| Age | Commit message (Collapse) | Author |
|---|
|
rmi_f54_work() reads a diagnostics report from the device into
f54->report_data, sizing the transfer with rmi_f54_get_report_size():
report_size = rmi_f54_get_report_size(f54);
...
for (i = 0; i < report_size; i += F54_REPORT_DATA_SIZE) {
int size = min(F54_REPORT_DATA_SIZE, report_size - i);
...
rmi_read_block(.., f54->report_data + i, size);
}
report_data is allocated once at probe from F54's own electrode counts
(array3_size(f54->num_tx_electrodes, f54->num_rx_electrodes, sizeof(u16))),
but rmi_f54_get_report_size() computes the size from
drv_data->num_*_electrodes when those are set, i.e. from the F55
function's electrode counts. Both counts come straight from device
queries (F54 and F55 each report up to 255 electrodes) and nothing
constrains the F55 counts to the F54 ones.
A malicious or malfunctioning RMI4 device that reports larger F55
electrode counts than its F54 counts makes report_size exceed the
allocation, so the read loop writes past report_data (and the V4L2
dequeue memcpy() then reads past it). On conforming hardware the F55
configured electrodes are a subset of the F54 physical electrodes, so
report_size never exceeds the buffer and well-behaved devices are
unaffected.
Record the allocation size and reject a report that does not fit,
mirroring the existing zero-size check.
Fixes: c762cc68b6a1 ("Input: synaptics-rmi4 - propagate correct number of rx and tx electrodes to F54")
Cc: stable@vger.kernel.org
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Assisted-by: Antigravity:gemini-3.5-flash
Link: https://patch.msgid.link/20260626051802.4033172-3-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In rmi_f54_work(), if an error occurs during report request or command
verification, the code jumped directly to the 'error' label, bypassing
the 'abort' label where f54->report_size was normally zeroed out.
This left f54->report_size containing its previous successful payload
size. If a user then altered the V4L2 format to a smaller size, and a
subsequent run failed, rmi_f54_buffer_queue() would copy the stale,
larger payload size into the shrunken V4L2 buffer, causing a heap
buffer overflow.
Fix this by merging the 'abort' and 'error' labels into a single 'out'
exit path, and ensuring that f54->report_size is always set to 0 on
failure by checking for error and zeroing the local report_size first.
Fixes: 3a762dbd5347 ("[media] Input: synaptics-rmi4 - add support for F54 diagnostics")
Cc: stable@vger.kernel.org
Reported-by: sashiko-bot@kernel.org
Assisted-by: Antigravity:gemini-3.5-flash
Link: https://patch.msgid.link/20260626051802.4033172-2-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
During F55 sensor detection, the transmitter (TX) electrode count was
incorrectly assigned the value of the receiver (RX) electrode count
due to copy-paste typos.
This incorrect value was then propagated to the driver data and used
by F54 to determine the diagnostics report size. On devices with more
RX than TX electrodes, this inflated the perceived TX count, leading
to incorrect report size calculations and potential out-of-bounds
buffer accesses.
Fix the typos by correctly assigning the TX electrode counts.
Fixes: 6adba43fd222 ("Input: synaptics-rmi4 - add support for F55 sensor tuning")
Fixes: c762cc68b6a1 ("Input: synaptics-rmi4 - propagate correct number of rx and tx electrodes to F54")
Reported-by: sashiko-bot@kernel.org
Cc: stable@vger.kernel.org
Assisted-by: Antigravity:gemini-3.5-flash
Link: https://patch.msgid.link/20260626051802.4033172-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
focaltech_finger_state stores finger coordinates x and y as unsigned
int. When processing relative packets, negative deltas can cause
unsigned integer underflow if the finger moves past the left or bottom
boundary of the touchpad, wrapping the coordinates to values near
UINT_MAX.
When clamping the coordinates in focaltech_report_state(), these
underflowed values are clamped against priv->x_max / priv->y_max instead
of 0, causing the cursor to jump erratically to the opposite edge of the
touchpad.
Change the coordinate variables and limits to signed int so that
negative values resulting from relative movements clamp correctly to 0,
and write the clamped values back to state in focaltech_report_state()
to prevent coordinate wind-up accumulation at the touchpad boundaries.
