| Age | Commit message (Collapse) | Author |
|---|
|
Pull MTD updates from Brian Norris:
"General updates:
- Cleanups and additional flash support for "dataflash" driver
- new driver for mchp23k256 SPI SRAM device
- improve handling of MTDs without eraseblocks (i.e., MTD_NO_ERASE)
- refactor and improve "sub-partition" handling with TRX partition
parser; partitions can now be created as sub-partitions of another
partition
SPINOR updates, from Cyrille Pitchen and Marek Vasut:
- introduce support to the SPI 1-2-2 and 1-4-4 protocols.
- introduce support to the Double Data Rate (DDR) mode.
- introduce support to the Octo SPI protocols.
- add support to new memory parts for Spansion, Macronix and Winbond.
- add fixes for the Aspeed, STM32 and Cadence QSPI controler drivers.
- clean up the st_spi_fsm driver.
NAND updates, from Boris Brezillon:
- addition of on-die ECC support to Micron driver
- addition of helpers to help drivers choose most appropriate ECC
settings
- deletion of dead-code (cached programming and ->errstat() hook)
- make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
- change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
- support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
- change the prototype of ->setup_data_interface()
A bunch of driver related changes:
- various cleanup, fixes and improvements of the MTK driver
- OMAP DT bindings fixes
- support for ->setup_data_interface() in the fsmc driver
- support for imx7 in the gpmi driver
- finalization of the denali driver rework (thanks to Masahiro for
the work he's done on this driver)
- fix "bitflips in erased pages" handling in the ifc driver
- addition of PM ops and dynamic timing configuration to the atmel
driver"
* tag 'for-linus-20170713' of git://git.infradead.org/linux-mtd: (118 commits)
Documentation: ABI: mtd: describe "offset" more precisely
mtd: Fix check in mtd_unpoint()
mtd: nand: mtk: release lock on error path
mtd: st_spi_fsm: remove SPINOR_OP_RDSR2 and use SPINOR_OP_RDCR instead
mtd: spi-nor: cqspi: remove duplicate const
mtd: spi-nor: Add support for Spansion S25FL064L
mtd: spi-nor: Add support for mx66u51235f
mtd: nand: mtk: add ->setup_data_interface() hook
mtd: nand: mtk: remove unneeded mtk_ecc_hw_init from mtk_ecc_resume
mtd: nand: mtk: remove unneeded mtk_nfc_hw_init from mtk_nfc_resume
mtd: nand: mtk: disable ecc irq when writing page with hwecc
mtd: nand: mtk: fix incorrect register setting order about ecc irq
mtd: partitions: fixup some allocate_partition() whitespace
mtd: parsers: trx: fix pr_err format for printing offset
MAINTAINERS: Update SPI NOR subsystem git repositories
mtd: extract TRX parser out of bcm47xxpart into a separated module
mtd: partitions: add support for partition parsers
mtd: partitions: add support for subpartitions
mtd: partitions: rename "master" to the "parent" where appropriate
mtd: partitions: remove sysfs files when deleting all master's partitions
...
|
|
From Boris:
"""
This pull request contains the following core changes:
* addition of on-ecc support to Micron driver
* addition of helpers to help drivers choose most appropriate ECC
settings
* deletion of dead-code (cached programming and ->errstat() hook)
* make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
* change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
* support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
* change the prototype of ->setup_data_interface()
A bunch of driver related changes:
* various cleanup, fixes and improvements of the MTK driver
* OMAP DT bindings fixes
* support for ->setup_data_interface() in the fsmc driver
* support for imx7 in the gpmi driver
* finalization of the denali driver rework (thanks to Masahiro for the
work he's done on this driver)
* fix "bitflips in erased pages" handling in the ifc driver
* addition of PM ops and dynamic timing configuration to the atmel
driver
And as usual we also have a few minor cleanup/fixes/improvements
patches across the subsystem.
