/*
* Setup pointers to hardware-dependent routines.
*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*
* Copyright (C) 1996, 97, 98, 2000, 03, 04, 06 Ralf Baechle (ralf@linux-mips.org)
*/
#include <linux/eisa.h>
#include <linux/hdreg.h>
#include <linux/ioport.h>
#include <linux/sched.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/mc146818rtc.h>
#include <linux/pm.h>
#include <linux/pci.h>
#include <linux/console.h>
#include <linux/fb.h>
#include <linux/tty.h>
#ifdef CONFIG_ARC
#include <asm/arc/types.h>
#include <asm/sgialib.h>
#endif
#include <asm/bcache.h>
#include <asm/bootinfo.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mc146818-time.h>
#include <asm/processor.h>
#include <asm/ptrace.h>
#include <asm/reboot.h>
#include <asm/sni.h>
#include <asm/time.h>
#include <asm/traps.h>
extern void sni_machine_restart(char *command);
extern void sni_machine_halt(void);
extern void sni_machine_power_off(void);
static void __init sni_rm200_pci_timer_setup(struct irqaction *irq)
{
/* set the clock to 100 Hz */
outb_p(0x34,0x43); /* binary, mode 2, LSB/MSB, ch 0 */
outb_p(LATCH & 0xff , 0x40); /* LSB */
outb(LATCH >> 8 , 0x40); /* MSB */
setup_irq(0, irq);
}
/*
* A bit more gossip about the iron we're running on ...
*/
static inline void sni_pcimt_detect(void)
{
char boardtype[80];
unsigned char csmsr;
char *p = boardtype;
unsigned int asic;
csmsr = *(volatile unsigned char *)PCIMT_CSMSR;
p += sprintf(p, "%s PCI", (csmsr & 0x80) ? "RM200" : "RM300");
if ((csmsr & 0x80) == 0)
p += sprintf(p, ", board revision %s",
(csmsr & 0x20) ? "D" : "C");
asic = csmsr & 0x80;
asic = (csmsr & 0x08) ? asic : !asic;
p += sprintf(p, ", ASIC PCI Rev %s", asic ? "1.0" : "1.1");
printk("%s.\n", boardtype);
}
static void __init sni_display_setup(void)
{
#if defined(CONFIG_VT) && defined(CONFIG_VGA_CONSOLE) && defined(CONFIG_ARC)
struct screen_info *si = &screen_info;
DISPLAY_STATUS *di;
di = ArcGetDisplayStatus(1);
if (di) {
si->orig_x = di->CursorXPosition;
si->orig_y = di->CursorYPosition;
si->orig_video_cols = di->CursorMaxXPosition;
si->orig_video_lines = di->CursorMaxYPosition;
si->orig_video_isVGA = VIDEO_TYPE_VGAC;
si->orig_video_points = 16;
}
#endif
}
static struct resource sni_io_resource = {
.start = 0x00001000UL,
.end = 0x03bfffffUL,
.name = "PCIMT IO MEM",
.flags = IORESOURCE_IO,
};
static struct resource pcimt_io_resources[] = {
{
.start = 0x00,
.end = 0x1f,
.name = "dma1",
.flags = IORESOURCE_BUSY
}, {
.start = 0x40,
.end = 0x5f,
.name = "timer",
.flags = IORESOURCE_BUSY
}, {
.start = 0x60,
.end = 0x6f,
.name = "keyboard",
.flags = IORESOURCE_BUSY
}, {
.start = 0x80,
.end = 0x8f,
.name = "dma page reg",
.flags = IORESOURCE_BUSY
}, {
.start = 0xc0,
.end = 0xdf,
.name = "dma2",
.flags = IORESOURCE_BUSY
}, {
.start = 0xcfc,
.end = 0xcff,
.name = "PCI config data",
.flags = IORESOURCE_BUSY
}
};
static struct resource sni_mem_resource = {
.start = 0x10000000UL,
.end = 0xffffffffUL,
.name = "PCIMT PCI MEM",
.flags = IORESOURCE_MEM
};
/*
* The RM200/RM300 has a few holes in it's PCI/EISA memory address space used
* for other purposes. Be paranoid and allocate all of the before the PCI
* code gets a chance to to map anything else there ...