Fixes: 05be1d079ec0 ("Input: psmouse - support for the FocalTech PS/2 protocol extensions")
Reported-by: sashiko-bot@kernel.org
Link: https://patch.msgid.link/am_tH_F938rK6ask@google.com
Assisted-by: Antigravity:gemini-3.6-flash
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The driver allocates max_touch_num input slots, which are indexed from
zero through max_touch_num - 1. The current check allows a finger ID
equal to max_touch_num to reach cst3xx_report_contact(). While the input
core ignores out-of-range slot indices, reporting touch data without a
valid slot change corrupts the touch state of the previously active slot.
The touch count is read from the controller's report and is used to
index the fixed-size report buffer without first checking its range.
Reject counts larger than the supported number of touch slots before
checking the trailing byte or parsing touch data.
Reject finger IDs equal to or greater than max_touch_num, and return
immediately when an invalid finger ID is encountered so that corrupt
touch frames are discarded instead of reporting partial contact state.
The V821 Avaota F1 board configures the vendor driver with one touch
slot, so finger ID 1 is already invalid on that device.
Fixes: 66603243f528 ("Input: add driver for Hynitron cstxxx touchscreens")
Signed-off-by: Jianing Li <m13940358460@163.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260804031339.2379-1-m13940358460@163.com
Assisted-by: Antigravity:gemini-3.6-flash
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In evdev_pass_values(), the input_event structure is allocated on the
kernel stack and populated field-by-field. However, it is never fully
initialized. On architectures where struct input_event contains explicit
or implicit padding (such as the 32-bit __pad field on SPARC64), these
padding bytes are left uninitialized.
When this event structure is subsequently passed to the client buffer
and later copied to userspace, the uninitialized padding bytes leak
kernel stack memory, potentially exposing sensitive information.
Similar issues exist in __evdev_queue_syn_dropped and __pass_event.
Fix this by explicitly zeroing the entire event structure with memset()
before populating its fields. This ensures all padding bytes are cleared
before the data crosses the security boundary.
Reported-by: sashiko-bot@kernel.org
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/ampGGKo4UMKru6f5@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Replace manual serialization with guard(mutex) and guard(serio_pause_rx)
where appropriate. This eliminates the need for explicit goto-based error
paths.
Assisted-by: Antigravity:gemini-3.5-flash
Link: https://patch.msgid.link/20260727050803.1269941-4-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Rewrite psmouse_matches_pnp_id() to parse and match the space-separated
PNP ID string directly in place without dynamic memory allocation.
Assisted-by: Antigravity:gemini-3.5-flash
Link: https://patch.msgid.link/20260727050803.1269941-3-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In the past, psmouse_disconnect() used cancel_work_sync(). Because
cancel_work_sync() must be called with the psmouse_mutex dropped, and we
needed to prevent psmouse_receive_byte() from re-queueing the work
behind our back, the code transitioned the device to PSMOUSE_CMD_MODE
while holding the mutex, then dropped the mutex and cancelled the work.
When cancel_work_sync() was replaced with disable_work_sync() in this
path, the mutex juggling remained. However, disable_work_sync()
inherently prevents the work from being executed or re-queued, making
the mutex juggling unnecessary.
Clean this up by moving disable_work_sync() to the very top of
psmouse_disconnect(), before we acquire psmouse_mutex.
Assisted-by: Antigravity:gemini-3.5-flash
Link: https://patch.msgid.link/20260727050803.1269941-2-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When a PS/2 mouse is disconnected or unbound, psmouse_disconnect() calls
the protocol disconnect handler (psmouse->disconnect()). During this time,
stray bytes arriving from the physical controller can still be passed to
psmouse_handle_byte(), which will invoke psmouse->protocol_handler().
This creates an asynchronous race condition with vendor disconnect handlers
(such as synaptics_disconnect()), which free vendor-specific private
structures (psmouse->private). If a byte arrives while the structures
are being freed, it leads to a use-after-free or NULL pointer
dereference in the protocol handler.