"""
|
|
From Cyrille:
"""
This pull request contains the following notable changes:
- introduce support to the SPI 1-2-2 and 1-4-4 protocols.
- introduce support to the Double Data Rate (DDR) mode.
- introduce support to the Octo SPI protocols.
- add support to new memory parts for Spansion, Macronix and Winbond.
- add fixes for the Aspeed, STM32 and Cadence QSPI controler drivers.
- clean up the st_spi_fsm driver.
"""
|
|
Some devices have partitions that are kind of containers with extra
subpartitions / volumes instead of e.g. a simple filesystem data. To
support such cases we need to first create normal flash device
partitions and then take care of these special ones.
It's very common case for home routers. Depending on the vendor there
are formats like TRX, Seama, TP-Link, WRGG & more. All of them are used
to embed few partitions into a single one / single firmware file.
Ideally all vendors would use some well documented / standardized format
like UBI (and some probably start doing so), but there are still
countless devices on the market using these poor vendor specific
formats.
This patch extends MTD subsystem by allowing to specify list of parsers
that should be tried for a given partition. Supporting such poor formats
is highly unlikely to be the top priority so these changes try to
minimize maintenance cost to the minimum. It reuses existing code for
these new parsers and just adds a one property and one new function.
This implementation requires setting partition parsers in a flash
parser. A proper change of bcm47xxpart will follow and in the future we
will hopefully also find a solution for doing it with ofpart
("fixed-partitions").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
struct nand_ecc_caps was designed as flexible as possible to support
multiple stepsizes (like sunxi_nand.c).
So, we need to write multiple arrays even for the simplest case.
I guess many controllers support a single stepsize, so here is a
shorthand macro for the case.
It allows to describe like ...
NAND_ECC_CAPS_SINGLE(denali_pci_ecc_caps, denali_calc_ecc_bytes, 512, 8, 15);
... instead of
static const int denali_pci_ecc_strengths[] = {8, 15};
static const struct nand_ecc_step_info denali_pci_ecc_stepinfo = {
.stepsize = 512,
.strengths = denali_pci_ecc_strengths,
.nstrengths = ARRAY_SIZE(denali_pci_ecc_strengths),
};
static const struct nand_ecc_caps denali_pci_ecc_caps = {
.stepinfos = &denali_pci_ecc_stepinfo,
.nstepinfos = 1,
.calc_ecc_bytes = denali_calc_ecc_bytes,
};
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Driver are responsible for setting up ECC parameters correctly.
Those include:
- Check if ECC parameters specified (usually by DT) are valid
- Meet the chip's ECC requirement
- Maximize ECC strength if NAND_ECC_MAXIMIZE flag is set
The logic can be generalized by factoring out common code.
This commit adds 3 helpers to the NAND framework:
nand_check_ecc_caps - Check if preset step_size and strength are valid
nand_match_ecc_req - Match the chip's requirement
nand_maximize_ecc - Maximize the ECC strength
To use the helpers above, a driver needs to provide:
- Data array of supported ECC step size and strength
- A hook that calculates ECC bytes from the combination of
step_size and strength.
By using those helpers, code duplication among drivers will be
reduced.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The ->errstat() hook is no longer implemented NAND controller drivers.
Get rid of it before someone starts abusing it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Some NAND controllers can assign different NAND timings to different
CS lines. Pass the CS line information to ->setup_data_interface() so
that the NAND controller driver knows which CS line is concerned by
the setup_data_interface() request.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Now that the core NAND subsystem has support for on-die ECC, this commit
brings the necessary code to support on-die ECC on Micron NANDs.
In micron_nand_init(), we detect if the Micron NAND chip supports on-die
ECC mode, by checking a number of conditions:
- It must be an ONFI NAND
- It must be a SLC NAND
- Enabling *and* disabling on-die ECC must work
- The on-die ECC must be correcting 4 bits per 512 bytes of data. Some
Micron NAND chips have an on-die ECC able to correct 8 bits per 512
bytes of data, but they work slightly differently and therefore we
don't support them in this patch.
