| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is a small set of tty and serial driver updates for 6.11-rc1. Not
much happened this cycle, unlike the previous kernel release which had
lots of "excitement" in this part of the kernel. Included in here are
the following changes:
- dt binding updates for new platforms
- 8250 driver updates
- various small serial driver fixes and updates
- printk/console naming and matching attempt #2 (was reverted for
6.10-final, should be good to go this time around, acked by the
relevant maintainers).
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (22 commits)
Documentation: kernel-parameters: Add DEVNAME:0.0 format for serial ports
serial: core: Add serial_base_match_and_update_preferred_console()
printk: Add match_devname_and_update_preferred_console()
serial: sc16is7xx: hardware reset chip if reset-gpios is defined in DT
dt-bindings: serial: sc16is7xx: add reset-gpios
dt-bindings: serial: vt8500-uart: convert to json-schema
serial: 8250_platform: Explicitly show we initialise ISA ports only once
tty: add missing MODULE_DESCRIPTION() macros
dt-bindings: serial: mediatek,uart: add MT7988
serial: sh-sci: Add support for RZ/V2H(P) SoC
dt-bindings: serial: Add documentation for Renesas RZ/V2H(P) (R9A09G057) SCIF support
dt-bindings: serial: renesas,scif: Make 'interrupt-names' property as required
dt-bindings: serial: renesas,scif: Validate 'interrupts' and 'interrupt-names'
dt-bindings: serial: renesas,scif: Move ref for serial.yaml at the end
riscv: dts: starfive: jh7110: Add the core reset and jh7110 compatible for uarts
serial: 8250_dw: Use reset array API to get resets
dt-bindings: serial: snps-dw-apb-uart: Add one more reset signal for StarFive JH7110 SoC
serial: 8250: Extract platform driver
serial: 8250: Extract RSA bits
serial: imx: stop casting struct uart_port to struct imx_port
...
|
|
Let's add serial_base_match_and_update_preferred_console() for consoles
using DEVNAME:0.0 style naming.
The earlier approach to add it caused issues in the kernel command line
ordering as we were calling __add_preferred_console() again for the
deferred consoles.
Signed-off-by: Tony Lindgren <tony.lindgren@linux.intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Tested-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20240703100615.118762-3-tony.lindgren@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Qualcomm GENI serial driver did not handle buffer flushing and used
to print discarded characters when the circular buffer was cleared.
Since commit 1788cf6a91d9 ("tty: serial: switch from circ_buf to kfifo")
this instead resulted in a hard lockup due to
qcom_geni_serial_send_chunk_fifo() spinning indefinitely in the
interrupt handler.
The underlying bugs have now been fixed, but make sure to output NUL
characters instead of killing the machine if a similar driver bug is
ever reintroduced.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240704101805.30612-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Qualcomm GENI serial driver does not handle buffer flushing and used
to continue printing discarded characters when the circular buffer was
cleared. Since commit 1788cf6a91d9 ("tty: serial: switch from circ_buf
to kfifo") this instead results in a hard lockup due to
qcom_geni_serial_send_chunk_fifo() spinning indefinitely in the
interrupt handler.
This is easily triggered by interrupting a command such as dmesg in a
serial console but can also happen when stopping a serial getty on
reboot.
Implement the flush_buffer() callback and use it to cancel any active TX
command when the write buffer has been emptied.
Reported-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/lkml/20240610222515.3023730-1-dianders@chromium.org/
Fixes: 1788cf6a91d9 ("tty: serial: switch from circ_buf to kfifo")
Fixes: a1fee899e5be ("tty: serial: qcom_geni_serial: Fix softlock")
Cc: stable@vger.kernel.org # 5.0
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240704101805.30612-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The stop_tx() callback is used to implement software flow control and
must not discard data as the Qualcomm GENI driver is currently doing
when there is an active TX command.
Cancelling an active command can also leave data in the hardware FIFO,
which prevents the watermark interrupt from being enabled when TX is
later restarted. This results in a soft lockup and is easily triggered
by stopping TX using software flow control in a serial console but this
can also happen after suspend.
Fix this by only stopping any active command, and effectively clearing
the hardware fifo, when shutting down the port. When TX is later
restarted, a transfer command may need to be issued to discard any stale
data that could prevent the watermark interrupt from firing.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 4.17
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240704101805.30612-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a process is killed while writing to a /dev/ttymxc* device in RS485
mode, we observe that the RTS signal is left high, thus making it
impossible for other devices to transmit anything.
Moreover, the ->tx_state variable is left in state SEND, which means
that when one next opens the device and configures baud rate etc., the
initialization code in imx_uart_set_termios dutifully ensures the RTS
pin is pulled down, but since ->tx_state is already SEND, the logic in
imx_uart_start_tx() does not in fact pull the pin high before
transmitting, so nothing actually gets on the wire on the other side
of the transceiver. Only when that transmission is allowed to complete
is the state machine then back in a consistent state.
