From 1f25ca11d84a3aa01b2b12a419a1385c2f5513bc Mon Sep 17 00:00:00 2001 From: Matt Ranostay Date: Mon, 4 Jul 2016 18:54:04 -0700 Subject: iio: temperature: add support for Maxim thermocouple chips Add initial driver support for MAX6675, and MAX31855 thermocouple chips. Cc: Marek Vasut Cc: Matt Porter Signed-off-by: Matt Ranostay Signed-off-by: Jonathan Cameron --- .../bindings/iio/temperature/maxim_thermocouple.txt | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt b/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt new file mode 100644 index 000000000000..28bc5c4d965b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt @@ -0,0 +1,21 @@ +Maxim thermocouple support + +* https://datasheets.maximintegrated.com/en/ds/MAX6675.pdf +* https://datasheets.maximintegrated.com/en/ds/MAX31855.pdf + +Required properties: + + - compatible: must be "maxim,max31855" or "maxim,max6675" + - reg: SPI chip select number for the device + - spi-max-frequency: must be 4300000 + - spi-cpha: must be defined for max6675 to enable SPI mode 1 + + Refer to spi/spi-bus.txt for generic SPI slave bindings. + +Example: + + max31855@0 { + compatible = "maxim,max31855"; + reg = <0>; + spi-max-frequency = <4300000>; + }; -- cgit v1.2.3 From bcdf177d046c13db727c80ac9023b916dd878f8f Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Mon, 25 Jul 2016 15:54:54 +0200 Subject: iio: magn: DT bindings for AK8974 This adds device tree bindings for the AK8974 magnetometer, similar to those for the AK8975. Cc: devicetree@vger.kernel.org Cc: Samu Onkalo Cc: Sebastian Reichel Cc: Peter Meerwald-Stadler Acked-by: Rob Herring Signed-off-by: Linus Walleij Signed-off-by: Jonathan Cameron --- .../bindings/iio/magnetometer/ak8974.txt | 29 ++++++++++++++++++++++ 1 file changed, 29 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/magnetometer/ak8974.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/iio/magnetometer/ak8974.txt b/Documentation/devicetree/bindings/iio/magnetometer/ak8974.txt new file mode 100644 index 000000000000..77d5aba1bd8c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/magnetometer/ak8974.txt @@ -0,0 +1,29 @@ +* Asahi Kasei AK8974 magnetometer sensor + +Required properties: + +- compatible : should be "asahi-kasei,ak8974" +- reg : the I2C address of the magnetometer + +Optional properties: + +- avdd-supply: regulator supply for the analog voltage + (see regulator/regulator.txt) +- dvdd-supply: regulator supply for the digital voltage + (see regulator/regulator.txt) +- interrupts: data ready (DRDY) and interrupt (INT1) lines + from the chip, the DRDY interrupt must be placed first. + The interrupts can be triggered on rising or falling + edges alike. +- mount-matrix: an optional 3x3 mounting rotation matrix + +Example: + +ak8974@0f { + compatible = "asahi-kasei,ak8974"; + reg = <0x0f>; + avdd-supply = <&foo_reg>; + dvdd-supply = <&bar_reg>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>, + <1 IRQ_TYPE_EDGE_RISING>; +}; -- cgit v1.2.3 From 0363dfc585c5c62659be48b6de4b0f8abef4c839 Mon Sep 17 00:00:00 2001 From: Aleksei Mamlin Date: Mon, 25 Jul 2016 18:21:17 +0300 Subject: devicetree: bindings: Add vendor prefix for Domintech Co., Ltd. Add vendor-prefix for Domintech Co., Ltd. Signed-off-by: Aleksei Mamlin Acked-by: Rob Herring Signed-off-by: Jonathan Cameron --- Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + 1 file changed, 1 insertion(+) (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 2c2500df0dce..7363916bb3be 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -75,6 +75,7 @@ digilent Diglent, Inc. dlg Dialog Semiconductor dlink D-Link Corporation dmo Data Modul AG +domintech Domintech Co., Ltd. dptechnics DPTechnics dragino Dragino Technology Co., Limited ea Embedded Artists AB -- cgit v1.2.3 From b1b79f53278f2e2ec07fc8a899068fcc04ca439b Mon Sep 17 00:00:00 2001 From: Aleksei Mamlin Date: Mon, 25 Jul 2016 18:21:18 +0300 Subject: iio: accel: Add support for Domintech DMARD06 accelerometer This patch add support for Domintech DMARD05, DMARD06 and DMARD07 accelerometers. Signed-off-by: Aleksei Mamlin Acked-by: Rob Herring Signed-off-by: Jonathan Cameron --- .../devicetree/bindings/iio/accel/dmard06.txt | 19 ++ drivers/iio/accel/Kconfig | 11 + drivers/iio/accel/Makefile | 1 + drivers/iio/accel/dmard06.c | 241 +++++++++++++++++++++ 4 files changed, 272 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/accel/dmard06.txt create mode 100644 drivers/iio/accel/dmard06.c (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/iio/accel/dmard06.txt b/Documentation/devicetree/bindings/iio/accel/dmard06.txt new file mode 100644 index 000000000000..ce105a12c645 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/dmard06.txt @@ -0,0 +1,19 @@ +Device tree bindings for Domintech DMARD05, DMARD06, DMARD07 accelerometers + +Required properties: + - compatible : Should be "domintech,dmard05" + or "domintech,dmard06" + or "domintech,dmard07" + - reg : I2C address of the chip. Should be 0x1c + +Example: + &i2c1 { + /* ... */ + + accelerometer@1c { + compatible = "domintech,dmard06"; + reg = <0x1c>; + }; + + /* ... */ + }; diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig index 89d78208de3f..ee57effee549 100644 --- a/drivers/iio/accel/Kconfig +++ b/drivers/iio/accel/Kconfig @@ -50,6 +50,17 @@ config BMC150_ACCEL_SPI tristate select REGMAP_SPI +config DMARD06 + tristate "Domintech DMARD06 Digital Accelerometer Driver" + depends on OF || COMPILE_TEST + depends on I2C + help + Say yes here to build support for the Domintech low-g tri-axial + digital accelerometers: DMARD05, DMARD06, DMARD07. + + To compile this driver as a module, choose M here: the + module will be called dmard06. + config HID_SENSOR_ACCEL_3D depends on HID_SENSOR_HUB select IIO_BUFFER diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile index 6cedbecca2ee..24eba651ee78 100644 --- a/drivers/iio/accel/Makefile +++ b/drivers/iio/accel/Makefile @@ -8,6 +8,7 @@ obj-$(CONFIG_BMA220) += bma220_spi.o obj-$(CONFIG_BMC150_ACCEL) += bmc150-accel-core.o obj-$(CONFIG_BMC150_ACCEL_I2C) += bmc150-accel-i2c.o obj-$(CONFIG_BMC150_ACCEL_SPI) += bmc150-accel-spi.o +obj-$(CONFIG_DMARD06) += dmard06.o obj-$(CONFIG_HID_SENSOR_ACCEL_3D) += hid-sensor-accel-3d.o obj-$(CONFIG_KXCJK1013) += kxcjk-1013.o obj-$(CONFIG_KXSD9) += kxsd9.o diff --git a/drivers/iio/accel/dmard06.c b/drivers/iio/accel/dmard06.c new file mode 100644 index 000000000000..656ca8e1927f --- /dev/null +++ b/drivers/iio/accel/dmard06.c @@ -0,0 +1,241 @@ +/* + * IIO driver for Domintech DMARD06 accelerometer + * + * Copyright (C) 2016 Aleksei Mamlin + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + */ + +#include +#include +#include + +#define DMARD06_DRV_NAME "dmard06" + +/* Device data registers */ +#define DMARD06_CHIP_ID_REG 0x0f +#define DMARD06_TOUT_REG 0x40 +#define DMARD06_XOUT_REG 0x41 +#define DMARD06_YOUT_REG 0x42 +#define DMARD06_ZOUT_REG 0x43 +#define DMARD06_CTRL1_REG 0x44 + +/* Device ID value */ +#define DMARD05_CHIP_ID 0x05 +#define DMARD06_CHIP_ID 0x06 +#define DMARD07_CHIP_ID 0x07 + +/* Device values */ +#define DMARD05_AXIS_SCALE_VAL 15625 +#define DMARD06_AXIS_SCALE_VAL 31250 +#define DMARD06_TEMP_CENTER_VAL 25 +#define DMARD06_SIGN_BIT 7 + +/* Device power modes */ +#define DMARD06_MODE_NORMAL 0x27 +#define DMARD06_MODE_POWERDOWN 0x00 + +/* Device channels */ +#define DMARD06_ACCEL_CHANNEL(_axis, _reg) { \ + .type = IIO_ACCEL, \ + .address = _reg, \ + .channel2 = IIO_MOD_##_axis, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ + .modified = 1, \ +} + +#define DMARD06_TEMP_CHANNEL(_reg) { \ + .type = IIO_TEMP, \ + .address = _reg, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \ + BIT(IIO_CHAN_INFO_OFFSET), \ +} + +struct dmard06_data { + struct i2c_client *client; + u8 chip_id; +}; + +static const struct iio_chan_spec dmard06_channels[] = { + DMARD06_ACCEL_CHANNEL(X, DMARD06_XOUT_REG), + DMARD06_ACCEL_CHANNEL(Y, DMARD06_YOUT_REG), + DMARD06_ACCEL_CHANNEL(Z, DMARD06_ZOUT_REG), + DMARD06_TEMP_CHANNEL(DMARD06_TOUT_REG), +}; + +static int dmard06_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, long mask) +{ + struct dmard06_data *dmard06 = iio_priv(indio_dev); + int ret; + + switch (mask) { + case IIO_CHAN_INFO_RAW: + ret = i2c_smbus_read_byte_data(dmard06->client, + chan->address); + if (ret < 0) { + dev_err(&dmard06->client->dev, + "Error reading data: %d\n", ret); + return ret; + } + + *val = sign_extend32(ret, DMARD06_SIGN_BIT); + + if (dmard06->chip_id == DMARD06_CHIP_ID) + *val = *val >> 1; + + switch (chan->type) { + case IIO_ACCEL: + return IIO_VAL_INT; + case IIO_TEMP: + if (dmard06->chip_id != DMARD06_CHIP_ID) + *val = *val / 2; + return IIO_VAL_INT; + default: + return -EINVAL; + } + case IIO_CHAN_INFO_OFFSET: + switch (chan->type) { + case IIO_TEMP: + *val = DMARD06_TEMP_CENTER_VAL; + return IIO_VAL_INT; + default: + return -EINVAL; + } + case IIO_CHAN_INFO_SCALE: + switch (chan->type) { + case IIO_ACCEL: + *val = 0; + if (dmard06->chip_id == DMARD06_CHIP_ID) + *val2 = DMARD06_AXIS_SCALE_VAL; + else + *val2 = DMARD05_AXIS_SCALE_VAL; + return IIO_VAL_INT_PLUS_MICRO; + default: + return -EINVAL; + } + default: + return -EINVAL; + } +} + +static const struct iio_info dmard06_info = { + .driver_module = THIS_MODULE, + .read_raw = dmard06_read_raw, +}; + +static int dmard06_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + int ret; + struct iio_dev *indio_dev; + struct dmard06_data *dmard06; + + if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { + dev_err(&client->dev, "I2C check functionality failed\n"); + return -ENXIO; + } + + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*dmard06)); + if (!indio_dev) { + dev_err(&client->dev, "Failed to allocate iio device\n"); + return -ENOMEM; + } + + dmard06 = iio_priv(indio_dev); + dmard06->client = client; + + ret = i2c_smbus_read_byte_data(dmard06->client, DMARD06_CHIP_ID_REG); + if (ret < 0) { + dev_err(&client->dev, "Error reading chip id: %d\n", ret); + return ret; + } + + if (ret != DMARD05_CHIP_ID && ret != DMARD06_CHIP_ID && + ret != DMARD07_CHIP_ID) { + dev_err(&client->dev, "Invalid chip id: %02d\n", ret); + return -ENODEV; + } + + dmard06->chip_id = ret; + + i2c_set_clientdata(client, indio_dev); + indio_dev->dev.parent = &client->dev; + indio_dev->name = DMARD06_DRV_NAME; + indio_dev->modes = INDIO_DIRECT_MODE; + indio_dev->channels = dmard06_channels; + indio_dev->num_channels = ARRAY_SIZE(dmard06_channels); + indio_dev->info = &dmard06_info; + + return devm_iio_device_register(&client->dev, indio_dev); +} + +#ifdef CONFIG_PM_SLEEP +static int dmard06_suspend(struct device *dev) +{ + struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev)); + struct dmard06_data *dmard06 = iio_priv(indio_dev); + int ret; + + ret = i2c_smbus_write_byte_data(dmard06->client, DMARD06_CTRL1_REG, + DMARD06_MODE_POWERDOWN); + if (ret < 0) + return ret; + + return 0; +} + +static int dmard06_resume(struct device *dev) +{ + struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev)); + struct dmard06_data *dmard06 = iio_priv(indio_dev); + int ret; + + ret = i2c_smbus_write_byte_data(dmard06->client, DMARD06_CTRL1_REG, + DMARD06_MODE_NORMAL); + if (ret < 0) + return ret; + + return 0; +} + +static SIMPLE_DEV_PM_OPS(dmard06_pm_ops, dmard06_suspend, dmard06_resume); +#define DMARD06_PM_OPS (&dmard06_pm_ops) +#else +#define DMARD06_PM_OPS NULL +#endif + +static const struct i2c_device_id dmard06_id[] = { + { "dmard05", 0 }, + { "dmard06", 0 }, + { "dmard07", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, dmard06_id); + +static const struct of_device_id dmard06_of_match[] = { + { .compatible = "domintech,dmard05" }, + { .compatible = "domintech,dmard06" }, + { .compatible = "domintech,dmard07" }, + { } +}; +MODULE_DEVICE_TABLE(of, dmard06_of_match); + +static struct i2c_driver dmard06_driver = { + .probe = dmard06_probe, + .id_table = dmard06_id, + .driver = { + .name = DMARD06_DRV_NAME, + .of_match_table = of_match_ptr(dmard06_of_match), + .pm = DMARD06_PM_OPS, + }, +}; +module_i2c_driver(dmard06_driver); + +MODULE_AUTHOR("Aleksei Mamlin "); +MODULE_DESCRIPTION("Domintech DMARD06 accelerometer driver"); +MODULE_LICENSE("GPL v2"); -- cgit v1.2.3 From a4fa6509dda47e51c3582409e8630b24702970c5 Mon Sep 17 00:00:00 2001 From: Jelle van der Waa Date: Tue, 26 Jul 2016 23:23:48 +0200 Subject: iio: accel: add support for the Domintech DMARD09 3-axis accelerometer Minimal implementation of an IIO driver for the Domintech DMARD09 3-axis accelerometer. Only supports reading the x,y,z axes at the moment. Implementation based on the Android driver from the Acer Liquid E2 kernel sources. Signed-off-by: Jelle van der Waa Signed-off-by: Jonathan Cameron --- .../devicetree/bindings/i2c/trivial-devices.txt | 1 + drivers/iio/accel/Kconfig | 10 ++ drivers/iio/accel/Makefile | 1 + drivers/iio/accel/dmard09.c | 157 +++++++++++++++++++++ 4 files changed, 169 insertions(+) create mode 100644 drivers/iio/accel/dmard09.c (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index acc5cd64711c..0bc11e041cfd 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -38,6 +38,7 @@ dallas,ds4510 CPU Supervisor with Nonvolatile Memory and Programmable I/O dallas,ds75 Digital Thermometer and Thermostat dlg,da9053 DA9053: flexible system level PMIC with multicore support dlg,da9063 DA9063: system PMIC for quad-core application processors +domintech,dmard09 DMARD09: 3-axis Accelerometer epson,rx8010 I2C-BUS INTERFACE REAL TIME CLOCK MODULE epson,rx8025 High-Stability. I2C-Bus INTERFACE REAL TIME CLOCK MODULE epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig index ee57effee549..5630f2316c58 100644 --- a/drivers/iio/accel/Kconfig +++ b/drivers/iio/accel/Kconfig @@ -61,6 +61,16 @@ config DMARD06 To compile this driver as a module, choose M here: the module will be called dmard06. +config DMARD09 + tristate "Domintech DMARD09 3-axis Accelerometer Driver" + depends on I2C + help + Say yes here to get support for the Domintech DMARD09 3-axis + accelerometer. + + Choosing M will build the driver as a module. If so, the module + will be called dmard09. + config HID_SENSOR_ACCEL_3D depends on HID_SENSOR_HUB select IIO_BUFFER diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile index 24eba651ee78..e974841ec9cf 100644 --- a/drivers/iio/accel/Makefile +++ b/drivers/iio/accel/Makefile @@ -9,6 +9,7 @@ obj-$(CONFIG_BMC150_ACCEL) += bmc150-accel-core.o obj-$(CONFIG_BMC150_ACCEL_I2C) += bmc150-accel-i2c.o obj-$(CONFIG_BMC150_ACCEL_SPI) += bmc150-accel-spi.o obj-$(CONFIG_DMARD06) += dmard06.o +obj-$(CONFIG_DMARD09) += dmard09.o obj-$(CONFIG_HID_SENSOR_ACCEL_3D) += hid-sensor-accel-3d.o obj-$(CONFIG_KXCJK1013) += kxcjk-1013.o obj-$(CONFIG_KXSD9) += kxsd9.o diff --git a/drivers/iio/accel/dmard09.c b/drivers/iio/accel/dmard09.c new file mode 100644 index 000000000000..d3a28f96565c --- /dev/null +++ b/drivers/iio/accel/dmard09.c @@ -0,0 +1,157 @@ +/* + * IIO driver for the 3-axis accelerometer Domintech DMARD09. + * + * Copyright (c) 2016, Jelle van der Waa + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + */ + +#include +#include +#include +#include + +#define DMARD09_DRV_NAME "dmard09" + +#define DMARD09_REG_CHIPID 0x18 +#define DMARD09_REG_STAT 0x0A +#define DMARD09_REG_X 0x0C +#define DMARD09_REG_Y 0x0E +#define DMARD09_REG_Z 0x10 +#define DMARD09_CHIPID 0x95 + +#define DMARD09_BUF_LEN 8 +#define DMARD09_AXIS_X 0 +#define DMARD09_AXIS_Y 1 +#define DMARD09_AXIS_Z 2 +#define DMARD09_AXIS_X_OFFSET ((DMARD09_AXIS_X + 1) * 2) +#define DMARD09_AXIS_Y_OFFSET ((DMARD09_AXIS_Y + 1 )* 2) +#define DMARD09_AXIS_Z_OFFSET ((DMARD09_AXIS_Z + 1) * 2) + +struct dmard09_data { + struct i2c_client *client; +}; + +#define DMARD09_CHANNEL(_axis, offset) { \ + .type = IIO_ACCEL, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ + .modified = 1, \ + .address = offset, \ + .channel2 = IIO_MOD_##_axis, \ +} + +static const struct iio_chan_spec dmard09_channels[] = { + DMARD09_CHANNEL(X, DMARD09_AXIS_X_OFFSET), + DMARD09_CHANNEL(Y, DMARD09_AXIS_Y_OFFSET), + DMARD09_CHANNEL(Z, DMARD09_AXIS_Z_OFFSET), +}; + +static int