Then, if the on-die ECC cannot be disabled (some Micron NAND have on-die
ECC forcefully enabled), we bail out, as we don't support such
NANDs. Indeed, the implementation of raw_read()/raw_write() make the
assumption that on-die ECC can be disabled. Support for Micron NANDs
with on-die ECC forcefully enabled can easily be added, but in the
absence of such HW for testing, we preferred to simply bail out.
If the on-die ECC is supported, and requested in the Device Tree, then
it is indeed enabled, by using custom implementations of the
->read_page(), ->read_page_raw(), ->write_page() and ->write_page_raw()
operation to properly handle the on-die ECC.
In the non-raw functions, we need to enable the internal ECC engine
before issuing the NAND_CMD_READ0 or NAND_CMD_SEQIN commands, which is
why we set the NAND_ECC_CUSTOM_PAGE_ACCESS option at initialization
time (it asks the NAND core to let the NAND driver issue those
commands).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
A lot of drivers are providing their own ->cmdfunc(), and most of the
time this implementation does not support all possible NAND operations.
But since ->cmdfunc() cannot return an error code, the core has no way
to know that the operation it requested is not supported.
This is a problem we cannot address for all kind of operations with the
current design, but we can prevent these silent failures for the
GET/SET FEATURES operation by overloading the default
->onfi_{set,get}_features() methods with one returning -ENOTSUPP.
Reported-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
|
|
Mauro says:
This patch series convert the remaining DocBooks to ReST.
The first version was originally
send as 3 patch series:
[PATCH 00/36] Convert DocBook documents to ReST
[PATCH 0/5] Convert more books to ReST
[PATCH 00/13] Get rid of DocBook
The lsm book was added as if it were a text file under
Documentation. The plan is to merge it with another file
under Documentation/security, after both this series and
a security Documentation patch series gets merged.
It also adjusts some Sphinx-pedantic errors/warnings on
some kernel-doc markups.
I also added some patches here to add PDF output for all
existing ReST books.
|
|
./drivers/mtd/nand/nand_bbt.c:1: warning: no structured comments found
./include/linux/mtd/nand.h:785: ERROR: Unexpected indentation.
./drivers/mtd/nand/nand_base.c:449: WARNING: Definition list ends without a blank line; unexpected unindent.
./drivers/mtd/nand/nand_base.c:1161: ERROR: Unexpected indentation.
./drivers/mtd/nand/nand_base.c:1162: WARNING: Block quote ends without a blank line; unexpected unindent.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This patch starts adding support to Octo SPI protocols (SPI x-y-8).
Op codes for Fast Read and/or Page Program operations using Octo SPI
protocols are not known yet (no JEDEC specification has defined them yet)
but we'd rather introduce the Octo SPI protocols now so it's done as it
should be.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
|
|
This patch introduces support to Double Transfer Rate (DTR) SPI protocols.
DTR is used only for Fast Read operations.
According to manufacturer datasheets, whatever the number of I/O lines
used during instruction (x) and address/mode/dummy (y) clock cycles, DTR
is used only during data (z) clock cycles of SPI x-y-z protocols.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
|
|
This patch changes the prototype of spi_nor_scan(): its 3rd parameter
is replaced by a 'struct spi_nor_hwcaps' pointer, which tells the spi-nor
framework about the actual hardware capabilities supported by the SPI
controller and its driver.
Besides, this patch also introduces a new 'struct spi_nor_flash_parameter'
telling the spi-nor framework about the hardware capabilities supported by
the SPI flash memory and the associated settings required to use those
hardware caps.
Then, to improve the readability of spi_nor_scan(), the discovery of the
memory settings and the memory initialization are now split into two
dedicated functions.