This is completely reproducible by doing something as simple as
seq 10000 > /dev/ttymxc0
and hitting ctrl-C, and watching with a logic analyzer.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: stable <stable@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20240625184206.508837-1-linux@rasmusvillemoes.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The pdev->dev.of_node can be NULL if the "serial" node is absent.
Add a NULL check to return an error in such cases.
Fixes: 930cbf92db01 ("tty: serial: Add Nuvoton ma35d1 serial driver support")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/8df7ce45-fd58-4235-88f7-43fe7cd67e8f@moroto.mountain/
Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240625064128.127-1-ychuang570808@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Errata i2310[0] says, Erroneous timeout can be triggered,
if this Erroneous interrupt is not cleared then it may leads
to storm of interrupts.
Commit 9d141c1e6157 ("serial: 8250_omap: Implementation of Errata i2310")
which added the workaround but missed ensuring RX FIFO is really empty
before applying the errata workaround as recommended in the errata text.
Fix this by adding back check for UART_OMAP_RX_LVL to be 0 for
workaround to take effect.
[0] https://www.ti.com/lit/pdf/sprz536 page 23
Fixes: 9d141c1e6157 ("serial: 8250_omap: Implementation of Errata i2310")
Cc: stable@vger.kernel.org
Reported-by: Vignesh Raghavendra <vigneshr@ti.com>
Closes: https://lore.kernel.org/all/e96d0c55-0b12-4cbf-9d23-48963543de49@ti.com/
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240625160725.2102194-1-u-kumar1@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With commit a81dbd0463ec ("serial: imx: set receiver level before
starting uart") we set the receiver level to its default value. This
caused a regression when using SDMA, where the receiver level is 9
instead of 8 (default). This change will first check if the receiver
level is zero and only then set it to the default. This still avoids the
interrupt storm when the receiver level is zero.
Fixes: a81dbd0463ec ("serial: imx: set receiver level before starting uart")
Cc: stable <stable@kernel.org>
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Link: https://lore.kernel.org/r/20240703112543.148304-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This resolves the merge issues in the 8250 code due to some reverts in
6.10-rc6 in the console changes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial / console fixes from Greg KH:
"Here are a bunch of fixes/reverts for 6.10-rc6. Include in here are:
- revert the bunch of tty/serial/console changes that landed in -rc1
that didn't quite work properly yet.
Everyone agreed to just revert them for now and will work on making
them better for a future release instead of trying to quick fix the
existing changes this late in the release cycle
- 8250 driver port count bugfix
- Other tiny serial port bugfixes for reported issues
All of these have been in linux-next this week with no reported
issues"
* tag 'tty-6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "printk: Save console options for add_preferred_console_match()"
Revert "printk: Don't try to parse DEVNAME:0.0 console options"
Revert "printk: Flag register_console() if console is set on command line"
Revert "serial: core: Add support for DEVNAME:0.0 style naming for kernel console"
Revert "serial: core: Handle serial console options"
Revert "serial: 8250: Add preferred console in serial8250_isa_init_ports()"
Revert "Documentation: kernel-parameters: Add DEVNAME:0.0 format for serial ports"
Revert "serial: 8250: Fix add preferred console for serial8250_isa_init_ports()"
Revert "serial: core: Fix ifdef for serial base console functions"
serial: bcm63xx-uart: fix tx after conversion to uart_port_tx_limited()
serial: core: introduce uart_port_tx_limited_flags()
Revert "serial: core: only stop transmit when HW fifo is empty"
serial: imx: set receiver level before starting uart
tty: mcf: MCF54418 has 10 UARTS
serial: 8250_omap: Implementation of Errata i2310
tty: serial: 8250: Fix port count mismatch with the device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening fixes from Kees Cook:
- Remove invalid tty __counted_by annotation (Nathan Chancellor)
- Add missing MODULE_DESCRIPTION()s for KUnit string tests (Jeff
Johnson)
- Remove non-functional per-arch kstack entropy filtering
* tag 'hardening-v6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
tty: mxser: Remove __counted_by from mxser_board.ports[]
randomize_kstack: Remove non-functional per-arch entropy filtering
string: kunit: add missing MODULE_DESCRIPTION() macros
|
|
Work for __counted_by on generic pointers in structures (not just
flexible array members) has started landing in Clang 19 (current tip of
tree). During the development of this feature, a restriction was added
to __counted_by to prevent the flexible array member's element type from
including a flexible array member itself such as:
struct foo {
int count;
char buf[];
};
struct bar {
int count;
struct foo data[] __counted_by(count);
};
because the size of data cannot be calculated with the standard array
size formula:
sizeof(struct foo) * count
This restriction was downgraded to a warning but due to CONFIG_WERROR,
it can still break the build. The application of __counted_by on the
ports member of 'struct mxser_board' triggers this restriction,
resulting in:
drivers/tty/mxser.c:291:2: error: 'counted_by' should not be applied to an array with element of unknown size because 'struct mxser_port' is a struct type with a flexible array member. This will be an error in a future compiler version [-Werror,-Wbounds-safety-counted-by-elt-type-unknown-size]
291 | struct mxser_port ports[] __counted_by(nports);
| ^~~~~~~~~~~~~~~~~~~~~~~~~
1 error generated.
