| Age | Commit message (Collapse) | Author |
|---|
|
The CPU ticks at a rate in the "bus clock" domain.
eg. 100 MHz * bus_ratio.
On newer processors, the TSC has been moved out of this BCLK
domain and into a separate crystal-clock domain.
While the TSC ticks "close to" the base frequency, those that look
closely at the numbers will notice small errors in calculations that
mix units of TSC clocks and bus clocks.
"tsc_tweak" was introduced to address the most visible
mixing -- the %Busy and the the Busy_MHz calculations.
(A simplification as since removed TSC from the BusyMHz calculation)
Here we apply the tsc_tweak to everyplace where BCLK
and TSC units are mixed. The results is that
on a system which is 100% idle, the sum of the C-states
are now much more likely to be closer to 100%.
Reported-by: Travis Downs <travis.downs@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Some users want turbostat to tell them everything, by default.
Some users want turbostat to be quiet, by default.
I find that I'm in the 1st camp, and so I've never liked
needing to type the --debug parameter to decode the system
configuration.
So here we change the default and print the system configuration,
by default. (The --debug option is now un-documented, though
it does still exist for debugging turbostat internals)
When you do not want to see the system configuration
header, use the new "--quiet" option.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Some time ago, turbostat overflowed 80 columns.
So on the assumption that a "casual" user would always
want topology and frequency columns, we hid the rest
of the columns and the system configuration decoding
behind the --debug option.
Not everybody liked that change -- including me.
I use --debug 99% of the time...
Well, now we have "-o file" to put turbostat output into a file,
so unless you are watching real-time in a small window,
column count is less frequently a factor.
And more recently, we got the "--hide columnA,columnB" option
to specify columns to skip.
So now we "un-hide" the rest of the columns from behind --debug,
and show them all, by default.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
useful for observing if the BIOS disabled prefetch
Not architectural, but docuemented as present on NHM, SNB
and is present on others.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
show the CPUID feature for turbo to clarify the case
when it may not be shown in MISC_ENABLE
CPUID(6): APERF, TURBO, DTS, PTM, No-HWP, No-HWPnotify, No-HWPwindow, No-HWPepp, No-HWPpkg, EPB
cpu4: MSR_IA32_MISC_ENABLE: 0x00850089 (TCC EIST MWAIT TURBO)
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Turbostat dumps MSR_TURBO_RATIO_LIMIT on Core Architecture.
But Atom Architecture uses MSR_ATOM_CORE_RATIOS and
MSR_ATOM_CORE_TURBO_RATIOS.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Decode MISC_ENABLE.NO_TURBO,
also use the #defines in msr-index.h for decoding this register
cpu0: MSR_IA32_MISC_ENABLE: 0x00850089 (TCC EIST MWAIT TURBO)
Although it is not architectural, decode also
MSR_IA32_MISC_ENABLE.prefetch-disable (bit-9).
documented to be present on: Core, P4, Intel-Xeon
reserved on: Atom, Silvermont, Nehalem, SNB, PHI ec.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add a digit of precision to the --debug output for frequency range.
This is useful when BCLK is not an integer.
old:
6 * 83 = 500 MHz max efficiency frequency
26 * 83 = 2166 MHz base frequency
new:
6 * 83.3 = 499.8 MHz max efficiency frequency
26 * 83.3 = 2165.8 MHz base frequency
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The Baytrail SOC, with its Silvermont core, has some unique properties:
1. a hardware CC1 residency counter
2. a module-c6 residency counter
3. a package-c6 counter at traditional package-c7 counter address.
The SOC does not support c3, pc3, c7 or pc7 counters.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Previously called MSR_NHM_SNB_PKG_CST_CFG_CTL
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest update from Shuah Khan:
"This update consists of:
- fixes to several existing tests from Stafford Horne
- cpufreq tests from Viresh Kumar
- Selftest build and install fixes from Bamvor Jian Zhang and Michael
Ellerman
- Fixes to protection-keys tests from Dave Hansen
- Warning fixes from Shuah Khan"
* tag 'linux-kselftest-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (28 commits)
selftests/powerpc: Fix remaining fallout from recent changes
selftests/powerpc: Fix the clean rule since recent changes
selftests: Fix the .S and .S -> .o rules
selftests: Fix the .c linking rule
selftests: Fix selftests build to just build, not run tests
selftests, x86, protection_keys: fix wrong offset in siginfo
selftests, x86, protection_keys: fix uninitialized variable warning
selftest: cpufreq: Update MAINTAINERS file
selftest: cpufreq: Add special tests
selftest: cpufreq: Add support to test cpufreq modules
selftest: cpufreq: Add suspend/resume/hibernate support
selftest: cpufreq: Add support for cpufreq tests
selftests: Add intel_pstate to TARGETS
selftests/intel_pstate: Update makefile to match new style
selftests/intel_pstate: Fix warning on loop index overflow
cpupower: Restore format of frequency-info limit
selftests/futex: Add headers to makefile dependencies
selftests/futex: Add stdio used for logging
selftests: x86 protection_keys remove dead code
selftests: x86 protection_keys fix unused variable compile warnings
...
