| Age | Commit message (Collapse) | Author |
|---|
|
After driver split, no need for debugfs callback, remove those
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
If an interface type changes from a type that is
only supported on the PAN context (e.g. P2P GO)
to a type that is supported on the BSS context,
and the BSS context is not in use, then we need
to use the BSS context instead of changing the
device type within the context. To achieve this,
refuse the type change, which causes a down/up
cycle that will allocate the BSS context for the
interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
The current RXON checking doesn't verify that
the channel is valid (or at least non-zero),
so add that. Also, add a WARN() so we get a
stacktrace, and capture a bitmask of errors
in order to capture all necessary information
in the warning itself (in case the previous
messages are snipped off.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
This header file isn't used, and if we ever need
these definitions they shouldn't be added to a
driver but rather to the common 802.11 include
file that has all frame definitions. Thus, just
remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
All agn devices use the same eeprom semaphore and calib version routines.
Delete the indirection and move the semaphore routines to where they are
used and make static.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
All agn devices use the same module parameter structure. Delete the
indirection and access the structure diretly.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Correction for new 105 series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
New microcode versions use the good CRC threshold
field differently, as a flag, and in that case we
should set it to 1/0 instead of 1/65535 for an
active/passive scan.
The new behaviour is advertised by the uCode with
a feature flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
No functional changes, separate the connect and disconnect sequences in
RXON commit function, easier to read and understand.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
The data structure is shared by all _agn devices, remove the reference to 5000
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Move rxon_assoc to static function from ops
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
The WoWLAN resume code will have to essentially
do a restart, but without going through the work
struct. To support that, refactor the restart by
splitting out the preparation code into a new
function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
There are a few cases like the WoWLAN support
I'm writing that require attempting to access
the NIC when it is known that it might not be
accessible, e.g. after the system woke up and
the platform might have reset the device.
To avoid messages in this case, introduce the
new function iwl_grab_nic_access_silent(), it
will only return an error status.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
If a device error happens while the uCode is
being loaded or initialised, we will attempt
to restart the device (which will likely fail
again, but that's not the issue here). During
this new restart, we turn off the device, but
as the uCode failed to initialise it already
is turned off. As a consequence, grabbing NIC
access will fail and cause excessive messages
and hangs.
To fix this issue, introduce a new status bit
and only attempt to reprogram the device when
it isn't already disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
This makes sure that one cannot request a 99Mbps full-duplex and get a
100Mbps half-duplex configuration in return due to the way the
speed/duplex parameters are handled internally.
Tested: e1000 works
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initial driver reported different speeds depending on the port being
used. This advertises the speed to be 10Mbps in any case, which is
what it actually is on the wire.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This tells the NIC to take the speed specified by ethtool into account
when configuring the NIC, instead of keeping the previous speed.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.
For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.
All drivers compiled with make allyesconfig ion x86_64 have been
updated.
Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This makes sure the ethtool's set_settings() callback of network
drivers don't ignore the 16 most significant bits when ethtool calls
their set_settings().
All drivers compiled with make allyesconfig on x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).
This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.
All drivers visible to make allyesconfig under x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support of pause frames advertise in mii_get_an. This provides all drivers
that use mii_ethtool_gset to represent their own and Link partner flow control
abilities in ethtool.
Signed-off-by: Artem Polyakov <artpol84@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable setting speed and auto negotiation parameters for GbE ports.
Hardware do not support half duplex setting currently.
o Update driver version to 5.0.17.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Support ethtool command ETHTOOL_GCHANNELS and ETHTOOL_SCHANNELS.
o Number of rcv rings configuration depend upon number of msix vector.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For backward compatibility, we should retain the module parameters and
sysfs attributes to control the number of peer notifications
(gratuitous ARPs and unsolicited NAs) sent after bonding failover.
Also, it is possible for failover to take place even though the new
active slave does not have link up, and in that case the peer
notification should be deferred until it does.
Change ipv4 and ipv6 so they do not automatically send peer
notifications on bonding failover.