Remove this use of __counted_by to fix the warning/error. However,
rather than remove it altogether, leave it commented, as it may be
possible to support this in future compiler releases.
Cc: <stable@vger.kernel.org>
Closes: https://github.com/ClangBuiltLinux/linux/issues/2026
Fixes: f34907ecca71 ("mxser: Annotate struct mxser_board with __counted_by")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240529-drop-counted-by-ports-mxser-board-v1-1-0ab217f4da6d@kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
console"
This reverts commit 787a1cabac01c99846070fcf702e53befaf89f79.
Let's roll back all of the serial core and printk console changes that
went into 6.10-rc1 as there still are problems with them that need to be
sorted out.
Link: https://lore.kernel.org/r/ZnpRozsdw6zbjqze@tlindgre-MOBL1
Reported-by: Petr Mladek <pmladek@suse.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit a0f32e2dd99867b164bfebcf36729c2a0d41b30b.
Let's roll back all of the serial core and printk console changes that
went into 6.10-rc1 as there still are problems with them that need to be
sorted out.
Link: https://lore.kernel.org/r/ZnpRozsdw6zbjqze@tlindgre-MOBL1
Reported-by: Petr Mladek <pmladek@suse.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit a8b04cfe7dad84e65df5996e14b435fd356fe62c.
Let's roll back all of the serial core and printk console changes that
went into 6.10-rc1 as there still are problems with them that need to be
sorted out.
Link: https://lore.kernel.org/r/ZnpRozsdw6zbjqze@tlindgre-MOBL1
Reported-by: Petr Mladek <pmladek@suse.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 4547cd76f08a6f301f6ad563f5d0e4566924ec6b.
Let's roll back all of the serial core and printk console changes that
went into 6.10-rc1 as there still are problems with them that need to be
sorted out.
Link: https://lore.kernel.org/r/ZnpRozsdw6zbjqze@tlindgre-MOBL1
Reported-by: Petr Mladek <pmladek@suse.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit b20172ca6bf489534892b801a5db41bbf5ceec75.
Let's roll back all of the serial core and printk console changes that
went into 6.10-rc1 as there still are problems with them that need to be
sorted out.
Link: https://lore.kernel.org/r/ZnpRozsdw6zbjqze@tlindgre-MOBL1
Reported-by: Petr Mladek <pmladek@suse.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When bcm63xx-uart was converted to uart_port_tx_limited(), it implicitly
added a call to stop_tx(). This causes garbage to be put out on the
serial console. To fix this, pass UART_TX_NOSTOP in flags, and manually
call stop_tx() ourselves analogue to how a similar issue was fixed in
commit 7be50f2e8f20 ("serial: mxs-auart: fix tx").
Fixes: d11cc8c3c4b6 ("tty: serial: use uart_port_tx_limited()")
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Doug Brown <doug@schmorgal.com>
Link: https://lore.kernel.org/r/20240606195632.173255-4-doug@schmorgal.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Set the receiver level to something > 0 before calling imx_uart_start_rx
in rs485_config. This is necessary to avoid an interrupt storm that
might prevent the system from booting. This was seen on an i.MX7 device
when the rs485-rts-active-low property was active in the device tree.
Fixes: 6d215f83e5fc ("serial: imx: warn user when using unsupported configuration")
Cc: stable <stable@kernel.org>
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Link: https://lore.kernel.org/r/20240621153829.183780-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Most of the colfires have up to 5 UARTs but MCF54418 has up-to 10 !
Change the maximum value authorized.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@yoseli.org>
Cc: stable <stable@kernel.org>
Fixes: 2545cf6e94b4 ("m68knommu: allow 4 coldfire serial ports")
Link: https://lore.kernel.org/r/20240620-upstream-uart-v1-1-a9d0d95fb19e@yoseli.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As per Errata i2310[0], Erroneous timeout can be triggered,
if this Erroneous interrupt is not cleared then it may leads
to storm of interrupts, therefore apply Errata i2310 solution.
[0] https://www.ti.com/lit/pdf/sprz536 page 23
Fixes: b67e830d38fa ("serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240619105903.165434-1-u-kumar1@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Normally, the number of ports is indicated by the third digit of the
device ID on Moxa PCI serial boards. For example, `0x1121` indicates a
device with 2 ports.
However, `CP116E_A_A` and `CP116E_A_B` are exceptions; they have 8
ports, but the third digit of the device ID is `6`.
This patch introduces a function to retrieve the number of ports on Moxa
PCI serial boards, addressing the issue described above.
Fixes: 37058fd5d239 ("tty: serial: 8250: Add support for MOXA Mini PCIe boards")
Cc: stable <stable@kernel.org>
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240617063058.18866-1-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some boards connect a GPIO to the reset pin, and the reset pin needs
to be set up correctly before accessing the chip.
Add a function to handle the chip reset. If the reset-gpios is defined
in the DT, do hardware reset through this GPIO, otherwise do software
reset as before.