|
|
AMT value 0 is unlimited, not PC0
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Without --debug, a debug line was printed on Baytrail:
SLM BCLK: 83.3 Mhz
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
with --debug, see:
cpu0: MSR_CC6_DEMOTION_POLICY_CONFIG: 0x00000000 (DISable-CC6-Demotion)
cpu0: MSR_MC6_DEMOTION_POLICY_CONFIG: 0x00000000 (DISable-MC6-Demotion)
Note that the hardware default is to enable demotion,
and Linux started clearing these registers in 3.17.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
and so --debug fails with:
turbostat: msr 1 offset 0x1aa read failed: Input/output error
It seems that baytrail, and airmont do not have this MSR.
It is included in subsequent Goldmont Atom.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add the "--show" and "--hide" cmdline parameters.
By default, turbostat shows all columns.
turbostat --hide counter_list
will continue showing all columns, except for those listed.
turbostat --show counter_list
will show _only_ the listed columns
These features work for built-in counters, and have no effect
on columns added with the --add parameter.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
When --add was used more than once, overflowed buffers
caused some counters to be stored on top of others,
corrupting the results. Simplify the code by simply
reserving space for up to 16 added counters per each
cpu, core, package.
Per-cpu added counters were being printed only per-core.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20170119, which among other things updates copyright notices in all of
the ACPICA files, fix a couple of issues in the ACPI EC and button
drivers, fix modalias handling for non-discoverable devices with
DT-compatible identification strings, add a suspend quirk for one
platform and fix a message in the APEI code.
Specifics:
- Update of the ACPICA code in the kernel to upstream revision
20170119 including:
+ Fixes related to the handling of the bit width and bit offset
fields in Generic Address Structure (Lv Zheng)
+ ACPI resources handling fix related to invalid resource
descriptors (Bob Moore)
+ Fix to enable implicit result conversion for several ASL library
functions (Bob Moore)
+ Support for method invocations as target operands in AML (Bob
Moore)
+ Fix to use a correct operand type for DeRefOf() in some
situations (Bob Moore)
+ Utilities updates (Bob Moore, Lv Zheng)
+ Disassembler/debugger updates (David Box, Lv Zheng)
+ Build fixes (Colin Ian King, Lv Zheng)
+ Update of copyright notices in all files (Bob Moore)
- Fix for modalias handling for SPI and I2C devices with
DT-compatible identification strings (Dan O'Donovan)
- Fixes for the ACPI EC and button drivers (Lv Zheng)
- ACPI processor handling fix related to CPU hotplug (online/offline)
on x86 (Vitaly Kuznetsov)
- Suspend quirk to save/restore NVS memory over S3 transitions for
Lenovo G50-45 (Zhang Rui)
- Message formatting fix for the ACPI APEI code (Colin Ian King)"
* tag 'acpi-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
ACPICA: Update version to 20170119
ACPICA: Tools: Update common signon, remove compilation bit width
ACPICA: Source tree: Update copyright notices to 2017
ACPICA: Linuxize: Restore and fix Intel compiler build
x86/ACPI: keep x86_cpu_to_acpiid mapping valid on CPU hotplug
spi: acpi: Initialize modalias from of_compatible
i2c: acpi: Initialize info.type from of_compatible
ACPI / bus: Introduce acpi_of_modalias() equiv of of_modalias_node()
ACPI: save NVS memory for Lenovo G50-45
ACPI, APEI, EINJ: fix malformed newline escape
ACPI / button: Remove lid_init_state=method mode
ACPI / button: Change default behavior to lid_init_state=open
ACPI / EC: Use busy polling mode when GPE is not enabled
ACPI / EC: Remove old CLEAR_ON_RESUME quirk
ACPICA: Update version to 20161222
ACPICA: Parser: Update parse info table for some operators
ACPICA: Fix a problem with recent extra support for control method invocations
ACPICA: Parser: Allow method invocations as target operands
ACPICA: Fix for implicit result conversion for the ToXXX functions
ACPICA: Resources: Not a valid resource if buffer length too long
..
|
|
This utility can be used to debug and tune the performance of the
intel_pstate driver.
