/*
* Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include "omap5.dtsi"
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
aliases {
display0 = &hdmi0;
};
vmmcsd_fixed: fixedregulator-mmcsd {
compatible = "regulator-fixed";
regulator-name = "vmmcsd_fixed";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
};
mmc3_pwrseq: sdhci0_pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&clk32kgaudio>;
clock-names = "ext_clock";
};
vmmcsdio_fixed: fixedregulator-mmcsdio {
compatible = "regulator-fixed";
regulator-name = "vmmcsdio_fixed";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>; /* gpio140 WLAN_EN */
enable-active-high;
startup-delay-us = <70000>;
pinctrl-names = "default";
pinctrl-0 = <&wlan_pins>;
};
/* HS USB Host PHY on PORT 2 */
hsusb2_phy: hsusb2_phy {
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
clocks = <&auxclk1_ck>;
clock-names = "main_clk";
clock-frequency = <19200000>;
};
/* HS USB Host PHY on PORT 3 */
hsusb3_phy: hsusb3_phy {
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
};
leds {
compatible = "gpio-leds";
led@1 {
label = "omap5:blue:usr1";
gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */
linux,default-trigger = "heartbeat";
default-state = "off";
};
};
tpd12s015: encoder@0 {
compatible = "ti,tpd12s015";
pinctrl-names = "default";
pinctrl-0 = <&tpd12s015_pins>;
/* gpios defined in the board specific dts */
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
tpd12s015_in: endpoint@0 {
remote-endpoint = <&hdmi_out>;
};
};
port@1 {
reg = <1>;
tpd12s015_out: endpoint@0 {
remote-endpoint = <&hdmi_connector_in>;
};
};
};
};
hdmi0: connector@0 {
compatible = "hdmi-connector";
label = "hdmi";
type = "b";
port {
hdmi_connector_in: endpoint {
remote-endpoint = <&tpd12s015_out>;
};
};
};
sound: sound {
compatible = "ti,abe-twl6040";
ti,model = "omap5-uevm";
ti,mclk-freq = <19200000>;
ti,mcpdm = <&mcpdm>;
ti,twl6040 = <&twl6040>;
/* Audio routing */
ti,audio-routing =
"Headset Stereophone", "HSOL",
"Headset Stereophone", "HSOR",
"Line Out", "AUXL",
"Line Out", "AUXR",
"HSMIC", "Headset Mic",
"Headset Mic", "Headset Mic Bias",
"AFML", "Line In",
"AFMR", "Line In";
};
};
&gpio8 {
/* TI trees use GPIO instead of msecure, see also muxing */
p234 {
gpio-hog;
gpios = <10 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "gpio8_234/msecure";
};
};
&omap5_pmx_core {
pinctrl-names = "default";
pinctrl-0 = <
&usbhost_pins
&led_gpio_pins
>;
twl6040_pins: pinmux_twl6040_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */
>;
};
mcpdm_pins: pinmux_mcpdm_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x182, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
OMAP5_IOPAD(0x19c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */
OMAP5_IOPAD(0x19e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */
OMAP5_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */
OMAP5_IOPAD(0x1a2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */
>;
};
mcbsp1_pins: pinmux_mcbsp1_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x18c, PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */
OMAP5_IOPAD(0x18e, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */
OMAP5_IOPAD(0x190, PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */
OMAP5_IOPAD(0x192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */
>;
};
mcbsp2_pins: pinmux_mcbsp2_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x194, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */
OMAP5_IOPAD(0x196, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */
OMAP5_IOPAD(0x198, PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */
OMAP5_IOPAD(0x19a, PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */
>;
};
i2c1_pins: pinmux_i2c1_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x1f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
OMAP5_IOPAD(0x1f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
>;
};
mcspi2_pins: pinmux_mcspi2_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
OMAP5_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
OMAP5_IOPAD(0x100, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */
OMAP5_IOPAD(0x102, PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */
>;
};
mcspi3_pins: pinmux_mcspi3_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x0b8, PIN_INPUT | MUX_MODE1) /* mcspi3_somi */
OMAP5_IOPAD(0x0ba, PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */
OMAP5_IOPAD(0x0bc, PIN_INPUT | MUX_MODE1) /* mcspi3_simo */
OMAP5_IOPAD(0x0be, PIN_INPUT | MUX_MODE1) /* mcspi3_clk */
>;
};
mmc3_pins: pinmux_mmc3_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
>;
};