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20240618112620.152848-2-hui.wang@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
serial8250_isa_init_ports() uses home grown approach to make itself
a singleton. Instead, explicitly show that we initialise ISA ports
once by providing a helper function which calls the original function
via DO_ONCE() macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240606184841.3102545-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/8250/8250_base.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/8250/8250_pxa.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/8250/serial_cs.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/esp32_uart.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/esp32_acm.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/owl-uart.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/n_hdlc.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/n_gsm.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/ttynull.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/goldfish.o
Add all missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240607-md-drivers-tty-v1-1-50a7efb8bed8@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add serial support for RZ/V2H(P) SoC with earlycon.
The SCIF interface in the Renesas RZ/V2H(P) is similar to that available
in the RZ/G2L (R9A07G044) SoC, with the following differences:
- RZ/V2H(P) SoC has three additional interrupts: one for Tx end/Rx ready
and two for Rx and Tx buffer full, all of which are edge-triggered.
- RZ/V2H(P) supports asynchronous mode, whereas RZ/G2L supports both
synchronous and asynchronous modes.
- There are differences in the configuration of certain registers such
as SCSMR, SCFCR, and SCSPTR between the two SoCs.
To handle these differences on RZ/V2H(P) SoC SCIx_RZV2H_SCIF_REGTYPE
is added.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240604170513.522631-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some SoCs like StarFive JH7110 require two or more resets.
So change to use the reset array API to get resets.
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Link: https://lore.kernel.org/r/20240604084729.57239-3-hal.feng@starfivetech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
syzbot is reporting lockdep warning upon
int disc = 7;
ioctl(open("/dev/ttyS3", O_RDONLY), TIOCSETD, &disc);
sequence. Do like what commit 5f1149d2f4bf ("serial: drop debugging
WARN_ON_ONCE() from uart_put_char()") does.
Reported-by: syzbot+f78380e4eae53c64125c@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=f78380e4eae53c64125c
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/d775ae2d-a2ac-439e-8e2b-134749f60f30@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit d49216438139
("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
removed Kconfig SPI_MASTER or I2C dependency for SERIAL_SC16IS7XX (core).
This removal was done because I inadvertently misinterpreted some review
comments.
Because of that, the driver question now pops up if both I2C and
SPI_MASTER are disabled.
Re-add Kconfig SPI_MASTER or I2C dependency to fix the problem.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: d49216438139 ("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240603152601.3689319-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit d49216438139
("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
renamed SERIAL_SC16IS7XX_CORE by SERIAL_SC16IS7XX. This means that some
configs should have been updated when I submitted the original patch, but
unfortunately they were not. Geert mentioned for example:
arch/mips/configs/cu1??0-neo_defconfig
Rename SERIAL_SC16IS7XX to SERIAL_SC16IS7XX_CORE so that existing configs
will still work correctly.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: d49216438139 ("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240603152601.3689319-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Recently, suspend testing on sc7180-trogdor based devices has started
to sometimes fail with messages like this:
port a88000.serial:0.0: PM: calling pm_runtime_force_suspend+0x0/0xf8 @ 28934, parent: a88000.serial:0
port a88000.serial:0.0: PM: dpm_run_callback(): pm_runtime_force_suspend+0x0/0xf8 returns -16
port a88000.serial:0.0: PM: pm_runtime_force_suspend+0x0/0xf8 returned -16 after 33 usecs
port a88000.serial:0.0: PM: failed to suspend: error -16
I could reproduce these problems by logging in via an agetty on the
debug serial port (which was _not_ used for kernel console) and
running:
cat /var/log/messages
...and then (via an SSH session) forcing a few suspend/resume cycles.
Tracing through the code and doing some printf()-based debugging shows
that the -16 (-EBUSY) comes from the recently added
serial_port_runtime_suspend().
The idea of the serial_port_runtime_suspend() function is to prevent
the port from being _runtime_ suspended if it still has bytes left to
transmit. Having bytes left to transmit isn't a reason to block
_system_ suspend, though. If a serdev device in the kernel needs to
block system suspend it should block its own suspend and it can use
serdev_device_wait_until_sent() to ensure bytes are sent.
The DEFINE_RUNTIME_DEV_PM_OPS() used by the serial_port code means
that the system suspend function will be pm_runtime_force_suspend().
In pm_runtime_force_suspend() we can see that before calling the
runtime suspend function we'll call pm_runtime_disable(). This should
be a reliable way to detect that we're called from system suspend and
that we shouldn't look for busyness.
Fixes: 43066e32227e ("serial: port: Don't suspend if the port is still busy")
Cc: stable@vger.kernel.org
Reviewed-by: Tony Lindgren <tony.lindgren@linux.intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240531080914.v3.1.I2395e66cf70c6e67d774c56943825c289b9c13e4@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The FIFO is 64 bytes, but the FCR is configured to fire the TX interrupt
when the FIFO is half empty (bit 3 = 0). Thus, we should only write 32
bytes when a TX interrupt occurs.
This fixes a problem observed on the PXA168 that dropped a bunch of TX
bytes during large transmissions.