This utility can be used in two ways:
- If there is Linux trace file with pstate_sample events enabled, then
this utility can parse the trace file and generate performance plots.
- If user has not specified a trace file as input via command line
parameters, then this utility enables and collects trace data for a
user-specified interval and generates performance plots.
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit 16577e5265923f4999b4d2c0addb2343b18135e1
Affects all files.
Link: https://github.com/acpica/acpica/commit/16577e52
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The intel_pstate kselftest expects that the output of
`cpupower frequency-info -l | tail -1 | awk ' { print $1 } '`
to get frequency limits. This does not work after the following two
changes.
- 562e5f1a3: rework the "cpupower frequency-info" command
(Jacob Tanenbaum) removed parsable limit output
- ce512b840: Do not analyse offlined cpus
(Thomas Renninger) added newline to break limit parsing more
This change preserves human readable output if wanted as well as
parsable output for scripts/tests.
Cc: Thomas Renninger <trenn@suse.com>
Cc: "Shreyas B. Prabhu" <shreyas@linux.vnet.ibm.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
ACPICA commit ba665dc8e20d9f7730466a659564dd6c557a6cbc
In Linux, para-virtualization implmentation hooks critical register
writes to prevent real hardware operations. This increases divergences
when the sleep registers are cracked in Linux resident ACPICA.
This patch tries to introduce a single OSL to reduce the divergences.
Link: https://github.com/acpica/acpica/commit/ba665dc8
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown.
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: remove obsolete -M, -m, -C, -c options
tools/power turbostat: Make extensible via the --add parameter
tools/power turbostat: Denverton uses a 25 MHz crystal, not 19.2 MHz
tools/power turbostat: line up headers when -M is used
tools/power turbostat: fix SKX PKG_CSTATE_LIMIT decoding
tools/power turbostat: Support Knights Mill (KNM)
tools/power turbostat: Display HWP OOB status
tools/power turbostat: fix Denverton BCLK
tools/power turbostat: use intel-family.h model strings
tools/power/turbostat: Add Denverton RAPL support
tools/power/turbostat: Add Denverton support
tools/power/turbostat: split core MSR support into status + limit
tools/power turbostat: fix error case overflow read of slm_freq_table[]
tools/power turbostat: Allocate correct amount of fd and irq entries
tools/power turbostat: switch to tab delimited output
tools/power turbostat: Gracefully handle ACPI S3
tools/power turbostat: tidy up output on Joule counter overflow
|
|
The new --add option has replaced the -M, -m, -C, -c options
Eg.
-M 0x10 is now --add msr0x10,raw
-m 0x10 is now --add msr0x10,raw,u32
-C 0x10 is now --add msr0x10,delta
-c 0x10 is now --add msr0x10,delta,u32
The --add option can be repeated to add any number of counters,
while the previous options were limited to adding one of each type.
In addition, the --add option can accept a column label,
and can also display a counter as a percentage of elapsed cycles.
Eg. --add msr0x3fe,core,percent,MY_CC3
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Create the "--add" parameter. This can be used to teach an existing
turbostat binary about any number of any type of counter.
