| Age | Commit message (Collapse) | Author |
|---|
|
Pull MIPS updates from Paul Burton:
- A set of memblock initialization improvements thanks to Serge Semin,
tidying up after our conversion from bootmem to memblock back in
v4.20.
- Our eBPF JIT the previously supported only MIPS64r2 through MIPS64r5
is improved to also support MIPS64r6. Support for MIPS32 systems is
introduced, with the caveat that it only works for programs that
don't use 64 bit registers or operations - those will bail out & need
to be interpreted.
- Improvements to the allocation & configuration of our exception
vector that should fix issues seen on some platforms using recent
versions of U-Boot.
- Some minor improvements to code generated for jump labels, along with
enabling them by default for generic kernels.
* tag 'mips_5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (27 commits)
mips: Manually call fdt_init_reserved_mem() method
mips: Make sure dt memory regions are valid
mips: Perform early low memory test
mips: Dump memblock regions for debugging
mips: Add reserve-nomap memory type support
mips: Use memblock to reserve the __nosave memory range
mips: Discard post-CMA-init foreach loop
mips: Reserve memory for the kernel image resources
MIPS: Remove duplicate EBase configuration
MIPS: Sync icache for whole exception vector
MIPS: Always allocate exception vector for MIPSr2+
MIPS: Use memblock_phys_alloc() for exception vector
mips: Combine memblock init and memory reservation loops
mips: Discard rudiments from bootmem_init
mips: Make sure kernel .bss exists in boot mem pool
mips: vdso: drop unnecessary cc-ldoption
Revert "MIPS: ralink: fix cpu clock of mt7621 and add dt clk devices"
MIPS: generic: Enable CONFIG_JUMP_LABEL
MIPS: jump_label: Use compact branches for >= r6
MIPS: jump_label: Remove redundant nops
...
|
|
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"We've got a reasonably broad set of audit patches for the v5.2 merge
window, the highlights are below:
- The biggest change, and the source of all the arch/* changes, is
the patchset from Dmitry to help enable some of the work he is
doing around PTRACE_GET_SYSCALL_INFO.
To be honest, including this in the audit tree is a bit of a
stretch, but it does help move audit a little further along towards
proper syscall auditing for all arches, and everyone else seemed to
agree that audit was a "good" spot for this to land (or maybe they
just didn't want to merge it? dunno.).
- We can now audit time/NTP adjustments.
- We continue the work to connect associated audit records into a
single event"
* tag 'audit-pr-20190507' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit: (21 commits)
audit: fix a memory leak bug
ntp: Audit NTP parameters adjustment
timekeeping: Audit clock adjustments
audit: purge unnecessary list_empty calls
audit: link integrity evm_write_xattrs record to syscall event
syscall_get_arch: add "struct task_struct *" argument
unicore32: define syscall_get_arch()
Move EM_UNICORE to uapi/linux/elf-em.h
nios2: define syscall_get_arch()
nds32: define syscall_get_arch()
Move EM_NDS32 to uapi/linux/elf-em.h
m68k: define syscall_get_arch()
hexagon: define syscall_get_arch()
Move EM_HEXAGON to uapi/linux/elf-em.h
h8300: define syscall_get_arch()
c6x: define syscall_get_arch()
arc: define syscall_get_arch()
Move EM_ARCOMPACT and EM_ARCV2 to uapi/linux/elf-em.h
audit: Make audit_log_cap and audit_copy_inode static
audit: connect LOGIN record to its syscall record
...
|
|
Pull block updates from Jens Axboe:
"Nothing major in this series, just fixes and improvements all over the
map. This contains:
- Series of fixes for sed-opal (David, Jonas)
- Fixes and performance tweaks for BFQ (via Paolo)
- Set of fixes for bcache (via Coly)
- Set of fixes for md (via Song)
- Enabling multi-page for passthrough requests (Ming)
- Queue release fix series (Ming)
- Device notification improvements (Martin)
- Propagate underlying device rotational status in loop (Holger)
- Removal of mtip32xx trim support, which has been disabled for years
(Christoph)
- Improvement and cleanup of nvme command handling (Christoph)
- Add block SPDX tags (Christoph)
- Cleanup/hardening of bio/bvec iteration (Christoph)
- A few NVMe pull requests (Christoph)
- Removal of CONFIG_LBDAF (Christoph)
- Various little fixes here and there"
* tag 'for-5.2/block-20190507' of git://git.kernel.dk/linux-block: (164 commits)
block: fix mismerge in bvec_advance
block: don't drain in-progress dispatch in blk_cleanup_queue()
blk-mq: move cancel of hctx->run_work into blk_mq_hw_sysfs_release
blk-mq: always free hctx after request queue is freed
blk-mq: split blk_mq_alloc_and_init_hctx into two parts
blk-mq: free hw queue's resource in hctx's release handler
blk-mq: move cancel of requeue_work into blk_mq_release
blk-mq: grab .q_usage_counter when queuing request from plug code path
block: fix function name in comment
nvmet: protect discovery change log event list iteration
nvme: mark nvme_core_init and nvme_core_exit static
nvme: move command size checks to the core
nvme-fabrics: check more command sizes
nvme-pci: check more command sizes
nvme-pci: remove an unneeded variable initialization
nvme-pci: unquiesce admin queue on shutdown
nvme-pci: shutdown on timeout during deletion
nvme-pci: fix psdt field for single segment sgls
nvme-multipath: don't print ANA group state by default
nvme-multipath: split bios with the ns_head bio_set before submitting
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull pidfd updates from Christian Brauner:
"This patchset makes it possible to retrieve pidfds at process creation
time by introducing the new flag CLONE_PIDFD to the clone() system
call. Linus originally suggested to implement this as a new flag to
clone() instead of making it a separate system call.