Fixes: ab28f51c77cd ("serial: rewrite pxa2xx-uart to use 8250_core")
Signed-off-by: Doug Brown <doug@schmorgal.com>
Link: https://lore.kernel.org/r/20240519191929.122202-1-doug@schmorgal.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit d9666dfb314e1ffd6eb9c3c4243fe3e094c047a7.
The container of the struct dw8250_port_data is private to the actual
driver. In particular, 8250_lpss and 8250_dw use different data types
that are assigned to the UART port private_data. Hence, it must not
be used outside the specific driver.
Fix the mistake made in the past by moving the respective definitions
to the specific driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240514190730.2787071-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The container of the struct dw8250_port_data is private to the actual
driver. In particular, 8250_lpss and 8250_dw use different data types
that are assigned to the UART port private_data. Hence, it must not
be used outside the specific driver.
Currently the only cpr_val is required by the common code, make it
be available via struct dw8250_port_data.
This fixes the UART breakage on Intel Galileo boards.
Fixes: 593dea000bc1 ("serial: 8250: dw: Allow to use a fallback CPR value if not synthesized")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240514190730.2787071-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When lookahead has "consumed" some characters (la_count > 0),
n_tty_receive_buf_standard() and n_tty_receive_buf_closing() for
characters beyond the la_count are given wrong cp/fp offsets which
leads to duplicating and losing some characters.
If la_count > 0, correct buffer pointers and make count consistent too
(the latter is not strictly necessary to fix the issue but seems more
logical to adjust all variables immediately to keep state consistent).
Reported-by: Vadym Krevs <vkrevs@yahoo.com>
Fixes: 6bb6fa6908eb ("tty: Implement lookahead to process XON/XOFF timely")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218834
Tested-by: Vadym Krevs <vkrevs@yahoo.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240514140429.12087-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Extract platform driver to a separate module for better maintenance
and to reduce churn on 8250_core part changes when it's solely related
to the former. No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Sunil V L <sunilvl@ventanamicro.com>
Tested-by: Sunil V L <sunilvl@ventanamicro.com>
Link: https://lore.kernel.org/r/20240506140308.4040735-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Extract RSA bits to a separate module for better maintenance
and to reduce a churn on 8250_core part changes when it's solely
related to the former. No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240506140308.4040735-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
struct imx_port does have a struct uart_port as its first member, so
the current code works, but it is not how kernel code is usually
written.
Similar to many other serial drivers, introduce and use a
to_imx_port() helper based on container_of(). No functional change.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20240528094022.2161066-1-linux@rasmusvillemoes.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A LED trigger's activate() callback gets called when the LED trigger
gets activated for a specific LED, so that the trigger code can ensure
the LED state matches the current state of the trigger condition.
led_trigger_event() is intended for trigger condition state changes and
iterates over _all_ LEDs which are controlled by this trigger changing
the brightness of each of them.
In the activate() case only the brightness of the LED which is being
activated needs to change and that LED is passed as an argument to
activate(), switch to led_set_brightness() to only change the brightness
of the LED being activated.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240511152030.4848-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add `__free` function attribute to `ap` and `match` pointer
initialisations which ensure that the pointers are freed as soon as they
go out of scope, thus removing the need to manually free them using
`of_node_put`.
This also removes the need for the `goto` statement and the `rc`
variable.
Suggested-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Shresth Prasad <shresthprasad7@gmail.com>
Link: https://lore.kernel.org/r/20240518114051.18125-3-shresthprasad7@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small TTY and Serial driver fixes that missed the
6.9-final merge window, but have been in my tree for weeks (my fault,
travel caused me to miss this)
These fixes include:
- more n_gsm fixes for reported problems
- 8520_mtk driver fix
- 8250_bcm7271 driver fix
- sc16is7xx driver fix
All of these have been in linux-next for weeks without any reported
problems"
* tag 'tty-6.10-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sc16is7xx: fix bug in sc16is7xx_set_baud() when using prescaler
serial: 8250_bcm7271: use default_mux_rate if possible
serial: 8520_mtk: Set RTS on shutdown for Rx in-band wakeup
tty: n_gsm: fix missing receive state reset after mode switch
tty: n_gsm: fix possible out-of-bounds in gsm0_receive()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty/serial driver changes for 6.10-rc1.
Included in here are:
- Usual good set of api cleanups and evolution by Jiri Slaby to make
the serial interfaces move out of the 1990's by using kfifos
instead of hand-rolling their own logic.