Change the bonding driver to send separate NETDEV_NOTIFY_PEERS
notifications when the link is up, as many times as requested. Since
it does not directly control which protocols send notifications, make
num_grat_arp and num_unsol_na aliases for a single parameter. Bump
the bonding version number and update its documentation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Adam Jaremko <adam.jaremko@gmail.com>
Acked-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some newer Huawei devices (T-Mobile Rocket, others) have cdc-ether
compatible ports, so recognize and expose them.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tx_headroom required for mwl8k driver is 32 bytes and it
can use the space for 802.11 header received from mac80211.
mwl8k considers the smallest 802.11 frame (CTS2self of 10
bytes) that can be received from mac80211 to compute the
extra_tx_headroom as 22 (32 - 10) bytes.
When the wireless interface is part of bridge, this
extra_tx_headroom requirement results in a memcpy in
mac80211 (in function pskb_expand_head) for all the data
frames needing L2 forwarding/bridging, when NET_SKB_PAD is
defined as 32. This patch reduces the extra_tx_headroom by
8 bytes so that memcpy of data frames in mac80211 is
avoided in this case.
The resize will be required in driver for frames with 802.11
header size of less than 18 bytes.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove all the convoluted hacks in the driver and simplify things
by making use of mac80211's LED triggers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We now use priv->mutex to serialize sync command, remove old
priv->sync_cmd_mutex and add assertion that priv->mutex must be locked.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Check status bits with mutex taken, because when we wait for mutex
unlock, status can change. Patch should also make remaining sync
commands be send with priv->mutex taken. That will prevent execute
these commands when we are currently reset firmware, what could
possibly cause troubles.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We mark command as huge by using meta->flags from other (non huge) command,
but flags can be possibly overridden, when non huge command is enqueued,
what can lead to:
WARNING: at lib/dma-debug.c:696 dma_debug_device_change+0x1a3/0x1f0()
DMA-API: device driver has pending DMA allocations while released from device [count=1]
To fix introduce additional CMD_MAPPED to mark command as mapped and
serialize iwl_enqueue_hcmd() with iwl_tx_cmd_complete() using
hcmd_lock. Serialization will also fix possible race conditions,
because q->read_ptr, q->write_ptr are modified/used in parallel.
Do not change callback, I did (and fixed) that mistake in iwlagn.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
struct iwl_queue is not part of firmware interface, so __packed is not
needed. Remove it since is may affect performance.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We never set STATUS_SCANNING in softwre scanning mode, disable_hw_scan
check is unneeded. Correct debug message while at it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Don't need to use conditional as ch->band is already assigned to
IEEE80211_BAND_5GHZ or IEEE80211_BAND_2GHZ
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add two below iwlwifi commits to iwlegacy:
commit 554d1d027b19265c4aa3f718b3126d2b86e09a08
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Thu Dec 23 12:38:21 2010 +0100
iwlagn: enable only rfkill interrupt when device is down
commit 3dd823e6b86407aed1a025041d8f1df77e43a9c8
Author: Don Fry <donald.h.fry@intel.com>
Date: Sun Feb 6 09:29:45 2011 -0800
iwlagn: Re-enable RF_KILL interrupt when down
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since
commit f844a709a7d8f8be61a571afc31dfaca9e779621
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Fri Jan 28 16:47:44 2011 +0100
iwlwifi: do not set tx power when channel is changing
we set device tx power during initialization to priv->tx_power_next,
which itself is initialized to minimum power. That changed
default behaviour of driver. Previously we initialized device to
transmit at maximum available power by default. Patch change again
to previous behaviour and cleanup tx power initialization.
