| Age | Commit message (Collapse) | Author |
|---|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
i40e driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx element.
e1000 driver runs Tx completion polling cycle right before the Rx
one. Now that e1000 uses napi_consume_skb() to put skbuff_heads of
completed entries into the cache, it will never empty and always
warm at that moment. Switch to the napi_build_skb() to relax mm
pressure on heavy Rx and increase throughput.
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In order to take the best from per-cpu NAPI skbuff_head caches and
CPU cycles, let's switch from dev_kfree_skb_any(), which passes skb
back to the mm layer, to napi_consume_skb(), which feeds those
caches on non-zero budget instead (falls back to the former on 0).
Do the replacement in e1000_unmap_and_free_tx_resource(). There are
4 call sites of this function throughout the driver:
* e1000_clean_tx_ring(). Slowpath, process context, cleans the
whole Tx ring on ifdown. Use budget of 0 here;
* e1000_tx_map(). Hotpath, net Tx softirq, unmaps the buffers in
case of error. Use 0 as well;
* e1000_clean_tx_irq(). Hotpath, NAPI Tx completion polling cycle.
As the driver doesn't count completed Tx entries towards the NAPI
budget, just use the poll budget of 64 to utilize caches.
Apart from being a preparation for switching to napi_build_skb(),
this is useful on its own as well, as napi_consume_skb() flushes
skb caches by batches of 32 instead of one-at-a-time.
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Delete the initialization of three static variables
because it is meaningless.
Signed-off-by: Wen Zhiwei <wenzhiwei@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq() for DT users only.
While at it propagate error code in case request_irq() fails instead of
returning -EBUSY.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq(). While doing so return error pointer
from read_dts_node() as platform_get_irq() may return -EPROBE_DEFER.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are seeing spurious wakeup caused by Intel 7560 WWAN on AMD laptops.
This prevent those laptops to stay in s2idle state.
>From what I can understand, the intention of ipc_pcie_suspend() is to
put the device to D3cold, and ipc_pcie_suspend_s2idle() is to keep the
device at D0. However, the device can still be put to D3hot/D3cold by
PCI core.
So explicitly let PCI core know this device should stay at D0, to solve
the spurious wakeup.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pci_pm_suspend_noirq() and pci_pm_resume_noirq() already handle power
transition for system-wide suspend and resume, so it's not necessary to
do it in the driver.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The blamed commit changed the vlan used by the host ports to be 4095
instead of 0.
Because of this change the following issues are seen:
- when the port is probed first it was adding an entry in the MAC table
with the wrong vlan (port->pvid which is default 0) and not HOST_PVID
- when the port is removed from a bridge, it was using the wrong vlan to
add entries in the MAC table. It was using the old PVID and not the
HOST_PVID
This patch fixes this two issues by using the HOST_PVID instead of
port->pvid.
Fixes: 6d2c186afa5d5d ("net: lan966x: Add vlan support.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If NETIF_F_GRO_HW is disabled, the existing driver code uses kmalloc'ed
data for RX buffers. This causes inefficient SW GRO performance
because the GRO data is merged using the less efficient frag_list.
Use netdev_alloc_frag() and friends instead so that GRO data can be
merged into skb_shinfo(skb)->frags for better performance.
[Use skb_free_frag() - Vikas Gupta]
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The xdp_do_flush_map function has been replaced with the more general
xdp_do_flush().
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support showing and setting the CQE mode in ethtool.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CQE coalescing mode is the same as the timer reset coalescing mode
on Broadcom devices. Currently this mode is always enabled if it
is supported by the device. Restructure the code slightly to support
dynamically changing this mode.
Add a flags field to struct bnxt_coal. Initially, the CQE flag will
be set for the RX and TX side if the device supports it. We need to
move bnxt_init_dflt_coal() to set up default coalescing until the
capability is determined.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
5750X (P5) chips handle receiving packets on the NQ rather than the main
completion queue so we need to get and set stats from the correct spots
for dynamic interrupt moderation.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Log the unrecognized error report type value as well.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW has been modified to send a new async event when it detects
a pause storm. Register for this new event and log it upon receipt.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add config_init for LAN8814. This function is required for the following
reasons:
- we need to make sure that the PHY is reset,
- disable ANEG with QSGMII PCS Host side
- swap the MDI-X A,B transmit so that there will not be any link flip-flaps
when the PHY gets a link.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the possessive "its" instead of the contraction of "it is" ("it's")
in user messages.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
include/net/sock.h
commit 8f905c0e7354 ("inet: fully convert sk->sk_rx_dst to RCU rules")
commit 43f51df41729 ("net: move early demux fields close to sk_refcnt")
https://lore.kernel.org/all/20211222141641.0caa0ab3@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ETHER_CLK_SEL_FREQ_SEL_2P5M is not 0 bit of the register. This is a
value, which is 0. Fix from BIT(0) to 0.
