/*
* omap-pm.h - OMAP power management interface
*
* Copyright (C) 2008-2010 Texas Instruments, Inc.
* Copyright (C) 2008-2010 Nokia Corporation
* Paul Walmsley
*
* Interface developed by (in alphabetical order): Karthik Dasu, Jouni
* Högander, Tony Lindgren, Rajendra Nayak, Sakari Poussa,
* Veeramanikandan Raju, Anand Sawant, Igor Stoppa, Paul Walmsley,
* Richard Woodruff
*/
#ifndef ASM_ARM_ARCH_OMAP_OMAP_PM_H
#define ASM_ARM_ARCH_OMAP_OMAP_PM_H
#include <linux/device.h>
#include <linux/cpufreq.h>
#include <linux/clk.h>
#include <linux/pm_opp.h>
/*
* agent_id values for use with omap_pm_set_min_bus_tput():
*
* OCP_INITIATOR_AGENT is only valid for devices that can act as
* initiators -- it represents the device's L3 interconnect
* connection. OCP_TARGET_AGENT represents the device's L4
* interconnect connection.
*/
#define OCP_TARGET_AGENT 1
#define OCP_INITIATOR_AGENT 2
/**
* omap_pm_if_early_init - OMAP PM init code called before clock fw init
* @mpu_opp_table: array ptr to struct omap_opp for MPU
* @dsp_opp_table: array ptr to struct omap_opp for DSP
* @l3_opp_table : array ptr to struct omap_opp for CORE
*
* Initialize anything that must be configured before the clock
* framework starts. The "_if_" is to avoid name collisions with the
* PM idle-loop code.
*/
int __init omap_pm_if_early_init(void);
/**
* omap_pm_if_init - OMAP PM init code called after clock fw init
*
* The main initialization code. OPP tables are passed in here. The
* "_if_" is to avoid name collisions with the PM idle-loop code.
*/
int __init omap_pm_if_init(void);
/*
* Device-driver-originated constraints (via board-*.c files, platform_data)
*/
/**
* omap_pm_set_max_mpu_wakeup_lat - set the maximum MPU wakeup latency
* @dev: struct device * requesting the constraint
* @t: maximum MPU wakeup latency in microseconds
*
* Request that the maximum interrupt latency for the MPU to be no
* greater than @t microseconds. "Interrupt latency" in this case is
* defined as the elapsed time from the occurrence of a hardware or
* timer interrupt to the time when the device driver's interrupt
* service routine has been entered by the MPU.
*
* It is intended that underlying PM code will use this information to
* determine what power state to put the MPU powerdomain into, and
* possibly the CORE powerdomain as well, since interrupt handling
* code currently runs from SDRAM. Advanced PM or board*.c code may
* also configure interrupt controller priorities, OCP bus priorities,
* CPU speed(s), etc.
*
* This function will not affect device wakeup latency, e.g., time
* elapsed from when a device driver enables a hardware device with
* clk_enable(), to when the device is ready for register access or
* other use. To control this device wakeup latency, use
* omap_pm_set_max_dev_wakeup_lat()
*
* Multiple calls to omap_pm_set_max_mpu_wakeup_lat() will replace the
* previous t value. To remove the latency target for the MPU, call
* with t = -1.
*
* XXX This constraint will be deprecated soon in favor of the more
* general omap_pm_set_max_dev_wakeup_lat()
*
* Returns -EINVAL for an invalid argument, -ERANGE if the constraint
* is not satisfiable, or 0 upon success.
*/
int omap_pm_set_max_mpu_wakeup_lat(struct device *dev, long t);
/**
* omap_pm_set_min_bus_tput - set minimum bus throughput needed by device
* @dev: struct device * requesting the constraint
* @tbus_id: interconnect to operate on (OCP_{INITIATOR,TARGET}_AGENT)
* @r: minimum throughput (in KiB/s)
*
* Request that the minimum data throughput on the OCP interconnect
* attached to device @dev interconnect agent @tbus_id be no less
* than @r KiB/s.
*
* It is expected that the OMAP PM or bus code will use this
* information to set the interconnect clock to run at the lowest
* possible speed that satisfies all current system users. The PM or
* bus code will adjust the estimate based on its model of the bus, so
* device driver authors should attempt to specify an accurate
* quantity for their device use case, and let the PM or bus code
* overestimate the numbers as necessary to handle request/response
* latency, other competing users on the system, etc. On OMAP2/3, if
* a driver requests a minimum L4 interconnect speed constraint, the
* code will also need to add an minimum L3 interconnect speed
* constraint,
*
* Multiple calls to omap_pm_set_min_bus_tput() will replace the
* previous rate value for this device. To remove the interconnect
* throughput restriction for this device, call with r = 0.
*
* Returns -EINVAL for an invalid argument, -ERANGE if the constraint
* is not satisfiable, or 0 upon success.
*/
int omap_pm_set_min_bus_tput(struct device *dev, u8 agent_id, unsigned long r);
/*
* CPUFreq-originated constraint
*
* In the future, this should be handled by custom OPP clocktype
* functions.
*/
/*
* Device context loss tracking
*/
/**
* omap_pm_get_dev_context_loss_count - return count of times dev has lost ctx
* @dev: struct device *
*
* This function returns the number of times that the device @dev has
* lost its internal context. This generally occurs on a powerdomain
* transition to OFF. Drivers use this as an optimization to avoid restoring
* context if the device hasn't lost it. To use, drivers should initially
* call this in their context save functions and store the result. Early in
* the driver's context restore function, the driver should call this function
* again, and compare the result to the stored counter. If they differ, the
* driver must restore device context. If the number of context losses
* exceeds the maximum positive integer, the function will wrap to 0 and
* continue counting. Returns the number of context losses for this device,
* or negative value upon error.
*/
int omap_pm_get_dev_context_loss_count(struct device *dev);
void omap_pm_enable_off_mode(void);
void omap_pm_disable_off_mode(void);
#endif