Fix this by explicitly setting psmouse->protocol_handler to NULL
safely wrapped in scoped_guard(serio_pause_rx, serio) immediately before
calling the vendor disconnect handler. We also add an unlikely check
in psmouse_handle_byte() to safely drop incoming bytes if the protocol
handler is NULL.
Assisted-by: Antigravity:gemini-3.5-flash
Link: https://patch.msgid.link/20260727050803.1269941-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Simplify the driver by using the block-scope guard(pm_runtime_active)
instead of manually invoking pm_runtime_get_sync() and
pm_runtime_put().
Assisted-by: Antigravity:gemini-3.5-flash
Link: https://patch.msgid.link/20260713-samsung-kp-irq-v2-3-acc84b6daf9a@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The driver requests the interrupt during probe, which by default enables
it. If the bootloader left the keypad interrupts enabled, or if a
spurious interrupt fires early before the driver is fully initialized
and clocks are enabled, the interrupt handler will attempt to read
registers and may cause a synchronous external abort.
Fix this by requesting the interrupt with IRQF_NO_AUTOEN, keeping it
disabled during probe. Enable the interrupt in samsung_keypad_start()
when the device is opened and ready, and disable it in
samsung_keypad_stop() when the device is closed. Remove the redundant
re-enabling of the interrupt at the end of samsung_keypad_stop().
Additionally, manually clear the pending interrupt status during system
resume when the device is closed to avoid immediate resume.
Fixes: 0fffed27f92d ("Input: samsung-keypad - Add samsung keypad driver")
Assisted-by: Antigravity:gemini-3.1-pro
Link: https://patch.msgid.link/20260713-samsung-kp-irq-v2-2-acc84b6daf9a@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When checking if the device can wake the system, we should pull the
device_may_wakeup() check to the caller instead of repeating it inside
the toggle_wakeup() handler. Furthermore, when configuring the wakeup,
we should safely ensure we write to the registers in the correct order:
configure the interrupt receiver before enabling the peripheral's wake
functionality, and vice-versa.
Assisted-by: Antigravity:gemini-3.1-pro
Link: https://patch.msgid.link/20260713-samsung-kp-irq-v2-1-acc84b6daf9a@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Make finger2 (and also finger1) unsigned, so that if the finger index in
the packet is 0 then subtracting 1 creates an array index which overflows
above the existing check for FOC_MAX_FINGERS, as the existing comment says
it should, instead of writing to state->fingers[-1].
Fixes: 05be1d079ec0 ("Input: psmouse - support for the FocalTech PS/2 protocol extensions")
Signed-off-by: Richard Davies <richard@arachsys.com>
Link: https://patch.msgid.link/20260701190932.14960-1-richard@arachsys.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The internal keyboard on the HONOR ZQC-P (HONOR MagicBook Pro 14 2026)
does not work after boot.
Using the kernel command line 'i8042.dumbkbd=1' makes the keyboard
functional, but the CapsLock LED does not work. Adding the
'atkbd_deactivate_fixup' quirk fixes the keyboard and CapsLock LED
natively without requiring boot parameters.
DMI: HONOR ZQC-P/ZQC-P-PCB, BIOS 1.09 03/19/2026
Fixes: 9cf6e24c9fbf ("Input: atkbd - do not skip atkbd_deactivate() when skipping ATKBD_CMD_GETID")
Signed-off-by: Donglin Lyu <donglin_lyu@outlook.com>
Tested-by: Ruslan Shevchenko <adefka@gmail.com>
Link: https://patch.msgid.link/20260801151115.52709-1-donglin_lyu@outlook.com
Cc: stable@vger.kernel.org
[dtor: keep all HONOR entries together]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The internal keyboard of the Xiaomi Book Pro 14 does not work unless
atkbd skips deactivating it at the end of atkbd_probe().
Using 'i8042.dumbkbd=1' also makes the keyboard work, but then the driver
never writes to the keyboard at all, so the Caps Lock LED is lost. The
atkbd_deactivate_fixup quirk fixes both without a boot parameter.