- 8250_exar driver updates
- max3100 driver updates
- sc16is7xx driver updates
- exar driver updates
- sh-sci driver updates
- tty ldisc api addition to help refuse bindings
- other smaller serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (113 commits)
serial: Clear UPF_DEAD before calling tty_port_register_device_attr_serdev()
serial: imx: Raise TX trigger level to 8
serial: 8250_pnp: Simplify "line" related code
serial: sh-sci: simplify locking when re-issuing RXDMA fails
serial: sh-sci: let timeout timer only run when DMA is scheduled
serial: sh-sci: describe locking requirements for invalidating RXDMA
serial: sh-sci: protect invalidating RXDMA on shutdown
tty: add the option to have a tty reject a new ldisc
serial: core: Call device_set_awake_path() for console port
dt-bindings: serial: brcm,bcm2835-aux-uart: convert to dtschema
tty: serial: uartps: Add support for uartps controller reset
arm64: zynqmp: Add resets property for UART nodes
dt-bindings: serial: cdns,uart: Add optional reset property
serial: 8250_pnp: Switch to DEFINE_SIMPLE_DEV_PM_OPS()
serial: 8250_exar: Keep the includes sorted
serial: 8250_exar: Make type of bit the same in exar_ee_*_bit()
serial: 8250_exar: Use BIT() in exar_ee_read()
serial: 8250_exar: Switch to use dev_err_probe()
serial: 8250_exar: Return directly from switch-cases
serial: 8250_exar: Decrease indentation level
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Alexander Gordeev:
- Switch read and write software bits for PUDs
- Add missing hardware bits for PUDs and PMDs
- Generate unwind information for C modules to fix GDB unwind error for
vDSO functions
- Create .build-id links for unstripped vDSO files to enable vDSO
debugging with symbols
- Use standard stack frame layout for vDSO generated stack frames to
manually walk stack frames without DWARF information
- Rework perf_callchain_user() and arch_stack_walk_user() functions to
reduce code duplication
- Skip first stack frame when walking user stack
- Add basic checks to identify invalid instruction pointers when
walking stack frames
- Introduce and use struct stack_frame_vdso_wrapper within vDSO user
wrapper code to automatically generate an asm-offset define. Also use
STACK_FRAME_USER_OVERHEAD instead of STACK_FRAME_OVERHEAD to document
that the code works with user space stack
- Clear the backchain of the extra stack frame added by the vDSO user
wrapper code. This allows the user stack walker to detect and skip
the non-standard stack frame. Without this an incorrect instruction
pointer would be added to stack traces.
- Rewrite psw_idle() function in C to ease maintenance and further
enhancements
- Remove get_vtimer() function and use get_cpu_timer() instead
- Mark psw variable in __load_psw_mask() as __unitialized to avoid
superfluous clearing of PSW
- Remove obsolete and superfluous comment about removed TIF_FPU flag
- Replace memzero_explicit() and kfree() with kfree_sensitive() to fix
warnings reported by Coccinelle
- Wipe sensitive data and all copies of protected- or secure-keys from
stack when an IOCTL fails
- Both do_airq_interrupt() and do_io_interrupt() functions set
CIF_NOHZ_DELAY flag. Move it in do_io_irq() to simplify the code
- Provide iucv_alloc_device() and iucv_release_device() helpers, which
can be used to deduplicate more or less identical IUCV device
allocation and release code in four different drivers
- Make use of iucv_alloc_device() and iucv_release_device() helpers to
get rid of quite some code and also remove a cast to an incompatible
function (clang W=1)
- There is no user of iucv_root outside of the core IUCV code left.
Therefore remove the EXPORT_SYMBOL
- __apply_alternatives() contains a runtime check which verifies that
the size of the to be patched code area is even. Convert this to a
compile time check
- Increase size of buffers for sending z/VM CP DIAGNOSE X'008' commands
from 128 to 240
- Do not accept z/VM CP DIAGNOSE X'008' commands longer than maximally
allowed
- Use correct defines IPL_BP_NVME_LEN and IPL_BP0_NVME_LEN instead of
IPL_BP_FCP_LEN and IPL_BP0_FCP_LEN ones to initialize NVMe reIPL
block on 'scp_data' sysfs attribute update
- Initialize the correct fields of the NVMe dump block, which were
confused with FCP fields
- Refactor macros for 'scp_data' (re-)IPL sysfs attribute to reduce
code duplication
- Introduce 'scp_data' sysfs attribute for dump IPL to allow tools such
as dumpconf passing additional kernel command line parameters to a
stand-alone dumper
- Rework the CPACF query functions to use the correct RRE or RRF
instruction formats and set instruction register fields correctly
- Instead of calling BUG() at runtime force a link error during compile
when a unsupported opcode is used with __cpacf_query() or
__cpacf_check_opcode() functions
- Fix a crash in ap_parse_bitmap_str() function on /sys/bus/ap/apmask
or /sys/bus/ap/aqmask sysfs file update with a relative mask value
- Fix "bindings complete" udev event which should be sent once all AP
devices have been bound to device drivers and again when unbind/bind
actions take place and all AP devices are bound again
- Facility list alt_stfle_fac_list is nowhere used in the decompressor,
therefore remove it there
- Remove custom kprobes insn slot allocator in favour of the standard
module_alloc() one, since kernel image and module areas are located
within 4GB
- Use kvcalloc() instead of kvmalloc_array() in zcrypt driver to avoid
calling memset() with a large byte count and get rid of the sparse
warning as result
* tag 's390-6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (39 commits)
s390/zcrypt: Use kvcalloc() instead of kvmalloc_array()
s390/kprobes: Remove custom insn slot allocator
s390/boot: Remove alt_stfle_fac_list from decompressor
s390/ap: Fix bind complete udev event sent after each AP bus scan
s390/ap: Fix crash in AP internal function modify_bitmap()
s390/cpacf: Make use of invalid opcode produce a link error
s390/cpacf: Split and rework cpacf query functions
s390/ipl: Introduce sysfs attribute 'scp_data' for dump ipl
s390/ipl: Introduce macros for (re)ipl sysfs attribute 'scp_data'
s390/ipl: Fix incorrect initialization of nvme dump block
s390/ipl: Fix incorrect initialization of len fields in nvme reipl block
