC2_FO_M_CLK = 1<<4, /* Fiber Mode Clock Enable */
PHY_M_EC2_FO_BOOST = 1<<3, /* Fiber Output Boost */
PHY_M_EC2_FO_AM_MSK = 7,/* Bit 2.. 0: Fiber Output Amplitude */
};
/***** PHY_MARV_EXT_P_STAT 16 bit r/w Ext. PHY Specific Status *****/
enum {
PHY_M_FC_AUTO_SEL = 1<<15, /* Fiber/Copper Auto Sel. Dis. */
PHY_M_FC_AN_REG_ACC = 1<<14, /* Fiber/Copper AN Reg. Access */
PHY_M_FC_RESOLUTION = 1<<13, /* Fiber/Copper Resolution */
PHY_M_SER_IF_AN_BP = 1<<12, /* Ser. IF AN Bypass Enable */
PHY_M_SER_IF_BP_ST = 1<<11, /* Ser. IF AN Bypass Status */
PHY_M_IRQ_POLARITY = 1<<10, /* IRQ polarity */
PHY_M_DIS_AUT_MED = 1<<9, /* Disable Aut. Medium Reg. Selection */
/* (88E1111 only) */
/* Bit 9.. 4: reserved (88E1011 only) */
PHY_M_UNDOC1 = 1<<7, /* undocumented bit !! */
PHY_M_DTE_POW_STAT = 1<<4, /* DTE Power Status (88E1111 only) */
PHY_M_MODE_MASK = 0xf, /* Bit 3.. 0: copy of HWCFG MODE[3:0] */
};
/***** PHY_MARV_CABLE_DIAG 16 bit r/o Cable Diagnostic Reg *****/
enum {
PHY_M_CABD_ENA_TEST = 1<<15, /* Enable Test (Page 0) */
PHY_M_CABD_DIS_WAIT = 1<<15, /* Disable Waiting Period (Page 1) */
/* (88E1111 only) */
PHY_M_CABD_STAT_MSK = 3<<13, /* Bit 14..13: Status Mask */
PHY_M_CABD_AMPL_MSK = 0x1f<<8,/* Bit 12.. 8: Amplitude Mask */
/* (88E1111 only) */
PHY_M_CABD_DIST_MSK = 0xff, /* Bit 7.. 0: Distance Mask */
};
/* values for Cable Diagnostic Status (11=fail; 00=OK; 10=open; 01=short) */
enum {
CABD_STAT_NORMAL= 0,
CABD_STAT_SHORT = 1,
CABD_STAT_OPEN = 2,
CABD_STAT_FAIL = 3,
};
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
/***** PHY_MARV_FE_LED_PAR 16 bit r/w LED Parallel Select Reg. *****/
/* Bit 15..12: reserved (used internally) */
enum {
PHY_M_FELP_LED2_MSK = 0xf<<8, /* Bit 11.. 8: LED2 Mask (LINK) */
PHY_M_FELP_LED1_MSK = 0xf<<4, /* Bit 7.. 4: LED1 Mask (ACT) */
PHY_M_FELP_LED0_MSK = 0xf, /* Bit 3.. 0: LED0 Mask (SPEED) */
};
#define PHY_M_FELP_LED2_CTRL(x) (((x)<<8) & PHY_M_FELP_LED2_MSK)
#define PHY_M_FELP_LED1_CTRL(x) (((x)<<4) & PHY_M_FELP_LED1_MSK)
#define PHY_M_FELP_LED0_CTRL(x) (((x)<<0) & PHY_M_FELP_LED0_MSK)
enum {
LED_PAR_CTRL_COLX = 0x00,
LED_PAR_CTRL_ERROR = 0x01,
LED_PAR_CTRL_DUPLEX = 0x02,
LED_PAR_CTRL_DP_COL = 0x03,
LED_PAR_CTRL_SPEED = 0x04,
LED_PAR_CTRL_LINK = 0x05,
LED_PAR_CTRL_TX = 0x06,
LED_PAR_CTRL_RX = 0x07,
LED_PAR_CTRL_ACT = 0x08,
LED_PAR_CTRL_LNK_RX = 0x09,
LED_PAR_CTRL_LNK_AC = 0x0a,
LED_PAR_CTRL_ACT_BL = 0x0b,
LED_PAR_CTRL_TX_BL = 0x0c,
LED_PAR_CTRL_RX_BL = 0x0d,
LED_PAR_CTRL_COL_BL = 0x0e,
LED_PAR_CTRL_INACT = 0x0f
};
/*****,PHY_MARV_FE_SPEC_2 16 bit r/w Specific Control Reg. 2 *****/
enum {
PHY_M_FESC_DIS_WAIT = 1<<2, /* Disable TDR Waiting Period */
PHY_M_FESC_ENA_MCLK = 1<<1, /* Enable MAC Rx Clock in sleep mode */
PHY_M_FESC_SEL_CL_A = 1<<0, /* Select Class A driver (100B-TX) */
};
/***** PHY_MARV_PHY_CTRL (page 3) 16 bit r/w LED Control Reg. *****/
enum {
PHY_M_LEDC_LOS_MSK = 0xf<<12,/* Bit 15..12: LOS LED Ctrl. Mask */
PHY_M_LEDC_INIT_MSK = 0xf<<8, /* Bit 11.. 8: INIT LED Ctrl. Mask */
PHY_M_LEDC_STA1_MSK = 0xf<<4,/* Bit 7.. 4: STAT1 LED Ctrl. Mask */
PHY_M_LEDC_STA0_MSK = 0xf, /* Bit 3.. 0: STAT0 LED Ctrl. Mask */
};
#define PHY_M_LEDC_LOS_CTRL(x) (((x)<<12) & PHY_M_LEDC_LOS_MSK)
#define PHY_M_LEDC_INIT_CTRL(x) (((x)<<8) & PHY_M_LEDC_INIT_MSK)
#define PHY_M_LEDC_STA1_CTRL(x) (((x)<<4) & PHY_M_LEDC_STA1_MSK)
#define PHY_M_LEDC_STA0_CTRL(x) (((x)<<0) & PHY_M_LEDC_STA0_MSK)
/* GMAC registers */
/* Port Registers */
enum {
GM_GP_STAT = 0x0000, /* 16 bit r/o General Purpose Status */
GM_GP_CTRL = 0x0004, /* 16 bit r/w General Purpose Control */
GM_TX_CTRL = 0x0008, /* 16 bit r/w Transmit Control Reg. */
GM_RX_CTRL = 0x000c, /* 16 bit r/w Receive Control Reg. */
GM_TX_FLOW_CTRL = 0x0010, /* 16 bit r/w Transmit Flow-Control */
GM_TX_PARAM = 0x0014, /* 16 bit r/w Transmit Parameter Reg. */
GM_SERIAL_MODE = 0x0018, /* 16 bit r/w Serial Mode Register */
/* Source Address Registers */
GM_SRC_ADDR_1L = 0x001c, /* 16 bit r/w Source Address 1 (low) */
GM_SRC_ADDR_1M = 0x0020, /* 16 bit r/w Source Address 1 (middle) */
GM_SRC_ADDR_1H = 0x0024, /* 16 bit r/w Source Address 1 (high) */
GM_SRC_ADDR_2L = 0x0028, /* 16 bit r/w Source Address 2 (low) */
GM_SRC_ADDR_2M = 0x002c, /* 16 bit r/w Source Address 2 (middle) */
GM_SRC_ADDR_2H = 0x0030, /* 16 bit r/w Source Address 2 (high) */
/* Multicast Address Hash Registers */
GM_MC_ADDR_H1 = 0x0034, /* 16 bit r/w Multicast Address Hash 1 */
GM_MC_ADDR_H2 = 0x0038, /* 16 bit r/w Multicast Address Hash 2 */
GM_MC_ADDR_H3 = 0x003c, /* 16 bit r/w Multicast Address Hash 3 */
GM_MC_ADDR_H4 = 0x0040, /* 16 bit r/w Multicast Address Hash 4 */
/* Interrupt Source Registers */
GM_TX_IRQ_SRC = 0x0044, /* 16 bit r/o Tx Overflow IRQ Source */
GM_RX_IRQ_SRC = 0x0048, /* 16 bit r/o Rx Overflow IRQ Source */
GM_TR_IRQ_SRC = 0x004c, /* 16 bit r/o Tx/Rx Over. IRQ Source */
/* Interrupt Mask Registers */
GM_TX_IRQ_MSK = 0x0050, /* 16 bit r/w Tx Overflow IRQ Mask */
GM_RX_IRQ_MSK = 0x0054, /* 16 bit r/w Rx Overflow IRQ Mask */
GM_TR_IRQ_MSK = 0x0058, /* 16 bit r/w Tx/Rx Over. IRQ Mask */
/* Serial Management Interface (SMI) Registers */
GM_SMI_CTRL = 0x0080, /* 16 bit r/w SMI Control Register */
GM_SMI_DATA = 0x0084, /* 16 bit r/w SMI Data Register */
GM_PHY_ADDR = 0x0088, /* 16 bit r/w GPHY Address Register */