wlan_pins: pinmux_wlan_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */
>;
};
/* TI trees use GPIO mode; msecure mode does not work reliably? */
palmas_msecure_pins: palmas_msecure_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x180, PIN_OUTPUT | MUX_MODE6) /* gpio8_234 */
>;
};
usbhost_pins: pinmux_usbhost_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x0c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
OMAP5_IOPAD(0x0c6, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
OMAP5_IOPAD(0x1de, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
OMAP5_IOPAD(0x1e0, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
OMAP5_IOPAD(0x0b0, PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */
OMAP5_IOPAD(0x0ae, PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */
>;
};
led_gpio_pins: pinmux_led_gpio_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x1d6, PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */
>;
};
uart1_pins: pinmux_uart1_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x0a0, PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */
OMAP5_IOPAD(0x0a2, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */
OMAP5_IOPAD(0x0a4, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */
OMAP5_IOPAD(0x0a6, PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */
>;
};
uart3_pins: pinmux_uart3_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x1da, PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */
OMAP5_IOPAD(0x1dc, PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */
>;
};
uart5_pins: pinmux_uart5_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x1b0, PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */
OMAP5_IOPAD(0x1b2, PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */
OMAP5_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */
OMAP5_IOPAD(0x1b6, PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */
>;
};
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
OMAP5_IOPAD(0x140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */
OMAP5_IOPAD(0x142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */
>;
};
tpd12s015_pins: pinmux_tpd12s015_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x13e, PIN_INPUT_PULLDOWN | MUX_MODE6) /* hdmi_hpd.gpio7_193 */
>;
};
};
&omap5_pmx_wkup {
pinctrl-names = "default";
pinctrl-0 = <
&usbhost_wkup_pins
>;
palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1 */
>;
};
usbhost_wkup_pins: pinmux_usbhost_wkup_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
>;
};
wlcore_irq_pin: pinmux_wlcore_irq_pin {
pinctrl-single,pins = <
OMAP5_IOPAD(0x40, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */
>;
};
};
&mmc1 {
vmmc-supply = <&ldo9_reg>;
bus-width = <4>;
};
&mmc2 {
vmmc-supply = <&vmmcsd_fixed>;
bus-width = <8>;
ti,non-removable;
};
&mmc3 {
vmmc-supply = <&vmmcsdio_fixed>;
mmc-pwrseq = <&mmc3_pwrseq>;
bus-width = <4>;
non-removable;
cap-power-off-card;
pinctrl-names = "default";
pinctrl-0 = <&mmc3_pins &wlcore_irq_pin>;
interrupts-extended = <&gic GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
&omap5_pmx_core 0x168>;
#address-cells = <1>;
#size-cells = <0>;
wlcore: wlcore@2 {
compatible = "ti,wl1271";
reg = <2>;
interrupt-parent = <&gpio1>;
interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; /* gpio 14 */
ref-clock-frequency = <26000000>;
};
};
&mmc4 {
status = "disabled";
};
&mmc5 {
status = "disabled";
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
clock-frequency = <400000>;
palmas: palmas@48 {
compatible = "ti,palmas";
interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
reg = <0x48>;
interrupt-controller;
#interrupt-cells = <2>;
ti,system-power-controller;
pinctrl-names = "default";
pinctrl-0 = <&palmas_sys_nirq_pins &palmas_msecure_pins>;
extcon_usb3: palmas_usb {
compatible = "ti,palmas-usb-vid";
ti,enable-vbus-detection;
ti,enable-id-detection;
ti,wakeup;
};
clk32kgaudio: palmas_clk32k@1 {
compatible = "ti,palmas-clk32kgaudio";
#clock-cells = <0>;
};
rtc {
compatible = "ti,palmas-rtc";
interrupt-parent = <&palmas>;
interrupts = <8 IRQ_TYPE_NONE>;
ti,backup-battery-chargeable;
ti,backup-battery-charge-high-current;
};
palmas_pmic {
compatible = "ti,palmas-pmic";
interrupt-parent = <&palmas>;
interrupts = <14 IRQ_TYPE_NONE>;
interrupt-names = "short-irq";
ti,ldo6-vibrator;
regulators {
smps123_reg: smps123 {
/* VDD_OPP_MPU */
regulator-name = "smps123";
regulator-min-microvolt = < 600000>;
regulator-max-microvolt = <1500000>;
regulator-always-on;
regulator-boot-on;
};
smps45_reg: smps45 {
/* VDD_OPP_MM */
regulator-name = "smps45";
regulator-min-microvolt = < 600000>;
regulator-max-microvolt = <1310000>;