Fortunately this is not critical fix, as mac80211 layer setup
tx power lately to 14dB, hence device does not operate at minimal
transmit power all the time.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Debugfs file location: <debugfs_mnt>/ieee80211/phy#/ath9k_htc/modal_eeprom
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Debugfs file location: <debugfs_mnt>/ieee80211/phy#/ath9k_htc/base_eeprom
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This oops was recently reported to me:
invalid opcode: 0000 [#1] SMP
last sysfs file:
/sys/devices/pci0000:00/0000:00:01.0/0000:01:0d.0/0000:02:05.0/device
CPU 1
Modules linked in: bnx2(+) sunrpc ipv6 dm_mirror dm_region_hash dm_log sg
microcode serio_raw amd64_edac_mod edac_core edac_mce_amd k8temp i2c_piix4
shpchp ext4 mbcache jbd2 sd_mod crc_t10dif mptsas mptscsih mptbase
scsi_transport_sas radeon ttm drm_kms_helper drm hwmon i2c_algo_bit i2c_core
dm_mod [last unloaded: bnx2]
Modules linked in: bnx2(+) sunrpc ipv6 dm_mirror dm_region_hash dm_log sg
microcode serio_raw amd64_edac_mod edac_core edac_mce_amd k8temp i2c_piix4
shpchp ext4 mbcache jbd2 sd_mod crc_t10dif mptsas mptscsih mptbase
scsi_transport_sas radeon ttm drm_kms_helper drm hwmon i2c_algo_bit i2c_core
dm_mod [last unloaded: bnx2]
Pid: 23900, comm: pidof Not tainted 2.6.32-130.el6.x86_64 #1 BladeCenter LS21
-[797251Z]-
RIP: 0010:[<ffffffffa058b270>] [<ffffffffa058b270>] 0xffffffffa058b270
RSP: 0018:ffff880002083e48 EFLAGS: 00010246
RAX: ffff880002083e90 RBX: ffff88007ccd4000 RCX: 0000000000000000
RDX: 0000000000000100 RSI: dead000000200200 RDI: ffff8800007b8700
RBP: ffff880002083ed0 R08: ffff88000208db40 R09: 0000022d191d27c8
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800007b9bc8
R13: ffff880002083e90 R14: ffff8800007b8700 R15: ffffffffa058b270
FS: 00007fbb3bcf7700(0000) GS:ffff880002080000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000001664a98 CR3: 0000000060395000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process pidof (pid: 23900, threadinfo ffff8800007e8000, task ffff8800091c0040)
Stack:
ffffffff81079f77 ffffffff8109e010 ffff88007ccd5c20 ffff88007ccd5820
<0> ffff88007ccd5420 ffff8800007e9fd8 ffff8800007e9fd8 0000010000000000
<0> ffff88007ccd5020 ffff880002083e90 ffff880002083e90 ffffffff8102a00d
Call Trace:
<IRQ>
[<ffffffff81079f77>] ? run_timer_softirq+0x197/0x340
[<ffffffff8109e010>] ? tick_sched_timer+0x0/0xc0
[<ffffffff8102a00d>] ? lapic_next_event+0x1d/0x30
[<ffffffff8106f737>] __do_softirq+0xb7/0x1e0
[<ffffffff81092cc0>] ? hrtimer_interrupt+0x140/0x250
[<ffffffff81185f90>] ? filldir+0x0/0xe0
[<ffffffff8100c2cc>] call_softirq+0x1c/0x30
[<ffffffff8100df05>] do_softirq+0x65/0xa0
[<ffffffff8106f525>] irq_exit+0x85/0x90
[<ffffffff814e3340>] smp_apic_timer_interrupt+0x70/0x9b
[<ffffffff8100bc93>] apic_timer_interrupt+0x13/0x20
<EOI>
[<ffffffff81211ba5>] ? selinux_file_permission+0x45/0x150
[<ffffffff81262a75>] ? _atomic_dec_and_lock+0x55/0x80
[<ffffffff812050c6>] security_file_permission+0x16/0x20
[<ffffffff811861c1>] vfs_readdir+0x71/0xe0
[<ffffffff81186399>] sys_getdents+0x89/0xf0
[<ffffffff8100b172>] system_call_fastpath+0x16/0x1b
It occured during some stress testing, in which the reporter was repeatedly
removing and modprobing the bnx2 module while doing various other random
operations on the bnx2 registered net device. Noting that this error occured on
a serdes based device, we noted that there were a few ethtool operations (most
notably self_test and set_phys_id) that have execution paths that lead into
bnx2_setup_serdes_phy. This function is notable because it executes a mod_timer
call, which starts the bp->timer running. Currently bnx2 is setup to assume
that this timer only nees to be stopped when bnx2_close or bnx2_suspend is
called. Since the above ethtool operations are not gated on the net device
having been opened however, that assumption is incorrect, and can lead to the
timer still running after the module has been removed, leading to the oops above
(as well as other simmilar oopses).