*
* This leaves the following areas available:
*
* 0x10000000 - 0x1009ffff (640kB) PCI/EISA/ISA Bus Memory
* 0x10100000 - 0x13ffffff ( 15MB) PCI/EISA/ISA Bus Memory
* 0x18000000 - 0x1fbfffff (124MB) PCI/EISA Bus Memory
* 0x1ff08000 - 0x1ffeffff (816kB) PCI/EISA Bus Memory
* 0xa0000000 - 0xffffffff (1.5GB) PCI/EISA Bus Memory
*/
static struct resource pcimt_mem_resources[] = {
{
.start = 0x100a0000,
.end = 0x100bffff,
.name = "Video RAM area",
.flags = IORESOURCE_BUSY
}, {
.start = 0x100c0000,
.end = 0x100fffff,
.name = "ISA Reserved",
.flags = IORESOURCE_BUSY
}, {
.start = 0x14000000,
.end = 0x17bfffff,
.name = "PCI IO",
.flags = IORESOURCE_BUSY
}, {
.start = 0x17c00000,
.end = 0x17ffffff,
.name = "Cache Replacement Area",
.flags = IORESOURCE_BUSY
}, {
.start = 0x1a000000,
.end = 0x1a000003,
.name = "PCI INT Acknowledge",
.flags = IORESOURCE_BUSY
}, {
.start = 0x1fc00000,
.end = 0x1fc7ffff,
.name = "Boot PROM",
.flags = IORESOURCE_BUSY
}, {
.start = 0x1fc80000,
.end = 0x1fcfffff,
.name = "Diag PROM",
.flags = IORESOURCE_BUSY
}, {
.start = 0x1fd00000,
.end = 0x1fdfffff,
.name = "X-Bus",
.flags = IORESOURCE_BUSY
}, {
.start = 0x1fe00000,
.end = 0x1fefffff,
.name = "BIOS map",
.flags = IORESOURCE_BUSY
}, {
.start = 0x1ff00000,
.end = 0x1ff7ffff,
.name = "NVRAM / EEPROM",
.flags = IORESOURCE_BUSY
}, {
.start = 0x1fff0000,
.end = 0x1fffefff,
.name = "ASIC PCI",
.flags = IORESOURCE_BUSY
}, {
.start = 0x1ffff000,
.end = 0x1fffffff,
.name = "MP Agent",
.flags = IORESOURCE_BUSY
}, {
.start = 0x20000000,
.end = 0x9fffffff,
.name = "Main Memory",
.flags = IORESOURCE_BUSY
}
};
static void __init sni_resource_init(void)
{
int i;
/* request I/O space for devices used on all i[345]86 PCs */
for (i = 0; i < ARRAY_SIZE(pcimt_io_resources); i++)
request_resource(&ioport_resource, pcimt_io_resources + i);
/* request mem space for pcimt-specific devices */
for (i = 0; i < ARRAY_SIZE(pcimt_mem_resources); i++)
request_resource(&sni_mem_resource, pcimt_mem_resources + i);
ioport_resource.end = sni_io_resource.end;
}
extern struct pci_ops sni_pci_ops;
static struct pci_controller sni_controller = {
.pci_ops = &sni_pci_ops,
.mem_resource = &sni_mem_resource,
.mem_offset = 0x10000000UL,
.io_resource = &sni_io_resource,
.io_offset = 0x00000000UL
};
static inline void sni_pcimt_time_init(void)
{
rtc_mips_get_time = mc146818_get_cmos_time;
rtc_mips_set_time = mc146818_set_rtc_mmss;
}
void __init plat_mem_setup(void)
{
sni_pcimt_detect();
sni_pcimt_sc_init();
sni_pcimt_time_init();
set_io_port_base(SNI_PORT_BASE);
ioport_resource.end = sni_io_resource.end;
/*
* Setup (E)ISA I/O memory access stuff
*/
isa_slot_offset = 0xb0000000;
#ifdef CONFIG_EISA
EISA_bus = 1;
#endif
sni_resource_init();
board_timer_setup = sni_rm200_pci_timer_setup;
_machine_restart = sni_machine_restart;
_machine_halt = sni_machine_halt;
pm_power_off = sni_machine_power_off;
sni_display_setup();
#ifdef CONFIG_PCI
register_pci_controller(&sni_controller);
#endif
}