};
/* MIB Counters */
#define GM_MIB_CNT_BASE 0x0100 /* Base Address of MIB Counters */
#define GM_MIB_CNT_SIZE 44 /* Number of MIB Counters */
/*
* MIB Counters base address definitions (low word) -
* use offset 4 for access to high word (32 bit r/o)
*/
enum {
GM_RXF_UC_OK = GM_MIB_CNT_BASE + 0, /* Unicast Frames Received OK */
GM_RXF_BC_OK = GM_MIB_CNT_BASE + 8, /* Broadcast Frames Received OK */
GM_RXF_MPAUSE = GM_MIB_CNT_BASE + 16, /* Pause MAC Ctrl Frames Received */
GM_RXF_MC_OK = GM_MIB_CNT_BASE + 24, /* Multicast Frames Received OK */
GM_RXF_FCS_ERR = GM_MIB_CNT_BASE + 32, /* Rx Frame Check Seq. Error */
/* GM_MIB_CNT_BASE + 40: reserved */
GM_RXO_OK_LO = GM_MIB_CNT_BASE + 48, /* Octets Received OK Low */
GM_RXO_OK_HI = GM_MIB_CNT_BASE + 56, /* Octets Received OK High */
GM_RXO_ERR_LO = GM_MIB_CNT_BASE + 64, /* Octets Received Invalid Low */
GM_RXO_ERR_HI = GM_MIB_CNT_BASE + 72, /* Octets Received Invalid High */
GM_RXF_SHT = GM_MIB_CNT_BASE + 80, /* Frames <64 Byte Received OK */
GM_RXE_FRAG = GM_MIB_CNT_BASE + 88, /* Frames <64 Byte Received with FCS Err */
GM_RXF_64B = GM_MIB_CNT_BASE + 96, /* 64 Byte Rx Frame */
GM_RXF_127B = GM_MIB_CNT_BASE + 104, /* 65-127 Byte Rx Frame */
GM_RXF_255B = GM_MIB_CNT_BASE + 112, /* 128-255 Byte Rx Frame */
GM_RXF_511B = GM_MIB_CNT_BASE + 120, /* 256-511 Byte Rx Frame */
GM_RXF_1023B = GM_MIB_CNT_BASE + 128, /* 512-1023 Byte Rx Frame */
GM_RXF_1518B = GM_MIB_CNT_BASE + 136, /* 1024-1518 Byte Rx Frame */
GM_RXF_MAX_SZ = GM_MIB_CNT_BASE + 144, /* 1519-MaxSize Byte Rx Frame */
GM_RXF_LNG_ERR = GM_MIB_CNT_BASE + 152, /* Rx Frame too Long Error */
GM_RXF_JAB_PKT = GM_MIB_CNT_BASE + 160, /* Rx Jabber Packet Frame */
/* GM_MIB_CNT_BASE + 168: reserved */
GM_RXE_FIFO_OV = GM_MIB_CNT_BASE + 176, /* Rx FIFO overflow Event */
/* GM_MIB_CNT_BASE + 184: reserved */
GM_TXF_UC_OK = GM_MIB_CNT_BASE + 192, /* Unicast Frames Xmitted OK */
GM_TXF_BC_OK = GM_MIB_CNT_BASE + 200, /* Broadcast Frames Xmitted OK */
GM_TXF_MPAUSE = GM_MIB_CNT_BASE + 208, /* Pause MAC Ctrl Frames Xmitted */
GM_TXF_MC_OK = GM_MIB_CNT_BASE + 216, /* Multicast Frames Xmitted OK */
GM_TXO_OK_LO = GM_MIB_CNT_BASE + 224, /* Octets Transmitted OK Low */
GM_TXO_OK_HI = GM_MIB_CNT_BASE + 232, /* Octets Transmitted OK High */
GM_TXF_64B = GM_MIB_CNT_BASE + 240, /* 64 Byte Tx Frame */
GM_TXF_127B = GM_MIB_CNT_BASE + 248, /* 65-127 Byte Tx Frame */
GM_TXF_255B = GM_MIB_CNT_BASE + 256, /* 128-255 Byte Tx Frame */
GM_TXF_511B = GM_MIB_CNT_BASE + 264, /* 256-511 Byte Tx Frame */
GM_TXF_1023B = GM_MIB_CNT_BASE + 272, /* 512-1023 Byte Tx Frame */
GM_TXF_1518B = GM_MIB_CNT_BASE + 280, /* 1024-1518 Byte Tx Frame */
GM_TXF_MAX_SZ = GM_MIB_CNT_BASE + 288, /* 1519-MaxSize Byte Tx Frame */
GM_TXF_COL = GM_MIB_CNT_BASE + 304, /* Tx Collision */
GM_TXF_LAT_COL = GM_MIB_CNT_BASE + 312, /* Tx Late Collision */
GM_TXF_ABO_COL = GM_MIB_CNT_BASE + 320, /* Tx aborted due to Exces. Col. */
GM_TXF_MUL_COL = GM_MIB_CNT_BASE + 328, /* Tx Multiple Collision */
GM_TXF_SNG_COL = GM_MIB_CNT_BASE + 336, /* Tx Single Collision */
GM_TXE_FIFO_UR = GM_MIB_CNT_BASE + 344, /* Tx FIFO Underrun Event */
};
/* GMAC Bit Definitions */
/* GM_GP_STAT 16 bit r/o General Purpose Status Register */
enum {
GM_GPSR_SPEED = 1<<15, /* Bit 15: Port Speed (1 = 100 Mbps) */
GM_GPSR_DUPLEX = 1<<14, /* Bit 14: Duplex Mode (1 = Full) */
GM_GPSR_FC_TX_DIS = 1<<13, /* Bit 13: Tx Flow-Control Mode Disabled */
GM_GPSR_LINK_UP = 1<<12, /* Bit 12: Link Up Status */
GM_GPSR_PAUSE = 1<<11, /* Bit 11: Pause State */
GM_GPSR_TX_ACTIVE = 1<<10, /* Bit 10: Tx in Progress */
GM_GPSR_EXC_COL = 1<<9, /* Bit 9: Excessive Collisions Occured */
GM_GPSR_LAT_COL = 1<<8, /* Bit 8: Late Collisions Occured */
GM_GPSR_PHY_ST_CH = 1<<5, /* Bit 5: PHY Status Change */
GM_GPSR_GIG_SPEED = 1<<4, /* Bit 4: Gigabit Speed (1 = 1000 Mbps) */
GM_GPSR_PART_MODE = 1<<3, /* Bit 3: Partition mode */
GM_GPSR_FC_RX_DIS = 1<<2, /* Bit 2: Rx Flow-Control Mode Disabled */
GM_GPSR_PROM_EN = 1<<1, /* Bit 1: Promiscuous Mode Enabled */
};
/* GM_GP_CTRL 16 bit r/w General Purpose Control Register */
enum {
GM_GPCR_PROM_ENA = 1<<14, /* Bit 14: Enable Promiscuous Mode */
GM_GPCR_FC_TX_DIS = 1<<13, /* Bit 13: Disable Tx Flow-Control Mode */
GM_GPCR_TX_ENA = 1<<12, /* Bit 12: Enable Transmit */
GM_GPCR_RX_ENA = 1<<11, /* Bit 11: Enable Receive */
GM_GPCR_BURST_ENA = 1<<10, /* Bit 10: Enable Burst Mode */
GM_GPCR_LOOP_ENA = 1<<9, /* Bit 9: Enable MAC Loopback Mode */
GM_GPCR_PART_ENA = 1<<8, /* Bit 8: Enable Partition Mode */
GM_GPCR_GIGS_ENA = 1<<7, /* Bit 7: Gigabit Speed (1000 Mbps) */
GM_GPCR_FL_PASS = 1<<6, /* Bit 6: Force Link Pass */
GM_GPCR_DUP_FULL = 1<<5, /* Bit 5: Full Duplex Mode */
GM_GPCR_FC_RX_DIS = 1<<4, /* Bit 4: Disable Rx Flow-Control Mode */
GM_GPCR_SPEED_100 = 1<<3, /* Bit 3: Port Speed 100 Mbps */
GM_GPCR_AU_DUP_DIS = 1<<2, /* Bit 2: Disable Auto-Update Duplex */
GM_GPCR_AU_FCT_DIS = 1<<1, /* Bit 1: Disable Auto-Update Flow-C. */
GM_GPCR_AU_SPD_DIS = 1<<0, /* Bit 0: Disable Auto-Update Speed */
};
#define GM_GPCR_SPEED_1000 (GM_GPCR_GIGS_ENA | GM_GPCR_SPEED_100)
#define GM_GPCR_AU_ALL_DIS (GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS|GM_GPCR_AU_SPD_DIS)
/* GM_TX_CTRL 16 bit r/w Transmit Control Register */