dmard09_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, long mask) +{ + struct dmard09_data *data = iio_priv(indio_dev); + u8 buf[DMARD09_BUF_LEN]; + int ret; + s16 accel; + + switch (mask) { + case IIO_CHAN_INFO_RAW: + /* + * Read from the DMAR09_REG_STAT register, since the chip + * caches reads from the individual X, Y, Z registers. + */ + ret = i2c_smbus_read_i2c_block_data(data->client, + DMARD09_REG_STAT, + DMARD09_BUF_LEN, buf); + if (ret < 0) { + dev_err(&data->client->dev, "Error reading reg %d\n", + DMARD09_REG_STAT); + return ret; + } + + accel = get_unaligned_le16(&buf[chan->address]); + + /* Remove lower 3 bits and sign extend */ + accel <<= 4; + accel >>= 7; + + *val = accel; + + return IIO_VAL_INT; + default: + return -EINVAL; + } +} + +static const struct iio_info dmard09_info = { + .driver_module = THIS_MODULE, + .read_raw = dmard09_read_raw, +}; + +static int dmard09_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + int ret; + struct iio_dev *indio_dev; + struct dmard09_data *data; + + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); + if (!indio_dev) { + dev_err(&client->dev, "iio allocation failed\n"); + return -ENOMEM; + } + + data = iio_priv(indio_dev); + data->client = client; + + ret = i2c_smbus_read_byte_data(data->client, DMARD09_REG_CHIPID); + if (ret < 0) { + dev_err(&client->dev, "Error reading chip id %d\n", ret); + return ret; + } + + if (ret != DMARD09_CHIPID) { + dev_err(&client->dev, "Invalid chip id %d\n", ret); + return -ENODEV; + } + + i2c_set_clientdata(client, indio_dev); + indio_dev->dev.parent = &client->dev; + indio_dev->name = DMARD09_DRV_NAME; + indio_dev->modes = INDIO_DIRECT_MODE; + indio_dev->channels = dmard09_channels; + indio_dev->num_channels = ARRAY_SIZE(dmard09_channels); + indio_dev->info = &dmard09_info; + + return devm_iio_device_register(&client->dev, indio_dev); +} + +static const struct i2c_device_id dmard09_id[] = { + { "dmard09", 0}, + { }, +}; + +MODULE_DEVICE_TABLE(i2c, dmard09_id); + +static struct i2c_driver dmard09_driver = { + .driver = { + .name = DMARD09_DRV_NAME + }, + .probe = dmard09_probe, + .id_table = dmard09_id, +}; + +module_i2c_driver(dmard09_driver); + +MODULE_AUTHOR("Jelle van der Waa "); +MODULE_DESCRIPTION("DMARD09 3-axis accelerometer driver"); +MODULE_LICENSE("GPL"); -- cgit v1.2.3 From 4d671b71beefbfc145b971a11e0c3cabde94b673 Mon Sep 17 00:00:00 2001 From: Matt Ranostay Date: Fri, 19 Aug 2016 20:17:03 -0700 Subject: iio: adc: ti-adc161s626: add support for TI 1-channel differential ADCs Add support for Texas Instruments ADC141S626, and ADC161S626 chips. Signed-off-by: Matt Ranostay Signed-off-by: Jonathan Cameron --- .../devicetree/bindings/iio/adc/ti-adc161s626.txt | 16 ++ drivers/iio/adc/Kconfig | 12 + drivers/iio/adc/Makefile | 1 + drivers/iio/adc/ti-adc161s626.c | 248 +++++++++++++++++++++ 4 files changed, 277 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt create mode 100644 drivers/iio/adc/ti-adc161s626.c (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt new file mode 100644 index 000000000000..9ed2315781e4 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-adc161s626.txt @@ -0,0 +1,16 @@ +* Texas Instruments ADC141S626 and ADC161S626 chips + +Required properties: + - compatible: Should be "ti,adc141s626" or "ti,adc161s626" + - reg: spi chip select number for the device + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: +adc@0 { + compatible = "ti,adc161s626"; + reg = <0>; + spi-max-frequency = <4300000>; +}; diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig index 1de31bdd4ce4..f06cff7e2c69 100644 --- a/drivers/iio/adc/Kconfig +++ b/drivers/iio/adc/Kconfig @@ -426,6 +426,18 @@ config TI_ADC128S052 This driver can also be built as a module. If so, the module will be called ti-adc128s052. +config TI_ADC161S626 + tristate "Texas Instruments ADC161S626 1-channel differential ADC" + depends on SPI + select IIO_BUFFER + select IIO_TRIGGERED_BUFFER + help + If you say yes here you get support for Texas Instruments ADC141S626, + and ADC161S626 chips. + + This driver can also be built as a module. If so, the module will be + called ti-adc161s626. + config TI_ADS1015 tristate "Texas Instruments ADS1015 ADC" depends on I2C && !SENSORS_ADS1015 diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile index 0ba0d500eedb..1d805770c1a0 100644 --- a/drivers/iio/adc/Makefile +++ b/drivers/iio/adc/Makefile @@ -41,6 +41,7 @@ obj-$(CONFIG_ROCKCHIP_SARADC) += rockchip_saradc.o obj-$(CONFIG_TI_ADC081C) += ti-adc081c.o obj-$(CONFIG_TI_ADC0832) += ti-adc0832.o obj-$(CONFIG_TI_ADC128S052) += ti-adc128s052.o +obj-$(CONFIG_TI_ADC161S626) += ti-adc161s626.o obj-$(CONFIG_TI_ADS1015) += ti-ads1015.o obj-$(CONFIG_TI_ADS8688) += ti-ads8688.o obj-$(CONFIG_TI_AM335X_ADC) += ti_am335x_adc.o diff --git a/drivers/iio/adc/ti-adc161s626.c b/drivers/iio/adc/ti-adc161s626.c new file mode 100644 index 000000000000..f94b69f9c288 --- /dev/null +++ b/drivers/iio/adc/ti-adc161s626.c @@ -0,0 +1,248 @@ +/* + * ti-adc161s626.c - Texas Instruments ADC161S626 1-channel differential ADC + * + * ADC Devices Supported: + * adc141s626 - 14-bit ADC + * adc161s626 - 16-bit ADC + * + * Copyright (C) 2016 Matt Ranostay + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define TI_ADC_DRV_NAME "ti-adc161s626" + +enum { + TI_ADC141S626, + TI_ADC161S626, +}; + +static const struct iio_chan_spec ti_adc141s626_channels[] = { + { + .type = IIO_VOLTAGE, + .channel = 0, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), + .scan_index = 0, + .scan_type = { + .sign = 's', + .realbits = 14, + .storagebits = 16, + }, + }, + IIO_CHAN_SOFT_TIMESTAMP(1), +}; + +static const struct iio_chan_spec ti_adc161s626_channels[] = { + { + .type = IIO_VOLTAGE, + .channel = 0, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), + .scan_index = 0, + .scan_type = { + .sign = 's', + .realbits = 16, + .storagebits = 16, + }, + }, + IIO_CHAN_SOFT_TIMESTAMP(1), +}; + +struct ti_adc_data { + struct iio_dev *indio_dev; + struct spi_device *spi; + u8 read_size; + u8 shift; + + u8 buffer[16] ____cacheline_aligned; +}; + +static int ti_adc_read_measurement(struct ti_adc_data *data, + struct iio_chan_spec const *chan, int *val) +{ + int ret; + + switch (data->read_size) { + case 2: { + __be16 buf; + + ret = spi_read(data->spi, (void *) &buf, 2); + if (ret) + return ret; + + *val = be16_to_cpu(buf); + break; + } + case 3: { + __be32 buf; + + ret = spi_read(data->spi, (void *) &buf, 3); + if (ret) + return ret; + + *val = be32_to_cpu(buf) >> 8; + break; + } + default: + return -EINVAL; + } + + *val = sign_extend32(*val >> data->shift, chan->scan_type.realbits - 1); + + return 0; +} + +static irqreturn_t ti_adc_trigger_handler(int irq, void *private) +{ + struct iio_poll_func *pf = private; + struct iio_dev *indio_dev = pf->indio_dev; + struct ti_adc_data *data = iio_priv(indio_dev); + int ret; + + ret = ti_adc_read_measurement(data, &indio_dev->channels[0], + (int *) &data->buffer); + if (!ret) + iio_push_to_buffers_with_timestamp(indio_dev, + data->buffer, + iio_get_time_ns(indio_dev)); + + iio_trigger_notify_done(indio_dev->trig); + + return IRQ_HANDLED; +} + +static int ti_adc_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, long mask) +{ + struct ti_adc_data *data = iio_priv(indio_dev); + int ret; + + if (mask != IIO_CHAN_INFO_RAW) + return -EINVAL; + + ret = iio_device_claim_direct_mode(indio_dev); + if (ret) + return ret; + + ret = ti_adc_read_measurement(data, chan, val); + iio_device_release_direct_mode(indio_dev); + + if (!ret) + return IIO_VAL_INT; + + return 0; +} + +static const struct iio_info ti_adc_info = { + .driver_module = THIS_MODULE, + .read_raw = ti_adc_read_raw, +}; + +static int ti_adc_probe(struct spi_device *spi) +{ + struct iio_dev *indio_dev; + struct ti_adc_data *data; + int ret; + + indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*data)); + if (!indio_dev) + return -ENOMEM; + + indio_dev->info = &ti_adc_info; + indio_dev->dev.parent = &spi->dev; + indio_dev->dev.of_node = spi->dev.of_node; + indio_dev->name = TI_ADC_DRV_NAME; + indio_dev->modes = INDIO_DIRECT_MODE; + spi_set_drvdata(spi, indio_dev); + + data = iio_priv(indio_dev); + data->spi = spi; + + switch (spi_get_device_id(spi)->driver_data) { + case TI_ADC141S626: + indio_dev->channels = ti_adc141s626_channels; + indio_dev->num_channels = ARRAY_SIZE(ti_adc141s626_channels); + data->shift = 0; + data->read_size = 2; + break; + case TI_ADC161S626: + indio_dev->channels = ti_adc161s626_channels; + indio_dev->num_channels = ARRAY_SIZE(ti_adc161s626_channels); + data->shift = 6; + data->read_size = 3; + break; + } + + ret = iio_triggered_buffer_setup(indio_dev, NULL, + ti_adc_trigger_handler, NULL); + if (ret) + return ret; + + ret = iio_device_register(indio_dev); + if (ret) + goto error_unreg_buffer; + + return 0; + +error_unreg_buffer: + iio_triggered_buffer_cleanup(indio_dev); + + return ret; +} + +static int ti_adc_remove(struct spi_device *spi) +{ + struct iio_dev *indio_dev = spi_get_drvdata(spi); + + iio_device_unregister(indio_dev); + iio_triggered_buffer_cleanup(indio_dev); + + return 0; +} + +static const struct of_device_id ti_adc_dt_ids[] = { + { .compatible = "ti,adc141s626", }, + { .compatible = "ti,adc161s626", }, + {} +}; +MODULE_DEVICE_TABLE(of, ti_adc_dt_ids); + +static const struct spi_device_id ti_adc_id[] = { + {"adc141s626", TI_ADC141S626}, + {"adc161s626", TI_ADC161S626}, + {}, +}; +MODULE_DEVICE_TABLE(spi, ti_adc_id); + +static struct spi_driver ti_adc_driver = { + .driver = { + .name = TI_ADC_DRV_NAME, + .of_match_table = of_match_ptr(ti_adc_dt_ids), + }, + .probe = ti_adc_probe, + .remove = ti_adc_remove, + .id_table = ti_adc_id, +}; +module_spi_driver(ti_adc_driver); + +MODULE_AUTHOR("Matt Ranostay "); +MODULE_DESCRIPTION("Texas Instruments ADC1x1S 1-channel differential ADC"); +MODULE_LICENSE("GPL"); -- cgit v1.2.3 From ce08cc986ed6bcd43fcbef83ef6efc62a2d44eef Mon Sep 17 00:00:00 2001 From: Matt Ranostay Date: Fri, 19 Aug 2016 13:36:11 -0700 Subject: iio: chemical: atlas-ph-sensor: add ORP feature Signed-off-by: Matt Ranostay Signed-off-by: Jonathan Cameron --- .../bindings/iio/chemical/atlas,orp-sm.txt | 22 +++++++++ drivers/iio/chemical/Kconfig | 1 + drivers/iio/chemical/atlas-ph-sensor.c | 53 +++++++++++++++++++++- 3 files changed, 75 insertions(+), 1 deletion(-) create mode 100644 Documentation/devicetree/bindings/iio/chemical/atlas,orp-sm.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/iio/chemical/atlas,orp-sm.txt b/Documentation/devicetree/bindings/iio/chemical/atlas,orp-sm.txt new file mode 100644 index 000000000000..5d8b687d5edc --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/atlas,orp-sm.txt @@ -0,0 +1,22 @@ +* Atlas Scientific ORP-SM OEM sensor + +https://www.atlas-scientific.com/_files/_datasheets/_oem/ORP_oem_datasheet.pdf + +Required properties: + + - compatible: must be "atlas,orp-sm" + - reg: the I2C address of the sensor + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + +Example: + +atlas@66 { + compatible = "atlas,orp-sm"; + reg = <0x66>; + interrupt-parent = <&gpio1>; + interrupts = <16 2>; +}; diff --git a/drivers/iio/chemical/Kconfig b/drivers/iio/chemical/Kconfig index 4bcc025e8c8a..cea7f9857a1f 100644 --- a/drivers/iio/chemical/Kconfig +++ b/drivers/iio/chemical/Kconfig @@ -16,6 +16,7 @@ config ATLAS_PH_SENSOR Atlas Scientific OEM SM sensors: * pH SM sensor * EC SM sensor + * ORP SM sensor To compile this driver as module, choose M here: the module will be called atlas-ph-sensor. diff --git a/drivers/iio/chemical/atlas-ph-sensor.c b/drivers/iio/chemical/atlas-ph-sensor.c index c0a0ebbbd54a..84fbff32b96d 100644 --- a/drivers/iio/chemical/atlas-ph-sensor.c +++ b/drivers/iio/chemical/atlas-ph-sensor.c @@ -66,12 +66,17 @@ #define ATLAS_REG_TDS_DATA 0x1c #define ATLAS_REG_PSS_DATA 0x20 +#define ATLAS_REG_ORP_CALIB_STATUS 0x0d +#define ATLAS_REG_ORP_DATA 0x0e + #define ATLAS_PH_INT_TIME_IN_US 450000 #define ATLAS_EC_INT_TIME_IN_US 650000 +#define ATLAS_ORP_INT_TIME_IN_US 450000 enum { ATLAS_PH_SM, ATLAS_EC_SM, + ATLAS_ORP_SM, }; struct atlas_data { @@ -159,6 +164,23 @@ static const struct iio_chan_spec atlas_ec_channels[] = { }, }; +static const struct iio_chan_spec atlas_orp_channels[] = { + { + .type = IIO_VOLTAGE, + .address = ATLAS_REG_ORP_DATA, + .info_mask_separate = + BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE), + .scan_index = 0, + .scan_type = { + .sign = 's', + .realbits = 32, + .storagebits = 32, + .endianness = IIO_BE, + }, + }, + IIO_CHAN_SOFT_TIMESTAMP(1), +}; + static int atlas_check_ph_calibration(struct atlas_data *data) { struct device *dev = &data->client->dev; @@ -224,6 +246,22 @@ static int atlas_check_ec_calibration(struct atlas_data *data) return 0; } +static int atlas_check_orp_calibration(struct atlas_data *data) +{ + struct device *dev = &data->client->dev; + int ret; + unsigned int val; + + ret = regmap_read(data->regmap, ATLAS_REG_ORP_CALIB_STATUS, &val); + if (ret) + return ret; + + if (!val) + dev_warn(dev, "device has not been calibrated\n"); + + return 0; +}; + struct atlas_device { const struct iio_chan_spec *channels; int num_channels; @@ -248,7 +286,13 @@ static struct atlas_device atlas_devices[] = { .calibration = &atlas_check_ec_calibration, .delay = ATLAS_EC_INT_TIME_IN_US, }, - + [ATLAS_ORP_SM] = { + .channels = atlas_orp_channels, + .num_channels = 2, + .data_reg = ATLAS_REG_ORP_DATA, + .calibration = &atlas_check_orp_calibration, + .delay = ATLAS_ORP_INT_TIME_IN_US, + }, }; static int atlas_set_powermode(struct atlas_data *data, int on) @@ -386,6 +430,7 @@ static int atlas_read_raw(struct iio_dev *indio_dev, case IIO_PH: case IIO_CONCENTRATION: case IIO_ELECTRICALCONDUCTIVITY: + case IIO_VOLTAGE: ret = iio_device_claim_direct_mode(indio_dev); if (ret) return ret; @@ -422,6 +467,10 @@ static int atlas_read_raw(struct iio_dev *indio_dev, *val = 0; /* 0.000000001 */ *val2 = 1000; return IIO_VAL_INT_PLUS_NANO; + case IIO_VOLTAGE: + *val = 1; /* 0.1 */ + *val2 = 10; + break; default: return -EINVAL; } @@ -457,6 +506,7 @@ static const struct iio_info atlas_info = { static const struct i2c_device_id atlas_id[] = { { "atlas-ph-sm", ATLAS_PH_SM}, { "atlas-ec-sm", ATLAS_EC_SM}, + { "atlas-orp-sm", ATLAS_ORP_SM}, {} }; MODULE_DEVICE_TABLE(i2c, atlas_id); @@ -464,6 +514,7 @@ MODULE_DEVICE_TABLE(i2c, atlas_id); static const struct of_device_id atlas_dt_ids[] = { { .compatible = "atlas,ph-sm", .data = (void *)ATLAS_PH_SM, }, { .compatible = "atlas,ec-sm", .data = (void *)ATLAS_EC_SM, }, + { .compatible = "atlas,orp-sm", .data = (void *)ATLAS_ORP_SM, }, { } }; MODULE_DEVICE_TABLE(of, atlas_dt_ids); -- cgit v1.2.3 From 3ad16a39eda5a77510475f2c0d384312f1db105f Mon Sep 17 00:00:00 2001 From: Zhiyong Tao Date: Thu, 18 Aug 2016 15:11:35 +0800 Subject: dt-bindings: auxadc: Add binding document for Mediatek auxadc. The commit adds the device tree binding documentation for the mediatek auxadc found on Mediatek MT2701. Thermal gets auxadc sample data by iio device. So the commit changes auxadc device tree binding documentation from /soc/mediatek/auxadc.txt to /iio/adc/mt6577_auxadc.txt. Acked-by: Rob Herring Signed-off-by: Zhiyong Tao Signed-off-by: Jonathan Cameron --- .../devicetree/bindings/iio/adc/mt6577_auxadc.txt | 29 ++++++++++++++++++++++ .../devicetree/bindings/soc/mediatek/auxadc.txt | 21 ---------------- 2 files changed, 29 insertions(+), 21 deletions(-) create mode 100644 Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt delete mode 100644 Documentation/devicetree/bindings/soc/mediatek/auxadc.