DMI: XIAOMI Xiaomi Book Pro 14/TM2424, BIOS XMAPT4B0P0909 05/06/2026
Signed-off-by: Zhefu Zhang <a723356@gmail.com>
Reviewed-by: Andrew Zhou <zhoulol888@gmail.com>
Link: https://patch.msgid.link/20260802031559.19701-1-a723356@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground into gpio/for-next
gpio: legacy interface cleanups for 7.3
These are the remaining patches for legacy gpio interface
cleanup, ensuring that files referencing them are sure to
have CONFIG_GPIOLIB_LEGACY set, and use linux/gpio/legacy.h
instead of the old linux/gpio.h header.
There are a few more patches already merged in other
branches for 7.3, including soc, led, net and media. Once
everything is in, we can apply the final patches to turn
off CONFIG_GPIOLIB_LEGACY by default and remove the obsolete
header file.
This branch is based on the immutable ib-mfd-legacy-gpio-7.3
branch from mfd.git to avoid a conflict in the rohm drivers.
|
|
Replace printk(KERN_DEBUG) with dev_dbg() using the serio device,
which is the correct logging style for driver code. Also fix missing
space after comma in the function argument, and remove the redundant
'inexio.c:' filename prefix from the message.
Signed-off-by: Bivash Kumar Singh <bivashraj750@gmail.com>
Link: https://patch.msgid.link/20260725130803.6763-1-bivashraj750@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Fix two checkpatch warnings in elo_setup_10():
- Add missing space around '-' operator in array index expression
- Add missing 'const' qualifier to elo_types pointer array, since
the array is never modified after initialization
Signed-off-by: Bivash Kumar Singh <bivashraj750@gmail.com>
Link: https://patch.msgid.link/20260725113638.5147-1-bivashraj750@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
iforce_process_packet() reads fixed fields from joystick, wheel and
status packets without first checking their lengths. In particular, the
shared hats-and-buttons helper unconditionally reads data[6]. The status
tail is a sequence of 16-bit effect addresses, but an incomplete final
address is also consumed. A successful zero-length USB URB additionally
reads the packet ID before the common parser is called.
Reject the zero-length USB transfer, require the seven-byte joystick and
wheel prefixes and the two-byte status prefix, and consume only complete
status-tail addresses.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260720115018.75045-1-pengpeng@iscas.ac.cn
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
psxpad_spi_suspend() retrieves the controller state with
spi_get_drvdata(), but probe never stores it, so suspend dereferences a
NULL pointer. Store it during probe.
Fixes: 8be193c7b1f4 ("Input: add support for PlayStation 1/2 joypads connected via SPI")
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260721055551.1714965-1-lilinmao@kylinos.cn
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
charlieplex_keypad_scan_line() currently ignores the return value of
gpiod_direction_output() when setting the active output line for scanning.
If setting the GPIO direction fails (e.g. on I2C/SPI GPIO expanders or
hardware errors), the function continues to sleep and read input values
from an improperly configured GPIO line.
Fix this by capturing the return value of gpiod_direction_output() and
returning the error code immediately if it fails.
Fixes: 2ca45e57ea02 ("Input: charlieplex_keypad - add GPIO charlieplex keypad")
Signed-off-by: Surendra Singh Chouhan <kr494167@gmail.com>
Link: https://patch.msgid.link/20260723022943.9337-1-kr494167@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The firmware record parser checks that the record address starts within
the programmable map, but does not check that the complete record data
fits in that map. A record near the end of the map can therefore make
the copy to pmap exceed its destination span.
Check the record length against the remaining programmable map range
before copying the record data.
Fixes: 7b5bb55d0dad ("Input: add support for Azoteq IQS550/572/525")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260715083850.32155-1-pengpeng@iscas.ac.cn
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
cs40l50_add() copies the custom data of an FF_PERIODIC/FF_CUSTOM effect
straight from the ff_effect the user passed to EVIOCSFF, without
requiring it to hold anything:
work_data.custom_data = memdup_array_user(periodic->custom_data,
periodic->custom_len,
sizeof(s16));
work_data.custom_len = periodic->custom_len;
The driver then reads two words out of that buffer: custom_data[0] as the
waveform bank in cs40l50_effect_bank_set(), and custom_data[1] as the
index within the bank in cs40l50_effect_index_set(). Neither read is
covered by a length check, and custom_len is fully user controlled:
- custom_len == 0 makes memdup_array_user() call memdup_user() with a
length of zero, which returns ZERO_SIZE_PTR rather than an error, so
custom_data[0] dereferences it.