Reported-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Fixes: b38dd98ff8d0 ("net: stmmac: Add Toshiba Visconti SoCs glue driver")
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Link: https://lore.kernel.org/r/20211223073633.101306-1-nobuhiro1.iwamatsu@toshiba.co.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are some chances that the actual base of hardware is different
from the value recorded by driver, so we have to reset the variable
of ocp_base to sync it.
Set ocp_base to -1. Then, it would be updated and the new base would be
set to the hardware next time.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It needs to set mdio force mode. Otherwise, link off always occurs when
setting force speed.
Fixes: 195aae321c82 ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert the u32 variable to type u64 in a context where expression of
type u64 is required to avoid potential overflow.
Fixes: e9e3720002f6 ("net: stmmac: ptp: update tas basetime after ptp adjust")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Link: https://lore.kernel.org/r/20211223073928.37371-1-xiaoliang.yang_1@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit d3256efd8e8b ("veth: allow enabling NAPI even without XDP"),
if GRO is enabled on a veth device and TSO is disabled on the peer
device, TCP skbs will go through the NAPI callback. If there is no XDP
program attached, the veth code does not perform any share check, and
shared/cloned skbs could enter the GRO engine.
Ignat reported a BUG triggered later-on due to the above condition:
[ 53.970529][ C1] kernel BUG at net/core/skbuff.c:3574!
[ 53.981755][ C1] invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
[ 53.982634][ C1] CPU: 1 PID: 19 Comm: ksoftirqd/1 Not tainted 5.16.0-rc5+ #25
[ 53.982634][ C1] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
[ 53.982634][ C1] RIP: 0010:skb_shift+0x13ef/0x23b0
[ 53.982634][ C1] Code: ea 03 0f b6 04 02 48 89 fa 83 e2 07 38 d0
7f 08 84 c0 0f 85 41 0c 00 00 41 80 7f 02 00 4d 8d b5 d0 00 00 00 0f
85 74 f5 ff ff <0f> 0b 4d 8d 77 20 be 04 00 00 00 4c 89 44 24 78 4c 89
f7 4c 89 8c
[ 53.982634][ C1] RSP: 0018:ffff8881008f7008 EFLAGS: 00010246
[ 53.982634][ C1] RAX: 0000000000000000 RBX: ffff8881180b4c80 RCX: 0000000000000000
[ 53.982634][ C1] RDX: 0000000000000002 RSI: ffff8881180b4d3c RDI: ffff88810bc9cac2
[ 53.982634][ C1] RBP: ffff8881008f70b8 R08: ffff8881180b4cf4 R09: ffff8881180b4cf0
[ 53.982634][ C1] R10: ffffed1022999e5c R11: 0000000000000002 R12: 0000000000000590
[ 53.982634][ C1] R13: ffff88810f940c80 R14: ffff88810f940d50 R15: ffff88810bc9cac0
[ 53.982634][ C1] FS: 0000000000000000(0000) GS:ffff888235880000(0000) knlGS:0000000000000000
[ 53.982634][ C1] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 53.982634][ C1] CR2: 00007ff5f9b86680 CR3: 0000000108ce8004 CR4: 0000000000170ee0
[ 53.982634][ C1] Call Trace:
[ 53.982634][ C1] <TASK>
[ 53.982634][ C1] tcp_sacktag_walk+0xaba/0x18e0
[ 53.982634][ C1] tcp_sacktag_write_queue+0xe7b/0x3460
[ 53.982634][ C1] tcp_ack+0x2666/0x54b0
[ 53.982634][ C1] tcp_rcv_established+0x4d9/0x20f0
[ 53.982634][ C1] tcp_v4_do_rcv+0x551/0x810
[ 53.982634][ C1] tcp_v4_rcv+0x22ed/0x2ed0
[ 53.982634][ C1] ip_protocol_deliver_rcu+0x96/0xaf0
[ 53.982634][ C1] ip_local_deliver_finish+0x1e0/0x2f0
[ 53.982634][ C1] ip_sublist_rcv_finish+0x211/0x440