1 - spi_nor_init_params()
The spi_nor_init_params() function is responsible for initializing the
'struct spi_nor_flash_parameter'. Currently this structure is filled with
legacy values but further patches will allow to override some parameter
values dynamically, for instance by reading the JESD216 Serial Flash
Discoverable Parameter (SFDP) tables from the SPI memory.
The spi_nor_init_params() function only deals with the hardware
capabilities of the SPI flash memory: especially it doesn't care about
the hardware capabilities supported by the SPI controller.
2 - spi_nor_setup()
The second function is called once the 'struct spi_nor_flash_parameter'
has been initialized by spi_nor_init_params().
With both 'struct spi_nor_flash_parameter' and 'struct spi_nor_hwcaps',
the new argument of spi_nor_scan(), spi_nor_setup() computes the best
match between hardware caps supported by both the (Q)SPI memory and
controller hence selecting the relevant settings for (Fast) Read and Page
Program operations.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
|
|
The nand_read_page_raw() and nand_write_page_raw() functions might be
re-used by vendor-specific implementations of the read_page/write_page
functions. Instead of having vendor-specific code duplicate this code,
it is much better to export those functions and allow them to be
re-used.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
A number of NAND flashes have a capability called "on-die ECC" where the
NAND chip itself is capable of detecting and correcting errors.
Linux already has support for using the ECC implementation of the NAND
controller, or a software based ECC implementation, but not for using
the ECC implementation of the NAND controller. However, such an
implementation is sometimes useful in situations where the NAND
controller provides ECC algorithms that are not strong enough for the
NAND chip used on the system. A typical case is a NAND chip that
requires a 4-bit ECC, while the NAND controller only provides a 1-bit
ECC algorithm.
This commit introduces the support for the NAND_ECC_ON_DIE ECC mode:
- Parsing of the "on-die" value for the "nand-ecc-mode" Device Tree
property
- Handling NAND_ECC_ON_DIE case in nand_scan_tail(). The idea is that
the vendor specific code for the NAND chip must implement
->read_page() and ->write_page(). It may optionally provide its own
->read_page_raw() and ->write_page_raw() as well. For OOB operation,
we assume the standard operations are good enough, but they can be
overridden by the vendor specific code if needed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Pull MTD updates from Brian Norris:
"NAND, from Boris:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
SPI NOR, from Cyrille:
- fixes in the hisi, intel and Mediatek SPI controller drivers
- fixes to some SPI flash memories not supporting the Chip Erase
command.
- add support to some new memory parts (Winbond, Macronix, Micron,
ESMT).
- add new driver for the STM32 QSPI controller
And a few fixes for Gemini and Versatile platforms on physmap-of"
* tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits)
MAINTAINERS: Update NAND subsystem git repositories
mtd: nand: gpio: update binding
mtd: nand: add ooblayout for old hamming layout
mtd: oxnas_nand: Allocating more than necessary in probe()
dt-bindings: mtd: Document the STM32 QSPI bindings
mtd: mtk-nor: set controller's address width according to nor flash
mtd: spi-nor: add driver for STM32 quad spi flash controller
mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program
mtd: nand: davinci: add comment on NAND subpage write status on keystone
mtd: nand: omap2: Fix partition creation via cmdline mtdparts
mtd: nand: NULL terminate a of_device_id table
mtd: nand: Fix a couple error codes
mtd: nand: allow drivers to request minimum alignment for passed buffer
mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
mtd: nand: denali: allow to override revision number
mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
mtd: nand: denali_dt: remove dma-mask DT property
mtd: nand: denali: support 64bit capable DMA engine
mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
mtd: nand: denali: support HW_ECC_FIXUP capability
...
|
|
From Boris:
"""
This pull request contains:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
"""
|
|
In some cases, nand_do_{read,write}_ops is passed with unaligned
ops->datbuf. Drivers using DMA will be unhappy about unaligned
buffer.