enum {
GM_TXCR_FORCE_JAM = 1<<15, /* Bit 15: Force Jam / Flow-Control */
GM_TXCR_CRC_DIS = 1<<14, /* Bit 14: Disable insertion of CRC */
GM_TXCR_PAD_DIS = 1<<13, /* Bit 13: Disable padding of packets */
GM_TXCR_COL_THR_MSK = 1<<10, /* Bit 12..10: Collision Threshold */
};
#define TX_COL_THR(x) (((x)<<10) & GM_TXCR_COL_THR_MSK)
#define TX_COL_DEF 0x04
/* GM_RX_CTRL 16 bit r/w Receive Control Register */
enum {
GM_RXCR_UCF_ENA = 1<<15, /* Bit 15: Enable Unicast filtering */
GM_RXCR_MCF_ENA = 1<<14, /* Bit 14: Enable Multicast filtering */
GM_RXCR_CRC_DIS = 1<<13, /* Bit 13: Remove 4-byte CRC */
GM_RXCR_PASS_FC = 1<<12, /* Bit 12: Pass FC packets to FIFO */
};
/* GM_TX_PARAM 16 bit r/w Transmit Parameter Register */
enum {
GM_TXPA_JAMLEN_MSK = 0x03<<14, /* Bit 15..14: Jam Length */
GM_TXPA_JAMIPG_MSK = 0x1f<<9, /* Bit 13..9: Jam IPG */
GM_TXPA_JAMDAT_MSK = 0x1f<<4, /* Bit 8..4: IPG Jam to Data */
TX_JAM_LEN_DEF = 0x03,
TX_JAM_IPG_DEF = 0x0b,
TX_IPG_JAM_DEF = 0x1c,
};
#define TX_JAM_LEN_VAL(x) (((x)<<14) & GM_TXPA_JAMLEN_MSK)
#define TX_JAM_IPG_VAL(x) (((x)<<9) & GM_TXPA_JAMIPG_MSK)
#define TX_IPG_JAM_DATA(x) (((x)<<4) & GM_TXPA_JAMDAT_MSK)
/* GM_SERIAL_MODE 16 bit r/w Serial Mode Register */
enum {
GM_SMOD_DATABL_MSK = 0x1f<<11, /* Bit 15..11: Data Blinder (r/o) */
GM_SMOD_LIMIT_4 = 1<<10, /* Bit 10: 4 consecutive Tx trials */
GM_SMOD_VLAN_ENA = 1<<9, /* Bit 9: Enable VLAN (Max. Frame Len) */
GM_SMOD_JUMBO_ENA = 1<<8, /* Bit 8: Enable Jumbo (Max. Frame Len) */
GM_SMOD_IPG_MSK = 0x1f /* Bit 4..0: Inter-Packet Gap (IPG) */
};
#define DATA_BLIND_VAL(x) (((x)<<11) & GM_SMOD_DATABL_MSK)
#define DATA_BLIND_DEF 0x04
#define IPG_DATA_VAL(x) (x & GM_SMOD_IPG_MSK)
#define IPG_DATA_DEF 0x1e
/* GM_SMI_CTRL 16 bit r/w SMI Control Register */
enum {
GM_SMI_CT_PHY_A_MSK = 0x1f<<11,/* Bit 15..11: PHY Device Address */
GM_SMI_CT_REG_A_MSK = 0x1f<<6,/* Bit 10.. 6: PHY Register Address */
GM_SMI_CT_OP_RD = 1<<5, /* Bit 5: OpCode Read (0=Write)*/
GM_SMI_CT_RD_VAL = 1<<4, /* Bit 4: Read Valid (Read completed) */
GM_SMI_CT_BUSY = 1<<3, /* Bit 3: Busy (Operation in progress) */
};
#define GM_SMI_CT_PHY_AD(x) (((x)<<11) & GM_SMI_CT_PHY_A_MSK)
#define GM_SMI_CT_REG_AD(x) (((x)<<6) & GM_SMI_CT_REG_A_MSK)
/* GM_PHY_ADDR 16 bit r/w GPHY Address Register */
enum {
GM_PAR_MIB_CLR = 1<<5, /* Bit 5: Set MIB Clear Counter Mode */
GM_PAR_MIB_TST = 1<<4, /* Bit 4: MIB Load Counter (Test Mode) */
};
/* Receive Frame Status Encoding */
enum {
GMR_FS_LEN = 0xffff<<16, /* Bit 31..16: Rx Frame Length */
GMR_FS_LEN_SHIFT = 16,
GMR_FS_VLAN = 1<<13, /* Bit 13: VLAN Packet */
GMR_FS_JABBER = 1<<12, /* Bit 12: Jabber Packet */
GMR_FS_UN_SIZE = 1<<11, /* Bit 11: Undersize Packet */
GMR_FS_MC = 1<<10, /* Bit 10: Multicast Packet */
GMR_FS_BC = 1<<9, /* Bit 9: Broadcast Packet */
GMR_FS_RX_OK = 1<<8, /* Bit 8: Receive OK (Good Packet) */
GMR_FS_GOOD_FC = 1<<7, /* Bit 7: Good Flow-Control Packet */
GMR_FS_BAD_FC = 1<<6, /* Bit 6: Bad Flow-Control Packet */
GMR_FS_MII_ERR = 1<<5, /* Bit 5: MII Error */
GMR_FS_LONG_ERR = 1<<4, /* Bit 4: Too Long Packet */
GMR_FS_FRAGMENT = 1<<3, /* Bit 3: Fragment */
GMR_FS_CRC_ERR = 1<<1, /* Bit 1: CRC Error */
GMR_FS_RX_FF_OV = 1<<0, /* Bit 0: Rx FIFO Overflow */
/*
* GMR_FS_ANY_ERR (analogous to XMR_FS_ANY_ERR)
*/
GMR_FS_ANY_ERR = GMR_FS_CRC_ERR | GMR_FS_LONG_ERR |
GMR_FS_MII_ERR | GMR_FS_BAD_FC | GMR_FS_GOOD_FC |
GMR_FS_JABBER,
/* Rx GMAC FIFO Flush Mask (default) */
RX_FF_FL_DEF_MSK = GMR_FS_CRC_ERR | GMR_FS_RX_FF_OV |GMR_FS_MII_ERR |
GMR_FS_BAD_FC | GMR_FS_GOOD_FC | GMR_FS_UN_SIZE |
GMR_FS_JABBER,
};
/* RX_GMF_CTRL_T 32 bit Rx GMAC FIFO Control/Test */
enum {
GMF_WP_TST_ON = 1<<14, /* Write Pointer Test On */
GMF_WP_TST_OFF = 1<<13, /* Write Pointer Test Off */
GMF_WP_STEP = 1<<12, /* Write Pointer Step/Increment */
GMF_RP_TST_ON = 1<<10, /* Read Pointer Test On */
GMF_RP_TST_OFF = 1<<9, /* Read Pointer Test Off */
GMF_RP_STEP = 1<<8, /* Read Pointer Step/Increment */
GMF_RX_F_FL_ON = 1<<7, /* Rx FIFO Flush Mode On */
GMF_RX_F_FL_OFF = 1<<6, /* Rx FIFO Flush Mode Off */
GMF_CLI_RX_FO = 1<<5, /* Clear IRQ Rx FIFO Overrun */
GMF_CLI_RX_FC = 1<<4, /* Clear IRQ Rx Frame Complete */
GMF_OPER_ON = 1<<3, /* Operational Mode On */
GMF_OPER_OFF = 1<<2, /* Operational Mode Off */
GMF_RST_CLR = 1<<1, /* Clear GMAC FIFO Reset */
GMF_RST_SET = 1<<0, /* Set GMAC FIFO Reset */
RX_GMF_FL_THR_DEF = 0xa, /* flush threshold (default) */
};
/* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test */
enum {
GMF_WSP_TST_ON = 1<<18,/* Write Shadow Pointer Test On */
GMF_WSP_TST_OFF = 1<<17,/* Write Shadow Pointer Test Off */
GMF_WSP_STEP = 1<<16,/* Write Shadow Pointer Step/Increment */
GMF_CLI_TX_FU = 1<<6, /* Clear IRQ Tx FIFO Underrun */
GMF_CLI_TX_FC = 1<<5, /* Clear IRQ Tx Frame Complete */
GMF_CLI_TX_PE = 1<<4, /* Clear IRQ Tx Parity Error */
};
/* GMAC_TI_ST_CTRL 8 bit Time Stamp Timer Ctrl Reg (YUKON only) */
enum {
GMT_ST_START = 1<<2, /* Start Time Stamp Timer */
GMT_ST_STOP = 1<<1, /* Stop Time Stamp Timer */
GMT_ST_CLR_IRQ = 1<<0, /* Clear Time Stamp Timer IRQ */
};
/* GMAC_CTRL 32 bit GMAC Control Reg (YUKON only) */
enum {
GMC_H_BURST_ON = 1<<7, /* Half Duplex Burst Mode On */
GMC_H_BURST_OFF = 1<<6, /* Half Duplex Burst Mode Off */