[ 53.982634][ C1] ip_list_rcv_finish.constprop.0+0x424/0x660
[ 53.982634][ C1] ip_list_rcv+0x2c8/0x410
[ 53.982634][ C1] __netif_receive_skb_list_core+0x65c/0x910
[ 53.982634][ C1] netif_receive_skb_list_internal+0x5f9/0xcb0
[ 53.982634][ C1] napi_complete_done+0x188/0x6e0
[ 53.982634][ C1] gro_cell_poll+0x10c/0x1d0
[ 53.982634][ C1] __napi_poll+0xa1/0x530
[ 53.982634][ C1] net_rx_action+0x567/0x1270
[ 53.982634][ C1] __do_softirq+0x28a/0x9ba
[ 53.982634][ C1] run_ksoftirqd+0x32/0x60
[ 53.982634][ C1] smpboot_thread_fn+0x559/0x8c0
[ 53.982634][ C1] kthread+0x3b9/0x490
[ 53.982634][ C1] ret_from_fork+0x22/0x30
[ 53.982634][ C1] </TASK>
Address the issue by skipping the GRO stage for shared or cloned skbs.
To reduce the chance of OoO, try to unclone the skbs before giving up.
v1 -> v2:
- use avoid skb_copy and fallback to netif_receive_skb - Eric
Reported-by: Ignat Korchagin <ignat@cloudflare.com>
Fixes: d3256efd8e8b ("veth: allow enabling NAPI even without XDP")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Ignat Korchagin <ignat@cloudflare.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/b5f61c5602aab01bac8d711d8d1bfab0a4817db7.1640197544.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
Third set of patches for v5.17, and the final one if all goes well. We
have Specific Absorption Rate (SAR) support for both mt76 and rtw88.
Also iwlwifi should be now W=1 warning free. But otherwise nothing
really special this time, business as usual.
Major changes:
mt76
* Specific Absorption Rate (SAR) support
* mt7921: new PCI ids
* mt7921: 160 MHz channel support
iwlwifi
* fix W=1 and sparse warnings
* BNJ hardware support
* add new killer device ids
* support for Time-Aware-SAR (TAS) from the BIOS
* Optimized Connectivity Experience (OCE) scan support
rtw88
* hardware scan
* Specific Absorption Rate (SAR) support
ath11k
* qca6390/wcn6855: report signal and tx bitrate
* qca6390: rfkill support
* qca6390/wcn6855: regdb.bin support
ath5k
* switch to rate table based lookup
wilc1000
* spi: reset/enable GPIO support
* tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (148 commits)
mt76: mt7921: fix a possible race enabling/disabling runtime-pm
wilc1000: Document enable-gpios and reset-gpios properties
wilc1000: Add reset/enable GPIO support to SPI driver
wilc1000: Convert static "chipid" variable to device-local variable
rtw89: 8852a: correct bit definition of dfs_en
rtw88: don't consider deep PS mode when transmitting packet
ath11k: Fix unexpected return buffer manager error for QCA6390
ath11k: add support of firmware logging for WCN6855
ath11k: Fix napi related hang
ath10k: replace strlcpy with strscpy
rtw88: support SAR via kernel common API
rtw88: 8822c: add ieee80211_ops::hw_scan
iwlwifi: mei: wait before mapping the shared area
iwlwifi: mei: clear the ownership when the driver goes down
iwlwifi: yoyo: fix issue with new DBGI_SRAM region read.
iwlwifi: fw: fix some scan kernel-doc
iwlwifi: pcie: make sure prph_info is set when treating wakeup IRQ
iwlwifi: mvm: remove card state notification code
iwlwifi: mvm: drop too short packets silently
iwlwifi: mvm: fix AUX ROC removal
...
====================
Link: https://lore.kernel.org/r/20211223141108.78808C36AE9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds basic support for EtherType RX frame steering for
LLDP and PTP using the hardware offload capabilities.