- custom_len == 1 allocates two bytes. A bank of ROM or RAM keeps
effect->type out of the OWT case, and custom_data[1] is then read one
word past the allocation.
The bank value itself is also mishandled. It is masked with
CS40L50_CUSTOM_DATA_MASK (0xffff) but stored in an s16, so a
custom_data[0] of 0x8000 or above wraps to a negative value that passes
the "bank_type >= CS40L50_WVFRM_BANK_NUM" test.
cs40l50_effect_index_set() indexes vib->dsp.banks[] with it before the
switch statement's default case gets a chance to reject it:
base_index = vib->dsp.banks[effect->type].base_index;
max_index = vib->dsp.banks[effect->type].max_index;
Require the two words the driver reads to be present, and hold the masked
bank in a u32 so the existing upper-bound test covers the whole range.
The da7280 haptic driver already range checks custom_len this way.
Fixes: c38fe1bb5d21 ("Input: cs40l50 - Add support for the CS40L50 haptic driver")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: HyeongJun An <sammiee5311@gmail.com>
Link: https://patch.msgid.link/20260718074032.1864861-1-sammiee5311@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
linux/gpio.h is going away, so remove that since the driver already
includes linux/gpio/consumer.h.
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Most users of gpio-keys and gpio-keys-polled use modern gpiolib
interfaces, but there are still number of ancient sh, arm32 and x86
machines that have never been converted.
Add an #ifdef block for the parts of the driver that are only used on
those legacy machines.
Link: https://lore.kernel.org/all/b3c94552-c104-42e3-be15-7e8362e8039e@gmail.com/
Link: https://lore.kernel.org/all/afJXG4_rtaj3l2Dk@google.com/
Link: https://lore.kernel.org/all/ajQ-CtU131FAJ9ES@google.com/
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # for input
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This driver converts information from ACPI in x86 based tablets and
laptops into platform_data for the gpio_keys driver, using the obsolete
gpio number based interfaces.
This should really be converted to some other method, but since the
conversion is nontrivial, have this one select GPIOLIB_LEGACY for the
time being.
This enables turning GPIOLIB_LEGACY off by default on most kernel
builds. Since the driver is only used on x86 portables, add a CONFIG_X86
dependency, which means non-x86 allmodconfig builds usuallly build
without the legacy gpio support.
Link: https://lore.kernel.org/all/ah-1z9LhVG0wtfBw@google.com/
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # for input
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add the VID/PID for the ZENAIM LEVERLESS controller to xpad_device and
the VID to xpad_table.
Signed-off-by: KADOTA, Kyohei <lufia@lufia.org>
Link: https://patch.msgid.link/CAFMepckDUuOHiDDVVhUYc-UqJMeCqrWSfCuxbJ2x2sGgdDD4nw@mail.gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The per-contact slot id is taken from the top nibble of the third
report byte, so it can be any value from 0 to 15. The driver only
allocates max_support_points MT slots (2 to 10 depending on the
variant), so a report that carries an id at or above that count - be it
a genuinely higher-numbered contact or a corrupted byte - is outside the
range the input core was told about.
input_mt_slot() silently ignores an ABS_MT_SLOT beyond num_slots and
leaves the current slot unchanged, so the following
input_mt_report_slot_state()/touchscreen_report_pos() pair is applied to
whichever slot happened to be selected last, reporting the contact at the
wrong position. Skip such entries instead.
Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
Link: https://patch.msgid.link/20260723-b4-ft5426-v2-1-cd2bed168051@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
byd_disconnect() uses timer_delete() before freeing the driver's private
data. This does not wait for a running byd_clear_touch() callback, which
dereferences the private data and its psmouse pointer. A callback racing
with disconnect can therefore access the private data after it has been
freed. The timer can also still be re-armed by byd_process_byte() while
the disconnect is in progress.
Use timer_shutdown_sync() before freeing the private data: it waits for
a running callback and turns any later re-arm attempt into a no-op.
