/*
* init_ohci1394_dma.c - Initializes physical DMA on all OHCI 1394 controllers
*
* Copyright (C) 2006-2007 Bernhard Kaindl <bk@suse.de>
*
* Derived from drivers/ieee1394/ohci1394.c and arch/x86/kernel/early-quirks.c
* this file has functions to:
* - scan the PCI very early on boot for all OHCI 1394-compliant controllers
* - reset and initialize them and make them join the IEEE1394 bus and
* - enable physical DMA on them to allow remote debugging
*
* All code and data is marked as __init and __initdata, respective as
* during boot, all OHCI1394 controllers may be claimed by the firewire
* stack and at this point, this code should not touch them anymore.
*
* To use physical DMA after the initialization of the firewire stack,
* be sure that the stack enables it and (re-)attach after the bus reset
* which may be caused by the firewire stack initialization.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software Foundation,
* Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
*/
#include <linux/interrupt.h> /* for ohci1394.h */
#include <linux/delay.h>
#include <linux/pci.h> /* for PCI defines */
#include <linux/init_ohci1394_dma.h>
#include <asm/pci-direct.h> /* for direct PCI config space access */
#include <asm/fixmap.h>
#include "ieee1394_types.h"
#include "ohci1394.h"
int __initdata init_ohci1394_dma_early;
/* Reads a PHY register of an OHCI-1394 controller */
static inline u8 __init get_phy_reg(struct ti_ohci *ohci, u8 addr)
{
int i;
quadlet_t r;
reg_write(ohci, OHCI1394_PhyControl, (addr << 8) | 0x00008000);
for (i = 0; i < OHCI_LOOP_COUNT; i++) {
if (reg_read(ohci, OHCI1394_PhyControl) & 0x80000000)
break;
mdelay(1);
}
r = reg_read(ohci, OHCI1394_PhyControl);
return (r & 0x00ff0000) >> 16;
}
/* Writes to a PHY register of an OHCI-1394 controller */
static inline void __init set_phy_reg(struct ti_ohci *ohci, u8 addr, u8 data)
{
int i;
reg_write(ohci, OHCI1394_PhyControl, (addr << 8) | data | 0x00004000);
for (i = 0; i < OHCI_LOOP_COUNT; i++) {
u32 r = reg_read(ohci, OHCI1394_PhyControl);
if (!(r & 0x00004000))
break;
mdelay(1);
}
}
/* Resets an OHCI-1394 controller (for sane state before initialization) */
static inline void __init init_ohci1394_soft_reset(struct ti_ohci *ohci) {
int i;
reg_write(ohci, OHCI1394_HCControlSet, OHCI1394_HCControl_softReset);
for (i = 0; i < OHCI_LOOP_COUNT; i++) {
if (!(reg_read(ohci, OHCI1394_HCControlSet)
& OHCI1394_HCControl_softReset))
break;
mdelay(1);
}
}
/* Basic OHCI-1394 register and port inititalization */
static inline void __init init_ohci1394_initialize(struct ti_ohci *ohci)
{
quadlet_t bus_options;
int num_ports, i;
/* Put some defaults to these undefined bus options */
bus_options = reg_read(ohci, OHCI1394_BusOptions);
bus_options |= 0x60000000; /* Enable CMC and ISC */
bus_options &= ~0x00ff0000; /* XXX: Set cyc_clk_acc to zero for now */
bus_options &= ~0x18000000; /* Disable PMC and BMC */
reg_write(ohci, OHCI1394_BusOptions, bus_options);
/* Set the bus number */
reg_write(ohci, OHCI1394_NodeID, 0x0000ffc0);
/* Enable posted writes */
reg_write(ohci, OHCI1394_HCControlSet,
OHCI1394_HCControl_postedWriteEnable);
/* Clear link control register */
reg_write(ohci, OHCI1394_LinkControlClear, 0xffffffff);
/* enable phys */
reg_write(ohci, OHCI1394_LinkControlSet,
OHCI1394_LinkControl_RcvPhyPkt);
/* Don't accept phy packets into AR request context */
reg_write(ohci, OHCI1394_LinkControlClear, 0x00000400);
/* Clear the Isochonouys interrupt masks */
reg_write(ohci, OHCI1394_IsoRecvIntMaskClear, 0xffffffff);
reg_write(ohci, OHCI1394_IsoRecvIntEventClear, 0xffffffff);
reg_write(ohci, OHCI1394_IsoXmitIntMaskClear, 0xffffffff);
reg_write(ohci, OHCI1394_IsoXmitIntEventClear, 0xffffffff);
/* Accept asyncronous transfer requests from all nodes for now */
reg_write(ohci,OHCI1394_AsReqFilterHiSet, 0x80000000);
/* Specify asyncronous transfer retries */
reg_write(ohci, OHCI1394_ATRetries,
OHCI1394_MAX_AT_REQ_RETRIES |
(OHCI1394_MAX_AT_RESP_RETRIES<<4) |
(OHCI1394_MAX_PHYS_RESP_RETRIES<<8));
/* We don't want hardware swapping */
reg_write(ohci, OHCI1394_HCControlClear, OHCI1394_HCControl_noByteSwap);
/* Enable link */
reg_write(ohci, OHCI1394_HCControlSet, OHCI1394_HCControl_linkEnable);
/* If anything is connected to a port, make sure it is enabled */
num_ports = get_phy_reg(ohci, 2) & 0xf;
for (i = 0; i < num_ports; i++) {
unsigned int status;
set_phy_reg(ohci, 7, i);
status = get_phy_reg(ohci, 8);
if (status & 0x20)
set_phy_reg(ohci, 8, status & ~1);
}
}
/**
* init_ohci1394_wait_for_busresets - wait until bus resets are completed
*
* OHCI1394 initialization itself and any device going on- or offline
* and any cable issue cause a IEEE1394 bus reset. The OHCI1394 spec
* specifies that physical DMA is disabled on each bus reset and it
* has to be enabled after each bus reset when needed. We resort
* to polling here because on early boot, we have no interrupts.