GMC_F_LOOPB_ON = 1<<5, /* FIFO Loopback On */
GMC_F_LOOPB_OFF = 1<<4, /* FIFO Loopback Off */
GMC_PAUSE_ON = 1<<3, /* Pause On */
GMC_PAUSE_OFF = 1<<2, /* Pause Off */
GMC_RST_CLR = 1<<1, /* Clear GMAC Reset */
GMC_RST_SET = 1<<0, /* Set GMAC Reset */
};
/* GPHY_CTRL 32 bit GPHY Control Reg (YUKON only) */
enum {
GPC_SEL_BDT = 1<<28, /* Select Bi-Dir. Transfer for MDC/MDIO */
GPC_INT_POL_HI = 1<<27, /* IRQ Polarity is Active HIGH */
GPC_75_OHM = 1<<26, /* Use 75 Ohm Termination instead of 50 */
GPC_DIS_FC = 1<<25, /* Disable Automatic Fiber/Copper Detection */
GPC_DIS_SLEEP = 1<<24, /* Disable Energy Detect */
GPC_HWCFG_M_3 = 1<<23, /* HWCFG_MODE[3] */
GPC_HWCFG_M_2 = 1<<22, /* HWCFG_MODE[2] */
GPC_HWCFG_M_1 = 1<<21, /* HWCFG_MODE[1] */
GPC_HWCFG_M_0 = 1<<20, /* HWCFG_MODE[0] */
GPC_ANEG_0 = 1<<19, /* ANEG[0] */
GPC_ENA_XC = 1<<18, /* Enable MDI crossover */
GPC_DIS_125 = 1<<17, /* Disable 125 MHz clock */
GPC_ANEG_3 = 1<<16, /* ANEG[3] */
GPC_ANEG_2 = 1<<15, /* ANEG[2] */
GPC_ANEG_1 = 1<<14, /* ANEG[1] */
GPC_ENA_PAUSE = 1<<13, /* Enable Pause (SYM_OR_REM) */
GPC_PHYADDR_4 = 1<<12, /* Bit 4 of Phy Addr */
GPC_PHYADDR_3 = 1<<11, /* Bit 3 of Phy Addr */
GPC_PHYADDR_2 = 1<<10, /* Bit 2 of Phy Addr */
GPC_PHYADDR_1 = 1<<9, /* Bit 1 of Phy Addr */
GPC_PHYADDR_0 = 1<<8, /* Bit 0 of Phy Addr */
/* Bits 7..2: reserved */
GPC_RST_CLR = 1<<1, /* Clear GPHY Reset */
GPC_RST_SET = 1<<0, /* Set GPHY Reset */
};
#define GPC_HWCFG_GMII_COP (GPC_HWCFG_M_3|GPC_HWCFG_M_2 | GPC_HWCFG_M_1 | GPC_HWCFG_M_0)
#define GPC_HWCFG_GMII_FIB (GPC_HWCFG_M_2 | GPC_HWCFG_M_1 | GPC_HWCFG_M_0)
#define GPC_ANEG_ADV_ALL_M (GPC_ANEG_3 | GPC_ANEG_2 | GPC_ANEG_1 | GPC_ANEG_0)
/* forced speed and duplex mode (don't mix with other ANEG bits) */
#define GPC_FRC10MBIT_HALF 0
#define GPC_FRC10MBIT_FULL GPC_ANEG_0
#define GPC_FRC100MBIT_HALF GPC_ANEG_1
#define GPC_FRC100MBIT_FULL (GPC_ANEG_0 | GPC_ANEG_1)
/* auto-negotiation with limited advertised speeds */
/* mix only with master/slave settings (for copper) */
#define GPC_ADV_1000_HALF GPC_ANEG_2
#define GPC_ADV_1000_FULL GPC_ANEG_3
#define GPC_ADV_ALL (GPC_ANEG_2 | GPC_ANEG_3)
/* master/slave settings */
/* only for copper with 1000 Mbps */
#define GPC_FORCE_MASTER 0
#define GPC_FORCE_SLAVE GPC_ANEG_0
#define GPC_PREF_MASTER GPC_ANEG_1
#define GPC_PREF_SLAVE (GPC_ANEG_1 | GPC_ANEG_0)
/* GMAC_IRQ_SRC 8 bit GMAC Interrupt Source Reg (YUKON only) */
/* GMAC_IRQ_MSK 8 bit GMAC Interrupt Mask Reg (YUKON only) */
enum {
GM_IS_TX_CO_OV = 1<<5, /* Transmit Counter Overflow IRQ */
GM_IS_RX_CO_OV = 1<<4, /* Receive Counter Overflow IRQ */
GM_IS_TX_FF_UR = 1<<3, /* Transmit FIFO Underrun */
GM_IS_TX_COMPL = 1<<2, /* Frame Transmission Complete */
GM_IS_RX_FF_OR = 1<<1, /* Receive FIFO Overrun */
GM_IS_RX_COMPL = 1<<0, /* Frame Reception Complete */
#define GMAC_DEF_MSK (GM_IS_RX_FF_OR | GM_IS_TX_FF_UR)
/* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */
/* Bits 15.. 2: reserved */
GMLC_RST_CLR = 1<<1, /* Clear GMAC Link Reset */
GMLC_RST_SET = 1<<0, /* Set GMAC Link Reset */
/* WOL_CTRL_STAT 16 bit WOL Control/Status Reg */
WOL_CTL_LINK_CHG_OCC = 1<<15,
WOL_CTL_MAGIC_PKT_OCC = 1<<14,
WOL_CTL_PATTERN_OCC = 1<<13,
WOL_CTL_CLEAR_RESULT = 1<<12,
WOL_CTL_ENA_PME_ON_LINK_CHG = 1<<11,
WOL_CTL_DIS_PME_ON_LINK_CHG = 1<<10,
WOL_CTL_ENA_PME_ON_MAGIC_PKT = 1<<9,
WOL_CTL_DIS_PME_ON_MAGIC_PKT = 1<<8,
WOL_CTL_ENA_PME_ON_PATTERN = 1<<7,
WOL_CTL_DIS_PME_ON_PATTERN = 1<<6,
WOL_CTL_ENA_LINK_CHG_UNIT = 1<<5,
WOL_CTL_DIS_LINK_CHG_UNIT = 1<<4,
WOL_CTL_ENA_MAGIC_PKT_UNIT = 1<<3,
WOL_CTL_DIS_MAGIC_PKT_UNIT = 1<<2,
WOL_CTL_ENA_PATTERN_UNIT = 1<<1,
WOL_CTL_DIS_PATTERN_UNIT = 1<<0,
};
#define WOL_CTL_DEFAULT \
(WOL_CTL_DIS_PME_ON_LINK_CHG | \
WOL_CTL_DIS_PME_ON_PATTERN | \
WOL_CTL_DIS_PME_ON_MAGIC_PKT | \
WOL_CTL_DIS_LINK_CHG_UNIT | \
WOL_CTL_DIS_PATTERN_UNIT | \
WOL_CTL_DIS_MAGIC_PKT_UNIT)
/* WOL_MATCH_CTL 8 bit WOL Match Control Reg */
#define WOL_CTL_PATT_ENA(x) (1 << (x))
/* XMAC II registers */
enum {
XM_MMU_CMD = 0x0000, /* 16 bit r/w MMU Command Register */
XM_POFF = 0x0008, /* 32 bit r/w Packet Offset Register */
XM_BURST = 0x000c, /* 32 bit r/w Burst Register for half duplex*/
XM_1L_VLAN_TAG = 0x0010, /* 16 bit r/w One Level VLAN Tag ID */
XM_2L_VLAN_TAG = 0x0014, /* 16 bit r/w Two Level VLAN Tag ID */
XM_TX_CMD = 0x0020, /* 16 bit r/w Transmit Command Register */
XM_TX_RT_LIM = 0x0024, /* 16 bit r/w Transmit Retry Limit Register */
XM_TX_STIME = 0x0028, /* 16 bit r/w Transmit Slottime Register */
XM_TX_IPG = 0x002c, /* 16 bit r/w Transmit Inter Packet Gap */
XM_RX_CMD = 0x0030, /* 16 bit r/w Receive Command Register */
XM_PHY_ADDR = 0x0034, /* 16 bit r/w PHY Address Register */
XM_PHY_DATA = 0x0038, /* 16 bit r/w PHY Data Register */
XM_GP_PORT = 0x0040, /* 32 bit r/w General Purpose Port Register */
XM_IMSK = 0x0044, /* 16 bit r/w Interrupt Mask Register */
XM_ISRC = 0x0048, /* 16 bit r/o Interrupt Status Register */
XM_HW_CFG = 0x004c, /* 16 bit r/w Hardware Config Register */
XM_TX_LO_WM = 0x0060, /* 16 bit r/w Tx FIFO Low Water Mark */
XM_TX_HI_WM = 0x0062, /* 16 bit r/w Tx FIFO High Water Mark */
XM_TX_THR = 0x0064, /* 16 bit r/w Tx Request Threshold */
XM_HT_THR = 0x0066, /* 16 bit r/w Host Request Threshold */
XM_PAUSE_DA = 0x0068, /* NA reg r/w Pause Destination Address */