After a thorough review from Oleg CLONE_PIDFD returns pidfds in the
parent_tidptr argument. This means we can give back the associated pid
and the pidfd at the same time. Access to process metadata information
thus becomes rather trivial.
As has been agreed, CLONE_PIDFD creates file descriptors based on
anonymous inodes similar to the new mount api. They are made
unconditional by this patchset as they are now needed by core kernel
code (vfs, pidfd) even more than they already were before (timerfd,
signalfd, io_uring, epoll etc.). The core patchset is rather small.
The bulky looking changelist is caused by David's very simple changes
to Kconfig to make anon inodes unconditional.
A pidfd comes with additional information in fdinfo if the kernel
supports procfs. The fdinfo file contains the pid of the process in
the callers pid namespace in the same format as the procfs status
file, i.e. "Pid:\t%d".
To remove worries about missing metadata access this patchset comes
with a sample/test program that illustrates how a combination of
CLONE_PIDFD and pidfd_send_signal() can be used to gain race-free
access to process metadata through /proc/<pid>.
Further work based on this patchset has been done by Joel. His work
makes pidfds pollable. It finished too late for this merge window. I
would prefer to have it sitting in linux-next for a while and send it
for inclusion during the 5.3 merge window"
* tag 'pidfd-v5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
samples: show race-free pidfd metadata access
signal: support CLONE_PIDFD with pidfd_send_signal
clone: add CLONE_PIDFD
Make anon_inodes unconditional
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
"Here are the locking changes in this cycle:
- rwsem unification and simpler micro-optimizations to prepare for
more intrusive (and more lucrative) scalability improvements in
v5.3 (Waiman Long)
- Lockdep irq state tracking flag usage cleanups (Frederic
Weisbecker)
- static key improvements (Jakub Kicinski, Peter Zijlstra)
- misc updates, cleanups and smaller fixes"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
locking/lockdep: Remove unnecessary unlikely()
locking/static_key: Don't take sleeping locks in __static_key_slow_dec_deferred()
locking/static_key: Factor out the fast path of static_key_slow_dec()
locking/static_key: Add support for deferred static branches
locking/lockdep: Test all incompatible scenarios at once in check_irq_usage()
locking/lockdep: Avoid bogus Clang warning
locking/lockdep: Generate LOCKF_ bit composites
locking/lockdep: Use expanded masks on find_usage_*() functions
locking/lockdep: Map remaining magic numbers to lock usage mask names
locking/lockdep: Move valid_state() inside CONFIG_TRACE_IRQFLAGS && CONFIG_PROVE_LOCKING
locking/rwsem: Prevent unneeded warning during locking selftest
locking/rwsem: Optimize rwsem structure for uncontended lock acquisition
locking/rwsem: Enable lock event counting
locking/lock_events: Don't show pvqspinlock events on bare metal
locking/lock_events: Make lock_events available for all archs & other locks
locking/qspinlock_stat: Introduce generic lockevent_*() counting APIs
locking/rwsem: Enhance DEBUG_RWSEMS_WARN_ON() macro
locking/rwsem: Add debug check for __down_read*()
locking/rwsem: Micro-optimize rwsem_try_read_lock_unqueued()
locking/rwsem: Move rwsem internal function declarations to rwsem-xadd.h
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull unified TLB flushing from Ingo Molnar:
"This contains the generic mmu_gather feature from Peter Zijlstra,
which is an all-arch unification of TLB flushing APIs, via the
following (broad) steps:
- enhance the <asm-generic/tlb.h> APIs to cover more arch details
- convert most TLB flushing arch implementations to the generic
<asm-generic/tlb.h> APIs.