Example steps for setting up RX frame steering for LLDP and PTP:
$ IFDEVNAME=eth0
$ tc qdisc add dev $IFDEVNAME ingress
$ tc qdisc add dev $IFDEVNAME root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 0 0 0 0 0 0 0 0 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0
For LLDP
$ tc filter add dev $IFDEVNAME parent ffff: protocol 0x88cc \
flower hw_tc 5
OR
$ tc filter add dev $IFDEVNAME parent ffff: protocol LLDP \
flower hw_tc 5
For PTP
$ tc filter add dev $IFDEVNAME parent ffff: protocol 0x88f7 \
flower hw_tc 6
Show tc ingress filter
$ tc filter show dev $IFDEVNAME ingress
v1->v2:
Thanks to Kurt's and Sebastian's suggestion.
- change from __be16 to u16 etype
- change ETHER_TYPE_FULL_MASK to use cpu_to_be16() macro
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch series extends the current supported bridge flags with the
following flags: BR_FLOOD, BR_BCAST_FLOOD and BR_LEARNING.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spectrum ASICs do not support matching of VLAN ID at egress.
Currently, mlxsw driver forbids matching of all VLAN related fields at
egress, which is too strict check.
For example, the following filter is not supported by the driver:
$ tc filter add dev swpX egress protocol 802.1q pref 1 handle 101 flower
vlan_ethtype ipv4 src_ip .. dst_ip .. skip_sw action pass
Error: mlxsw_spectrum: vlan_id key is not supported on egress.
We have an error talking to the kernel
The filter above does not match on VLAN ID, but is bounced anyway.
Make the check more specific, forbid only matching of 'vlan_id' at egress.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-12-21
1) From Shay Drory: Devlink user knobs to control device's EQ size
This series provides knobs which will enable users to
minimize memory consumption of mlx5 Functions (PF/VF/SF).
mlx5 exposes two new generic devlink params for EQ size
configuration and uses devlink generic param max_macs.
LINK: https://lore.kernel.org/netdev/20211208141722.13646-1-shayd@nvidia.com/
2) From Tariq and Lama, allocate software channel objects and statistics
of a mlx5 netdevice private data dynamically upon first demand to save on
memory.
* tag 'mlx5-updates-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Take packet_merge params directly from the RX res struct
net/mlx5e: Allocate per-channel stats dynamically at first usage
net/mlx5e: Use dynamic per-channel allocations in stats
net/mlx5e: Allow profile-specific limitation on max num of channels
net/mlx5e: Save memory by using dynamic allocation in netdev priv
net/mlx5e: Add profile indications for PTP and QOS HTB features
net/mlx5e: Use bitmap field for profile features
net/mlx5: Remove the repeated declaration
net/mlx5: Let user configure max_macs generic param
devlink: Clarifies max_macs generic devlink param
net/mlx5: Let user configure event_eq_size param
devlink: Add new "event_eq_size" generic device param
net/mlx5: Let user configure io_eq_size param
devlink: Add new "io_eq_size" generic device param
====================
Link: https://lore.kernel.org/r/20211222031604.14540-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit d068ca2ae2e6 ("codel: split into multiple files") moved all
Qdisc-related code to codel_qdisc.h, move the include of pkt_sched.h
as well.
This is similar to the previous commit, although we don't care as
much about incremental builds after pkt_sched.h was touched itself
it is included by net/sch_generic.h which is modified ~20 times
a year.
This decreases the incremental build size after touching pkt_sched.h
from 1592 to 617 objects.
Fix unmasked missing includes in WiFi drivers.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221193941.3805147-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since sock.h is modified relatively often (60 times in the last
12 months) it seems worthwhile to decrease the incremental build
work.
CoDel's header includes net/inet_ecn.h which in turn includes net/sock.h.
codel.h is itself included by mac80211 which is included by much of
the WiFi stack and drivers. Removing the net/inet_ecn.h include from
CoDel breaks the dependecy between WiFi and sock.h.
Commit d068ca2ae2e6 ("codel: split into multiple files") moved all
the code which actually needs ECN helpers out to net/codel_impl.h,
the include can be moved there as well.
This decreases the incremental build size after touching sock.h
from 4999 objects to 4051 objects.