*/
static inline void __init init_ohci1394_wait_for_busresets(struct ti_ohci *ohci)
{
int i, events;
for (i=0; i < 9; i++) {
mdelay(200);
events = reg_read(ohci, OHCI1394_IntEventSet);
if (events & OHCI1394_busReset)
reg_write(ohci, OHCI1394_IntEventClear,
OHCI1394_busReset);
}
}
/**
* init_ohci1394_enable_physical_dma - Enable physical DMA for remote debugging
* This enables remote DMA access over IEEE1394 from every host for the low
* 4GB of address space. DMA accesses above 4GB are not available currently.
*/
static inline void __init init_ohci1394_enable_physical_dma(struct ti_ohci *hci)
{
reg_write(hci, OHCI1394_PhyReqFilterHiSet, 0xffffffff);
reg_write(hci, OHCI1394_PhyReqFilterLoSet, 0xffffffff);
reg_write(hci, OHCI1394_PhyUpperBound, 0xffff0000);
}
/**
* init_ohci1394_reset_and_init_dma - init controller and enable DMA
* This initializes the given controller and enables physical DMA engine in it.
*/
static inline void __init init_ohci1394_reset_and_init_dma(struct ti_ohci *ohci)
{
/* Start off with a soft reset, clears everything to a sane state. */
init_ohci1394_soft_reset(ohci);
/* Accessing some registers without LPS enabled may cause lock up */
reg_write(ohci, OHCI1394_HCControlSet, OHCI1394_HCControl_LPS);
/* Disable and clear interrupts */
reg_write(ohci, OHCI1394_IntEventClear, 0xffffffff);
reg_write(ohci, OHCI1394_IntMaskClear, 0xffffffff);
mdelay(50); /* Wait 50msec to make sure we have full link enabled */
init_ohci1394_initialize(ohci);
/*
* The initialization causes at least one IEEE1394 bus reset. Enabling
* physical DMA only works *after* *all* bus resets have calmed down:
*/
init_ohci1394_wait_for_busresets(ohci);
/* We had to wait and do this now if we want to debug early problems */
init_ohci1394_enable_physical_dma(ohci);
}
/**
* init_ohci1394_controller - Map the registers of the controller and init DMA
* This maps the registers of the specified controller and initializes it
*/
static inline void __init init_ohci1394_controller(int num, int slot, int func)
{
unsigned long ohci_base;
struct ti_ohci ohci;
printk(KERN_INFO "init_ohci1394_dma: initializing OHCI-1394"
" at %02x:%02x.%x\n", num, slot, func);
ohci_base = read_pci_config(num, slot, func, PCI_BASE_ADDRESS_0+(0<<2))
& PCI_BASE_ADDRESS_MEM_MASK;
set_fixmap_nocache(FIX_OHCI1394_BASE, ohci_base);
ohci.registers = (void *)fix_to_virt(FIX_OHCI1394_BASE);
init_ohci1394_reset_and_init_dma(&ohci);
}
/**
* debug_init_ohci1394_dma - scan for OHCI1394 controllers and init DMA on them
* Scans the whole PCI space for OHCI1394 controllers and inits DMA on them
*/
void __init init_ohci1394_dma_on_all_controllers(void)
{
int num, slot, func;
if (!early_pci_allowed())
return;
/* Poor man's PCI discovery, the only thing we can do at early boot */
for (num = 0; num < 32; num++) {
for (slot = 0; slot < 32; slot++) {
for (func = 0; func < 8; func++) {
u32 class = read_pci_config(num,slot,func,
PCI_CLASS_REVISION);
if ((class == 0xffffffff))
continue; /* No device at this func */
if (class>>8 != PCI_CLASS_SERIAL_FIREWIRE_OHCI)
continue; /* Not an OHCI-1394 device */
init_ohci1394_controller(num, slot, func);
break; /* Assume one controller per device */
}
}
}
printk(KERN_INFO "init_ohci1394_dma: finished initializing OHCI DMA\n");
}
/**
* setup_init_ohci1394_early - enables early OHCI1394 DMA initialization
*/
static int __init setup_ohci1394_dma(char *opt)
{
if (!strcmp(opt, "early"))
init_ohci1394_dma_early = 1;
return 0;
}
/* passing ohci1394_dma=early on boot causes early OHCI1394 DMA initialization */
early_param("ohci1394_dma", setup_ohci1394_dma);