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt b/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt new file mode 100644 index 000000000000..68c45cbbe3d9 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt @@ -0,0 +1,29 @@ +* Mediatek AUXADC - Analog to Digital Converter on Mediatek mobile soc (mt65xx/mt81xx/mt27xx) +=============== + +The Auxiliary Analog/Digital Converter (AUXADC) is an ADC found +in some Mediatek SoCs which among other things measures the temperatures +in the SoC. It can be used directly with register accesses, but it is also +used by thermal controller which reads the temperatures from the AUXADC +directly via its own bus interface. See +Documentation/devicetree/bindings/thermal/mediatek-thermal.txt +for the Thermal Controller which holds a phandle to the AUXADC. + +Required properties: + - compatible: Should be one of: + - "mediatek,mt2701-auxadc": For MT2701 family of SoCs + - "mediatek,mt8173-auxadc": For MT8173 family of SoCs + - reg: Address range of the AUXADC unit. + - clocks: Should contain a clock specifier for each entry in clock-names + - clock-names: Should contain "main". + - #io-channel-cells: Should be 1, see ../iio-bindings.txt + +Example: + +auxadc: adc@11001000 { + compatible = "mediatek,mt2701-auxadc"; + reg = <0 0x11001000 0 0x1000>; + clocks = <&pericfg CLK_PERI_AUXADC>; + clock-names = "main"; + #io-channel-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/soc/mediatek/auxadc.txt b/Documentation/devicetree/bindings/soc/mediatek/auxadc.txt deleted file mode 100644 index bdb782918a72..000000000000 --- a/Documentation/devicetree/bindings/soc/mediatek/auxadc.txt +++ /dev/null @@ -1,21 +0,0 @@ -MediaTek AUXADC -=============== - -The Auxiliary Analog/Digital Converter (AUXADC) is an ADC found -in some Mediatek SoCs which among other things measures the temperatures -in the SoC. It can be used directly with register accesses, but it is also -used by thermal controller which reads the temperatures from the AUXADC -directly via its own bus interface. See -Documentation/devicetree/bindings/thermal/mediatek-thermal.txt -for the Thermal Controller which holds a phandle to the AUXADC. - -Required properties: -- compatible: Must be "mediatek,mt8173-auxadc" -- reg: Address range of the AUXADC unit - -Example: - -auxadc: auxadc@11001000 { - compatible = "mediatek,mt8173-auxadc"; - reg = <0 0x11001000 0 0x1000>; -}; -- cgit v1.2.3 From 87557ade38f3d465f4935d63d74a7590e7d69e1a Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Tue, 16 Aug 2016 15:33:27 +0200 Subject: iio: accel: kxsd9: Add device tree bindings This accelerometer can be probed from the device tree, so it needs to have proper documentation of it's device tree bindings. Cc: devicetree@vger.kernel.org Signed-off-by: Linus Walleij Acked-by: Rob Herring Signed-off-by: Jonathan Cameron --- .../devicetree/bindings/iio/accel/kionix,kxsd9.txt | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.txt b/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.txt new file mode 100644 index 000000000000..b25bf3a77e0f --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.txt @@ -0,0 +1,22 @@ +Kionix KXSD9 Accelerometer device tree bindings + +Required properties: + - compatible: should be set to "kionix,kxsd9" + - reg: i2c slave address + +Optional properties: + - vdd-supply: The input supply for VDD + - iovdd-supply: The input supply for IOVDD + - interrupts: The movement detection interrupt + - mount-matrix: See mount-matrix.txt + +Example: + +kxsd9@18 { + compatible = "kionix,kxsd9"; + reg = <0x18>; + interrupt-parent = <&foo>; + interrupts = <57 IRQ_TYPE_EDGE_FALLING>; + iovdd-supply = <&bar>; + vdd-supply = <&baz>; +}; -- cgit v1.2.3 From 50a6edb1b6e08643442386e8f81acc8123d17931 Mon Sep 17 00:00:00 2001 From: Akinobu Mita Date: Sun, 28 Aug 2016 23:52:49 +0900 Subject: iio: adc: add ADC12130/ADC12132/ADC12138 ADC driver This adds Texas Instruments' ADC12130/ADC12132/ADC12138 12-bit plus sign ADC driver. I have tested with the ADC12138. The ADC12130 and ADC12132 are not tested but these are similar to ADC12138 except that the mode programming instruction is a bit different. Signed-off-by: Akinobu Mita Acked-by: Rob Herring Cc: Jonathan Cameron Cc: Hartmut Knaack Cc: Lars-Peter Clausen Cc: Peter Meerwald Signed-off-by: Jonathan Cameron --- .../devicetree/bindings/iio/adc/ti-adc12138.txt | 37 ++ drivers/iio/adc/Kconfig | 12 + drivers/iio/adc/Makefile | 1 + drivers/iio/adc/ti-adc12138.c | 552 +++++++++++++++++++++ 4 files changed, 602 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt create mode 100644 drivers/iio/adc/ti-adc12138.c (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt new file mode 100644 index 000000000000..049a1d36f013 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt @@ -0,0 +1,37 @@ +* Texas Instruments' ADC12130/ADC12132/ADC12138 + +Required properties: + - compatible: Should be one of + * "ti,adc12130" + * "ti,adc12132" + * "ti,adc12138" + - reg: SPI chip select number for the device + - interrupts: Should contain interrupt for EOC (end of conversion) + - clocks: phandle to conversion clock input + - spi-max-frequency: Definision as per + Documentation/devicetree/bindings/spi/spi-bus.txt + - vref-p-supply: The regulator supply for positive analog voltage reference + +Optional properties: + - vref-n-supply: The regulator supply for negative analog voltage reference + (Note that this must not go below GND or exceed vref-p) + If not specified, this is assumed to be analog ground. + - ti,acquisition-time: The number of conversion clock periods for the S/H's + acquisition time. Should be one of 6, 10, 18, 34. If not specified, + default value of 10 is used. + For high source impedances, this value can be increased to 18 or 34. + For less ADC accuracy and/or slower CCLK frequencies this value may be + decreased to 6. See section 6.0 INPUT SOURCE RESISTANCE in the + datasheet for details. + +Example: +adc@0 { + compatible = "ti,adc12138"; + reg = <0>; + interrupts = <28 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&gpio1>; + clocks = <&cclk>; + vref-p-supply = <&ldo4_reg>; + spi-max-frequency = <5000000>; + ti,acquisition-time = <6>; +}; diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig index 6eac9236dff1..9f8e3813930e 100644 --- a/drivers/iio/adc/Kconfig +++ b/drivers/iio/adc/Kconfig @@ -438,6 +438,18 @@ config TI_ADC0832 This driver can also be built as a module. If so, the module will be called ti-adc0832. +config TI_ADC12138 + tristate "Texas Instruments ADC12130/ADC12132/ADC12138" + depends on SPI + select IIO_BUFFER + select IIO_TRIGGERED_BUFFER + help + If you say yes here you get support for Texas Instruments ADC12130, + ADC12132 and ADC12138 chips. + + This driver can also be built as a module. If so, the module will be + called ti-adc12138. + config TI_ADC128S052 tristate "Texas Instruments ADC128S052/ADC122S021/ADC124S021" depends on SPI diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile index f46dd1fdebae..d1a20b658c9a 100644 --- a/drivers/iio/adc/Makefile +++ b/drivers/iio/adc/Makefile @@ -42,6 +42,7 @@ obj-$(CONFIG_QCOM_SPMI_VADC) += qcom-spmi-vadc.o obj-$(CONFIG_ROCKCHIP_SARADC) += rockchip_saradc.o obj-$(CONFIG_TI_ADC081C) += ti-adc081c.o obj-$(CONFIG_TI_ADC0832) += ti-adc0832.o +obj-$(CONFIG_TI_ADC12138) += ti-adc12138.o obj-$(CONFIG_TI_ADC128S052) += ti-adc128s052.o obj-$(CONFIG_TI_ADC161S626) += ti-adc161s626.o obj-$(CONFIG_TI_ADS1015) += ti-ads1015.o diff --git a/drivers/iio/adc/ti-adc12138.c b/drivers/iio/adc/ti-adc12138.c new file mode 100644 index 000000000000..072f03bfe6a0 --- /dev/null +++ b/drivers/iio/adc/ti-adc12138.c @@ -0,0 +1,552 @@ +/* + * ADC12130/ADC12132/ADC12138 12-bit plus sign ADC driver + * + * Copyright (c) 2016 Akinobu Mita + * + * This file is subject to the terms and conditions of version 2 of + * the GNU General Public License. See the file COPYING in the main + * directory of this archive for more details. + * + * Datasheet: http://www.ti.com/lit/ds/symlink/adc12138.pdf + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define ADC12138_MODE_AUTO_CAL 0x08 +#define ADC12138_MODE_READ_STATUS 0x0c +#define ADC12138_MODE_ACQUISITION_TIME_6 0x0e +#define ADC12138_MODE_ACQUISITION_TIME_10 0x4e +#define ADC12138_MODE_ACQUISITION_TIME_18 0x8e +#define ADC12138_MODE_ACQUISITION_TIME_34 0xce + +#define ADC12138_STATUS_CAL BIT(6) + +enum { + adc12130, + adc12132, + adc12138, +}; + +struct adc12138 { + struct spi_device *spi; + unsigned int id; + /* conversion clock */ + struct clk *cclk; + /* positive analog voltage reference */ + struct regulator *vref_p; + /* negative analog voltage reference */ + struct regulator *vref_n; + struct mutex lock; + struct completion complete; + /* The number of cclk periods for the S/H's acquisition time */ + unsigned int acquisition_time; + + u8 tx_buf[2] ____cacheline_aligned; + u8 rx_buf[2]; +}; + +#define ADC12138_VOLTAGE_CHANNEL(chan) \ + { \ + .type = IIO_VOLTAGE, \ + .indexed = 1, \ + .channel = chan, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) \ + | BIT(IIO_CHAN_INFO_OFFSET), \ + .scan_index = chan, \ + .scan_type = { \ + .sign = 's', \ + .realbits = 13, \ + .storagebits = 16, \ + .shift = 3, \ + .endianness = IIO_BE, \ + }, \ + } + +#define ADC12138_VOLTAGE_CHANNEL_DIFF(chan1, chan2, si) \ + { \ + .type = IIO_VOLTAGE, \ + .indexed = 1, \ + .channel = (chan1), \ + .channel2 = (chan2), \ + .differential = 1, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) \ + | BIT(IIO_CHAN_INFO_OFFSET), \ + .scan_index = si, \ + .scan_type = { \ + .sign = 's', \ + .realbits = 13, \ + .storagebits = 16, \ + .shift = 3, \ + .endianness = IIO_BE, \ + }, \ + } + +static const struct iio_chan_spec adc12132_channels[] = { + ADC12138_VOLTAGE_CHANNEL(0), + ADC12138_VOLTAGE_CHANNEL(1), + ADC12138_VOLTAGE_CHANNEL_DIFF(0, 1, 2), + ADC12138_VOLTAGE_CHANNEL_DIFF(1, 0, 3), + IIO_CHAN_SOFT_TIMESTAMP(4), +}; + +static const struct iio_chan_spec adc12138_channels[] = { + ADC12138_VOLTAGE_CHANNEL(0), + ADC12138_VOLTAGE_CHANNEL(1), + ADC12138_VOLTAGE_CHANNEL(2), + ADC12138_VOLTAGE_CHANNEL(3), + ADC12138_VOLTAGE_CHANNEL(4), + ADC12138_VOLTAGE_CHANNEL(5), + ADC12138_VOLTAGE_CHANNEL(6), + ADC12138_VOLTAGE_CHANNEL(7), + ADC12138_VOLTAGE_CHANNEL_DIFF(0, 1, 8), + ADC12138_VOLTAGE_CHANNEL_DIFF(1, 0, 9), + ADC12138_VOLTAGE_CHANNEL_DIFF(2, 3, 10), + ADC12138_VOLTAGE_CHANNEL_DIFF(3, 2, 11), + ADC12138_VOLTAGE_CHANNEL_DIFF(4, 5, 12), + ADC12138_VOLTAGE_CHANNEL_DIFF(5, 4, 13), + ADC12138_VOLTAGE_CHANNEL_DIFF(6, 7, 14), + ADC12138_VOLTAGE_CHANNEL_DIFF(7, 6, 15), + IIO_CHAN_SOFT_TIMESTAMP(16), +}; + +static int adc12138_mode_programming(struct adc12138 *adc, u8 mode, + void *rx_buf, int len) +{ + struct spi_transfer xfer = { + .tx_buf = adc->tx_buf, + .rx_buf = adc->rx_buf, + .len = len, + }; + int ret; + + /* Skip unused bits for ADC12130 and ADC12132 */ + if (adc->id != adc12138) + mode = (mode & 0xc0) | ((mode & 0x0f) << 2); + + adc->tx_buf[0] = mode; + + ret = spi_sync_transfer(adc->spi, &xfer, 1); + if (ret) + return ret; + + memcpy(rx_buf, adc->rx_buf, len); + + return 0; +} + +static int adc12138_read_status(struct adc12138 *adc) +{ + u8 rx_buf[2]; + int ret; + + ret = adc12138_mode_programming(adc, ADC12138_MODE_READ_STATUS, + rx_buf, 2); + if (ret) + return ret; + + return (rx_buf[0] << 1) | (rx_buf[1] >> 7); +} + +static int __adc12138_start_conv(struct adc12138 *adc, + struct iio_chan_spec const *channel, + void *data, int len) + +{ + const u8 ch_to_mux[] = { 0, 4, 1, 5, 2, 6, 3, 7 }; + u8 mode = (ch_to_mux[channel->channel] << 4) | + (channel->differential ? 0 : 0x80); + + return adc12138_mode_programming(adc, mode, data, len); +} + +static int adc12138_start_conv(struct adc12138 *adc, + struct iio_chan_spec const *channel) +{ + u8 trash; + + return __adc12138_start_conv(adc, channel, &trash, 1); +} + +static int adc12138_start_and_read_conv(struct adc12138 *adc, + struct iio_chan_spec const *channel, + __be16 *data) +{ + return __adc12138_start_conv(adc, channel, data, 2); +} + +static int adc12138_read_conv_data(struct adc12138 *adc, __be16 *value) +{ + /* Issue a read status instruction and read previous conversion data */ + return adc12138_mode_programming(adc, ADC12138_MODE_READ_STATUS, + value, sizeof(*value)); +} + +static int adc12138_wait_eoc(struct adc12138 *adc, unsigned long timeout) +{ + if (!wait_for_completion_timeout(&adc->complete, timeout)) + return -ETIMEDOUT; + + return 0; +} + +static int adc12138_adc_conversion(struct adc12138 *adc, + struct iio_chan_spec const *channel, + __be16 *value) +{ + int ret; + + reinit_completion(&adc->complete); + + ret = adc12138_start_conv(adc, channel); + if (ret) + return ret; + + ret = adc12138_wait_eoc(adc, msecs_to_jiffies(100)); + if (ret) + return ret; + + return adc12138_read_conv_data(adc, value); +} + +static int adc12138_read_raw(struct iio_dev *iio, + struct iio_chan_spec const *channel, int *value, + int *shift, long mask) +{ + struct adc12138 *adc = iio_priv(iio); + int ret; + __be16 data; + + switch (mask) { + case IIO_CHAN_INFO_RAW: + mutex_lock(&adc->lock); + ret = adc12138_adc_conversion(adc, channel, &data); + mutex_unlock(&adc->lock); + if (ret) + return ret; + + *value = sign_extend32(be16_to_cpu(data) >> 3, 12); + + return IIO_VAL_INT; + case IIO_CHAN_INFO_SCALE: + ret = regulator_get_voltage(adc->vref_p); + if (ret < 0) + return ret; + *value = ret; + + if (!IS_ERR(adc->vref_n)) { + ret = regulator_get_voltage(adc->vref_n); + if (ret < 0) + return ret; + *value -= ret; + } + + /* convert regulator output voltage to mV */ + *value /= 1000; + *shift = channel->scan_type.realbits - 1; + + return IIO_VAL_FRACTIONAL_LOG2; + case IIO_CHAN_INFO_OFFSET: + if (!IS_ERR(adc->vref_n)) { + *value = regulator_get_voltage(adc->vref_n); + if (*value < 0) + return *value; + } else { + *value = 0; + } + + /* convert regulator output voltage to mV */ + *value /= 1000; + + return IIO_VAL_INT; + } + + return -EINVAL; +} + +static const struct iio_info adc12138_info = { + .read_raw = adc12138_read_raw, + .driver_module = THIS_MODULE, +}; + +static int adc12138_init(struct adc12138 *adc) +{ + int ret; + int status; + u8 mode; + u8 trash; + + reinit_completion(&adc->complete); + + ret = adc12138_mode_programming(adc, ADC12138_MODE_AUTO_CAL, &trash, 1); + if (ret) + return ret; + + /* data output at this time has no significance */ + status = adc12138_read_status(adc); + if (status < 0) + return status; + + adc12138_wait_eoc(adc, msecs_to_jiffies(100)); + + status = adc12138_read_status(adc); + if (status & ADC12138_STATUS_CAL) { + dev_warn(&adc->spi->dev, + "Auto Cal sequence is still in progress: %#x\n", + status); + return -EIO; + } + + switch (adc->acquisition_time) { + case 6: + mode = ADC12138_MODE_ACQUISITION_TIME_6; + break; + case 10: + mode = ADC12138_MODE_ACQUISITION_TIME_10; + break; + case 18: + mode = ADC12138_MODE_ACQUISITION_TIME_18; + break; + case 34: + mode = ADC12138_MODE_ACQUISITION_TIME_34; + break; + default: + return -EINVAL; + } + + return adc12138_mode_programming(adc, mode, &trash, 1); +} + +static irqreturn_t adc12138_trigger_handler(int irq, void *p) +{ + struct iio_poll_func *pf = p; + struct iio_dev *indio_dev = pf->indio_dev; + struct adc12138 *adc = iio_priv(indio_dev); + __be16 data[20] = { }; /* 16x 2 bytes ADC data + 8 bytes timestamp */ + __be16 trash; + int ret; + int scan_index; + int i = 0; + + mutex_lock(&adc->lock); + + for_each_set_bit(scan_index, indio_dev->active_scan_mask, + indio_dev->masklength) { + const struct iio_chan_spec *scan_chan = + &indio_dev->channels[scan_index]; + + reinit_completion(&adc->complete); + + ret = adc12138_start_and_read_conv(adc, scan_chan, + i ? &data[i - 1] : &trash); + if (ret) { + dev_warn(&adc->spi->dev, + "failed to start conversion\n"); + goto out; + } + + ret = adc12138_wait_eoc(adc, msecs_to_jiffies(100)); + if (ret) { + dev_warn(&adc->spi->dev, "wait eoc timeout\n"); + goto out; + } + + i++; + } + + if (i) { + ret = adc12138_read_conv_data(adc, &data[i - 1]); + if (ret) { + dev_warn(&adc->spi->dev, + "failed to get conversion data\n"); + goto out; + } + } + + iio_push_to_buffers_with_timestamp(indio_dev, data, + iio_get_time_ns(indio_dev)); +out: + mutex_unlock(&adc->lock); + + iio_trigger_notify_done(indio_dev->trig); + + return IRQ_HANDLED; +} + +static irqreturn_t adc12138_eoc_handler(int irq, void *p) +{ + struct iio_dev *indio_dev = p; + struct adc12138 *adc = iio_priv(indio_dev); + + complete(&adc->complete); + + return IRQ_HANDLED; +} + +static int adc12138_probe(struct spi_device *spi) +{ + struct iio_dev *indio_dev; + struct adc12138 *adc; + int ret; + + indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*adc)); + if (!indio_dev) + return -ENOMEM; + + adc = iio_priv(indio_dev); + adc->spi = spi; + adc->id = spi_get_device_id(spi)->driver_data; + mutex_init(&adc->lock); + init_completion(&adc->complete); + + indio_dev->name = spi_get_device_id(spi)->name; + indio_dev->dev.parent = &spi->dev; + indio_dev->info = &adc12138_info; + indio_dev->modes = INDIO_DIRECT_MODE; + + switch (adc->id) { + case adc12130: + case adc12132: + indio_dev->channels = adc12132_channels; + indio_dev->num_channels = ARRAY_SIZE(adc12132_channels); + break; + case adc12138: + indio_dev->channels = adc12138_channels; + indio_dev->num_channels = ARRAY_SIZE(adc12138_channels); + break; + default: + return -EINVAL; + } + + ret = of_property_read_u32(spi->dev.of_node, "ti,acquisition-time", + &adc->acquisition_time); + if (ret) + adc->acquisition_time = 10; + + adc->cclk = devm_clk_get(&spi->dev, NULL); + if (IS_ERR(adc->cclk)) + return PTR_ERR(adc->cclk); + + adc->vref_p = devm_regulator_get(&spi->dev, "vref-p"); + if (IS_ERR(adc->vref_p)) + return PTR_ERR(adc->vref_p); + + adc->vref_n = devm_regulator_get_optional(&spi->dev, "vref-n"); + if (IS_ERR(adc->vref_n)) { + /* + * Assume vref_n is 0V if an optional regulator is not + * specified, otherwise return the error code. + */ + ret = PTR_ERR(adc->vref_n); + if (ret != -ENODEV) + return ret; + } + + ret = devm_request_irq(&spi->dev, spi->irq, adc12138_eoc_handler, + IRQF_TRIGGER_RISING, indio_dev->name, indio_dev); + if (ret) + return ret; + + ret = clk_prepare_enable(adc->cclk); + if (ret) + return ret; + + ret = regulator_enable(adc->vref_p); + if (ret) + goto err_clk_disable; + + if (!IS_ERR(adc->vref_n)) { + ret = regulator_enable(adc->vref_n); + if (ret) + goto err_vref_p_disable; + } + + ret = adc12138_init(adc); + if (ret) + goto err_vref_n_disable; + + spi_set_drvdata(spi, indio_dev); + + ret = iio_triggered_buffer_setup(indio_dev, NULL, + adc12138_trigger_handler, NULL); + if (ret) + goto err_vref_n_disable; + + ret = iio_device_register(indio_dev); + if (ret) + goto err_buffer_cleanup; + + return 0; +err_buffer_cleanup: + iio_triggered_buffer_cleanup(indio_dev); +err_vref_n_disable: + if (!IS_ERR(adc->vref_n)) + regulator_disable(adc->vref_n); +err_vref_p_disable: + regulator_disable(adc->vref_p); +err_clk_disable: + clk_disable_unprepare(adc->cclk); + + return ret; +} + +static int adc12138_remove(struct spi_device *spi) +{ + struct iio_dev *indio_dev = spi_get_drvdata(spi); + struct adc12138 *adc = iio_priv(indio_dev); + + iio_device_unregister(indio_dev); + iio_triggered_buffer_cleanup(indio_dev); + if (!IS_ERR(adc->vref_n)) + regulator_disable(adc->vref_n); + regulator_disable(adc->vref_p); + clk_disable_unprepare(adc->cclk); + + return 0; +} + +#ifdef CONFIG_OF + +static const struct of_device_id adc12138_dt_ids[] = { + { .compatible = "ti,adc12130", }, + { .compatible = "ti,adc12132", }, + { .compatible = "ti,adc12138", }, + {} +}; +MODULE_DEVICE_TABLE(of, adc12138_dt_ids); + +#endif + +static const struct spi_device_id adc12138_id[] = { + { "adc12130", adc12130 }, + { "adc12132", adc12132 }, + { "adc12138", adc12138 }, + {} +}; +MODULE_DEVICE_TABLE(spi, adc12138_id); + +static struct spi_driver adc12138_driver = { + .driver = { + .name = "adc12138", + .of_match_table = of_match_ptr(adc12138_dt_ids), + }, + .probe = adc12138_probe, + .remove = adc12138_remove, + .id_table = adc12138_id, +}; +module_spi_driver(adc12138_driver); + +MODULE_AUTHOR("Akinobu Mita "); +MODULE_DESCRIPTION("ADC12130/ADC12132/ADC12138 driver"); +MODULE_LICENSE("GPL v2"); -- cgit v1.2.3 From a5c8b11a361065db028721c62aa880bfe0736aa6 Mon Sep 17 00:00:00 2001 From: Christoph Fritz Date: Sat, 3 Sep 2016 12:30:00 +0200 Subject: iio: sx9500: add final devicetree support This makes sx9500 driver usable on devicetree based platforms too. Signed-off-by: Christoph Fritz Reviewed-by: Fabio Estevam Reviewed-by: Vlad Dogaru Signed-off-by: Jonathan Cameron --- .../devicetree/bindings/iio/proximity/sx9500.txt | 24 ++++++++++++++++++++++ drivers/iio/proximity/sx9500.c | 7 +++++++ 2 files changed, 31 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/proximity/sx9500.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/iio/proximity/sx9500.txt b/Documentation/devicetree/bindings/iio/proximity/sx9500.txt new file mode 100644 index 000000000000..b301dd2b35da --- /dev/null +++ b/Documentation/devicetree/bindings/iio/proximity/sx9500.txt @@ -0,0 +1,24 @@ +Semtech's SX9500 capacitive proximity button device driver + +Required properties: + - compatible: must be "semtech,sx9500" + - reg: i2c address where to find the device + - interrupt-parent : should be the phandle for the interrupt controller + - interrupts : the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic + interrupt client node bindings. + +Optional properties: + - reset-gpios: Reference to the GPIO connected to the device's active + low reset pin. + +Example: + +sx9500@28 { + compatible = "semtech,sx9500"; + reg = <0x28>; + interrupt-parent = <&gpio2>; + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; +}; diff --git a/drivers/iio/proximity/sx9500.c b/drivers/iio/proximity/sx9500.c index 6f84f53dfe54..1f06282ec793 100644 --- a/drivers/iio/proximity/sx9500.c +++ b/drivers/iio/proximity/sx9500.c @@ -1025,6 +1025,12 @@ static const struct acpi_device_id sx9500_acpi_match[] = { }; MODULE_DEVICE_TABLE(acpi, sx9500_acpi_match); +static const struct of_device_id sx9500_of_match[] = { + { .compatible = "semtech,sx9500", }, + { } +}; +MODULE_DEVICE_TABLE(of, sx9500_of_match); + static const struct i2c_device_id sx9500_id[] = { {"sx9500", 0}, { }, @@ -1035,6 +1041,7 @@ static struct i2c_driver sx9500_driver = { .driver = { .name = SX9500_DRIVER_NAME, .acpi_match_table = ACPI_PTR(sx9500_acpi_match), + .of_match_table = of_match_ptr(sx9500_of_match), .pm = &sx9500_pm_ops, }, .probe = sx9500_probe, -- cgit v1.2.3 From 9083325f1197a6956db17809d74dbe3578dc1005 Mon Sep 17 00:00:00 2001 From: Gregor Boirie Date: Fri, 2 Sep 2016 20:47:54 +0200 Subject: iio:trigger: add resource managed (un)register Add resource managed devm_iio_trigger_register() and devm_iio_triger_unregister() to automatically clean up registered triggers allocated by IIO drivers, thus leading to simplified IIO drivers code. Signed-off-by: Gregor Boirie Signed-off-by: Jonathan Cameron --- Documentation/driver-model/devres.txt | 2 ++ drivers/iio/industrialio-trigger.c | 59 +++++++++++++++++++++++++++++++++++ include/linux/iio/trigger.h | 6 ++++ 3 files changed, 67 insertions(+) (limited to 'Documentation') diff --git a/Documentation/driver-model/devres.txt b/Documentation/driver-model/devres.txt index b0d775d28e97..6a2138a7c3ff 100644 --- a/Documentation/driver-model/devres.txt +++ b/Documentation/driver-model/devres.txt @@ -268,6 +268,8 @@ IIO devm_iio_kfifo_free() devm_iio_trigger_alloc() devm_iio_trigger_free() + devm_iio_trigger_register() + devm_iio_trigger_unregister() devm_iio_channel_get() devm_iio_channel_release() devm_iio_channel_get_all() diff --git a/drivers/iio/industrialio-trigger.c b/drivers/iio/industrialio-trigger.c index 3dde81e57e97..ba584b5e71f4 100644 --- a/drivers/iio/industrialio-trigger.c +++ b/drivers/iio/industrialio-trigger.c @@ -642,6 +642,65 @@ void devm_iio_trigger_free(struct device *dev, struct iio_trigger *iio_trig) } EXPORT_SYMBOL_GPL(devm_iio_trigger_free); +static void devm_iio_trigger_unreg(struct device *dev, void *res) +{ + iio_trigger_unregister(*(struct iio_trigger **)res); +} + +/** + * devm_iio_trigger_register - Resource-managed iio_trigger_register() + * @dev: device this trigger was allocated for + * @trig_info: trigger to register + * + * Managed iio_trigger_register(). The IIO trigger registered with this + * function is automatically unregistered on driver detach. This function + * calls iio_trigger_register() internally. Refer to that function for more + * information. + * + * If an iio_trigger registered with this function needs to be unregistered + * separately, devm_iio_trigger_unregister() must be used. + * + * RETURNS: + * 0 on success, negative error number on failure. + */ +int devm_iio_trigger_register(struct device *dev, struct iio_trigger *trig_info) +{ + struct iio_trigger **ptr; + int ret; + + ptr = devres_alloc(devm_iio_trigger_unreg, sizeof(*ptr), GFP_KERNEL); + if (!ptr) + return -ENOMEM; + + *ptr = trig_info; + ret = iio_trigger_register(trig_info); + if (!ret) + devres_add(dev, ptr); + else + devres_free(ptr); + + return ret; +} +EXPORT_SYMBOL_GPL(devm_iio_trigger_register); + +/** + * devm_iio_trigger_unregister - Resource-managed iio_trigger_unregister() + * @dev: device this iio_trigger belongs to + * @trig_info: the trigger associated with the device + * + * Unregister trigger registered with devm_iio_trigger_register(). + */ +void devm_iio_trigger_unregister(struct device *dev, + struct iio_trigger *trig_info) +{ + int rc; + + rc = devres_release(dev, devm_iio_trigger_unreg, devm_iio_trigger_match, + trig_info); + WARN_ON(rc); +} +EXPORT_SYMBOL_GPL(devm_iio_trigger_unregister); + void iio_device_register_trigger_consumer(struct iio_dev *indio_dev) { indio_dev->groups[indio_dev->groupcounter++] = diff --git a/include/linux/iio/trigger.h b/include/linux/iio/trigger.h index a122bdd4076c..f0890a5abf13 100644 --- a/include/linux/iio/trigger.h +++ b/include/linux/iio/trigger.h @@ -125,12 +125,18 @@ static inline void *iio_trigger_get_drvdata(struct iio_trigger *trig) **/ int iio_trigger_register(struct iio_trigger *trig_info); +int devm_iio_trigger_register(struct device *dev, + struct iio_trigger *trig_info); + /** * iio_trigger_unregister() - unregister a trigger from the core * @trig_info: trigger to be unregistered **/ void iio_trigger_unregister(struct iio_trigger *trig_info); +void devm_iio_trigger_unregister(struct device *dev, + struct iio_trigger *trig_info); + /** * iio_trigger_set_immutable() - set an immutable trigger on destination * -- cgit v1.2.3 From 70e483487db787b152da756d4be0fef917378142 Mon Sep 17 00:00:00 2001 From: Gregor Boirie Date: Fri, 2 Sep 2016 20:47:55 +0200 Subject: iio: add resource managed triggered buffer init helpers Add resource managed devm_iio_triggered_buffer_setup() and devm_iio_triggered_buffer_cleanup() to automatically clean up triggered buffers setup by IIO drivers, thus leading to simplified IIO drivers code. Signed-off-by: Gregor Boirie Signed-off-by: Jonathan Cameron --- Documentation/driver-model/devres.txt | 2 ++ drivers/iio/buffer/industrialio-triggered-buffer.c | 42 ++++++++++++++++++++++ drivers/iio/industrialio-core.c | 3 +- include/linux/iio/iio.h | 1 + include/linux/iio/triggered_buffer.h | 8 +++++ 5 files changed, 55 insertions(+), 1 deletion(-) (limited to 'Documentation') diff --git a/Documentation/driver-model/devres.txt b/Documentation/driver-model/devres.txt index 6a2138a7c3ff..75bc5b8add2f 100644 --- a/Documentation/driver-model/devres.txt +++ b/Documentation/driver-model/devres.txt @@ -266,6 +266,8 @@ IIO devm_iio_device_unregister() devm_iio_kfifo_allocate() devm_iio_kfifo_free() + devm_iio_triggered_buffer_setup() + devm_iio_triggered_buffer_cleanup() devm_iio_trigger_alloc() devm_iio_trigger_free() devm_iio_trigger_register() diff --git a/drivers/iio/buffer/industrialio-triggered-buffer.c b/drivers/iio/buffer/industrialio-triggered-buffer.c index 4b2858ba1fd6..d3db1fce54d2 100644 --- a/drivers/iio/buffer/industrialio-triggered-buffer.c +++ b/drivers/iio/buffer/industrialio-triggered-buffer.c @@ -98,6 +98,48 @@ void iio_triggered_buffer_cleanup(struct iio_dev *indio_dev) } EXPORT_SYMBOL(iio_triggered_buffer_cleanup); +static void devm_iio_triggered_buffer_clean(struct device *dev, void *res) +{ + iio_triggered_buffer_cleanup(*(struct iio_dev **)res); +} + +int devm_iio_triggered_buffer_setup(struct device *dev, + struct iio_dev *indio_dev, + irqreturn_t (*h)(int irq, void *p), + irqreturn_t (*thread)(int irq, void *p), + const struct iio_buffer_setup_ops *ops) +{ + struct iio_dev **ptr; + int ret; + + ptr = devres_alloc(devm_iio_triggered_buffer_clean, sizeof(*ptr), + GFP_KERNEL); + if (!ptr) + return -ENOMEM; + + *ptr = indio_dev; + + ret = iio_triggered_buffer_setup(indio_dev, h, thread, ops); + if (!ret) + devres_add(dev, ptr); + else + devres_free(ptr); + + return ret; +} +EXPORT_SYMBOL_GPL(devm_iio_triggered_buffer_setup); + +void devm_iio_triggered_buffer_cleanup(struct device *dev, + struct iio_dev *indio_dev) +{ + int rc; + + rc = devres_release(dev, devm_iio_triggered_buffer_clean, + devm_iio_device_match, indio_dev); + WARN_ON(rc); +} +EXPORT_SYMBOL_GPL(devm_iio_triggered_buffer_cleanup); + MODULE_AUTHOR("Lars-Peter Clausen "); MODULE_DESCRIPTION("IIO helper functions for setting up triggered buffers"); MODULE_LICENSE("GPL"); diff --git a/drivers/iio/industrialio-core.c b/drivers/iio/industrialio-core.c index f914d5d140e4..0528a0c1b964 100644 --- a/drivers/iio/industrialio-core.c +++ b/drivers/iio/industrialio-core.c @@ -1309,7 +1309,7 @@ static void devm_iio_device_release(struct device *dev, void *res) iio_device_free(*(struct iio_dev **)res); } -static int devm_iio_device_match(struct device *dev, void *res, void *data) +int devm_iio_device_match(struct device *dev, void *res, void *data) { struct iio_dev **r = res; if (!r || !*r) { @@ -1318,6 +1318,7 @@ static int devm_iio_device_match(struct device *dev, void *res, void *data) } return *r == data; } +EXPORT_SYMBOL_GPL(devm_iio_device_match); /** * devm_iio_device_alloc - Resource-managed iio_device_alloc() diff --git a/include/linux/iio/iio.h b/include/linux/iio/iio.h index 786952cd509f..b4a0679e4a49 100644 --- a/include/linux/iio/iio.h +++ b/include/linux/iio/iio.h @@ -644,6 +644,7 @@ static inline struct iio_dev *iio_priv_to_dev(void *priv) } void iio_device_free(struct iio_dev *indio_dev); +int devm_iio_device_match(struct device *dev, void *res, void *data); struct iio_dev *devm_iio_device_alloc(struct device *dev, int sizeof_priv); void devm_iio_device_free(struct device *dev, struct iio_dev *indio_dev); struct iio_trigger *devm_iio_trigger_alloc(struct device *dev, diff --git a/include/linux/iio/triggered_buffer.h b/include/linux/iio/triggered_buffer.h index f72f70d5a97b..30145616773d 100644 --- a/include/linux/iio/triggered_buffer.h +++ b/include/linux/iio/triggered_buffer.h @@ -12,4 +12,12 @@ int iio_triggered_buffer_setup(struct iio_dev *indio_dev, const struct iio_buffer_setup_ops *setup_ops); void iio_triggered_buffer_cleanup(struct iio_dev *indio_dev); +int devm_iio_triggered_buffer_setup(struct device *dev, + struct iio_dev *indio_dev, + irqreturn_t (*h)(int irq, void *p), + irqreturn_t (*thread)(int irq, void *p), + const struct iio_buffer_setup_ops *ops); +void devm_iio_triggered_buffer_cleanup(struct device *dev, + struct iio_dev *indio_dev); + #endif -- cgit v1.2.3 From 063e3303a93fcd64554730145361f102236724cb Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Mon, 12 Sep 2016 09:43:50 +0200 Subject: iio: accel: Add driver for the mCube MC3230 3-axis accelerometer Add an IIO driver for the mCube MC3230 3-axis accelerometer. A datasheet for the mCube MC3230 can be found here: http://www.mcubemems.com/wp-content/uploads/2014/10/MC3230_2-Datasheet-APS-048-0007v1.6.pdf Signed-off-by: Hans de Goede Signed-off-by: Jonathan Cameron --- .../devicetree/bindings/i2c/trivial-devices.txt | 1 + drivers/iio/accel/Kconfig | 10 + drivers/iio/accel/Makefile | 1 + drivers/iio/accel/mc3230.c | 211 +++++++++++++++++++++ 4 files changed, 223 insertions(+) create mode 100644 drivers/iio/accel/mc3230.c (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 310b1bbef5fc..1416c6a0d2cd 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -57,6 +57,7 @@ maxim,ds1050 5 Bit Programmable, Pulse-Width Modulator maxim,max1237 Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface mc,rv3029c2 Real Time Clock Module with I2C-Bus +mcube,mc3230 mCube 3-axis 8-bit digital accelerometer microchip,mcp4531-502 Microchip 7-bit Single I2C Digital Potentiometer (5k) microchip,mcp4531-103 Microchip 7-bit Single I2C Digital Potentiometer (10k) microchip,mcp4531-503 Microchip 7-bit Single I2C Digital Potentiometer (50k) diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig index a8e9ed47bbb4..2b791fe1e2bc 100644 --- a/drivers/iio/accel/Kconfig +++ b/drivers/iio/accel/Kconfig @@ -161,6 +161,16 @@ config KXCJK1013 To compile this driver as a module, choose M here: the module will be called kxcjk-1013. +config MC3230 + tristate "mCube MC3230 Digital Accelerometer Driver" + depends on I2C + help + Say yes here to build support for the mCube MC3230 low-g tri-axial + digital accelerometer. + + To compile this driver as a module, choose M here: the + module will be called mc3230. + config MMA7455 tristate select IIO_BUFFER diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile index b5c2a0b5550f..f5d3ddee619e 100644 --- a/drivers/iio/accel/Makefile +++ b/drivers/iio/accel/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_KXCJK1013) += kxcjk-1013.o obj-$(CONFIG_KXSD9) += kxsd9.o obj-$(CONFIG_KXSD9_SPI) += kxsd9-spi.o obj-$(CONFIG_KXSD9_I2C) += kxsd9-i2c.o +obj-$(CONFIG_MC3230) += mc3230.o obj-$(CONFIG_MMA7455) += mma7455_core.o obj-$(CONFIG_MMA7455_I2C) += mma7455_i2c.o diff --git a/drivers/iio/accel/mc3230.c b/drivers/iio/accel/mc3230.c new file mode 100644 index 000000000000..4ea2ff623a6d --- /dev/null +++ b/drivers/iio/accel/mc3230.c @@ -0,0 +1,211 @@ +/** + * mCube MC3230 3-Axis Accelerometer + * + * Copyright (c) 2016 Hans de Goede + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * IIO driver for mCube MC3230; 7-bit I2C address: 0x4c. + */ + +#include +#include +#include +#include + +#define MC3230_REG_XOUT 0x00 +#define MC3230_REG_YOUT 0x01 +#define MC3230_REG_ZOUT 0x02 + +#define MC3230_REG_MODE 0x07 +#define MC3230_MODE_OPCON_MASK 0x03 +#define MC3230_MODE_OPCON_WAKE 0x01 +#define MC3230_MODE_OPCON_STANDBY 0x03 + +#define MC3230_REG_CHIP_ID 0x18 +#define MC3230_CHIP_ID 0x01 + +#define MC3230_REG_PRODUCT_CODE 0x3b +#define MC3230_PRODUCT_CODE 0x19 + +/* + * The accelerometer has one measurement range: + * + * -1.5g - +1.5g (8-bit, signed) + * + * scale = (1.5 + 1.5) * 9.81 / (2^8 - 1) = 0.115411765 + */ + +static const int mc3230_nscale = 115411765; + +#define MC3230_CHANNEL(reg, axis) { \ + .type = IIO_ACCEL, \ + .address = reg, \ + .modified = 1, \ + .channel2 = IIO_MOD_##axis, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ +} + +static const struct iio_chan_spec mc3230_channels[] = { + MC3230_CHANNEL(MC3230_REG_XOUT, X), + MC3230_CHANNEL(MC3230_REG_YOUT, Y), + MC3230_CHANNEL(MC3230_REG_ZOUT, Z), +}; + +struct mc3230_data { + struct i2c_client *client; +}; + +static int mc3230_set_opcon(struct mc3230_data *data, int opcon) +{ + int ret; + struct i2c_client *client = data->client; + + ret = i2c_smbus_read_byte_data(client, MC3230_REG_MODE); + if (ret < 0) { + dev_err(&client->dev, "failed to read mode reg: %d\n", ret); + return ret; + } + + ret &= ~MC3230_MODE_OPCON_MASK; + ret |= opcon; + + ret = i2c_smbus_write_byte_data(client, MC3230_REG_MODE, ret); + if (ret < 0) { + dev_err(&client->dev, "failed to write mode reg: %d\n", ret); + return ret; + } + + return 0; +} + +static int mc3230_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, long mask) +{ + struct mc3230_data *data = iio_priv(indio_dev); + int ret; + + switch (mask) { + case IIO_CHAN_INFO_RAW: + ret = i2c_smbus_read_byte_data(data->client, chan->address); + if (ret < 0) + return ret; + *val = sign_extend32(ret, 7); + return IIO_VAL_INT; + case IIO_CHAN_INFO_SCALE: + *val = 0; + *val2 = mc3230_nscale; + return IIO_VAL_INT_PLUS_NANO; + default: + return -EINVAL; + } +} + +static const struct iio_info mc3230_info = { + .driver_module = THIS_MODULE, + .read_raw = mc3230_read_raw, +}; + +static int mc3230_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + int ret; + struct iio_dev *indio_dev; + struct mc3230_data *data; + + /* First check chip-id and product-id */ + ret = i2c_smbus_read_byte_data(client, MC3230_REG_CHIP_ID); + if (ret != MC3230_CHIP_ID) + return (ret < 0) ? ret : -ENODEV; + + ret = i2c_smbus_read_byte_data(client, MC3230_REG_PRODUCT_CODE); + if (ret != MC3230_PRODUCT_CODE) + return (ret < 0) ? ret : -ENODEV; + + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); + if (!indio_dev) { + dev_err(&client->dev, "iio allocation failed!\n"); + return -ENOMEM; + } + + data = iio_priv(indio_dev); + data->client = client; + i2c_set_clientdata(client, indio_dev); + + indio_dev->dev.parent = &client->dev; + indio_dev->info = &mc3230_info; + indio_dev->name = "mc3230"; + indio_dev->modes = INDIO_DIRECT_MODE; + indio_dev->channels = mc3230_channels; + indio_dev->num_channels = ARRAY_SIZE(mc3230_channels); + + ret = mc3230_set_opcon(data, MC3230_MODE_OPCON_WAKE); + if (ret < 0) + return ret; + + ret = iio_device_register(indio_dev); + if (ret < 0) { + dev_err(&client->dev, "device_register failed\n"); + mc3230_set_opcon(data, MC3230_MODE_OPCON_STANDBY); + } + + return ret; +} + +static int mc3230_remove(struct i2c_client *client) +{ + struct iio_dev *indio_dev = i2c_get_clientdata(client); + + iio_device_unregister(indio_dev); + + return mc3230_set_opcon(iio_priv(indio_dev), MC3230_MODE_OPCON_STANDBY); +} + +#ifdef CONFIG_PM_SLEEP +static int mc3230_suspend(struct device *dev) +{ + struct mc3230_data *data; + + data = iio_priv(i2c_get_clientdata(to_i2c_client(dev))); + + return mc3230_set_opcon(data, MC3230_MODE_OPCON_STANDBY); +} + +static int mc3230_resume(struct device *dev) +{ + struct mc3230_data *data; + + data = iio_priv(i2c_get_clientdata(to_i2c_client(dev))); + + return mc3230_set_opcon(data, MC3230_MODE_OPCON_WAKE); +} +#endif + +static SIMPLE_DEV_PM_OPS(mc3230_pm_ops, mc3230_suspend, mc3230_resume); + +static const struct i2c_device_id mc3230_i2c_id[] = { + {"mc3230", 0}, + {} +}; +MODULE_DEVICE_TABLE(i2c, mc3230_i2c_id); + +static struct i2c_driver mc3230_driver = { + .driver = { + .name = "mc3230", + .pm = &mc3230_pm_ops, + }, + .probe = mc3230_probe, + .remove = mc3230_remove, + .id_table = mc3230_i2c_id, +}; + +module_i2c_driver(mc3230_driver); + +MODULE_AUTHOR("Hans de Goede "); +MODULE_DESCRIPTION("mCube MC3230 3-Axis Accelerometer driver"); +MODULE_LICENSE("GPL v2"); -- cgit v1.2.3 From 03b262f2bbf43b82eaef82ffb3bc671d5b5c8da1 Mon Sep 17 00:00:00 2001 From: Gregor Boirie Date: Tue, 13 Sep 2016 14:23:14 +0200 Subject: iio:pressure: initial zpa2326 barometer support Introduce driver for Murata ZPA2326 pressure and temperature sensor: http://www.murata.com/en-us/products/productdetail?partno=ZPA2326-0311A-R Signed-off-by: Gregor Boirie Signed-off-by: Jonathan Cameron --- .../devicetree/bindings/iio/pressure/zpa2326.txt | 31 + drivers/iio/pressure/Kconfig | 22 + drivers/iio/pressure/Makefile | 3 + drivers/iio/pressure/zpa2326.c | 1735 ++++++++++++++++++++ drivers/iio/pressure/zpa2326.h | 89 + drivers/iio/pressure/zpa2326_i2c.c | 99 ++ drivers/iio/pressure/zpa2326_spi.c | 103 ++ 7 files changed, 2082 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/pressure/zpa2326.txt create mode 100644 drivers/iio/pressure/zpa2326.c create mode 100644 drivers/iio/pressure/zpa2326.h create mode 100644 drivers/iio/pressure/zpa2326_i2c.c create mode 100644 drivers/iio/pressure/zpa2326_spi.c (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/iio/pressure/zpa2326.txt b/Documentation/devicetree/bindings/iio/pressure/zpa2326.txt new file mode 100644 index 000000000000..fb85de676e03 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/zpa2326.txt @@ -0,0 +1,31 @@ +Murata ZPA2326 pressure sensor + +Pressure sensor from Murata with SPI and I2C bus interfaces. + +Required properties: +- compatible: "murata,zpa2326" +- reg: the I2C address or SPI chip select the device will respond to + +Recommended properties for SPI bus usage: +- spi-max-frequency: maximum SPI bus frequency as documented in + Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: +- vref-supply: an optional regulator that needs to be on to provide VREF + power to the sensor +- vdd-supply: an optional regulator that needs to be on to provide VDD + power to the sensor +- interrupt-parent: phandle to the parent interrupt controller as documented in + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +- interrupts: interrupt mapping for IRQ as documented in + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Example: + +zpa2326@5c { + compatible = "murata,zpa2326"; + reg = <0x5c>; + interrupt-parent = <&gpio>; + interrupts = <12>; + vdd-supply = <&ldo_1v8_gnss>; +}; diff --git a/drivers/iio/pressure/Kconfig b/drivers/iio/pressure/Kconfig index d130cdc78f43..cc090d803465 100644 --- a/drivers/iio/pressure/Kconfig +++ b/drivers/iio/pressure/Kconfig @@ -187,4 +187,26 @@ config HP206C This driver can also be built as a module. If so, the module will be called hp206c. +config ZPA2326 + tristate "Murata ZPA2326 pressure sensor driver" + select IIO_BUFFER + select IIO_TRIGGERED_BUFFER + select REGMAP + select ZPA2326_I2C if I2C + select ZPA2326_SPI if SPI_MASTER + help + Say Y here to build support for the Murata ZPA2326 pressure and + temperature sensor. + + To compile this driver as a module, choose M here: the module will + be called zpa2326. + +config ZPA2326_I2C + tristate + select REGMAP_I2C + +config ZPA2326_SPI + tristate + select REGMAP_SPI + endmenu diff --git a/drivers/iio/pressure/Makefile b/drivers/iio/pressure/Makefile index 7f395bed5e88..fff77185a5cc 100644 --- a/drivers/iio/pressure/Makefile +++ b/drivers/iio/pressure/Makefile @@ -22,6 +22,9 @@ st_pressure-y := st_pressure_core.o st_pressure-$(CONFIG_IIO_BUFFER) += st_pressure_buffer.o obj-$(CONFIG_T5403) += t5403.o obj-$(CONFIG_HP206C) += hp206c.o +obj-$(CONFIG_ZPA2326) += zpa2326.o +obj-$(CONFIG_ZPA2326_I2C) += zpa2326_i2c.o +obj-$(CONFIG_ZPA2326_SPI) += zpa2326_spi.o obj-$(CONFIG_IIO_ST_PRESS_I2C) += st_pressure_i2c.o obj-$(CONFIG_IIO_ST_PRESS_SPI) += st_pressure_spi.o diff --git a/drivers/iio/pressure/zpa2326.c b/drivers/iio/pressure/zpa2326.c new file mode 100644 index 000000000000..19d2eb46fda6 --- /dev/null +++ b/drivers/iio/pressure/zpa2326.c @@ -0,0 +1,1735 @@ +/* + * Murata ZPA2326 pressure and temperature sensor IIO driver + * + * Copyright (c) 2016 Parrot S.A. + * + * Author: Gregor Boirie + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + */ + +/** + * DOC: ZPA2326 theory of operations + * + * This driver supports %INDIO_DIRECT_MODE and %INDIO_BUFFER_TRIGGERED IIO + * modes. + * A internal hardware trigger is also implemented to dispatch registered IIO + * trigger consumers upon "sample ready" interrupts. + * + * ZPA2326 hardware supports 2 sampling mode: one shot and continuous. + * + * A complete one shot sampling cycle gets device out of low power mode, + * performs pressure and temperature measurements, then automatically switches + * back to low power mode. It is meant for on demand sampling with optimal power + * saving at the cost of lower sampling rate and higher software overhead. + * This is a natural candidate for IIO read_raw hook implementation + * (%INDIO_DIRECT_MODE). It is also used for triggered buffering support to + * ensure explicit synchronization with external trigger events + * (%INDIO_BUFFER_TRIGGERED). + * + * The continuous mode works according to a periodic hardware measurement + * process continuously pushing samples into an internal hardware FIFO (for + * pressure samples only). Measurement cycle completion may be signaled by a + * "sample ready" interrupt. + * Typical software sequence of operations : + * - get device out of low power mode, + * - setup hardware sampling period, + * - at end of period, upon data ready interrupt: pop pressure samples out of + * hardware FIFO and fetch temperature sample + * - when no longer needed, stop sampling process by putting device into + * low power mode. + * This mode is used to implement %INDIO_BUFFER_TRIGGERED mode if device tree + * declares a valid interrupt line. In this case, the internal hardware trigger + * drives acquisition. + * + * Note that hardware sampling frequency is taken into account only when + * internal hardware trigger is attached as the highest sampling rate seems to + * be the most energy efficient. + * + * TODO: + * preset pressure threshold crossing / IIO events ; + * differential pressure sampling ; + * hardware samples averaging. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "zpa2326.h" + +/* 200 ms should be enough for the longest conversion time in one-shot mode. */ +#define ZPA2326_CONVERSION_JIFFIES (HZ / 5) + +/* There should be a 1 ms delay (Tpup) after getting out of reset. */ +#define ZPA2326_TPUP_USEC_MIN (1000) +#define ZPA2326_TPUP_USEC_MAX (2000) + +/** + * struct zpa2326_frequency - Hardware sampling frequency descriptor + * @hz : Frequency in Hertz. + * @odr: Output Data Rate word as expected by %ZPA2326_CTRL_REG3_REG. + */ +struct zpa2326_frequency { + int hz; + u16 odr; +}; + +/* + * Keep these in strict ascending order: last array entry is expected to + * correspond to the highest sampling frequency. + */ +static const struct zpa2326_frequency zpa2326_sampling_frequencies[] = { + { .hz = 1, .odr = 1 << ZPA2326_CTRL_REG3_ODR_SHIFT }, + { .hz = 5, .odr = 5 << ZPA2326_CTRL_REG3_ODR_SHIFT }, + { .hz = 11, .odr = 6 << ZPA2326_CTRL_REG3_ODR_SHIFT }, + { .hz = 23, .odr = 7 << ZPA2326_CTRL_REG3_ODR_SHIFT }, +}; + +/* Return the highest hardware sampling frequency available. */ +static const struct zpa2326_frequency *zpa2326_highest_frequency(void) +{ + return &zpa2326_sampling_frequencies[ + ARRAY_SIZE(zpa2326_sampling_frequencies) - 1]; +} + +/** + * struct zpa_private - Per-device internal private state + * @timestamp: Buffered samples ready datum. + * @regmap: Underlying I2C / SPI bus adapter used to abstract slave register + * accesses. + * @result: Allows sampling logic to get completion status of operations + * that interrupt handlers perform asynchronously. + * @data_ready: Interrupt handler uses this to wake user context up at sampling + * operation completion. + * @trigger: Optional hardware / interrupt driven trigger used to notify + * external devices a new sample is ready. + * @waken: Flag indicating whether or not device has just been powered on. + * @irq: Optional interrupt line: negative or zero if not declared into + * DT, in which case sampling logic keeps polling status register + * to detect completion. + * @frequency: Current hardware sampling frequency. + * @vref: Power / voltage reference. + * @vdd: Power supply. + */ +struct zpa2326_private { + s64 timestamp; + struct regmap *regmap; + int result; + struct completion data_ready; + struct iio_trigger *trigger; + bool waken; + int irq; + const struct zpa2326_frequency *frequency; + struct regulator *vref; + struct regulator *vdd; +}; + +#define zpa2326_err(_idev, _format, _arg...) \ + dev_err(_idev->dev.parent, _format, ##_arg) + +#define zpa2326_warn(_idev, _format, _arg...) \ + dev_warn(_idev->dev.parent, _format, ##_arg) + +#ifdef DEBUG +#define zpa2326_dbg(_idev, _format, _arg...) \ + dev_dbg(_idev->dev.parent, _format, ##_arg) +#else +#define zpa2326_dbg(_idev, _format, _arg...) +#endif + +bool zpa2326_isreg_writeable(struct device *dev, unsigned int reg) +{ + switch (reg) { + case ZPA2326_REF_P_XL_REG: + case ZPA2326_REF_P_L_REG: + case ZPA2326_REF_P_H_REG: + case ZPA2326_RES_CONF_REG: + case ZPA2326_CTRL_REG0_REG: + case ZPA2326_CTRL_REG1_REG: + case ZPA2326_CTRL_REG2_REG: + case ZPA2326_CTRL_REG3_REG: + case ZPA2326_THS_P_LOW_REG: + case ZPA2326_THS_P_HIGH_REG: + return true; + + default: + return false; + } +} +EXPORT_SYMBOL_GPL(zpa2326_isreg_writeable); + +bool zpa2326_isreg_readable(struct device *dev, unsigned int reg) +{ + switch (reg) { + case ZPA2326_REF_P_XL_REG: + case ZPA2326_REF_P_L_REG: + case ZPA2326_REF_P_H_REG: + case ZPA2326_DEVICE_ID_REG: + case ZPA2326_RES_CONF_REG: + case ZPA2326_CTRL_REG0_REG: + case ZPA2326_CTRL_REG1_REG: + case ZPA2326_CTRL_REG2_REG: + case ZPA2326_CTRL_REG3_REG: + case ZPA2326_INT_SOURCE_REG: + case ZPA2326_THS_P_LOW_REG: + case ZPA2326_THS_P_HIGH_REG: + case ZPA2326_STATUS_REG: + case ZPA2326_PRESS_OUT_XL_REG: + case ZPA2326_PRESS_OUT_L_REG: + case ZPA2326_PRESS_OUT_H_REG: + case ZPA2326_TEMP_OUT_L_REG: + case ZPA2326_TEMP_OUT_H_REG: + return true; + + default: + return false; + } +} +EXPORT_SYMBOL_GPL(zpa2326_isreg_readable); + +bool zpa2326_isreg_precious(struct device *dev, unsigned int reg) +{ + switch (reg) { + case ZPA2326_INT_SOURCE_REG: + case ZPA2326_PRESS_OUT_H_REG: + return true; + + default: + return false; + } +} +EXPORT_SYMBOL_GPL(zpa2326_isreg_precious); + +/** + * zpa2326_enable_device() - Enable device, i.e. get out of low power mode. + * @indio_dev: The IIO device associated with the hardware to enable. + * + * Required to access complete register space and to perform any sampling + * or control operations. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_enable_device(const struct iio_dev *indio_dev) +{ + int err; + + err = regmap_write(((struct zpa2326_private *) + iio_priv(indio_dev))->regmap, + ZPA2326_CTRL_REG0_REG, ZPA2326_CTRL_REG0_ENABLE); + if (err) { + zpa2326_err(indio_dev, "failed to enable device (%d)", err); + return err; + } + + zpa2326_dbg(indio_dev, "enabled"); + + return 0; +} + +/** + * zpa2326_sleep() - Disable device, i.e. switch to low power mode. + * @indio_dev: The IIO device associated with the hardware to disable. + * + * Only %ZPA2326_DEVICE_ID_REG and %ZPA2326_CTRL_REG0_REG registers may be + * accessed once device is in the disabled state. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_sleep(const struct iio_dev *indio_dev) +{ + int err; + + err = regmap_write(((struct zpa2326_private *) + iio_priv(indio_dev))->regmap, + ZPA2326_CTRL_REG0_REG, 0); + if (err) { + zpa2326_err(indio_dev, "failed to sleep (%d)", err); + return err; + } + + zpa2326_dbg(indio_dev, "sleeping"); + + return 0; +} + +/** + * zpa2326_reset_device() - Reset device to default hardware state. + * @indio_dev: The IIO device associated with the hardware to reset. + * + * Disable sampling and empty hardware FIFO. + * Device must be enabled before reset, i.e. not in low power mode. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_reset_device(const struct iio_dev *indio_dev) +{ + int err; + + err = regmap_write(((struct zpa2326_private *) + iio_priv(indio_dev))->regmap, + ZPA2326_CTRL_REG2_REG, ZPA2326_CTRL_REG2_SWRESET); + if (err) { + zpa2326_err(indio_dev, "failed to reset device (%d)", err); + return err; + } + + usleep_range(ZPA2326_TPUP_USEC_MIN, ZPA2326_TPUP_USEC_MAX); + + zpa2326_dbg(indio_dev, "reset"); + + return 0; +} + +/** + * zpa2326_start_oneshot() - Start a single sampling cycle, i.e. in one shot + * mode. + * @indio_dev: The IIO device associated with the sampling hardware. + * + * Device must have been previously enabled and configured for one shot mode. + * Device will be switched back to low power mode at end of cycle. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_start_oneshot(const struct iio_dev *indio_dev) +{ + int err; + + err = regmap_write(((struct zpa2326_private *) + iio_priv(indio_dev))->regmap, + ZPA2326_CTRL_REG0_REG, + ZPA2326_CTRL_REG0_ENABLE | + ZPA2326_CTRL_REG0_ONE_SHOT); + if (err) { + zpa2326_err(indio_dev, "failed to start one shot cycle (%d)", + err); + return err; + } + + zpa2326_dbg(indio_dev, "one shot cycle started"); + + return 0; +} + +/** + * zpa2326_power_on() - Power on device to allow subsequent configuration. + * @indio_dev: The IIO device associated with the sampling hardware. + * @private: Internal private state related to @indio_dev. + * + * Sampling will be disabled, preventing strange things from happening in our + * back. Hardware FIFO content will be cleared. + * When successful, device will be left in the enabled state to allow further + * configuration. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_power_on(const struct iio_dev *indio_dev, + const struct zpa2326_private *private) +{ + int err; + + err = regulator_enable(private->vref); + if (err) + return err; + + err = regulator_enable(private->vdd); + if (err) + goto vref; + + zpa2326_dbg(indio_dev, "powered on"); + + err = zpa2326_enable_device(indio_dev); + if (err) + goto vdd; + + err = zpa2326_reset_device(indio_dev); + if (err) + goto sleep; + + return 0; + +sleep: + zpa2326_sleep(indio_dev); +vdd: + regulator_disable(private->vdd); +vref: + regulator_disable(private->vref); + + zpa2326_dbg(indio_dev, "powered off"); + + return err; +} + +/** + * zpa2326_power_off() - Power off device, i.e. disable attached power + * regulators. + * @indio_dev: The IIO device associated with the sampling hardware. + * @private: Internal private state related to @indio_dev. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static void zpa2326_power_off(const struct iio_dev *indio_dev, + const struct zpa2326_private *private) +{ + regulator_disable(private->vdd); + regulator_disable(private->vref); + + zpa2326_dbg(indio_dev, "powered off"); +} + +/** + * zpa2326_config_oneshot() - Setup device for one shot / on demand mode. + * @indio_dev: The IIO device associated with the sampling hardware. + * @irq: Optional interrupt line the hardware uses to notify new data + * samples are ready. Negative or zero values indicate no interrupts + * are available, meaning polling is required. + * + * Output Data Rate is configured for the highest possible rate so that + * conversion time and power consumption are reduced to a minimum. + * Note that hardware internal averaging machinery (not implemented in this + * driver) is not applicable in this mode. + * + * Device must have been previously enabled before calling + * zpa2326_config_oneshot(). + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_config_oneshot(const struct iio_dev *indio_dev, + int irq) +{ + struct regmap *regs = ((struct zpa2326_private *) + iio_priv(indio_dev))->regmap; + const struct zpa2326_frequency *freq = zpa2326_highest_frequency(); + int err; + + /* Setup highest available Output Data Rate for one shot mode. */ + err = regmap_write(regs, ZPA2326_CTRL_REG3_REG, freq->odr); + if (err) + return err; + + if (irq > 0) { + /* Request interrupt when new sample is available. */ + err = regmap_write(regs, ZPA2326_CTRL_REG1_REG, + (u8)~ZPA2326_CTRL_REG1_MASK_DATA_READY); + + if (err) { + dev_err(indio_dev->dev.parent, + "failed to setup one shot mode (%d)", err); + return err; + } + } + + zpa2326_dbg(indio_dev, "one shot mode setup @%dHz", freq->hz); + + return 0; +} + +/** + * zpa2326_clear_fifo() - Clear remaining entries in hardware FIFO. + * @indio_dev: The IIO device associated with the sampling hardware. + * @min_count: Number of samples present within hardware FIFO. + * + * @min_count argument is a hint corresponding to the known minimum number of + * samples currently living in the FIFO. This allows to reduce the number of bus + * accesses by skipping status register read operation as long as we know for + * sure there are still entries left. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_clear_fifo(const struct iio_dev *indio_dev, + unsigned int min_count) +{ + struct regmap *regs = ((struct zpa2326_private *) + iio_priv(indio_dev))->regmap; + int err; + unsigned int val; + + if (!min_count) { + /* + * No hint: read status register to determine whether FIFO is + * empty or not. + */ + err = regmap_read(regs, ZPA2326_STATUS_REG, &val); + + if (err < 0) + goto err; + + if (val & ZPA2326_STATUS_FIFO_E) + /* Fifo is empty: nothing to trash. */ + return 0; + } + + /* Clear FIFO. */ + do { + /* + * A single fetch from pressure MSB register is enough to pop + * values out of FIFO. + */ + err = regmap_read(regs, ZPA2326_PRESS_OUT_H_REG, &val); + if (err < 0) + goto err; + + if (min_count) { + /* + * We know for sure there are at least min_count entries + * left in FIFO. Skip status register read. + */ + min_count--; + continue; + } + + err = regmap_read(regs, ZPA2326_STATUS_REG, &val); + if (err < 0) + goto err; + + } while (!(val & ZPA2326_STATUS_FIFO_E)); + + zpa2326_dbg(indio_dev, "FIFO cleared"); + + return 0; + +err: + zpa2326_err(indio_dev, "failed to clear FIFO (%d)", err); + + return err; +} + +/** + * zpa2326_dequeue_pressure() - Retrieve the most recent pressure sample from + * hardware FIFO. + * @indio_dev: The IIO device associated with the sampling hardware. + * @pressure: Sampled pressure output. + * + * Note that ZPA2326 hardware FIFO stores pressure samples only. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_dequeue_pressure(const struct iio_dev *indio_dev, + u32 *pressure) +{ + struct regmap *regs = ((struct zpa2326_private *) + iio_priv(indio_dev))->regmap; + unsigned int val; + int err; + int cleared = -1; + + err = regmap_read(regs, ZPA2326_STATUS_REG, &val); + if (err < 0) + return err; + + *pressure = 0; + + if (val & ZPA2326_STATUS_P_OR) { + /* + * Fifo overrun : first sample dequeued from FIFO is the + * newest. + */ + zpa2326_warn(indio_dev, "FIFO overflow"); + + err = regmap_bulk_read(regs, ZPA2326_PRESS_OUT_XL_REG, pressure, + 3); + if (err) + return err; + +#define ZPA2326_FIFO_DEPTH (16U) + /* Hardware FIFO may hold no more than 16 pressure samples. */ + return zpa2326_clear_fifo(indio_dev, ZPA2326_FIFO_DEPTH - 1); + } + + /* + * Fifo has not overflown : retrieve newest sample. We need to pop + * values out until FIFO is empty : last fetched pressure is the newest. + * In nominal cases, we should find a single queued sample only. + */ + do { + err = regmap_bulk_read(regs, ZPA2326_PRESS_OUT_XL_REG, pressure, + 3); + if (err) + return err; + + err = regmap_read(regs, ZPA2326_STATUS_REG, &val); + if (err < 0) + return err; + + cleared++; + } while (!(val & ZPA2326_STATUS_FIFO_E)); + + if (cleared) + /* + * Samples were pushed by hardware during previous rounds but we + * didn't consume them fast enough: inform user. + */ + zpa2326_dbg(indio_dev, "cleared %d FIFO entries", cleared); + + return 0; +} + +/** + * zpa2326_fill_sample_buffer() - Enqueue new channel samples to IIO buffer. + * @indio_dev: The IIO device associated with the sampling hardware. + * @private: Internal private state related to @indio_dev. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_fill_sample_buffer(struct iio_dev *indio_dev, + const struct zpa2326_private *private) +{ + struct { + u32 pressure; + u16 temperature; + u64 timestamp; + } sample; + int err; + + if (test_bit(0, indio_dev->active_scan_mask)) { + /* Get current pressure from hardware FIFO. */ + err = zpa2326_dequeue_pressure(indio_dev, &sample.pressure); + if (err) { + zpa2326_warn(indio_dev, "failed to fetch pressure (%d)", + err); + return err; + } + } + + if (test_bit(1, indio_dev->active_scan_mask)) { + /* Get current temperature. */ + err = regmap_bulk_read(private->regmap, ZPA2326_TEMP_OUT_L_REG, + &sample.temperature, 2); + if (err) { + zpa2326_warn(indio_dev, + "failed to fetch temperature (%d)", err); + return err; + } + } + + /* + * Now push samples using timestamp stored either : + * - by hardware interrupt handler if interrupt is available: see + * zpa2326_handle_irq(), + * - or oneshot completion polling machinery : see + * zpa2326_trigger_handler(). + */ + zpa2326_dbg(indio_dev, "filling raw samples buffer"); + + iio_push_to_buffers_with_timestamp(indio_dev, &sample, + private->timestamp); + + return 0; +} + +#ifdef CONFIG_PM +static int zpa2326_runtime_suspend(struct device *parent) +{ + const struct iio_dev *indio_dev = dev_get_drvdata(parent); + + if (pm_runtime_autosuspend_expiration(parent)) + /* Userspace changed autosuspend delay. */ + return -EAGAIN; + + zpa2326_power_off(indio_dev, iio_priv(indio_dev)); + + return 0; +} + +static int zpa2326_runtime_resume(struct device *parent) +{ + const struct iio_dev *indio_dev = dev_get_drvdata(parent); + + return zpa2326_power_on(indio_dev, iio_priv(indio_dev)); +} + +const struct dev_pm_ops zpa2326_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, + pm_runtime_force_resume) + SET_RUNTIME_PM_OPS(zpa2326_runtime_suspend, zpa2326_runtime_resume, + NULL) +}; +EXPORT_SYMBOL_GPL(zpa2326_pm_ops); + +/** + * zpa2326_resume() - Request the PM layer to power supply the device. + * @indio_dev: The IIO device associated with the sampling hardware. + * + * Return: + * < 0 - a negative error code meaning failure ; + * 0 - success, device has just been powered up ; + * 1 - success, device was already powered. + */ +static int zpa2326_resume(const struct iio_dev *indio_dev) +{ + int err; + + err = pm_runtime_get_sync(indio_dev->dev.parent); + if (err < 0) + return err; + + if (err > 0) { + /* + * Device was already power supplied: get it out of low power + * mode and inform caller. + */ + zpa2326_enable_device(indio_dev); + return 1; + } + + /* Inform caller device has just been brought back to life. */ + return 0; +} + +/** + * zpa2326_suspend() - Schedule a power down using autosuspend feature of PM + * layer. + * @indio_dev: The IIO device associated with the sampling hardware. + * + * Device is switched to low power mode at first to save power even when + * attached regulator is a "dummy" one. + */ +static void zpa2326_suspend(struct iio_dev *indio_dev) +{ + struct device *parent = indio_dev->dev.parent; + + zpa2326_sleep(indio_dev); + + pm_runtime_mark_last_busy(parent); + pm_runtime_put_autosuspend(parent); +} + +static void zpa2326_init_runtime(struct device *parent) +{ + pm_runtime_get_noresume(parent); + pm_runtime_set_active(parent); + pm_runtime_enable(parent); + pm_runtime_set_autosuspend_delay(parent, 1000); + pm_runtime_use_autosuspend(parent); + pm_runtime_mark_last_busy(parent); + pm_runtime_put_autosuspend(parent); +} + +static void zpa2326_fini_runtime(struct device *parent) +{ + pm_runtime_disable(parent); + pm_runtime_set_suspended(parent); +} +#else /* !CONFIG_PM */ +static int zpa2326_resume(const struct iio_dev *indio_dev) +{ + zpa2326_enable_device(indio_dev); + + return 0; +} + +static void zpa2326_suspend(struct iio_dev *indio_dev) +{ + zpa2326_sleep(indio_dev); +} + +#define zpa2326_init_runtime(_parent) +#define zpa2326_fini_runtime(_parent) +#endif /* !CONFIG_PM */ + +/** + * zpa2326_handle_irq() - Process hardware interrupts. + * @irq: Interrupt line the hardware uses to notify new data has arrived. + * @data: The IIO device associated with the sampling hardware. + * + * Timestamp buffered samples as soon as possible then schedule threaded bottom + * half. + * + * Return: Always successful. + */ +static irqreturn_t zpa2326_handle_irq(int irq, void *data) +{ + struct iio_dev *indio_dev = (struct iio_dev *)data; + + if (iio_buffer_enabled(indio_dev)) { + /* Timestamping needed for buffered sampling only. */ + ((struct zpa2326_private *) + iio_priv(indio_dev))->timestamp = iio_get_time_ns(indio_dev); + } + + return IRQ_WAKE_THREAD; +} + +/** + * zpa2326_handle_threaded_irq() - Interrupt bottom-half handler. + * @irq: Interrupt line the hardware uses to notify new data has arrived. + * @data: The IIO device associated with the sampling hardware. + * + * Mainly ensures interrupt is caused by a real "new sample available" + * condition. This relies upon the ability to perform blocking / sleeping bus + * accesses to slave's registers. This is why zpa2326_handle_threaded_irq() is + * called from within a thread, i.e. not called from hard interrupt context. + * + * When device is using its own internal hardware trigger in continuous sampling + * mode, data are available into hardware FIFO once interrupt has occurred. All + * we have to do is to dispatch the trigger, which in turn will fetch data and + * fill IIO buffer. + * + * When not using its own internal hardware trigger, the device has been + * configured in one-shot mode either by an external trigger or the IIO read_raw + * hook. This means one of the latter is currently waiting for sampling + * completion, in which case we must simply wake it up. + * + * See zpa2326_trigger_handler(). + * + * Return: + * %IRQ_NONE - no consistent interrupt happened ; + * %IRQ_HANDLED - there was new samples available. + */ +static irqreturn_t zpa2326_handle_threaded_irq(int irq, void *data) +{ + struct iio_dev *indio_dev = (struct iio_dev *)data; + struct zpa2326_private *priv = iio_priv(indio_dev); + unsigned int val; + bool cont; + irqreturn_t ret = IRQ_NONE; + + /* + * Are we using our own internal trigger in triggered buffer mode, i.e., + * currently working in continuous sampling mode ? + */ + cont = (iio_buffer_enabled(indio_dev) && + iio_trigger_using_own(indio_dev)); + + /* + * Device works according to a level interrupt scheme: reading interrupt + * status de-asserts interrupt line. + */ + priv->result = regmap_read(priv->regmap, ZPA2326_INT_SOURCE_REG, &val); + if (priv->result < 0) { + if (cont) + return IRQ_NONE; + + goto complete; + } + + /* Data ready is the only interrupt source we requested. */ + if (!