regulator-always-on;
regulator-boot-on;
};
smps6_reg: smps6 {
/* VDD_DDR3 - over VDD_SMPS6 */
regulator-name = "smps6";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
regulator-boot-on;
};
smps7_reg: smps7 {
/* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
regulator-name = "smps7";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
smps8_reg: smps8 {
/* VDD_OPP_CORE */
regulator-name = "smps8";
regulator-min-microvolt = < 600000>;
regulator-max-microvolt = <1310000>;
regulator-always-on;
regulator-boot-on;
};
smps9_reg: smps9 {
/* VDDA_2v1_AUD over VDD_2v1 */
regulator-name = "smps9";
regulator-min-microvolt = <2100000>;
regulator-max-microvolt = <2100000>;
ti,smps-range = <0x80>;
};
smps10_out2_reg: smps10_out2 {
/* VBUS_5V_OTG */
regulator-name = "smps10_out2";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
regulator-boot-on;
};
smps10_out1_reg: smps10_out1 {
/* VBUS_5V_OTG */
regulator-name = "smps10_out1";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
ldo1_reg: ldo1 {
/* VDDAPHY_CAM: vdda_csiport */
regulator-name = "ldo1";
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1800000>;
};
ldo2_reg: ldo2 {
/* VCC_2V8_DISP: Does not go anywhere */
regulator-name = "ldo2";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
/* Unused */
status = "disabled";
};
ldo3_reg: ldo3 {
/* VDDAPHY_MDM: vdda_lli */
regulator-name = "ldo3";
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-boot-on;
/* Only if Modem is used */
status = "disabled";
};
ldo4_reg: ldo4 {
/* VDDAPHY_DISP: vdda_dsiport/hdmi */
regulator-name = "ldo4";
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1800000>;
};
ldo5_reg: ldo5 {
/* VDDA_1V8_PHY: usb/sata/hdmi.. */
regulator-name = "ldo5";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
ldo6_reg: ldo6 {
/* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
regulator-name = "ldo6";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
regulator-boot-on;
};
ldo7_reg: ldo7 {
/* VDD_VPP: vpp1 */
regulator-name = "ldo7";
regulator-min-microvolt = <2000000>;
regulator-max-microvolt = <2000000>;
/* Only for efuse reprograming! */
status = "disabled";
};
ldo8_reg: ldo8 {
/* VDD_3v0: Does not go anywhere */
regulator-name = "ldo8";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-boot-on;
/* Unused */
status = "disabled";
};
ldo9_reg: ldo9 {
/* VCC_DV_SDIO: vdds_sdcard */
regulator-name = "ldo9";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3000000>;
regulator-boot-on;
};
ldoln_reg: ldoln {
/* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
regulator-name = "ldoln";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
ldousb_reg: ldousb {
/* VDDA_3V_USB: VDDA_USBHS33 */
regulator-name = "ldousb";
regulator-min-microvolt = <3250000>;
regulator-max-microvolt = <3250000>;
regulator-always-on;
regulator-boot-on;
};
regen3_reg: regen3 {
/* REGEN3 controls LDO9 supply to card */
regulator-name = "regen3";
regulator-always-on;
regulator-boot-on;
};
};
};
palmas_power_button: palmas_power_button {
compatible = "ti,palmas-pwrbutton";
interrupt-parent = <&palmas>;
interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
wakeup-source;
};
};
twl6040: twl@4b {
compatible = "ti,twl6040";
reg = <0x4b>;
pinctrl-names = "default";
pinctrl-0 = <&twl6040_pins>;
interrupts = <GIC_SPI 119 IRQ_TYPE_NONE>; /* IRQ_SYS_2N cascaded to gic */
ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>; /* gpio line 141 */
vio-supply = <&smps7_reg>;
v2v1-supply = <&smps9_reg>;
enable-active-high;
clocks = <&clk32kgaudio>;
clock-names = "clk32k";
};
};
&mcpdm {
pinctrl-names = "default";
pinctrl-0 = <&mcpdm_pins>;
status = "okay";
};
&mcbsp1 {
pinctrl-names = "default";
pinctrl-0 = <&mcbsp1_pins>;
status = "okay";
};
&mcbsp2 {
pinctrl-names = "default";
pinctrl-0 = <&mcbsp2_pins>;
status = "okay";
};
&usbhshost {
port2-mode = "ehci-hsic";
port3-mode = "ehci-hsic";
};
&usbhsehci {
phys = <0 &hsusb2_phy &hsusb3_phy>;
};
&usb3 {
extcon = <&extcon_usb3>;
vbus-supply = <&smps10_out1_reg>;
};
&mcspi1 {
};
&mcspi2 {
pinctrl-names = "default";
pinctrl-0 = <&mcspi2_pins>;
};
&mcspi3 {
pinctrl-names = "default";
pinctrl-0 = <&mcspi3_pins>;
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>;
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
<&omap5_pmx_core 0x19c>;
};
&uart5 {
pinctrl-names = "default";
pinctrl-0 = <&uart5_pins>;
};
&cpu0 {
cpu0-supply = <&smps123_reg>;
};
&dss {
status = "ok";
};
&hdmi {
status = "ok";
/* vdda-supply populated in board specific dts file */
pinctrl-names = "default";
pinctrl-0 = <&dss_hdmi_pins>;
port {
hdmi_out: endpoint {
remote-endpoint = <&tpd12s015_in>;
};
};
};