Fixes: 2d5f5611dd0d ("Input: byd - enable absolute mode")
Cc: stable@vger.kernel.org
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Link: https://patch.msgid.link/20260720061259.1601281-1-lilinmao@kylinos.cn
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
suspend
The driver implements debounce protection using a timer-based mechanism:
when a key interrupt occurs, a timer is scheduled to verify the key state
after DEBOUNCE_TIME before reporting the event. This works well during
normal operation.
However, key press events can be lost during system resume on platforms
like i.MX8MQ-EVK because:
1. During the no_irq resume phase, PCIe driver restoration can take up to
200ms with IRQs disabled.
2. The power key interrupt remains pending during the no_irq phase.
3. If the key is released before IRQs are re-enabled, the timer eventually
runs but sees the key as released and skips reporting the event.
To prevent event loss during system suspend, set a pending_press flag in
the interrupt handler and report the press event from the timer callback
when the flag is set. This avoids out-of-order event delivery and keeps
the existing timer-based debounce mechanism for normal operation.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260715-b4-pwrkey-v5-4-07e7353c319e@oss.nxp.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Use local struct device pointer to avoid reference the platform_device
pointer every time.
No functional change.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Link: https://patch.msgid.link/20260715-b4-pwrkey-v5-3-07e7353c319e@oss.nxp.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Hardcoding -EINVAL discards the actual error code, which breaks probe
deferral (-EPROBE_DEFER) and loses critical diagnostic information
needed for proper kernel error handling.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Link: https://patch.msgid.link/20260715-b4-pwrkey-v5-2-07e7353c319e@oss.nxp.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add dev_err_probe() at return path of probe() to support users to
identify issues easier.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Link: https://patch.msgid.link/20260715-b4-pwrkey-v5-1-07e7353c319e@oss.nxp.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In preparation for removing the strlcat() API[1], replace its five
uses with a small append helper built on strnlen() and strscpy().
The five calls append device name fragments to a basename buffer
that grows in place across the setup functions. The helper takes
the same arguments as strlcat() and writes the same bytes, including
when a fragment is truncated.
Link: https://github.com/KSPP/linux/issues/370 [1]
Signed-off-by: Ian Bridges <icb@fastmail.org>
Link: https://patch.msgid.link/albg4Rv7QxvLJD05@dev
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The driver currently sets only the overflow interrupt enable bit
(OVR_FLOW_IEN) in the configuration register, leaving the overflow
mode bit (OVR_FLOW_M) at its default value of 0.
According to the TCA8418 datasheet (SCPS215G, Section 8.6.4.1
"Overflow Errata - Description"), both OVR_FLOW_M (Bit_5) and
OVR_FLOW_IEN (Bit_3) must be set high for the overflow interrupt
to be generated. If only OVR_FLOW_IEN is set, FIFO overflow events
are silently lost without notifying the host.
Fix this by setting OVR_FLOW_M alongside OVR_FLOW_IEN in the
configuration register.
Signed-off-by: Zhian Liang <liangzhan5dev@gmail.com>
Link: https://patch.msgid.link/20260529013900.43854-1-liangzhan5dev@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In mms114_setup_regs(), the driver mistakenly uses props->max_x instead
of props->max_y when configuring the low bits of the Y resolution
(MMS114_Y_RESOLUTION).
Fix this by using the correct property.
Fixes: 07b8481d4aff ("Input: add MELFAS mms114 touchscreen driver")
Assisted-by: Antigravity:gemini-3.5-flash
Link: https://patch.msgid.link/20260704060115.353049-3-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The driver defines the I2C packet layout using C bitfields in struct
mms114_touch. This is not portable as the layout of bitfields within a
byte is compiler-dependent and varies with endianness. On Big Endian
systems, the fields will be parsed incorrectly.
Fix this by redefining struct mms114_touch with plain u8 fields and
introducing bitwise macros to extract the values portably.