- remove leftovers of per arch implementations
After this series every single architecture makes use of the unified
TLB flushing APIs"
* 'core-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mm/resource: Use resource_overlaps() to simplify region_intersects()
ia64/tlb: Eradicate tlb_migrate_finish() callback
asm-generic/tlb: Remove tlb_table_flush()
asm-generic/tlb: Remove tlb_flush_mmu_free()
asm-generic/tlb: Remove CONFIG_HAVE_GENERIC_MMU_GATHER
asm-generic/tlb: Remove arch_tlb*_mmu()
s390/tlb: Convert to generic mmu_gather
asm-generic/tlb: Introduce CONFIG_HAVE_MMU_GATHER_NO_GATHER=y
arch/tlb: Clean up simple architectures
um/tlb: Convert to generic mmu_gather
sh/tlb: Convert SH to generic mmu_gather
ia64/tlb: Convert to generic mmu_gather
arm/tlb: Convert to generic mmu_gather
asm-generic/tlb, arch: Invert CONFIG_HAVE_RCU_TABLE_INVALIDATE
asm-generic/tlb, ia64: Conditionally provide tlb_migrate_finish()
asm-generic/tlb: Provide generic tlb_flush() based on flush_tlb_mm()
asm-generic/tlb, arch: Provide generic tlb_flush() based on flush_tlb_range()
asm-generic/tlb, arch: Provide generic VIPT cache flush
asm-generic/tlb, arch: Provide CONFIG_HAVE_MMU_GATHER_PAGE_SIZE
asm-generic/tlb: Provide a comment
|
|
Since memblock-patchset was introduced the reserved-memory nodes are
supported being declared in dt-files. So these nodes are actually parsed
during the arch setup procedure when the early_init_fdt_scan_reserved_mem()
method is called. But due to the arch-specific boot mem_map container
utilization we need to manually call the fdt_init_reserved_mem() method
after all the available and reserved memory has been moved to memblock.
The first function call performed before bootmem_init() by the
early_init_fdt_scan_reserved_mem() routine fails due to the lack of any
memblock memory regions to allocate from at that stage.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Serge Semin <Sergey.Semin@t-platforms.ru>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
There are situations when memory regions coming from dts may be
too big for the platform physical address space. This especially
concerns XPA-capable systems. Bootloader may determine more than 4GB
memory available and pass it to the kernel over dts memory node, while
kernel is built without XPA/64BIT support. In this case the region
may either simply be truncated by add_memory_region() method
or by u64->phys_addr_t type casting. But in worst case the method
can even drop the memory region if it exceeds PHYS_ADDR_MAX size.
So lets make sure the retrieved from dts memory regions are valid,
and if some of them aren't, just manually truncate them with a warning
printed out.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Serge Semin <Sergey.Semin@t-platforms.ru>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
memblock subsystem provides a method to optionally test the passed
memory region in case if it was requested via special kernel boot
argument. Lets add the function at the bottom of the arch_mem_init()
method. Testing at this point in the boot sequence should be safe since all
critical areas are now reserved and a minimum of allocations have been
done.
Reviewed-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Serge Semin <Sergey.Semin@t-platforms.ru>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
It is useful to have the whole memblock memory space printed to console
when basic memlock initializations are done. It can be performed by
ready-to-use method memblock_dump_all(), which prints the available
and reserved memory spaces if memblock=debug kernel parameter is
specified. Lets call it at the very end of arch_mem_init() function,
when all memblock memory and reserved regions are defined, but before
any serious allocation is performed.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Serge Semin <Sergey.Semin@t-platforms.ru>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
Three trivial overlapping conflicts.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It might be necessary to prevent the virtual mapping creation for a
requested memory region. For instance there is a "no-map" property
indicating exactly this feature. In this case we need to not only
reserve the specified region by pretending it doesn't exist in the
memory space, but completely remove the range from system just by
removing it from memblock. The same way it's done in default
early_init_dt_reserve_memory_arch() method.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
Originally before legacy bootmem was removed, the memory for the range was
correctly reserved by reserve_bootmem_region(). But since memblock has been
selected for early memory allocation the function can be utilized only
after paging is fully initialized (as it is done by memblock_free_all()
function). So calling it from arch_mem_init() method is prone to errors,
and at this stage we need to reserve the memory in the memblock allocator.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
Really the loop is pointless, since it walks over memblock-reserved
memory regions and mark them as reserved in memblock. Before
bootmem was removed from the kernel, this loop had been
used to map the memory reserved by CMA into the legacy bootmem
allocator. But now the early memory allocator is memblock,
which is used by CMA for reservation, so we don't need any mapping
anymore.
Reviewed-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
The reserved_end variable had been used by the bootmem_init() code
to find a lowest limit of memory available for memmap blob. The original
code just tried to find a free memory space higher than kernel was placed.