s390/ipl: Do not accept z/VM CP diag X'008' cmds longer than max length
s390/ipl: Fix size of vmcmd buffers for sending z/VM CP diag X'008' cmds
s390/alternatives: Convert runtime sanity check into compile time check
s390/iucv: Unexport iucv_root
tty: hvc-iucv: Make use of iucv_alloc_device()
s390/smsgiucv_app: Make use of iucv_alloc_device()
s390/netiucv: Make use of iucv_alloc_device()
s390/vmlogrdr: Make use of iucv_alloc_device()
s390/iucv: Provide iucv_alloc_device() / iucv_release_device()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Skip E820 checks for MCFG ECAM regions for new (2016+) machines,
since there's no requirement to describe them in E820 and some
platforms require ECAM to work (Bjorn Helgaas)
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more specific (Damien
Le Moal)
- Remove last user and pci_enable_device_io() (Heiner Kallweit)
- Wait for Link Training==0 to avoid possible race (Ilpo Järvinen)
- Skip waiting for devices that have been disconnected while
suspended (Ilpo Järvinen)
- Clear Secondary Status errors after enumeration since Master Aborts
and Unsupported Request errors are an expected part of enumeration
(Vidya Sagar)
MSI:
- Remove unused IMS (Interrupt Message Store) support (Bjorn Helgaas)
Error handling:
- Mask Genesys GL975x SD host controller Replay Timer Timeout
correctable errors caused by a hardware defect; the errors cause
interrupts that prevent system suspend (Kai-Heng Feng)
- Fix EDR-related _DSM support, which previously evaluated revision 5
but assumed revision 6 behavior (Kuppuswamy Sathyanarayanan)
ASPM:
- Simplify link state definitions and mask calculation (Ilpo
Järvinen)
Power management:
- Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports, where BIOS
apparently doesn't know how to put them back in D0 (Mario
Limonciello)
CXL:
- Support resetting CXL devices; special handling required because
CXL Ports mask Secondary Bus Reset by default (Dave Jiang)
DOE:
- Support DOE Discovery Version 2 (Alexey Kardashevskiy)
Endpoint framework:
- Set endpoint BAR to be 64-bit if the driver says that's all the
device supports, in addition to doing so if the size is >2GB
(Niklas Cassel)
- Simplify endpoint BAR allocation and setting interfaces (Niklas
Cassel)
Cadence PCIe controller driver:
- Drop DT binding redundant msi-parent and pci-bus.yaml (Krzysztof
Kozlowski)
Cadence PCIe endpoint driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
Freescale Layerscape PCIe controller driver:
- Convert DT binding to YAML (Frank Li)
MediaTek MT7621 PCIe controller driver:
- Add DT binding missing 'reg' property for child Root Ports
(Krzysztof Kozlowski)
- Fix theoretical string truncation in PHY name (Sergio Paracuellos)
NVIDIA Tegra194 PCIe controller driver:
- Return success for endpoint probe instead of falling through to the
failure path (Vidya Sagar)
Renesas R-Car PCIe controller driver:
- Add DT binding missing IOMMU properties (Geert Uytterhoeven)
- Add DT binding R-Car V4H compatible for host and endpoint mode
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
- Add DT binding missing maxItems to ep-gpios (Krzysztof Kozlowski)
- Set the Subsystem Vendor ID, which was previously zero because it
was masked incorrectly (Rick Wertenbroek)
Synopsys DesignWare PCIe controller driver:
- Restructure DBI register access to accommodate devices where this
requires Refclk to be active (Manivannan Sadhasivam)
- Remove the deinit() callback, which was only need by the
pcie-rcar-gen4, and do it directly in that driver (Manivannan
Sadhasivam)
- Add dw_pcie_ep_cleanup() so drivers that support PERST# can clean
up things like eDMA (Manivannan Sadhasivam)
- Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() to make it parallel
to dw_pcie_ep_init() (Manivannan Sadhasivam)
- Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() to
reflect the actual functionality (Manivannan Sadhasivam)
- Call dw_pcie_ep_init_registers() directly from all the glue
drivers, not just those that require active Refclk from the host
(Manivannan Sadhasivam)
- Remove the "core_init_notifier" flag, which was an obscure way for
glue drivers to indicate that they depend on Refclk from the host
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Add DT binding J784S4 SoC Device ID (Siddharth Vadapalli)
- Add DT binding J722S SoC support (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Add DT binding missing num-viewport, phys and phy-name properties
(Jan Kiszka)
Miscellaneous:
- Constify and annotate with __ro_after_init (Heiner Kallweit)
- Convert DT bindings to YAML (Krzysztof Kozlowski)
- Check for kcalloc() failure in of_pci_prop_intr_map() (Duoming
Zhou)"
* tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits)
PCI: Do not wait for disconnected devices when resuming
x86/pci: Skip early E820 check for ECAM region
PCI: Remove unused pci_enable_device_io()
ata: pata_cs5520: Remove unnecessary call to pci_enable_device_io()
PCI: Update pci_find_capability() stub return types
PCI: Remove PCI_IRQ_LEGACY
scsi: vmw_pvscsi: Do not use PCI_IRQ_LEGACY instead of PCI_IRQ_LEGACY
scsi: pmcraid: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: mpt3sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: megaraid_sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: ipr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: hpsa: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: arcmsr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
wifi: rtw89: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
dt-bindings: PCI: rockchip,rk3399-pcie: Add missing maxItems to ep-gpios
Revert "genirq/msi: Provide constants for PCI/IMS support"
Revert "x86/apic/msi: Enable PCI/IMS"
Revert "iommu/vt-d: Enable PCI/IMS"
Revert "iommu/amd: Enable PCI/IMS"
Revert "PCI/MSI: Provide IMS (Interrupt Message Store) support"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux
Pull kgdb updates from Daniel Thompson:
"Nine patches this cycle and they split into just three topics:
- Adopt coccinelle's recommendation to adopt str_plural()
- A set of seven patches to refactor kdb_read() to improve both code
clarity and its discipline with respect to fixed size buffers.