(val & ZPA2326_INT_SOURCE_DATA_READY)) { + /* + * Interrupt happened but no new sample available: likely caused + * by spurious interrupts, in which case, returning IRQ_NONE + * allows to benefit from the generic spurious interrupts + * handling. + */ + zpa2326_warn(indio_dev, "unexpected interrupt status %02x", + val); + + if (cont) + return IRQ_NONE; + + priv->result = -ENODATA; + goto complete; + } + + /* New sample available: dispatch internal trigger consumers. */ + iio_trigger_poll_chained(priv->trigger); + + if (cont) + /* + * Internal hardware trigger has been scheduled above : it will + * fetch data on its own. + */ + return IRQ_HANDLED; + + ret = IRQ_HANDLED; + +complete: + /* + * Wake up direct or externaly triggered buffer mode waiters: see + * zpa2326_sample_oneshot() and zpa2326_trigger_handler(). + */ + complete(&priv->data_ready); + + return ret; +} + +/** + * zpa2326_wait_oneshot_completion() - Wait for oneshot data ready interrupt. + * @indio_dev: The IIO device associated with the sampling hardware. + * @private: Internal private state related to @indio_dev. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_wait_oneshot_completion(const struct iio_dev *indio_dev, + struct zpa2326_private *private) +{ + int ret; + unsigned int val; + + zpa2326_dbg(indio_dev, "waiting for one shot completion interrupt"); + + ret = wait_for_completion_interruptible_timeout( + &private->data_ready, ZPA2326_CONVERSION_JIFFIES); + if (ret > 0) + /* + * Interrupt handler completed before timeout: return operation + * status. + */ + return private->result; + + /* Clear all interrupts just to be sure. */ + regmap_read(private->regmap, ZPA2326_INT_SOURCE_REG, &val); + + if (!ret) + /* Timed out. */ + ret = -ETIME; + + if (ret != -ERESTARTSYS) + zpa2326_warn(indio_dev, "no one shot interrupt occurred (%d)", + ret); + + return ret; +} + +static int zpa2326_init_managed_irq(struct device *parent, + struct iio_dev *indio_dev, + struct zpa2326_private *private, + int irq) +{ + int err; + + private->irq = irq; + + if (irq <= 0) { + /* + * Platform declared no interrupt line: device will be polled + * for data availability. + */ + dev_info(parent, "no interrupt found, running in polling mode"); + return 0; + } + + init_completion(&private->data_ready); + + /* Request handler to be scheduled into threaded interrupt context. */ + err = devm_request_threaded_irq(parent, irq, zpa2326_handle_irq, + zpa2326_handle_threaded_irq, + IRQF_TRIGGER_RISING | IRQF_ONESHOT, + dev_name(parent), indio_dev); + if (err) { + dev_err(parent, "failed to request interrupt %d (%d)", irq, + err); + return err; + } + + dev_info(parent, "using interrupt %d", irq); + + return 0; +} + +/** + * zpa2326_poll_oneshot_completion() - Actively poll for one shot data ready. + * @indio_dev: The IIO device associated with the sampling hardware. + * + * Loop over registers content to detect end of sampling cycle. Used when DT + * declared no valid interrupt lines. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_poll_oneshot_completion(const struct iio_dev *indio_dev) +{ + unsigned long tmout = jiffies + ZPA2326_CONVERSION_JIFFIES; + struct regmap *regs = ((struct zpa2326_private *) + iio_priv(indio_dev))->regmap; + unsigned int val; + int err; + + zpa2326_dbg(indio_dev, "polling for one shot completion"); + + /* + * At least, 100 ms is needed for the device to complete its one-shot + * cycle. + */ + if (msleep_interruptible(100)) + return -ERESTARTSYS; + + /* Poll for conversion completion in hardware. */ + while (true) { + err = regmap_read(regs, ZPA2326_CTRL_REG0_REG, &val); + if (err < 0) + goto err; + + if (!(val & ZPA2326_CTRL_REG0_ONE_SHOT)) + /* One-shot bit self clears at conversion end. */ + break; + + if (time_after(jiffies, tmout)) { + /* Prevent from waiting forever : let's time out. */ + err = -ETIME; + goto err; + } + + usleep_range(10000, 20000); + } + + /* + * In oneshot mode, pressure sample availability guarantees that + * temperature conversion has also completed : just check pressure + * status bit to keep things simple. + */ + err = regmap_read(regs, ZPA2326_STATUS_REG, &val); + if (err < 0) + goto err; + + if (!(val & ZPA2326_STATUS_P_DA)) { + /* No sample available. */ + err = -ENODATA; + goto err; + } + + return 0; + +err: + zpa2326_warn(indio_dev, "failed to poll one shot completion (%d)", err); + + return err; +} + +/** + * zpa2326_fetch_raw_sample() - Retrieve a raw sample and convert it to CPU + * endianness. + * @indio_dev: The IIO device associated with the sampling hardware. + * @type: Type of measurement / channel to fetch from. + * @value: Sample output. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_fetch_raw_sample(const struct iio_dev *indio_dev, + enum iio_chan_type type, + int *value) +{ + struct regmap *regs = ((struct zpa2326_private *) + iio_priv(indio_dev))->regmap; + int err; + + switch (type) { + case IIO_PRESSURE: + zpa2326_dbg(indio_dev, "fetching raw pressure sample"); + + err = regmap_bulk_read(regs, ZPA2326_PRESS_OUT_XL_REG, value, + 3); + if (err) { + zpa2326_warn(indio_dev, "failed to fetch pressure (%d)", + err); + return err; + } + + /* Pressure is a 24 bits wide little-endian unsigned int. */ + *value = (((u8 *)value)[2] << 16) | (((u8 *)value)[1] << 8) | + ((u8 *)value)[0]; + + return IIO_VAL_INT; + + case IIO_TEMP: + zpa2326_dbg(indio_dev, "fetching raw temperature sample"); + + err = regmap_bulk_read(regs, ZPA2326_TEMP_OUT_L_REG, value, 2); + if (err) { + zpa2326_warn(indio_dev, + "failed to fetch temperature (%d)", err); + return err; + } + + /* Temperature is a 16 bits wide little-endian signed int. */ + *value = (int)le16_to_cpup((__le16 *)value); + + return IIO_VAL_INT; + + default: + return -EINVAL; + } +} + +/** + * zpa2326_sample_oneshot() - Perform a complete one shot sampling cycle. + * @indio_dev: The IIO device associated with the sampling hardware. + * @type: Type of measurement / channel to fetch from. + * @value: Sample output. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_sample_oneshot(struct iio_dev *indio_dev, + enum iio_chan_type type, + int *value) +{ + int ret; + struct zpa2326_private *priv; + + ret = iio_device_claim_direct_mode(indio_dev); + if (ret) + return ret; + + ret = zpa2326_resume(indio_dev); + if (ret < 0) + goto release; + + priv = iio_priv(indio_dev); + + if (ret > 0) { + /* + * We were already power supplied. Just clear hardware FIFO to + * get rid of samples acquired during previous rounds (if any). + * Sampling operation always generates both temperature and + * pressure samples. The latter are always enqueued into + * hardware FIFO. This may lead to situations were pressure + * samples still sit into FIFO when previous cycle(s) fetched + * temperature data only. + * Hence, we need to clear hardware FIFO content to prevent from + * getting outdated values at the end of current cycle. + */ + if (type == IIO_PRESSURE) { + ret = zpa2326_clear_fifo(indio_dev, 0); + if (ret) + goto suspend; + } + } else { + /* + * We have just been power supplied, i.e. device is in default + * "out of reset" state, meaning we need to reconfigure it + * entirely. + */ + ret = zpa2326_config_oneshot(indio_dev, priv->irq); + if (ret) + goto suspend; + } + + /* Start a sampling cycle in oneshot mode. */ + ret = zpa2326_start_oneshot(indio_dev); + if (ret) + goto suspend; + + /* Wait for sampling cycle to complete. */ + if (priv->irq > 0) + ret = zpa2326_wait_oneshot_completion(indio_dev, priv); + else + ret = zpa2326_poll_oneshot_completion(indio_dev); + + if (ret) + goto suspend; + + /* Retrieve raw sample value and convert it to CPU endianness. */ + ret = zpa2326_fetch_raw_sample(indio_dev, type, value); + +suspend: + zpa2326_suspend(indio_dev); +release: + iio_device_release_direct_mode(indio_dev); + + return ret; +} + +/** + * zpa2326_trigger_handler() - Perform an IIO buffered sampling round in one + * shot mode. + * @irq: The software interrupt assigned to @data + * @data: The IIO poll function dispatched by external trigger our device is + * attached to. + * + * Bottom-half handler called by the IIO trigger to which our device is + * currently attached. Allows us to synchronize this device buffered sampling + * either with external events (such as timer expiration, external device sample + * ready, etc...) or with its own interrupt (internal hardware trigger). + * + * When using an external trigger, basically run the same sequence of operations + * as for zpa2326_sample_oneshot() with the following hereafter. Hardware FIFO + * is not cleared since already done at buffering enable time and samples + * dequeueing always retrieves the most recent value. + * + * Otherwise, when internal hardware trigger has dispatched us, just fetch data + * from hardware FIFO. + * + * Fetched data will pushed unprocessed to IIO buffer since samples conversion + * is delegated to userspace in buffered mode (endianness, etc...). + * + * Return: + * %IRQ_NONE - no consistent interrupt happened ; + * %IRQ_HANDLED - there was new samples available. + */ +static irqreturn_t zpa2326_trigger_handler(int irq, void *data) +{ + struct iio_dev *indio_dev = ((struct iio_poll_func *) + data)->indio_dev; + struct zpa2326_private *priv = iio_priv(indio_dev); + bool cont; + + /* + * We have been dispatched, meaning we are in triggered buffer mode. + * Using our own internal trigger implies we are currently in continuous + * hardware sampling mode. + */ + cont = iio_trigger_using_own(indio_dev); + + if (!cont) { + /* On demand sampling : start a one shot cycle. */ + if (zpa2326_start_oneshot(indio_dev)) + goto out; + + /* Wait for sampling cycle to complete. */ + if (priv->irq <= 0) { + /* No interrupt available: poll for completion. */ + if (zpa2326_poll_oneshot_completion(indio_dev)) + goto out; + + /* Only timestamp sample once it is ready. */ + priv->timestamp = iio_get_time_ns(indio_dev); + } else { + /* Interrupt handlers will timestamp for us. */ + if (zpa2326_wait_oneshot_completion(indio_dev, priv)) + goto out; + } + } + + /* Enqueue to IIO buffer / userspace. */ + zpa2326_fill_sample_buffer(indio_dev, priv); + +out: + if (!cont) + /* Don't switch to low power if sampling continuously. */ + zpa2326_sleep(indio_dev); + + /* Inform attached trigger we are done. */ + iio_trigger_notify_done(indio_dev->trig); + + return IRQ_HANDLED; +} + +/** + * zpa2326_preenable_buffer() - Prepare device for configuring triggered + * sampling + * modes. + * @indio_dev: The IIO device associated with the sampling hardware. + * + * Basically power up device. + * Called with IIO device's lock held. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_preenable_buffer(struct iio_dev *indio_dev) +{ + int ret = zpa2326_resume(indio_dev); + + if (ret < 0) + return ret; + + /* Tell zpa2326_postenable_buffer() if we have just been powered on. */ + ((struct zpa2326_private *) + iio_priv(indio_dev))->waken = iio_priv(indio_dev); + + return 0; +} + +/** + * zpa2326_postenable_buffer() - Configure device for triggered sampling. + * @indio_dev: The IIO device associated with the sampling hardware. + * + * Basically setup one-shot mode if plugging external trigger. + * Otherwise, let internal trigger configure continuous sampling : + * see zpa2326_set_trigger_state(). + * + * If an error is returned, IIO layer will call our postdisable hook for us, + * i.e. no need to explicitly power device off here. + * Called with IIO device's lock held. + * + * Called with IIO device's lock held. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_postenable_buffer(struct iio_dev *indio_dev) +{ + const struct zpa2326_private *priv = iio_priv(indio_dev); + int err; + + if (!priv->waken) { + /* + * We were already power supplied. Just clear hardware FIFO to + * get rid of samples acquired during previous rounds (if any). + */ + err = zpa2326_clear_fifo(indio_dev, 0); + if (err) + goto err; + } + + if (!iio_trigger_using_own(indio_dev) && priv->waken) { + /* + * We are using an external trigger and we have just been + * powered up: reconfigure one-shot mode. + */ + err = zpa2326_config_oneshot(indio_dev, priv->irq); + if (err) + goto err; + } + + /* Plug our own trigger event handler. */ + err = iio_triggered_buffer_postenable(indio_dev); + if (err) + goto err; + + return 0; + +err: + zpa2326_err(indio_dev, "failed to enable buffering (%d)", err); + + return err; +} + +static int zpa2326_postdisable_buffer(struct iio_dev *indio_dev) +{ + zpa2326_suspend(indio_dev); + + return 0; +} + +static const struct iio_buffer_setup_ops zpa2326_buffer_setup_ops = { + .preenable = zpa2326_preenable_buffer, + .postenable = zpa2326_postenable_buffer, + .predisable = iio_triggered_buffer_predisable, + .postdisable = zpa2326_postdisable_buffer +}; + +/** + * zpa2326_set_trigger_state() - Start / stop continuous sampling. + * @trig: The trigger being attached to IIO device associated with the sampling + * hardware. + * @state: Tell whether to start (true) or stop (false) + * + * Basically enable / disable hardware continuous sampling mode. + * + * Called with IIO device's lock held at postenable() or predisable() time. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_set_trigger_state(struct iio_trigger *trig, bool state) +{ + const struct iio_dev *indio_dev = dev_get_drvdata( + trig->dev.parent); + const struct zpa2326_private *priv = iio_priv(indio_dev); + int err; + + if (!state) { + /* + * Switch trigger off : in case of failure, interrupt is left + * disabled in order to prevent handler from accessing released + * resources. + */ + unsigned int val; + + /* + * As device is working in continuous mode, handlers may be + * accessing resources we are currently freeing... + * Prevent this by disabling interrupt handlers and ensure + * the device will generate no more interrupts unless explicitly + * required to, i.e. by restoring back to default one shot mode. + */ + disable_irq(priv->irq); + + /* + * Disable continuous sampling mode to restore settings for + * one shot / direct sampling operations. + */ + err = regmap_write(priv->regmap, ZPA2326_CTRL_REG3_REG, + zpa2326_highest_frequency()->odr); + if (err) + return err; + + /* + * Now that device won't generate interrupts on its own, + * acknowledge any currently active interrupts (may happen on + * rare occasions while stopping continuous mode). + */ + err = regmap_read(priv->regmap, ZPA2326_INT_SOURCE_REG, &val); + if (err < 0) + return err; + + /* + * Re-enable interrupts only if we can guarantee the device will + * generate no more interrupts to prevent handlers from + * accessing released resources. + */ + enable_irq(priv->irq); + + zpa2326_dbg(indio_dev, "continuous mode stopped"); + } else { + /* + * Switch trigger on : start continuous sampling at required + * frequency. + */ + + if (priv->waken) { + /* Enable interrupt if getting out of reset. */ + err = regmap_write(priv->regmap, ZPA2326_CTRL_REG1_REG, + (u8) + ~ZPA2326_CTRL_REG1_MASK_DATA_READY); + if (err) + return err; + } + + /* Enable continuous sampling at specified frequency. */ + err = regmap_write(priv->regmap, ZPA2326_CTRL_REG3_REG, + ZPA2326_CTRL_REG3_ENABLE_MEAS | + priv->frequency->odr); + if (err) + return err; + + zpa2326_dbg(indio_dev, "continuous mode setup @%dHz", + priv->frequency->hz); + } + + return 0; +} + +static const struct iio_trigger_ops zpa2326_trigger_ops = { + .owner = THIS_MODULE, + .set_trigger_state = zpa2326_set_trigger_state, +}; + +/** + * zpa2326_init_trigger() - Create an interrupt driven / hardware trigger + * allowing to notify external devices a new sample is + * ready. + * @parent: Hardware sampling device @indio_dev