Fix unmasked missing includes in WiFi drivers.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221193941.3805147-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The variable bytes is being used to summate slot lengths,
however the value is never used afterwards. The summation
is redundant so remove variable bytes.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211222003937.727325-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix an odd indent where some code was left indented, and causes smatch
to warn:
ice_log_pkg_init() warn: inconsistent indenting
While here, for consistency, add a break after the default case.
This commit has a Fixes: but we caught this while it was only in net-next.
Fixes: 247dd97d713c ("ice: Refactor status flow for DDP load")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20211221230538.2546315-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If asix_read_cmd() returns 0 on 30th interation, 0 will be returned from
asix_check_host_enable(), which is logically wrong. Fix it by returning
-ETIMEDOUT explicitly if we have exceeded 30 iterations
Also, replaced 30 with #define as suggested by Andrew
Fixes: a786e3195d6a ("net: asix: fix uninit value bugs")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/ecd3470ce6c2d5697ac635d0d3b14a47defb4acb.1640117288.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
asix_read_cmd() may read less than sizeof(smsr) bytes and in this case
smsr will be uninitialized.
Fail log:
BUG: KMSAN: uninit-value in asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline]
BUG: KMSAN: uninit-value in asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline] drivers/net/usb/asix_common.c:497
BUG: KMSAN: uninit-value in asix_mdio_read+0x3c1/0xb00 drivers/net/usb/asix_common.c:497 drivers/net/usb/asix_common.c:497
asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline]
asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline] drivers/net/usb/asix_common.c:497
asix_mdio_read+0x3c1/0xb00 drivers/net/usb/asix_common.c:497 drivers/net/usb/asix_common.c:497
Fixes: d9fe64e51114 ("net: asix: Add in_pm parameter")
Reported-and-tested-by: syzbot+f44badb06036334e867a@syzkaller.appspotmail.com
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/8966e3b514edf39857dd93603fc79ec02e000a75.1640117288.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-12-21
This series contains updates to ice driver only.
Karol modifies the reset flow to correct issues with PTP reset.
Jake extends PTP support for E822 based devices. This includes a few
cleanup patches, that fix some minor issues. In addition, there are some
slight refactors to ease the addition of E822 support, followed by adding
the new hardware implementation ice_ptp_hw.c.
There are a few major differences with E822 support compared to E810
support:
*) The E822 device has a Clock Generation Unit which must be initialized in
order to generate proper clock frequencies on the output that drives the PTP
hardware clock registers
*) The E822 PHY is a bit different and requires a more complex
initialization procedure which must be rerun any time the link configuration
changes.
*) The E822 devices support enhanced timestamp calibration by making use of
a process called Vernier offset measurement. This allows the hardware to
measure phase offset related to the PHY clocks for Serdes and FEC, reducing
the inaccuracy of the timestamp relative to the actual packet transmission
and receipt. Making use of this requires data gathered from the first
transmitted and received packets, and waiting for the PHY to complete the
calibration measurements. This is done as part of a new kthread, ov_work.
Note that to avoid delay in enabling timestamps, we start the PHY in
'bypass' mode which allows timestamps to be captured without the Vernier
calibration measurement. Once the first packets have been sent and received,
we then complete the calibration setup and exit bypass mode and begin using
the more precise timestamps. According to the datasheet, timestamps without
calibration data can be incorrect relative to actual receipt or transmission
by up to 1 clock cycle (~1.25 nanoseconds), while calibrated timestamps
should be correct to within 1/8th of a clock cycle (~0.15 nanoseconds).
*) E822 devices support crosstimestamping via PCIe PTM, which we enable when
available on the platform.
There is a fair amount of logic required to perform PHY and CGU
initialization, which is the vast majority of the new code, but it is fairly
self contained within ice_ptp_hw.c, with the exception of monitoring for
offset validity being handled by a kthread.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: support crosstimestamping on E822 devices if supported
ice: exit bypass mode once hardware finishes timestamp calibration
ice: ensure the hardware Clock Generation Unit is configured
ice: implement basic E822 PTP support
ice: convert clk_freq capability into time_ref
ice: introduce ice_ptp_init_phc function
ice: use 'int err' instead of 'int status' in ice_ptp_hw.c
ice: PTP: move setting of tstamp_config
ice: introduce ice_base_incval function
ice: Fix E810 PTP reset flow
====================
Link: https://lore.kernel.org/r/20211221174845.3063640-1-anthony.l.nguyen@intel.com
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Because of the possible failure of the kcalloc, it should be better to
set rx_queue->page_ptr_mask to 0 when it happens in order to maintain
the consistency.