The new struct member, buf_align, represents the minimum alignment
the driver require for the buffer. If the buffer passed from the
upper MTD layer does not have enough alignment, nand_do_*_ops will
use bufpoi.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The comment for ecc.read_page() requires that it should return
"0 if bitflips uncorrectable".
Actually, drivers could return positive values when uncorrectable
bitflips occur. For example, nand_read_page_swecc() is the case.
If ecc.correct() returns -EBADMSG for the first ECC sector, and
a positive value for the second one, nand_read_page_swecc() returns
a positive max_bitflips and increments ecc_stats.failed for the same
page.
The requirement can be relaxed by tweaking nand_do_read_ops().
Move the max_bitflips calculation below the retry.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The last/only user of the chip->write_page() hook (the Atmel NAND
controller driver) has been reworked and is no longer specifying a custom
->write_page() implementation.
Drop this hook before someone else start abusing it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
MTD already allocates backing_dev_info dynamically. Convert it to use
generic infrastructure for this including proper refcounting. We drop
mtd->backing_dev_info as its only use was to pass mtd_bdi pointer from
one file into another and if we wanted to keep that in a clean way, we'd
have to make mtd hold and drop bdi reference as needed which seems
pointless for passing one global pointer...
CC: David Woodhouse <dwmw2@infradead.org>
CC: Brian Norris <computersforpeace@gmail.com>
CC: linux-mtd@lists.infradead.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This allows better compile-time optimizations with CONFIG_OF disabled.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Move Macronix specific initialization logic into nand_macronix.c. This
is part of the "separate vendor specific code from core" cleanup
process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Move AMD/Spansion specific initialization/detection logic into
nand_amd.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
|
|
Move Micron specific initialization logic into nand_micron.c. This is
part of the "separate vendor specific code from core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
|
|
Move Toshiba specific initialization and detection logic into
nand_toshiba.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
|
|
Move Hynix specific initialization and detection logic into
nand_hynix.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
|
|
Move Samsung specific initialization and detection logic into
nand_samsung.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
|
|
A lot of NANDs are implementing generic features in a non-generic way,
or are providing advanced auto-detection logic where the NAND ID bytes
meaning changes with the NAND generation.
Providing this vendor specific initialization step will allow us to get
rid of full-id entries in the nand_ids table or all the vendor specific
cases added over the time in the generic NAND ID decoding logic.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
There is no reason to expose the NAND manufacturer table. Provide an
helper function to find manufacturers by their id.
We also turn the nand_manufacturers table into a const array, since its
members are not modified after the initial assignment.
Finally, we remove the sentinel manufacturer entry from the manufacturers
table (we already have the array size information given by ARRAY_SIZE()),
and add the nand_manufacturer_name() helper to handle the "Unknown" case
properly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Drop the 's' at the end of nand_manufacturers since the struct is actually
describing a single manufacturer, not a manufacturer table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Store the NAND ID in struct nand_chip to avoid passing id_data and id_len
as function parameters.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
|
|
Fix typos and add the following to the scripts/spelling.txt:
partiton||partition
Link: http://lkml.kernel.org/r/1481573103-11329-7-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This can be used to easily identify a specific chip on a system with
multiple chips.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
From Cyrille:
"""
This pull request contains the following notable changes:
- add support to the 4-byte address instruction set.
- add support to new memory parts.
- add support to S3AN memories.
- add support to the Intel SPI controller.
- add support to the Aspeed AST2400 and AST2550 controllers.
- fix max SPI transfer and message sizes in m25p80_read().
- fix the Candence QSPI driver.
- fix the Freescale QSPI driver.
"""
|
|
This patch renames the SPINOR_OP_* macros of the 4-byte address
instruction set so the new names all share a common pattern: the 4-byte
address name is built from the 3-byte address name appending the "_4B"
suffix.
The patch also introduces new op codes to support other SPI protocols such
as SPI 1-4-4 and SPI 1-2-2.