is a child of. + * @indio_dev: The IIO device associated with the sampling hardware. + * @private: Internal private state related to @indio_dev. + * @irq: Optional interrupt line the hardware uses to notify new data + * samples are ready. Negative or zero values indicate no interrupts + * are available, meaning polling is required. + * + * Only relevant when DT declares a valid interrupt line. + * + * Return: Zero when successful, a negative error code otherwise. + */ +static int zpa2326_init_managed_trigger(struct device *parent, + struct iio_dev *indio_dev, + struct zpa2326_private *private, + int irq) +{ + struct iio_trigger *trigger; + int ret; + + if (irq <= 0) + return 0; + + trigger = devm_iio_trigger_alloc(parent, "%s-dev%d", + indio_dev->name, indio_dev->id); + if (!trigger) + return -ENOMEM; + + /* Basic setup. */ + trigger->dev.parent = parent; + trigger->ops = &zpa2326_trigger_ops; + + private->trigger = trigger; + + /* Register to triggers space. */ + ret = devm_iio_trigger_register(parent, trigger); + if (ret) + dev_err(parent, "failed to register hardware trigger (%d)", + ret); + + return ret; +} + +static int zpa2326_get_frequency(const struct iio_dev *indio_dev) +{ + return ((struct zpa2326_private *)iio_priv(indio_dev))->frequency->hz; +} + +static int zpa2326_set_frequency(struct iio_dev *indio_dev, int hz) +{ + struct zpa2326_private *priv = iio_priv(indio_dev); + int freq; + int err; + + /* Check if requested frequency is supported. */ + for (freq = 0; freq < ARRAY_SIZE(zpa2326_sampling_frequencies); freq++) + if (zpa2326_sampling_frequencies[freq].hz == hz) + break; + if (freq == ARRAY_SIZE(zpa2326_sampling_frequencies)) + return -EINVAL; + + /* Don't allow changing frequency if buffered sampling is ongoing. */ + err = iio_device_claim_direct_mode(indio_dev); + if (err) + return err; + + priv->frequency = &zpa2326_sampling_frequencies[freq]; + + iio_device_release_direct_mode(indio_dev); + + return 0; +} + +/* Expose supported hardware sampling frequencies (Hz) through sysfs. */ +static IIO_CONST_ATTR_SAMP_FREQ_AVAIL("1 5 11 23"); + +static struct attribute *zpa2326_attributes[] = { + &iio_const_attr_sampling_frequency_available.dev_attr.attr, + NULL +}; + +static const struct attribute_group zpa2326_attribute_group = { + .attrs = zpa2326_attributes, +}; + +static int zpa2326_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, + int *val2, + long mask) +{ + switch (mask) { + case IIO_CHAN_INFO_RAW: + return zpa2326_sample_oneshot(indio_dev, chan->type, val); + + case IIO_CHAN_INFO_SCALE: + switch (chan->type) { + case IIO_PRESSURE: + /* + * Pressure resolution is 1/64 Pascal. Scale to kPascal + * as required by IIO ABI. + */ + *val = 1; + *val2 = 64000; + return IIO_VAL_FRACTIONAL; + + case IIO_TEMP: + /* + * Temperature follows the equation: + * Temp[degC] = Tempcode * 0.00649 - 176.83 + * where: + * Tempcode is composed the raw sampled 16 bits. + * + * Hence, to produce a temperature in milli-degrees + * Celsius according to IIO ABI, we need to apply the + * following equation to raw samples: + * Temp[milli degC] = (Tempcode + Offset) * Scale + * where: + * Offset = -176.83 / 0.00649 + * Scale = 0.00649 * 1000 + */ + *val = 6; + *val2 = 490000; + return IIO_VAL_INT_PLUS_MICRO; + + default: + return -EINVAL; + } + + case IIO_CHAN_INFO_OFFSET: + switch (chan->type) { + case IIO_TEMP: + *val = -17683000; + *val2 = 649; + return IIO_VAL_FRACTIONAL; + + default: + return -EINVAL; + } + + case IIO_CHAN_INFO_SAMP_FREQ: + *val = zpa2326_get_frequency(indio_dev); + return IIO_VAL_INT; + + default: + return -EINVAL; + } +} + +static int zpa2326_write_raw(struct iio_dev *indio_dev, + const struct iio_chan_spec *chan, + int val, + int val2, + long mask) +{ + if ((mask != IIO_CHAN_INFO_SAMP_FREQ) || val2) + return -EINVAL; + + return zpa2326_set_frequency(indio_dev, val); +} + +static const struct iio_chan_spec zpa2326_channels[] = { + [0] = { + .type = IIO_PRESSURE, + .scan_index = 0, + .scan_type = { + .sign = 'u', + .realbits = 24, + .storagebits = 32, + .endianness = IIO_LE, + }, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | + BIT(IIO_CHAN_INFO_SCALE), + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), + }, + [1] = { + .type = IIO_TEMP, + .scan_index = 1, + .scan_type = { + .sign = 's', + .realbits = 16, + .storagebits = 16, + .endianness = IIO_LE, + }, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | + BIT(IIO_CHAN_INFO_SCALE) | + BIT(IIO_CHAN_INFO_OFFSET), + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), + }, + [2] = IIO_CHAN_SOFT_TIMESTAMP(2), +}; + +static const struct iio_info zpa2326_info = { + .driver_module = THIS_MODULE, + .attrs = &zpa2326_attribute_group, + .read_raw = zpa2326_read_raw, + .write_raw = zpa2326_write_raw, +}; + +static struct iio_dev *zpa2326_create_managed_iiodev(struct device *device, + const char *name, + struct regmap *regmap) +{ + struct iio_dev *indio_dev; + + /* Allocate space to hold IIO device internal state. */ + indio_dev = devm_iio_device_alloc(device, + sizeof(struct zpa2326_private)); + if (!indio_dev) + return NULL; + + /* Setup for userspace synchronous on demand sampling. */ + indio_dev->modes = INDIO_DIRECT_MODE; + indio_dev->dev.parent = device; + indio_dev->channels = zpa2326_channels; + indio_dev->num_channels = ARRAY_SIZE(zpa2326_channels); + indio_dev->name = name; + indio_dev->info = &zpa2326_info; + + return indio_dev; +} + +int zpa2326_probe(struct device *parent, + const char *name, + int irq, + unsigned int hwid, + struct regmap *regmap) +{ + struct iio_dev *indio_dev; + struct zpa2326_private *priv; + int err; + unsigned int id; + + indio_dev = zpa2326_create_managed_iiodev(parent, name, regmap); + if (!indio_dev) + return -ENOMEM; + + priv = iio_priv(indio_dev); + + priv->vref = devm_regulator_get(parent, "vref"); + if (IS_ERR(priv->vref)) + return PTR_ERR(priv->vref); + + priv->vdd = devm_regulator_get(parent, "vdd"); + if (IS_ERR(priv->vdd)) + return PTR_ERR(priv->vdd); + + /* Set default hardware sampling frequency to highest rate supported. */ + priv->frequency = zpa2326_highest_frequency(); + + /* + * Plug device's underlying bus abstraction : this MUST be set before + * registering interrupt handlers since an interrupt might happen if + * power up sequence is not properly applied. + */ + priv->regmap = regmap; + + err = devm_iio_triggered_buffer_setup(parent, indio_dev, NULL, + zpa2326_trigger_handler, + &zpa2326_buffer_setup_ops); + if (err) + return err; + + err = zpa2326_init_managed_trigger(parent, indio_dev, priv, irq); + if (err) + return err; + + err = zpa2326_init_managed_irq(parent, indio_dev, priv, irq); + if (err) + return err; + + /* Power up to check device ID and perform initial hardware setup. */ + err = zpa2326_power_on(indio_dev, priv); + if (err) + return err; + + /* Read id register to check we are talking to the right slave. */ + err = regmap_read(regmap, ZPA2326_DEVICE_ID_REG, &id); + if (err) + goto sleep; + + if (id != hwid) { + dev_err(parent, "found device with unexpected id %02x", id); + err = -ENODEV; + goto sleep; + } + + err = zpa2326_config_oneshot(indio_dev, irq); + if (err) + goto sleep; + + /* Setup done : go sleeping. Device will be awaken upon user request. */ + err = zpa2326_sleep(indio_dev); + if (err) + goto poweroff; + + dev_set_drvdata(parent, indio_dev); + + zpa2326_init_runtime(parent); + + err = iio_device_register(indio_dev); + if (err) { + zpa2326_fini_runtime(parent); + goto poweroff; + } + + return 0; + +sleep: + /* Put to sleep just in case power regulators are "dummy" ones. */ + zpa2326_sleep(indio_dev); +poweroff: + zpa2326_power_off(indio_dev, priv); + + return err; +} +EXPORT_SYMBOL_GPL(zpa2326_probe); + +void zpa2326_remove(const struct device *parent) +{ + struct iio_dev *indio_dev = dev_get_drvdata(parent); + + iio_device_unregister(indio_dev); + zpa2326_fini_runtime(indio_dev->dev.parent); + zpa2326_sleep(indio_dev); + zpa2326_power_off(indio_dev, iio_priv(indio_dev)); +} +EXPORT_SYMBOL_GPL(zpa2326_remove); + +MODULE_AUTHOR("Gregor Boirie "); +MODULE_DESCRIPTION("Core driver for Murata ZPA2326 pressure sensor"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/iio/pressure/zpa2326.h b/drivers/iio/pressure/zpa2326.h new file mode 100644 index 000000000000..05d3e1e3a449 --- /dev/null +++ b/drivers/iio/pressure/zpa2326.h @@ -0,0 +1,89 @@ +/* + * Murata ZPA2326 pressure and temperature sensor IIO driver + * + * Copyright (c) 2016 Parrot S.A. + * + * Author: Gregor Boirie + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + */ + +#ifndef _ZPA2326_H +#define _ZPA2326_H + +/* Register map. */ +#define ZPA2326_REF_P_XL_REG (0x8) +#define ZPA2326_REF_P_L_REG (0x9) +#define ZPA2326_REF_P_H_REG (0xa) +#define ZPA2326_DEVICE_ID_REG (0xf) +#define ZPA2326_DEVICE_ID (0xb9) +#define ZPA2326_RES_CONF_REG (0x10) +#define ZPA2326_CTRL_REG0_REG (0x20) +#define ZPA2326_CTRL_REG0_ONE_SHOT BIT(0) +#define ZPA2326_CTRL_REG0_ENABLE BIT(1) +#define ZPA2326_CTRL_REG1_REG (0x21) +#define ZPA2326_CTRL_REG1_MASK_DATA_READY BIT(2) +#define ZPA2326_CTRL_REG2_REG (0x22) +#define ZPA2326_CTRL_REG2_SWRESET BIT(2) +#define ZPA2326_CTRL_REG3_REG (0x23) +#define ZPA2326_CTRL_REG3_ODR_SHIFT (4) +#define ZPA2326_CTRL_REG3_ENABLE_MEAS BIT(7) +#define ZPA2326_INT_SOURCE_REG (0x24) +#define ZPA2326_INT_SOURCE_DATA_READY BIT(2) +#define ZPA2326_THS_P_LOW_REG (0x25) +#define ZPA2326_THS_P_HIGH_REG (0x26) +#define ZPA2326_STATUS_REG (0x27) +#define ZPA2326_STATUS_P_DA BIT(1) +#define ZPA2326_STATUS_FIFO_E BIT(2) +#define ZPA2326_STATUS_P_OR BIT(5) +#define ZPA2326_PRESS_OUT_XL_REG (0x28) +#define ZPA2326_PRESS_OUT_L_REG (0x29) +#define ZPA2326_PRESS_OUT_H_REG (0x2a) +#define ZPA2326_TEMP_OUT_L_REG (0x2b) +#define ZPA2326_TEMP_OUT_H_REG (0x2c) + +struct device; +struct regmap; + +bool zpa2326_isreg_writeable(struct device *dev, unsigned int reg); +bool zpa2326_isreg_readable(struct device *dev, unsigned int reg); +bool zpa2326_isreg_precious(struct device *dev, unsigned int reg); + +/** + * zpa2326_probe() - Instantiate and register core ZPA2326 IIO device + * @parent: Hardware sampling device the created IIO device will be a child of. + * @name: Arbitrary name to identify the device. + * @irq: Interrupt line, negative if none. + * @hwid: Expected device hardware id. + * @regmap: Registers map used to abstract underlying bus accesses. + * + * Return: Zero when successful, a negative error code otherwise. + */ +int zpa2326_probe(struct device *parent, + const char *name, + int irq, + unsigned int hwid, + struct regmap *regmap); + +/** + * zpa2326_remove() - Unregister and destroy core ZPA2326 IIO device. + * @parent: Hardware sampling device the IIO device to remove is a child of. + */ +void zpa2326_remove(const struct device *parent); + +#ifdef CONFIG_PM +#include +extern const struct dev_pm_ops zpa2326_pm_ops; +#define ZPA2326_PM_OPS (&zpa2326_pm_ops) +#else +#define ZPA2326_PM_OPS (NULL) +#endif + +#endif diff --git a/drivers/iio/pressure/zpa2326_i2c.c b/drivers/iio/pressure/zpa2326_i2c.c new file mode 100644 index 000000000000..e4d27dd4493a --- /dev/null +++ b/drivers/iio/pressure/zpa2326_i2c.c @@ -0,0 +1,99 @@ +/* + * Murata ZPA2326 I2C pressure and temperature sensor driver + * + * Copyright (c) 2016 Parrot S.A. + * + * Author: Gregor Boirie + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + */ + +#include +#include +#include +#include +#include "zpa2326.h" + +/* + * read_flag_mask: + * - address bit 7 must be set to request a register read operation + */ +static const struct regmap_config zpa2326_regmap_i2c_config = { + .reg_bits = 8, + .val_bits = 8, + .writeable_reg = zpa2326_isreg_writeable, + .readable_reg = zpa2326_isreg_readable, + .precious_reg = zpa2326_isreg_precious, + .max_register = ZPA2326_TEMP_OUT_H_REG, + .read_flag_mask = BIT(7), + .cache_type = REGCACHE_NONE, +}; + +static unsigned int zpa2326_i2c_hwid(const struct i2c_client *client) +{ +#define ZPA2326_SA0(_addr) (_addr & BIT(0)) +#define ZPA2326_DEVICE_ID_SA0_SHIFT (1) + + /* Identification register bit 1 mirrors device address bit 0. */ + return (ZPA2326_DEVICE_ID | + (ZPA2326_SA0(client->addr) << ZPA2326_DEVICE_ID_SA0_SHIFT)); +} + +static int zpa2326_probe_i2c(struct i2c_client *client, + const struct i2c_device_id *i2c_id) +{ + struct regmap *regmap; + + regmap = devm_regmap_init_i2c(client, &zpa2326_regmap_i2c_config); + if (IS_ERR(regmap)) { + dev_err(&client->dev, "failed to init registers map"); + return PTR_ERR(regmap); + } + + return zpa2326_probe(&client->dev, i2c_id->name, client->irq, + zpa2326_i2c_hwid(client), regmap); +} + +static int zpa2326_remove_i2c(struct i2c_client *client) +{ + zpa2326_remove(&client->dev); + + return 0; +} + +static const struct i2c_device_id zpa2326_i2c_ids[] = { + { "zpa2326", 0 }, + { }, +}; +MODULE_DEVICE_TABLE(i2c, zpa2326_i2c_ids); + +#if defined(CONFIG_OF) +static const struct of_device_id zpa2326_i2c_matches[] = { + { .compatible = "murata,zpa2326" }, + { } +}; +MODULE_DEVICE_TABLE(of, zpa2326_i2c_matches); +#endif + +static struct i2c_driver zpa2326_i2c_driver = { + .driver = { + .name = "zpa2326-i2c", + .of_match_table = of_match_ptr(zpa2326_i2c_matches), + .pm = ZPA2326_PM_OPS, + }, + .probe = zpa2326_probe_i2c, + .remove = zpa2326_remove_i2c, + .id_table = zpa2326_i2c_ids, +}; +module_i2c_driver(zpa2326_i2c_driver); + +MODULE_AUTHOR("Gregor Boirie "); +MODULE_DESCRIPTION("I2C driver for Murata ZPA2326 pressure sensor"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/iio/pressure/zpa2326_spi.c b/drivers/iio/pressure/zpa2326_spi.c new file mode 100644 index 000000000000..bd2c1c319fca --- /dev/null +++ b/drivers/iio/pressure/zpa2326_spi.c @@ -0,0 +1,103 @@ +/* + * Murata ZPA2326 SPI pressure and temperature sensor driver + * + * Copyright (c) 2016 Parrot S.A. + * + * Author: Gregor Boirie + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + */ + +#include +#include +#include +#include +#include "zpa2326.h" + +/* + * read_flag_mask: + * - address bit 7 must be set to request a register read operation + * - address bit 6 must be set to request register address auto increment + */ +static const struct regmap_config zpa2326_regmap_spi_config = { + .reg_bits = 8, + .val_bits = 8, + .writeable_reg = zpa2326_isreg_writeable, + .readable_reg = zpa2326_isreg_readable, + .precious_reg = zpa2326_isreg_precious, + .max_register = ZPA2326_TEMP_OUT_H_REG, + .read_flag_mask = BIT(7) | BIT(6), + .cache_type = REGCACHE_NONE, +}; + +static int zpa2326_probe_spi(struct spi_device *spi) +{ + struct regmap *regmap; + int err; + + regmap = devm_regmap_init_spi(spi, &zpa2326_regmap_spi_config); + if (IS_ERR(regmap)) { + dev_err(&spi->dev, "failed to init registers map"); + return PTR_ERR(regmap); + } + + /* + * Enforce SPI slave settings to prevent from DT misconfiguration. + * + * Clock is idle high. Sampling happens on trailing edge, i.e., rising + * edge. Maximum bus frequency is 1 MHz. Registers are 8 bits wide. + */ + spi->mode = SPI_MODE_3; + spi->max_speed_hz = min(spi->max_speed_hz, 1000000U); + spi->bits_per_word = 8; + err = spi_setup(spi); + if (err < 0) + return err; + + return zpa2326_probe(&spi->dev, spi_get_device_id(spi)->name, + spi->irq, ZPA2326_DEVICE_ID, regmap); +} + +static int zpa2326_remove_spi(struct spi_device *spi) +{ + zpa2326_remove(&spi->dev); + + return 0; +} + +static const struct spi_device_id zpa2326_spi_ids[] = { + { "zpa2326", 0 }, + { }, +}; +MODULE_DEVICE_TABLE(spi, zpa2326_spi_ids); + +#if defined(CONFIG_OF) +static const struct of_device_id zpa2326_spi_matches[] = { + { .compatible = "murata,zpa2326" }, + { } +}; +MODULE_DEVICE_TABLE(of, zpa2326_spi_matches); +#endif + +static struct spi_driver zpa2326_spi_driver = { + .driver = { + .name = "zpa2326-spi", + .of_match_table = of_match_ptr(zpa2326_spi_matches), + .pm = ZPA2326_PM_OPS, + }, + .probe = zpa2326_probe_spi, + .remove = zpa2326_remove_spi, + .id_table = zpa2326_spi_ids, +}; +module_spi_driver(zpa2326_spi_driver); + +MODULE_AUTHOR("Gregor Boirie "); +MODULE_DESCRIPTION("SPI driver for Murata ZPA2326 pressure sensor"); +MODULE_LICENSE("GPL v2"); -- cgit v1.2.3