XM_CTL_PARA = 0x0070, /* 32 bit r/w Control Parameter Register */
XM_MAC_OPCODE = 0x0074, /* 16 bit r/w Opcode for MAC control frames */
XM_MAC_PTIME = 0x0076, /* 16 bit r/w Pause time for MAC ctrl frames*/
XM_TX_STAT = 0x0078, /* 32 bit r/o Tx Status LIFO Register */
XM_EXM_START = 0x0080, /* r/w Start Address of the EXM Regs */
#define XM_EXM(reg) (XM_EXM_START + ((reg) << 3))
};
enum {
XM_SRC_CHK = 0x0100, /* NA reg r/w Source Check Address Register */
XM_SA = 0x0108, /* NA reg r/w Station Address Register */
XM_HSM = 0x0110, /* 64 bit r/w Hash Match Address Registers */
XM_RX_LO_WM = 0x0118, /* 16 bit r/w Receive Low Water Mark */
XM_RX_HI_WM = 0x011a, /* 16 bit r/w Receive High Water Mark */
XM_RX_THR = 0x011c, /* 32 bit r/w Receive Request Threshold */
XM_DEV_ID = 0x0120, /* 32 bit r/o Device ID Register */
XM_MODE = 0x0124, /* 32 bit r/w Mode Register */
XM_LSA = 0x0128, /* NA reg r/o Last Source Register */
XM_TS_READ = 0x0130, /* 32 bit r/o Time Stamp Read Register */
XM_TS_LOAD = 0x0134, /* 32 bit r/o Time Stamp Load Value */
XM_STAT_CMD = 0x0200, /* 16 bit r/w Statistics Command Register */
XM_RX_CNT_EV = 0x0204, /* 32 bit r/o Rx Counter Event Register */
XM_TX_CNT_EV = 0x0208, /* 32 bit r/o Tx Counter Event Register */
XM_RX_EV_MSK = 0x020c, /* 32 bit r/w Rx Counter Event Mask */
XM_TX_EV_MSK = 0x0210, /* 32 bit r/w Tx Counter Event Mask */
XM_TXF_OK = 0x0280, /* 32 bit r/o Frames Transmitted OK Conuter */
XM_TXO_OK_HI = 0x0284, /* 32 bit r/o Octets Transmitted OK High Cnt*/
XM_TXO_OK_LO = 0x0288, /* 32 bit r/o Octets Transmitted OK Low Cnt */
XM_TXF_BC_OK = 0x028c, /* 32 bit r/o Broadcast Frames Xmitted OK */
XM_TXF_MC_OK = 0x0290, /* 32 bit r/o Multicast Frames Xmitted OK */
XM_TXF_UC_OK = 0x0294, /* 32 bit r/o Unicast Frames Xmitted OK */
XM_TXF_LONG = 0x0298, /* 32 bit r/o Tx Long Frame Counter */
XM_TXE_BURST = 0x029c, /* 32 bit r/o Tx Burst Event Counter */
XM_TXF_MPAUSE = 0x02a0, /* 32 bit r/o Tx Pause MAC Ctrl Frame Cnt */
XM_TXF_MCTRL = 0x02a4, /* 32 bit r/o Tx MAC Ctrl Frame Counter */
XM_TXF_SNG_COL = 0x02a8, /* 32 bit r/o Tx Single Collision Counter */
XM_TXF_MUL_COL = 0x02ac, /* 32 bit r/o Tx Multiple Collision Counter */
XM_TXF_ABO_COL = 0x02b0, /* 32 bit r/o Tx aborted due to Exces. Col. */
XM_TXF_LAT_COL = 0x02b4, /* 32 bit r/o Tx Late Collision Counter */
XM_TXF_DEF = 0x02b8, /* 32 bit r/o Tx Deferred Frame Counter */
XM_TXF_EX_DEF = 0x02bc, /* 32 bit r/o Tx Excessive Deferall Counter */
XM_TXE_FIFO_UR = 0x02c0, /* 32 bit r/o Tx FIFO Underrun Event Cnt */
XM_TXE_CS_ERR = 0x02c4, /* 32 bit r/o Tx Carrier Sense Error Cnt */
XM_TXP_UTIL = 0x02c8, /* 32 bit r/o Tx Utilization in % */
XM_TXF_64B = 0x02d0, /* 32 bit r/o 64 Byte Tx Frame Counter */
XM_TXF_127B = 0x02d4, /* 32 bit r/o 65-127 Byte Tx Frame Counter */
XM_TXF_255B = 0x02d8, /* 32 bit r/o 128-255 Byte Tx Frame Counter */
XM_TXF_511B = 0x02dc, /* 32 bit r/o 256-511 Byte Tx Frame Counter */
XM_TXF_1023B = 0x02e0, /* 32 bit r/o 512-1023 Byte Tx Frame Counter*/
XM_TXF_MAX_SZ = 0x02e4, /* 32 bit r/o 1024-MaxSize Byte Tx Frame Cnt*/
XM_RXF_OK = 0x0300, /* 32 bit r/o Frames Received OK */
XM_RXO_OK_HI = 0x0304, /* 32 bit r/o Octets Received OK High Cnt */
XM_RXO_OK_LO = 0x0308, /* 32 bit r/o Octets Received OK Low Counter*/
XM_RXF_BC_OK = 0x030c, /* 32 bit r/o Broadcast Frames Received OK */
XM_RXF_MC_OK = 0x0310, /* 32 bit r/o Multicast Frames Received OK */
XM_RXF_UC_OK = 0x0314, /* 32 bit r/o Unicast Frames Received OK */
XM_RXF_MPAUSE = 0x0318, /* 32 bit r/o Rx Pause MAC Ctrl Frame Cnt */
XM_RXF_MCTRL = 0x031c, /* 32 bit r/o Rx MAC Ctrl Frame Counter */
XM_RXF_INV_MP = 0x0320, /* 32 bit r/o Rx invalid Pause Frame Cnt */
XM_RXF_INV_MOC = 0x0324, /* 32 bit r/o Rx Frames with inv. MAC Opcode*/
XM_RXE_BURST = 0x0328, /* 32 bit r/o Rx Burst Event Counter */
XM_RXE_FMISS = 0x032c, /* 32 bit r/o Rx Missed Frames Event Cnt */
XM_RXF_FRA_ERR = 0x0330, /* 32 bit r/o Rx Framing Error Counter */
XM_RXE_FIFO_OV = 0x0334, /* 32 bit r/o Rx FIFO overflow Event Cnt */
XM_RXF_JAB_PKT = 0x0338, /* 32 bit r/o Rx Jabber Packet Frame Cnt */
XM_RXE_CAR_ERR = 0x033c, /* 32 bit r/o Rx Carrier Event Error Cnt */
XM_RXF_LEN_ERR = 0x0340, /* 32 bit r/o Rx in Range Length Error */
XM_RXE_SYM_ERR = 0x0344, /* 32 bit r/o Rx Symbol Error Counter */
XM_RXE_SHT_ERR = 0x0348, /* 32 bit r/o Rx Short Event Error Cnt */
XM_RXE_RUNT = 0x034c, /* 32 bit r/o Rx Runt Event Counter */
XM_RXF_LNG_ERR = 0x0350, /* 32 bit r/o Rx Frame too Long Error Cnt */
XM_RXF_FCS_ERR = 0x0354, /* 32 bit r/o Rx Frame Check Seq. Error Cnt */
XM_RXF_CEX_ERR = 0x035c, /* 32 bit r/o Rx Carrier Ext Error Frame Cnt*/
XM_RXP_UTIL = 0x0360, /* 32 bit r/o Rx Utilization in % */
XM_RXF_64B = 0x0368, /* 32 bit r/o 64 Byte Rx Frame Counter */
XM_RXF_127B = 0x036c, /* 32 bit r/o 65-127 Byte Rx Frame Counter */
XM_RXF_255B = 0x0370, /* 32 bit r/o 128-255 Byte Rx Frame Counter */
XM_RXF_511B = 0x0374, /* 32 bit r/o 256-511 Byte Rx Frame Counter */
XM_RXF_1023B = 0x0378, /* 32 bit r/o 512-1023 Byte Rx Frame Counter*/
XM_RXF_MAX_SZ = 0x037c, /* 32 bit r/o 1024-MaxSize Byte Rx Frame Cnt*/
};
/* XM_MMU_CMD 16 bit r/w MMU Command Register */
enum {
XM_MMU_PHY_RDY = 1<<12,/* Bit 12: PHY Read Ready */