Fixes: 5a6681e22c14 ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20211220140344.978408-1-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Because of the possible failure of the kcalloc, it should be better to
set rx_queue->page_ptr_mask to 0 when it happens in order to maintain
the consistency.
Fixes: 5a6681e22c14 ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20211220135603.954944-1-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix a possible race enabling/disabling runtime-pm between
mt7921_pm_set() and mt7921_poll_rx() since mt7921_pm_wake_work()
always schedules rx-napi callback and it will trigger
mt7921_pm_power_save_work routine putting chip to in low-power state
during mt7921_pm_set processing.
Suggested-by: Deren Wu <deren.wu@mediatek.com>
Tested-by: Deren Wu <deren.wu@mediatek.com>
Fixes: 1d8efc741df8 ("mt76: mt7921: introduce Runtime PM support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/0f3e075a2033dc05f09dab4059e5be8cbdccc239.1640094847.git.lorenzo@kernel.org
|
|
For the SDIO driver, the RESET/ENABLE pins of WILC1000 are controlled
through the SDIO power sequence driver. This commit adds analogous
support for the SPI driver. Specifically, during initialization, the
chip will be ENABLEd and taken out of RESET and during
deinitialization, the chip will be placed back into RESET and disabled
(both to reduce power consumption and to ensure the WiFi radio is
off).
Both RESET and ENABLE GPIOs are optional. However, if the ENABLE GPIO
is specified, then the RESET GPIO should normally also be specified as
otherwise there is no way to ensure proper timing of the ENABLE/RESET
sequence.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221212531.4011609-2-davidm@egauge.net
|
|
Move "chipid" variable into the per-driver structure so the code
doesn't break if more than one wilc1000 module is present.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221210538.4011227-1-davidm@egauge.net
|
|
Since there are other protections in the set channel flow, fortunately old
wrong setting won't affect the performance.
Signed-off-by: Chung-Hsuan Hung <hsuan8331@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221024800.23814-1-pkshih@realtek.com
|
|
In original flow, driver needs to ensure chip leave deep ps mode
before transmitting any packet, and don't enter deep ps mode beofre
PCIE DMA is finished. Now with the support of 8822ce's hardware
setting and firmware after v9.9.11, these limits are removed.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221020230.20764-1-pkshih@realtek.com
|
|
ath.git patches for v5.17. Major changes:
ath11k
* qca6390/wcn6855: report signal and tx bitrate
* qca6390: rfkill support
* qca6390/wcn6855: regdb.bin support
ath5k
* switch to rate table based lookup
|
|
We are seeing below error on QCA6390:
...
[70211.671189] ath11k_pci 0000:72:00.0: failed to parse rx error in wbm_rel ring desc -22
[70212.696154] ath11k_pci 0000:72:00.0: failed to parse rx error in wbm_rel ring desc -22
[70213.092941] ath11k_pci 0000:72:00.0: failed to parse rx error in wbm_rel ring desc -22
...
The reason is that, with commit 734223d78428 ("ath11k: change return
buffer manager for QCA6390"), ath11k expects the return buffer manager
(RBM) field of descriptor configured as HAL_RX_BUF_RBM_SW1_BM when
parsing error frames from WBM2SW3_RELEASE ring. This is a wrong change
cause the RBM field is set as HAL_RX_BUF_RBM_SW3_BM.
The same issue also applies to REO2TCL ring though we have not got any
error reported.
Fix it by changing RBM from HAL_RX_BUF_RBM_SW1_BM to HAL_RX_BUF_RBM_SW3_BM
for these two rings.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Fixes: 734223d78428 ("ath11k: change return buffer manager for QCA6390")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211222013536.582527-1-quic_bqiang@quicinc.com
|
|
Because platform_get_irq() could fail and return error irq.
Therefore, it might be better to check it if order to avoid the use of
error irq.
Fixes: 797047f875b5 ("net: ks8851: Implement Parallel bus operations")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