turbostat(8) details the syntax for --add.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
- prototypes for x86 asm-exported symbols (Adam Borowski) and a warning
about missing CRCs (Nick Piggin)
- asm-exports fix for LTO (Nicolas Pitre)
- thin archives improvements (Nick Piggin)
- linker script fix for CONFIG_LD_DEAD_CODE_DATA_ELIMINATION (Nick
Piggin)
- genksyms support for __builtin_va_list keyword
- misc minor fixes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
x86/kbuild: enable modversions for symbols exported from asm
kbuild: fix scripts/adjust_autoksyms.sh* for the no modules case
scripts/kallsyms: remove last remnants of --page-offset option
make use of make variable CURDIR instead of calling pwd
kbuild: cmd_export_list: tighten the sed script
kbuild: minor improvement for thin archives build
kbuild: modpost warn if export version crc is missing
kbuild: keep data tables through dead code elimination
kbuild: improve linker compatibility with lib-ksyms.o build
genksyms: Regenerate parser
kbuild/genksyms: handle va_list type
kbuild: thin archives for multi-y targets
kbuild: kallsyms allow 3-pass generation if symbols size has changed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
NTB: correct ntb_spad_count comment typo
misc: ibmasm: fix typo in error message
Remove references to dead make variable LINUX_INCLUDE
Remove last traces of ikconfig.h
treewide: Fix printk() message errors
Documentation/device-mapper: s/getsize/getsz/
|
|
This patch fix spelling typos in printk and kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
* acpica:
ACPICA: Utilities: Add new decode function for parser values
ACPICA: Tables: Add an error message complaining driver bugs
ACPICA: Tables: Add acpi_tb_unload_table()
ACPICA: Tables: Cleanup acpi_tb_install_and_load_table()
ACPICA: Events: Fix acpi_ev_initialize_region() return value
ACPICA: Back port of "ACPICA: Dispatcher: Tune interpreter lock around AcpiEvInitializeRegion()"
ACPICA: Namespace: Add acpi_ns_handle_to_name()
ACPICA: Update version to 20160930
ACPICA: Move acpi_gbl_max_loop_iterations to the public globals file
ACPICA: Disassembler: Fix for Divide() support, new support for test suite
ACPICA: Increase loop limit for AE_AML_INFINITE_LOOP exception
ACPICA: MacOSX: Fix wrong sem_destroy definition
ACPICA: MacOSX: Fix anonymous semaphore implementation
ACPICA: Update an info message during table load phase
|
|
make already provides the current working directory in a variable, so make
use of it instead of forking a shell. Also replace usage of PWD by
CURDIR. PWD is provided by most shells, but not all, so this makes the
build system more robust.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Michal Marek <mmarek@suse.com>
|
|
This changes only the TSC frequency decoding line seen with --debug
old: TSC: 1382 MHz (19200000 Hz * 216 / 3 / 1000000)
new: TSC: 1800 MHz (25000000 Hz * 216 / 3 / 1000000)
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The -M option adds an 18-column item, and the header
needs to be wide enough to keep the header aligned
with the columns.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
SKX has fewer package C-states than previous generations,
and so the decoding of PKG_CSTATE_LIMIT has changed.
This changes the line ending with pkg-cstate-limit=XXX: pcYYY
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
|
|
Original-author: Piotr Luc <piotr.luc@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Display if the HWP is enabled in OOB (Out of band) mode.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add Denverton to the group of SandyBridge and later processors,
to let the bclk be recognized as 100MHz rather than 133MHz,
then avoid the wrong value of the frequencies based on it,
including Bzy_MHz, max efficiency freuency, base frequency,
and turbo mode frequencies.
Signed-off-by: Xiaolong Wang <xiaolong.wang@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
All except for model 1F, a Nehalem, which is currently incorrectly
indentified as a Westmere in that new header.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The Denverton CPU RAPL supports package, core, and DRAM domains.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Denverton is an Atom based micro server which shares the same
Goldmont architecture as Broxton. The available C-states on
Denverton is a subset of Broxton with only C1, C1e, and C6.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Some CPUs may not have PP0/Core domain power limit MSRs. We
should still allow its domain energy status to be used. This
patch splits PP0/Core RAPL into two separate flags for power
limit and energy status such that energy status can continue
to be reported without power limit.
Without this patch, turbostat will not be able to use the
remaining RAPL features if some PL MSRs are not present.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
When i >= SLM_BCLK_FREQS, the frequency read from the slm_freq_table
is off the end of the array because msr is set to 3 rather than the
actual array index i. Set i to 3 rather than msr to fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The tool uses topo.max_cpu_num to determine number of entries needed for
fd_percpu[] and irqs_per_cpu[]. For example on a system with 4 CPUs
topo.max_cpu_num is 3 so we get too small array for holding per-CPU items.
Fix this to use right number of entries, which is topo.max_cpu_num + 1.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Switch to tab-delimited output from fixed-width columns
to make it simpler to import into spreadsheets.
As the fixed width columnns were 8-spaces wide,
the output on the screen should not change.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
turbostat gives valid results across suspend to idle, aka freeze,
whether invoked in interval mode, or in command mode.
Indeed, this can be used to measure suspend to idle:
turbostat echo freeze > /sys/power/state
But this does not work across suspend to ACPI S3, because the
processor counters, including the TSC, are reset on resume.
Further, when turbostat detects a problem, it does't forgive
the hardware, and interval mode will print *'s from there on out.