XM_MMU_PHY_BUSY = 1<<11,/* Bit 11: PHY Busy */
XM_MMU_IGN_PF = 1<<10,/* Bit 10: Ignore Pause Frame */
XM_MMU_MAC_LB = 1<<9, /* Bit 9: Enable MAC Loopback */
XM_MMU_FRC_COL = 1<<7, /* Bit 7: Force Collision */
XM_MMU_SIM_COL = 1<<6, /* Bit 6: Simulate Collision */
XM_MMU_NO_PRE = 1<<5, /* Bit 5: No MDIO Preamble */
XM_MMU_GMII_FD = 1<<4, /* Bit 4: GMII uses Full Duplex */
XM_MMU_RAT_CTRL = 1<<3, /* Bit 3: Enable Rate Control */
XM_MMU_GMII_LOOP= 1<<2, /* Bit 2: PHY is in Loopback Mode */
XM_MMU_ENA_RX = 1<<1, /* Bit 1: Enable Receiver */
XM_MMU_ENA_TX = 1<<0, /* Bit 0: Enable Transmitter */
};
/* XM_TX_CMD 16 bit r/w Transmit Command Register */
enum {
XM_TX_BK2BK = 1<<6, /* Bit 6: Ignor Carrier Sense (Tx Bk2Bk)*/
XM_TX_ENC_BYP = 1<<5, /* Bit 5: Set Encoder in Bypass Mode */
XM_TX_SAM_LINE = 1<<4, /* Bit 4: (sc) Start utilization calculation */
XM_TX_NO_GIG_MD = 1<<3, /* Bit 3: Disable Carrier Extension */
XM_TX_NO_PRE = 1<<2, /* Bit 2: Disable Preamble Generation */
XM_TX_NO_CRC = 1<<1, /* Bit 1: Disable CRC Generation */
XM_TX_AUTO_PAD = 1<<0, /* Bit 0: Enable Automatic Padding */
};
/* XM_TX_RT_LIM 16 bit r/w Transmit Retry Limit Register */
#define XM_RT_LIM_MSK 0x1f /* Bit 4..0: Tx Retry Limit */
/* XM_TX_STIME 16 bit r/w Transmit Slottime Register */
#define XM_STIME_MSK 0x7f /* Bit 6..0: Tx Slottime bits */
/* XM_TX_IPG 16 bit r/w Transmit Inter Packet Gap */
#define XM_IPG_MSK 0xff /* Bit 7..0: IPG value bits */
/* XM_RX_CMD 16 bit r/w Receive Command Register */
enum {
XM_RX_LENERR_OK = 1<<8, /* Bit 8 don't set Rx Err bit for */
/* inrange error packets */
XM_RX_BIG_PK_OK = 1<<7, /* Bit 7 don't set Rx Err bit for */
/* jumbo packets */
XM_RX_IPG_CAP = 1<<6, /* Bit 6 repl. type field with IPG */
XM_RX_TP_MD = 1<<5, /* Bit 5: Enable transparent Mode */
XM_RX_STRIP_FCS = 1<<4, /* Bit 4: Enable FCS Stripping */
XM_RX_SELF_RX = 1<<3, /* Bit 3: Enable Rx of own packets */
XM_RX_SAM_LINE = 1<<2, /* Bit 2: (sc) Start utilization calculation */
XM_RX_STRIP_PAD = 1<<1, /* Bit 1: Strip pad bytes of Rx frames */
XM_RX_DIS_CEXT = 1<<0, /* Bit 0: Disable carrier ext. check */
};
/* XM_GP_PORT 32 bit r/w General Purpose Port Register */
enum {
XM_GP_ANIP = 1<<6, /* Bit 6: (ro) Auto-Neg. in progress */
XM_GP_FRC_INT = 1<<5, /* Bit 5: (sc) Force Interrupt */
XM_GP_RES_MAC = 1<<3, /* Bit 3: (sc) Reset MAC and FIFOs */
XM_GP_RES_STAT = 1<<2, /* Bit 2: (sc) Reset the statistics module */
XM_GP_INP_ASS = 1<<0, /* Bit 0: (ro) GP Input Pin asserted */
};
/* XM_IMSK 16 bit r/w Interrupt Mask Register */
/* XM_ISRC 16 bit r/o Interrupt Status Register */
enum {
XM_IS_LNK_AE = 1<<14, /* Bit 14: Link Asynchronous Event */
XM_IS_TX_ABORT = 1<<13, /* Bit 13: Transmit Abort, late Col. etc */
XM_IS_FRC_INT = 1<<12, /* Bit 12: Force INT bit set in GP */
XM_IS_INP_ASS = 1<<11, /* Bit 11: Input Asserted, GP bit 0 set */
XM_IS_LIPA_RC = 1<<10, /* Bit 10: Link Partner requests config */
XM_IS_RX_PAGE = 1<<9, /* Bit 9: Page Received */
XM_IS_TX_PAGE = 1<<8, /* Bit 8: Next Page Loaded for Transmit */
XM_IS_AND = 1<<7, /* Bit 7: Auto-Negotiation Done */
XM_IS_TSC_OV = 1<<6, /* Bit 6: Time Stamp Counter Overflow */
XM_IS_RXC_OV = 1<<5, /* Bit 5: Rx Counter Event Overflow */
XM_IS_TXC_OV = 1<<4, /* Bit 4: Tx Counter Event Overflow */
XM_IS_RXF_OV = 1<<3, /* Bit 3: Receive FIFO Overflow */
XM_IS_TXF_UR = 1<<2, /* Bit 2: Transmit FIFO Underrun */
XM_IS_TX_COMP = 1<<1, /* Bit 1: Frame Tx Complete */
XM_IS_RX_COMP = 1<<0, /* Bit 0: Frame Rx Complete */
};
#define XM_DEF_MSK (~(XM_IS_INP_ASS | XM_IS_LIPA_RC | XM_IS_RX_PAGE | \
XM_IS_AND | XM_IS_RXC_OV | XM_IS_TXC_OV | \
XM_IS_RXF_OV | XM_IS_TXF_UR))
/* XM_HW_CFG 16 bit r/w Hardware Config Register */
enum {
XM_HW_GEN_EOP = 1<<3, /* Bit 3: generate End of Packet pulse */
XM_HW_COM4SIG = 1<<2, /* Bit 2: use Comma Detect for Sig. Det.*/
XM_HW_GMII_MD = 1<<0, /* Bit 0: GMII Interface selected */
};
/* XM_TX_LO_WM 16 bit r/w Tx FIFO Low Water Mark */
/* XM_TX_HI_WM 16 bit r/w Tx FIFO High Water Mark */
#define XM_TX_WM_MSK 0x01ff /* Bit 9.. 0 Tx FIFO Watermark bits */
/* XM_TX_THR 16 bit r/w Tx Request Threshold */
/* XM_HT_THR 16 bit r/w Host Request Threshold */
/* XM_RX_THR 16 bit r/w Rx Request Threshold */
#define XM_THR_MSK 0x03ff /* Bit 10.. 0 Rx/Tx Request Threshold bits */
/* XM_TX_STAT 32 bit r/o Tx Status LIFO Register */
enum {
XM_ST_VALID = (1UL<<31), /* Bit 31: Status Valid */
XM_ST_BYTE_CNT = (0x3fffL<<17), /* Bit 30..17: Tx frame Length */
XM_ST_RETRY_CNT = (0x1fL<<12), /* Bit 16..12: Retry Count */
XM_ST_EX_COL = 1<<11, /* Bit 11: Excessive Collisions */
XM_ST_EX_DEF = 1<<10, /* Bit 10: Excessive Deferral */
XM_ST_BURST = 1<<9, /* Bit 9: p. xmitted in burst md*/
XM_ST_DEFER = 1<<8, /* Bit 8: packet was defered */
XM_ST_BC = 1<<7, /* Bit 7: Broadcast packet */
XM_ST_MC = 1<<6, /* Bit 6: Multicast packet */
XM_ST_UC = 1<<5, /* Bit 5: Unicast packet */
XM_ST_TX_UR = 1<<4, /* Bit 4: FIFO Underrun occured */
XM_ST_CS_ERR = 1<<3, /* Bit 3: Carrier Sense Error */
XM_ST_LAT_COL = 1<<2, /* Bit 2: Late Collision Error */
XM_ST_MUL_COL = 1<<1, /* Bit 1: Multiple Collisions */
XM_ST_SGN_COL = 1<<0, /* Bit 0: Single Collision */
};
/* XM_RX_LO_WM 16 bit r/w Receive Low Water Mark */
/* XM_RX_HI_WM 16 bit r/w Receive High Water Mark */