This isn't just a refactor. Between them these also fix a cursor
movement redraw problem and two buffer overflows (one latent and
one real, albeit difficult to tickle).
- Fix an NMI-safety problem when enqueuing kdb's keyboard reset code
I wrote eight of the nine patches in this collection so many thanks to
Doug Anderson for the reviews. The changes that affects
drivers/tty/serial is acked by Greg KH"
* tag 'kgdb-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
serial: kgdboc: Fix NMI-safety problems from keyboard reset code
kdb: Simplify management of tmpbuffer in kdb_read()
kdb: Replace double memcpy() with memmove() in kdb_read()
kdb: Use format-specifiers rather than memset() for padding in kdb_read()
kdb: Merge identical case statements in kdb_read()
kdb: Fix console handling when editing and tab-completing commands
kdb: Use format-strings rather than '\0' injection in kdb_read()
kdb: Fix buffer overflow during tab-complete
kdb: Use str_plural() to fix Coccinelle warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Use no_printk() instead of "if (0) printk()" constructs to avoid
generating printk index for messages disabled at compile time
- Remove deprecated strncpy/strcpy from printk.c
- Remove redundant CONFIG_BASE_FULL in favor of CONFIG_BASE_SMALL
* tag 'printk-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk: cleanup deprecated uses of strncpy/strcpy
printk: Remove redundant CONFIG_BASE_FULL
printk: Change type of CONFIG_BASE_SMALL to bool
printk: Fix LOG_CPU_MAX_BUF_SHIFT when BASE_SMALL is enabled
ceph: Use no_printk() helper
dyndbg: Use *no_printk() helpers
dev_printk: Add and use dev_no_printk()
printk: Let no_printk() use _printk()
|
|
Make use of iucv_alloc_device() to get rid of quite some code.
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240506194454.1160315-6-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull alpha updates from Arnd Bergmann:
"I had investigated dropping support for alpha EV5 and earlier a while
ago after noticing that this is the only supported CPU family in the
kernel without native byte access and that Debian has already dropped
support for this generation last year [1] in order to improve
performance for the newer machines.
This topic came up again when Paul McKenney noticed that parts of the
RCU code already rely on byte access and do not work on alpha EV5
reliably, so we decided on using my series to avoid the problem
entirely.
Al Viro did another series for alpha to address all the known build
issues. I rebased his patches without any further changes and included
it as a baseline for my work here to avoid conflicts and allow
backporting the fixes to stable kernels for the now removed hardware
support as well"
[ I dearly loved alpha back in the days, but the lack of byte and word
operations was a horrible mistake and made everything worse -
including very much the crazy IO contortions that resulted from it.
It certainly wasn't the only mistake in the architecture, but it's the
first-order issue.
So while it's a bit sad to see the support for my first alpha go away,
if you want to run museum hardware, maybe you should use museum
kernels.. - Linus ]
* tag 'asm-generic-alpha' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
alpha: drop pre-EV56 support
alpha: cabriolet: remove EV5 CPU support
alpha: remove LCA and APECS based machines
alpha: sable: remove early machine support
alpha: remove DECpc AXP150 (Jensen) support
alpha: trim the unused stuff from asm-offsets.c
alpha: jensen, t2 - make __EXTERN_INLINE same as for the rest
alpha: core_lca: take the unused functions out
alpha: missing includes
alpha: sys_sio: fix misspelled ifdefs
alpha: don't make functions public without a reason
alpha: add clone3() support
alpha: fix modversions for strcpy() et.al.
alpha: sort scr_mem{cpy,move}w() out
|