Fix the problem by ensuring that the timer is stopped when pci_device_unregister
is called.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Hushan Jia <hjia@redhat.com>
CC: Michael Chan <mchan@broadcom.com>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CC [M] drivers/net/wireless/p54/eeprom.o
drivers/net/wireless/p54/eeprom.c: In function ‘p54_parse_rssical’:
drivers/net/wireless/p54/eeprom.c:494:8: warning: ‘freq’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
CC [M] drivers/net/wireless/mwifiex/join.o
drivers/net/wireless/mwifiex/join.c: In function ‘mwifiex_cmd_802_11_associate’:
drivers/net/wireless/mwifiex/join.c:119:8: warning: ‘tsf_val’ may be used uninitialized in this function
drivers/net/wireless/mwifiex/join.c:103:12: note: ‘tsf_val’ was declared here
Looks like a copy-n-paste error, identical lines are a few lines below
the ones removed, with an actual memcpy to tsf_val in between...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
CC [M] drivers/net/wireless/b43/phy_n.o
drivers/net/wireless/b43/phy_n.c: In function ‘b43_nphy_set_channel’:
drivers/net/wireless/b43/phy_n.c:3848:47: warning: ‘tabent_r2’ may be used uninitialized in this function
drivers/net/wireless/b43/phy_n.c:3849:47: warning: ‘tabent_r3’ may be used uninitialized in this function
drivers/net/wireless/b43/phy_n.c: In function ‘b43_nphy_poll_rssi.clone.14’:
drivers/net/wireless/b43/phy_n.c:2270:6: warning: ‘save_regs_phy$7’ may be used uninitialized in this function
drivers/net/wireless/b43/phy_n.c:2270:6: warning: ‘save_regs_phy$8’ may be used uninitialized in this function
FWIW, the usage of these variables is goverened by checks that match
their initializations. So, I think these are actually false warnings.
Still, I would rather avoid the warning SPAM...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
CC [M] drivers/net/wireless/ath/ath5k/reset.o
drivers/net/wireless/ath/ath5k/reset.c: In function ‘ath5k_hw_init_core_clock’:
drivers/net/wireless/ath/ath5k/reset.c:100:51: warning: ‘txf2txs’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Need to use broadcast sta_id for management frames, otherwise we broke
BA session in the firmware and get messages like that:
"Received BA when not expected"
or (on older kernels):
"BA scd_flow 0 does not match txq_id 10"
This fix regression introduced in 2.6.35 during station management
code rewrite by:
commit 2a87c26bbe9587baeb9e56d3ce0b4971bd777643
Author: Johannes Berg <johannes.berg@intel.com>
Date: Fri Apr 30 11:30:45 2010 -0700
iwlwifi: use iwl_find_station less
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Need to use broadcast sta_id for management frames, otherwise we broke
BA session in the firmware and get messages like that:
"Received BA when not expected"
or (on older kernels):
"BA scd_flow 0 does not match txq_id 10"
This fix regression introduced in 2.6.35 during station management
code rewrite by:
commit 2a87c26bbe9587baeb9e56d3ce0b4971bd777643
Author: Johannes Berg <johannes.berg@intel.com>
Date: Fri Apr 30 11:30:45 2010 -0700
iwlwifi: use iwl_find_station less
Patch partially resolve:
https://bugzilla.kernel.org/show_bug.cgi?id=16691
However, there are still 11n performance problems on 4965 and 5xxx
devices that need to be investigated.
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit b9367bf3ee6d ("net: ibmveth: convert to hw_features") accidentally
removed call to ibmveth_set_csum_offload() in ibmveth_probe(). Put the
call back where it was, but with additional error checking provided
by ibmveth_set_features().
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
[sfr: dev -> netdev]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Memory allocated in ETHTOOL_ACTIVE mode, is not getting freed. So,
in ETHTOOL_ID_INACTIVE mode, return after freeing allocated memory.
o Using set bit instead of blink_down field, as it is also required
in internal Loopback test and etc.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