Instead, upon detecting counters going backwards, simply
reset and start over.
Interval mode across ACPI S3: (observe TSC going backwards)
root@sharkbay:/home/lenb/turbostat-src# ./turbostat -M 0x10
CPU Avg_MHz Busy% Bzy_MHz TSC_MHz MSR 0x010
- 1 0.06 858 2294 0x0000000000000000
0 0 0.06 847 2294 0x0000002a254b98ac
1 1 0.06 878 2294 0x0000002a254efa3a
2 1 0.07 843 2294 0x0000002a2551df65
3 0 0.05 863 2294 0x0000002a2553fea2
turbostat: re-initialized with num_cpus 4
CPU Avg_MHz Busy% Bzy_MHz TSC_MHz MSR 0x010
- 2 0.20 849 2294 0x0000000000000000
0 2 0.26 856 2294 0x0000000449abb60d
1 2 0.20 844 2294 0x0000000449b087ec
2 2 0.21 850 2294 0x0000000449b35d5d
3 1 0.12 839 2294 0x0000000449b5fd5a
^C
Command mode across ACPI S3:
root@sharkbay:/home/lenb/turbostat-src# ./turbostat -M 0x10 sleep 10
./turbostat: Counter reset detected
14.196299 sec
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The RAPL Joules counter is limited in capacity.
Turbostat estimates how soon it can roll-over
based on the max TDP of the processor --
which tells us the maximum increment rate.
eg.
RAPL: 2759 sec. Joule Counter Range, at 95 Watts
So if a sample duration is longer than 2759 seconds on this system,
'**' replace the decimal place in the display to indicate
that the results may be suspect.
But the display had an extra ' ' in this case, throwing off the columns.
Also, the -J "Joules" option appended an extra "time" column
to the display. While this may be useful, it printed the interval time,
which may not be the accurate time per processor. Remove this column,
which appeared only when using '-J',
as we plan to add accurate per-cpu interval times in a future commit.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Avoid breaking cross-compiled ACPI tools builds by rearranging the
handling of kernel header files.
This patch also contains OUTPUT/srctree cleanups in order to make above fix
working for various build environments.
Fixes: e323c02dee59 (ACPICA: MSVC9: Fix <sys/stat.h> inclusion order issue)
Reported-and-tested-by: Yisheng Xie <xieyisheng1@huawei.com>
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When converting to a shared library in ac5a181d065d ("cpupower: Add
cpuidle parts into library"), cpu_freq_cpu_exists() was converted to
cpupower_is_cpu_online(). cpu_req_cpu_exists() returned 0 on success and
-ENOSYS on failure whereas cpupower_is_cpu_online returns 1 on success.
Check for the correct return value in cpufreq-set.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1374212
Fixes: ac5a181d065d (cpupower: Add cpuidle parts into library)
Reported-by: Julian Seward <jseward@acm.org>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Thomas Renninger <trenn@suse.com>
Cc: 4.7+ <stable@vger.kernel.org> # 4.7+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit bbcb58f7875381d5c7f3d614bad3bc628a3f5cc6
The following build errors can be seen for MacOSX builds:
.../osunixxf.c:882:9: error: 'sem_close' is deprecated [-Werror,-Wdeprecated-declarations]
.../acmacosx.h:122:29: note: expanded from macro 'sem_destroy'
#define sem_destroy sem_close
sem_destroy() issue is caused by the wrong order of the following lines:
#define #sem_destroy sem_close
#include <semaphore.h>
This patch fixes it by removing the buggy re-definitiion. Lv Zheng.
Linux is not affected by this change.
Link: https://github.com/acpica/acpica/commit/bbcb58f7
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit 01eb9a58f4cf6300a0feb838a02bc4b1895c76e8
ACPICA commit de5b9c0ef1ccb264cbe57c88f6dd3fbf8229f907
The following build errors can be seen for MacOSX builds:
.../osunixxf.c:829:42: error: 'tmpnam' is deprecated: This function is provided for compatibility reasons only. Due to security concerns inherent in the design of tmpnam(3), it is highly recommended that you use mkstemp(3) instead. [-Werror,-Wdeprecated-declarations]
Using of temporal file name functions can easily result in bus errors on
MacOSX. This patch implements anonymous semaphore using an automatic
increasing number. Lv Zheng.
Linux is not affected by this change.
Link: https://github.com/acpica/acpica/commit/01eb9a58
Link: https://github.com/acpica/acpica/commit/de5b9c0e
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