This is a transitional patch and will help a later patch of spi-nor.c
to automate the translation from the 3-byte address op codes into their
4-byte address version.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
|
|
Xilinx Spartan-3AN FPGAs contain an In-System Flash where they keep
their configuration data and (optionally) some user data.
The protocol of this flash follows most of the spi-nor standard. With
the following differences:
- Page size might not be a power of two.
- The address calculation (default addressing mode).
- The spi nor commands used.
Protocol is described on Xilinx User Guide UG333
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
|
|
The user visible change here is that mtd partitions get an of_node link
in sysfs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
From Boris:
"""
This pull request contains minor fixes/improvements on existing drivers:
- sunxi: avoid busy-waiting for NAND events
- ifc: fix ECC handling on IFC v1.0
- OX820: add explicit dependency on ARCH_OXNAS in Kconfig
- core: add a new manufacture ID and fix a kernel-doc warning
- fsmc: kill pdata support
- lpc32xx_slc: remove unneeded NULL check
"""
Conflicts:
include/linux/mtd/nand.h
[Brian: trivial conflict in the comment section]
|
|
The fields max_bb_per_die and blocks_per_die are useful determining the
number of bad blocks a MTD needs to allocate. How they are set will
depend on if the chip is ONFI, JEDEC or a full-id entry in the nand_ids
table.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electron.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
If implemented, 'max_bad_blocks' returns the maximum number of bad
blocks to reserve for a MTD. An implementation for NAND is coming soon.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electron.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Add WINBOND manufacturer id.
Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The FSMC driver has an execution path and a header file in
<linux/mtd/fsmc.h> that serves to support passing in platform
data through board files, albeit no upstream users of this
mechanism exist.
The header file also contains function headers for functions that
do not exist in the kernel.
Delete this and move the platform data struct, parsing and
handling into the driver, assume we are using OF and make the
driver depend on OF, remove the ifdefs making that optional.
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Fix kernel-doc warnings in <linux/mtd/nand.h>:
..//include/linux/mtd/nand.h:658: warning: No description found for parameter 'tCEH_min'
..//include/linux/mtd/nand.h:877: warning: No description found for parameter 'data_interface'
Fixes: eee64b700e26 ("mtd: nand: Introduce nand_data_interface")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
From Boris Brezillon:
"""
This pull request contains the following notable changes:
- new tango NAND controller driver
- new ox820 NAND controller driver
- addition of a new full-ID entry in the nand_ids table
- rework of the s3c240 driver to support DT
- extension of the nand_sdr_timings to expose tCCS, tPROG and tR
- addition of a new flag to ask the core to wait for tCCS when sending
a RNDIN/RNDOUT command
- addition of a new flag to ask the core to let the controller driver
send the READ/PROGPAGE command
This pull request also contains minor fixes/cleanup/cosmetic changes:
- properly support 512 ECC step size in the sunxi driver
- improve the error messages in the pxa probe path
- fix module autoload in the omap2 driver
- cleanup of several nand drivers to return nand_scan{_tail}() error
code instead of returning -EIO
- various cleanups in the denali driver
- cleanups in the ooblayout handling (MTD core)
- fix an error check in nandsim
"""
|
|
If your controller already sends the required NAND commands when
reading or writing a page, then the framework is not supposed to
send READ0 and SEQIN/PAGEPROG respectively.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Drivers implementing ->cmd_ctrl() and relying on the default ->cmdfunc()
implementation usually don't wait tCCS when a column change (RNDIN or
RNDOUT) is requested.
Add an option flag to ask the core to do so (note that we keep this as
an opt-in to avoid breaking existing implementations), and make use of
the ->data_interface information is available (otherwise, wait 500ns).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
|
|
Add the tR_max, tBERS_max, tPROG_max and tCCS_min timings to the
nand_sdr_timings struct.
Assign default/safe values for the statically defined timings, and
extract them from the ONFI parameter table if the NAND is ONFI
compliant.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
|