#define XM_RX_WM_MSK 0x03ff /* Bit 11.. 0: Rx FIFO Watermark bits */
/* XM_DEV_ID 32 bit r/o Device ID Register */
#define XM_DEV_OUI (0x00ffffffUL<<8) /* Bit 31..8: Device OUI */
#define XM_DEV_REV (0x07L << 5) /* Bit 7..5: Chip Rev Num */
/* XM_MODE 32 bit r/w Mode Register */
enum {
XM_MD_ENA_REJ = 1<<26, /* Bit 26: Enable Frame Reject */
XM_MD_SPOE_E = 1<<25, /* Bit 25: Send Pause on Edge */
/* extern generated */
XM_MD_TX_REP = 1<<24, /* Bit 24: Transmit Repeater Mode */
XM_MD_SPOFF_I = 1<<23, /* Bit 23: Send Pause on FIFO full */
/* intern generated */
XM_MD_LE_STW = 1<<22, /* Bit 22: Rx Stat Word in Little Endian */
XM_MD_TX_CONT = 1<<21, /* Bit 21: Send Continuous */
XM_MD_TX_PAUSE = 1<<20, /* Bit 20: (sc) Send Pause Frame */
XM_MD_ATS = 1<<19, /* Bit 19: Append Time Stamp */
XM_MD_SPOL_I = 1<<18, /* Bit 18: Send Pause on Low */
/* intern generated */
XM_MD_SPOH_I = 1<<17, /* Bit 17: Send Pause on High */
/* intern generated */
XM_MD_CAP = 1<<16, /* Bit 16: Check Address Pair */
XM_MD_ENA_HASH = 1<<15, /* Bit 15: Enable Hashing */
XM_MD_CSA = 1<<14, /* Bit 14: Check Station Address */
XM_MD_CAA = 1<<13, /* Bit 13: Check Address Array */
XM_MD_RX_MCTRL = 1<<12, /* Bit 12: Rx MAC Control Frame */
XM_MD_RX_RUNT = 1<<11, /* Bit 11: Rx Runt Frames */
XM_MD_RX_IRLE = 1<<10, /* Bit 10: Rx in Range Len Err Frame */
XM_MD_RX_LONG = 1<<9, /* Bit 9: Rx Long Frame */
XM_MD_RX_CRCE = 1<<8, /* Bit 8: Rx CRC Error Frame */
XM_MD_RX_ERR = 1<<7, /* Bit 7: Rx Error Frame */
XM_MD_DIS_UC = 1<<6, /* Bit 6: Disable Rx Unicast */
XM_MD_DIS_MC = 1<<5, /* Bit 5: Disable Rx Multicast */
XM_MD_DIS_BC = 1<<4, /* Bit 4: Disable Rx Broadcast */
XM_MD_ENA_PROM = 1<<3, /* Bit 3: Enable Promiscuous */
XM_MD_ENA_BE = 1<<2, /* Bit 2: Enable Big Endian */
XM_MD_FTF = 1<<1, /* Bit 1: (sc) Flush Tx FIFO */
XM_MD_FRF = 1<<0, /* Bit 0: (sc) Flush Rx FIFO */
};
#define XM_PAUSE_MODE (XM_MD_SPOE_E | XM_MD_SPOL_I | XM_MD_SPOH_I)
#define XM_DEF_MODE (XM_MD_RX_RUNT | XM_MD_RX_IRLE | XM_MD_RX_LONG |\
XM_MD_RX_CRCE | XM_MD_RX_ERR | XM_MD_CSA)
/* XM_STAT_CMD 16 bit r/w Statistics Command Register */
enum {
XM_SC_SNP_RXC = 1<<5, /* Bit 5: (sc) Snap Rx Counters */
XM_SC_SNP_TXC = 1<<4, /* Bit 4: (sc) Snap Tx Counters */
XM_SC_CP_RXC = 1<<3, /* Bit 3: Copy Rx Counters Continuously */
XM_SC_CP_TXC = 1<<2, /* Bit 2: Copy Tx Counters Continuously */
XM_SC_CLR_RXC = 1<<1, /* Bit 1: (sc) Clear Rx Counters */
XM_SC_CLR_TXC = 1<<0, /* Bit 0: (sc) Clear Tx Counters */
};
/* XM_RX_CNT_EV 32 bit r/o Rx Counter Event Register */
/* XM_RX_EV_MSK 32 bit r/w Rx Counter Event Mask */
enum {
XMR_MAX_SZ_OV = 1<<31, /* Bit 31: 1024-MaxSize Rx Cnt Ov*/
XMR_1023B_OV = 1<<30, /* Bit 30: 512-1023Byte Rx Cnt Ov*/
XMR_511B_OV = 1<<29, /* Bit 29: 256-511 Byte Rx Cnt Ov*/
XMR_255B_OV = 1<<28, /* Bit 28: 128-255 Byte Rx Cnt Ov*/
XMR_127B_OV = 1<<27, /* Bit 27: 65-127 Byte Rx Cnt Ov */
XMR_64B_OV = 1<<26, /* Bit 26: 64 Byte Rx Cnt Ov */
XMR_UTIL_OV = 1<<25, /* Bit 25: Rx Util Cnt Overflow */
XMR_UTIL_UR = 1<<24, /* Bit 24: Rx Util Cnt Underrun */
XMR_CEX_ERR_OV = 1<<23, /* Bit 23: CEXT Err Cnt Ov */
XMR_FCS_ERR_OV = 1<<21, /* Bit 21: Rx FCS Error Cnt Ov */
XMR_LNG_ERR_OV = 1<<20, /* Bit 20: Rx too Long Err Cnt Ov*/
XMR_RUNT_OV = 1<<19, /* Bit 19: Runt Event Cnt Ov */
XMR_SHT_ERR_OV = 1<<18, /* Bit 18: Rx Short Ev Err Cnt Ov*/
XMR_SYM_ERR_OV = 1<<17, /* Bit 17: Rx Sym Err Cnt Ov */
XMR_CAR_ERR_OV = 1<<15, /* Bit 15: Rx Carr Ev Err Cnt Ov */
XMR_JAB_PKT_OV = 1<<14, /* Bit 14: Rx Jabb Packet Cnt Ov */
XMR_FIFO_OV = 1<<13, /* Bit 13: Rx FIFO Ov Ev Cnt Ov */
XMR_FRA_ERR_OV = 1<<12, /* Bit 12: Rx Framing Err Cnt Ov */
XMR_FMISS_OV = 1<<11, /* Bit 11: Rx Missed Ev Cnt Ov */
XMR_BURST = 1<<10, /* Bit 10: Rx Burst Event Cnt Ov */
XMR_INV_MOC = 1<<9, /* Bit 9: Rx with inv. MAC OC Ov*/
XMR_INV_MP = 1<<8, /* Bit 8: Rx inv Pause Frame Ov */
XMR_MCTRL_OV = 1<<7, /* Bit 7: Rx MAC Ctrl-F Cnt Ov */
XMR_MPAUSE_OV = 1<<6, /* Bit 6: Rx Pause MAC Ctrl-F Ov*/
XMR_UC_OK_OV = 1<<5, /* Bit 5: Rx Unicast Frame CntOv*/
XMR_MC_OK_OV = 1<<4, /* Bit 4: Rx Multicast Cnt Ov */
XMR_BC_OK_OV = 1<<3, /* Bit 3: Rx Broadcast Cnt Ov */
XMR_OK_LO_OV = 1<<2, /* Bit 2: Octets Rx OK Low CntOv*/
XMR_OK_HI_OV = 1<<1, /* Bit 1: Octets Rx OK Hi Cnt Ov*/
XMR_OK_OV = 1<<0, /* Bit 0: Frames Received Ok Ov */
};
#define XMR_DEF_MSK (XMR_OK_LO_OV | XMR_OK_HI_OV)
/* XM_TX_CNT_EV 32 bit r/o Tx Counter Event Register */
/* XM_TX_EV_MSK 32 bit r/w Tx Counter Event Mask */
enum {
XMT_MAX_SZ_OV = 1<<25, /* Bit 25: 1024-MaxSize Tx Cnt Ov*/
XMT_1023B_OV = 1<<24, /* Bit 24: 512-1023Byte Tx Cnt Ov*/
XMT_511B_OV = 1<<23, /* Bit 23: 256-511 Byte Tx Cnt Ov*/
XMT_255B_OV = 1<<22, /* Bit 22: 128-255 Byte Tx Cnt Ov*/
XMT_127B_OV = 1<<21, /* Bit 21: 65-127 Byte Tx Cnt Ov */
XMT_64B_OV = 1<<20, /* Bit 20: 64 Byte Tx Cnt Ov */
XMT_UTIL_OV = 1<<19, /* Bit 19: Tx Util Cnt Overflow */
XMT_UTIL_UR = 1<<18, /* Bit 18: Tx Util Cnt Underrun */
XMT_CS_ERR_OV = 1<<17, /* Bit 17: Tx Carr Sen Err Cnt Ov*/
XMT_FIFO_UR_OV = 1<<16, /* Bit 16: Tx FIFO Ur Ev Cnt Ov */
XMT_EX_DEF_OV = 1<<15, /* Bit 15: Tx Ex Deferall Cnt Ov */
XMT_DEF = 1<<14, /* Bit 14: Tx Deferred Cnt Ov */
XMT_LAT_COL_OV = 1<<13, /* Bit 13: Tx Late Col Cnt Ov */
XMT_ABO_COL_OV = 1<<12, /* Bit 12: Tx abo dueto Ex Col Ov*/