Reported-by: sashiko-bot@kernel.org
Assisted-by: Antigravity:gemini-3.5-flash
Link: https://patch.msgid.link/20260704060115.353049-2-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Sync up with mainline to pull in stable fixes to avoid merge conflicts.
|
|
In preparation for removing the strlcat() API[1], replace its uses in
i8042-acpipnpio.h.
i8042_pnp_id_to_string() accumulates a variable number of PNP ids in
a loop, which is what seq_buf is for. The kbd and aux probe functions
build a name from at most three parts that are all known up front, so
the whole construction becomes a single scnprintf() there.
Link: https://github.com/KSPP/linux/issues/370 [1]
Signed-off-by: Ian Bridges <icb@fastmail.org>
Link: https://patch.msgid.link/akyW4xkvCCROM0SE@dev
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- fix MELFAS MMS114 touchscreen driver to reject invalid touch IDs and
avoid multi-touch slot corruption
- fix a crash in the Sega Dreamcast (Maple) mouse driver when opening
the device, caused by missing driver data
- fixes for Maple drivers (keyboard, mouse, joystick) to properly order
setting driver data and device registration to avoid races
* tag 'input-for-v7.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: mms114 - fix multi-touch slot corruption
Input: maple_keyb - set driver data before registering input device
Input: maplecontrol - set driver data before registering input device
Input: maplemouse - set driver data before registering input device
Input: maplemouse - fix NULL pointer dereference in open()
|
|
linux/gpio.h is going away, so remove that since the driver already
includes linux/gpio/consumer.h.
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260710211954.1373336-10-arnd@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
If the touchscreen controller reports a touch ID of 0, the driver
calculates the slot ID as touch->id - 1, which underflows to UINT_MAX.
This is passed to input_mt_slot() as -1.
Since the input core ignores negative slot values, the active slot remains
unchanged. The driver then reports the touch coordinates for the previously
active slot, corrupting its state.
Fix this by rejecting touch reports with ID 0.
Fixes: 07b8481d4aff ("Input: add MELFAS mms114 touchscreen driver")
Cc: stable@vger.kernel.org
Reported-by: sashiko-bot@kernel.org
Assisted-by: Antigravity:gemini-3.5-flash
Link: https://patch.msgid.link/20260704060115.353049-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Linux 7.2-rc2
Done to resolve conflicts with header reorg around mod_devicetable.h
and provide a base for other inflight series that touch the includes.
|
|
Use namespaced exports for IIO consumer API functions.
This will make it easier to manage the IIO export surface. Consumer drivers
will only be provided access to a specific set of functions, thereby
restricting usage of internal IIO functions by other parts of the kernel.
This change cannot be split into several parts without breaking
bisectability, thus all of the affected drivers are modified at once.
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for power-supply
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The driver has a match table for the usb bus wired into its driver
structure, but the table is not exported with MODULE_DEVICE_TABLE().
Add the missing MODULE_DEVICE_TABLE() entry so module alias information
is generated for automatic module loading.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260704151730.42772-1-pengpeng@iscas.ac.cn
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Set maple driver data before calling input_register_device() to
ensure that it is available if the device is opened immediately and
the callback is triggered.
Cc: stable@vger.kernel.org
Assisted-by: Antigravity:gemini-3.5-flash
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Set maple driver data before calling input_register_device() to
ensure that it is available if the device is opened immediately and
the callback is triggered.
Cc: stable@vger.kernel.org
Assisted-by: Antigravity:gemini-3.5-flash
Tested-by: Florian Fuchs <fuchsfl@gmail.com>
Link: https://patch.msgid.link/akNYib9hQFNN1fA9@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Set maple driver data before calling input_register_device() to
ensure that it is available if the device is opened immediately and
the callback is triggered.
Cc: stable@vger.kernel.org
Assisted-by: Antigravity:gemini-3.5-flash
Tested-by: Florian Fuchs <fuchsfl@gmail.com>
Link: https://patch.msgid.link/akNXw45L_8bxD6QV@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
files)
Replace the #include of <linux/mod_devicetable.h> by the more specific
<linux/device-id/*.h> where applicable. For most cases the include
can be dropped completely, only a few drivers need one or two headers
added.
Acked-by: Danilo Krummrich <dakr@kernel.org>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/1a3f2007c5c5dcf555c09a4035ce3ae8ef1b6c49.1782808461.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
|