XMT_MUL_COL_OV = 1<<11, /* Bit 11: Tx Mult Col Cnt Ov */
XMT_SNG_COL = 1<<10, /* Bit 10: Tx Single Col Cnt Ov */
XMT_MCTRL_OV = 1<<9, /* Bit 9: Tx MAC Ctrl Counter Ov*/
XMT_MPAUSE = 1<<8, /* Bit 8: Tx Pause MAC Ctrl-F Ov*/
XMT_BURST = 1<<7, /* Bit 7: Tx Burst Event Cnt Ov */
XMT_LONG = 1<<6, /* Bit 6: Tx Long Frame Cnt Ov */
XMT_UC_OK_OV = 1<<5, /* Bit 5: Tx Unicast Cnt Ov */
XMT_MC_OK_OV = 1<<4, /* Bit 4: Tx Multicast Cnt Ov */
XMT_BC_OK_OV = 1<<3, /* Bit 3: Tx Broadcast Cnt Ov */
XMT_OK_LO_OV = 1<<2, /* Bit 2: Octets Tx OK Low CntOv*/
XMT_OK_HI_OV = 1<<1, /* Bit 1: Octets Tx OK Hi Cnt Ov*/
XMT_OK_OV = 1<<0, /* Bit 0: Frames Tx Ok Ov */
};
#define XMT_DEF_MSK (XMT_OK_LO_OV | XMT_OK_HI_OV)
struct skge_rx_desc {
u32 control;
u32 next_offset;
u32 dma_lo;
u32 dma_hi;
u32 status;
u32 timestamp;
u16 csum2;
u16 csum1;
u16 csum2_start;
u16 csum1_start;
};
struct skge_tx_desc {
u32 control;
u32 next_offset;
u32 dma_lo;
u32 dma_hi;
u32 status;
u32 csum_offs;
u16 csum_write;
u16 csum_start;
u32 rsvd;
};
struct skge_element {
struct skge_element *next;
void *desc;
struct sk_buff *skb;
DECLARE_PCI_UNMAP_ADDR(mapaddr);
DECLARE_PCI_UNMAP_LEN(maplen);
};
struct skge_ring {
struct skge_element *to_clean;
struct skge_element *to_use;
struct skge_element *start;
unsigned long count;
};
struct skge_hw {
void __iomem *regs;
struct pci_dev *pdev;
u32 intr_mask;
struct net_device *dev[2];
u8 chip_id;
u8 chip_rev;
u8 copper;
u8 ports;
u32 ram_size;
u32 ram_offset;
u16 phy_addr;
struct tasklet_struct ext_tasklet;
spinlock_t phy_lock;
};
enum {
FLOW_MODE_NONE = 0, /* No Flow-Control */
FLOW_MODE_LOC_SEND = 1, /* Local station sends PAUSE */
FLOW_MODE_REM_SEND = 2, /* Symmetric or just remote */
FLOW_MODE_SYMMETRIC = 3, /* Both stations may send PAUSE */
};
struct skge_port {
u32 msg_enable;
struct skge_hw *hw;
struct net_device *netdev;
int port;
spinlock_t tx_lock;
struct skge_ring tx_ring;
struct skge_ring rx_ring;
struct net_device_stats net_stats;
u8 rx_csum;
u8 blink_on;
u8 flow_control;
u8 wol;
u8 autoneg; /* AUTONEG_ENABLE, AUTONEG_DISABLE */
u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */
u16 speed; /* SPEED_1000, SPEED_100, ... */
u32 advertising;
void *mem; /* PCI memory for rings */
dma_addr_t dma;
unsigned long mem_size;
unsigned int rx_buf_size;
};
/* Register accessor for memory mapped device */
static inline u32 skge_read32(const struct skge_hw *hw, int reg)
{
return readl(hw->regs + reg);
}
static inline u16 skge_read16(const struct skge_hw *hw, int reg)
{
return readw(hw->regs + reg);
}
static inline u8 skge_read8(const struct skge_hw *hw, int reg)
{
return readb(hw->regs + reg);
}
static inline void skge_write32(const struct skge_hw *hw, int reg, u32 val)
{
writel(val, hw->regs + reg);
}
static inline void skge_write16(const struct skge_hw *hw, int reg, u16 val)
{
writew(val, hw->regs + reg);
}
static inline void skge_write8(const struct skge_hw *hw, int reg, u8 val)
{
writeb(val, hw->regs + reg);
}
/* MAC Related Registers inside the device. */
#define SK_REG(port,reg) (((port)<<7)+(reg))
#define SK_XMAC_REG(port, reg) \
((BASE_XMAC_1 + (port) * (BASE_XMAC_2 - BASE_XMAC_1)) | (reg) << 1)
static inline u32 xm_read32(const struct skge_hw *hw, int port, int reg)
{
u32 v;
v = skge_read16(hw, SK_XMAC_REG(port, reg));
v |= (u32)skge_read16(hw, SK_XMAC_REG(port, reg+2)) << 16;
return v;
}
static inline u16 xm_read16(const struct skge_hw *hw, int port, int reg)
{
return skge_read16(hw, SK_XMAC_REG(port,reg));
}
static inline void xm_write32(const struct skge_hw *hw, int port, int r, u32 v)
{
skge_write16(hw, SK_XMAC_REG(port,r), v & 0xffff);
skge_write16(hw, SK_XMAC_REG(port,r+2), v >> 16);
}
static inline void xm_write16(const struct skge_hw *hw, int port, int r, u16 v)
{
skge_write16(hw, SK_XMAC_REG(port,r), v);
}
static inline void xm_outhash(const struct skge_hw *hw, int port, int reg,
const u8 *hash)
{
xm_write16(hw, port, reg, (u16)hash[0] | ((u16)hash[1] << 8));
xm_write16(hw, port, reg+2, (u16)hash[2] | ((u16)hash[3] << 8));
xm_write16(hw, port, reg+4, (u16)hash[4] | ((u16)hash[5] << 8));
xm_write16(hw, port, reg+6, (u16)hash[6] | ((u16)hash[7] << 8));
}
static inline void xm_outaddr(const struct skge_hw *hw, int port, int reg,
const u8 *addr)
{
xm_write16(hw, port, reg, (u16)addr[0] | ((u16)addr[1] << 8));
xm_write16(hw, port, reg+2, (u16)addr[2] | ((u16)addr[3] << 8));
xm_write16(hw, port, reg+4, (u16)addr[4] | ((u16)addr[5] << 8));
}
#define SK_GMAC_REG(port,reg) \
(BASE_GMAC_1 + (port) * (BASE_GMAC_2-BASE_GMAC_1) + (reg))
static inline u16 gma_read16(const struct skge_hw *hw, int port, int reg)
{
return skge_read16(hw, SK_GMAC_REG(port,reg));
}
static inline u32 gma_read32(const struct skge_hw *hw, int port, int reg)
{
return (u32) skge_read16(hw, SK_GMAC_REG(port,reg))
| ((u32)skge_read16(hw, SK_GMAC_REG(port,reg+4)) << 16);
}
static inline void gma_write16(const struct skge_hw *hw, int port, int r, u16 v)
{
skge_write16(hw, SK_GMAC_REG(port,r), v);
}
static inline void gma_set_addr(struct skge_hw *hw, int port, int reg,
const u8 *addr)
{
gma_write16(hw, port, reg, (u16) addr[0] | ((u16) addr[1] << 8));
gma_write16(hw, port, reg+4,(u16) addr[2] | ((u16) addr[3] << 8));
gma_write16(hw, port, reg+8,(u16) addr[4] | ((u16) addr[5] << 8));
}
#endif