This limitation seems justified for the memmap ragion search process, but
I can't see any obvious reason to reserve the unused space below kernel
seeing some platforms place it much higher than standard 1MB. Moreover
the RELOCATION config enables it to be loaded at any memory address.
So lets reserve the memory occupied by the kernel only, leaving the region
below being free for allocations. After doing this we can now discard the
code freeing a space between kernel _text and VMLINUX_LOAD_ADDRESS symbols
since it's going to be free anyway (unless marked as reserved by
platforms).
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
Clean up our configuration of the EBase register by making
configure_exception_vector() write to it unconditionally on systems
implementing MIPSr2 or higher, and removing the duplicate code in
per_cpu_trap_init(). The latter would have duplicated work on systems
with vectored interrupts, and didn't set BEV for safety like the
configure_exception_vector() version of the code does.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Cc: linux-mips@vger.kernel.org
|
|
Rather than performing cache flushing for a fixed 0x400 bytes, use the
actual size of the vector in order to ensure we cover all emitted code
on systems that make use of vectored interrupts.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Cc: linux-mips@vger.kernel.org
|
|
Currently we allocate the exception vector on systems which use a
vectored interrupt mode, but otherwise attempt to reuse whatever
exception vector the bootloader uses.
This can be problematic for a number of reasons:
1) The memory isn't properly marked reserved in the memblock
allocator. We've relied on the fact that EBase is generally in the
memory below the kernel image which we don't free, but this is
about to change.
2) Recent versions of U-Boot place their exception vector high in
kseg0, in memory which isn't protected by being lower than the
kernel anyway & can end up being clobbered.
3) We are unnecessarily reliant upon there being memory at the address
EBase points to upon entry to the kernel. This is often the case,
but if the bootloader doesn't configure EBase & leaves it with its
default value then we rely upon there being memory at physical
address 0 for no good reason.
Improve this situation by allocating the exception vector in all cases
when running on MIPSr2 or higher, and reserving the memory for MIPSr1 or
lower. This ensures we don't clobber the exception vector in any
configuration, and for MIPSr2 & higher removes the need for memory at
physical address 0.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Cc: linux-mips@vger.kernel.org
|
|
Allocate the exception vector using memblock_phys_alloc() which gives us
a physical address, rather than the previous convoluted setup which
obtained a virtual address using memblock_alloc(), converted it to a
physical address & then back to a virtual address.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Cc: linux-mips@vger.kernel.org
|
|
Alexei Starovoitov says:
====================
pull-request: bpf 2019-04-25
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) the bpf verifier fix to properly mark registers in all stack frames, from Paul.
2) preempt_enable_no_resched->preempt_enable fix, from Peter.
3) other misc fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two easy cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix sparse warning:
arch/mips/net/ebpf_jit.c:196:5: warning:
symbol 'ebpf_to_mips_reg' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Before bootmem was completely removed from the kernel, the last loop
in the bootmem_init() had been used to reserve the correspondingly
marked regions, initialize sparsemem sections and to free the low memory
pages, which then would be used for early memory allocations. After the
bootmem removing patchset had been merged the loop was left to do the first
two things only. But it didn't do them quite well.
First of all it leaves the BOOT_MEM_INIT_RAM memory types unreserved,
which is definitely bug (although it isn't noticeable due to being used
by the kernel region only, which is fully marked as reserved). Secondly
the reservation is supposed to be done for any memory including the
high one. (I couldn't figure out why the highmem was ignored in the first
place, since platforms and dts' may declare any memory region for
reservation) Thirdly the reserved_end variable had been used here to not
accidentally free memory occupied by kernel. Since we already reserved the
corresponding region higher in this method there is no need in using the
variable here anymore. Fourthly the sparsemem should be aware of all the
memory types in the system including the ROM_DATA even if it is going to
be reserved for the whole system uptime. Finally after all these notes are
fixed the loop of memory reservation can be freely merged into the memory
installation loop as it's done in this patch.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
There is a pointless code left in the bootmem_init() method since
the bootmem allocator removal. First part resides the PFN ranges
calculation loop. The conditional expressions and continue operator
are useless there, since nothing is done after them. Second part is
in RAM ranges installation loop. We can simplify the conditions cascade
a bit without much of the logic redefinition, so to reduce the code
length. In particular the end boundary value can be verified after
the possible reduction to be below max_low_pfn.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
Current MIPS platform code makes sure the kernel text, data and init
sections are added to the boot memory map pool right after the
arch-specific memory setup method has been executed. But for some reason
the MIPS platform code skipped the kernel .bss section, which definitely
should be in the boot mem pool as well in any case. Lets fix this just be
adding the space between __bss_start and __bss_stop.
Reviewed-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
Towards the goal of removing cc-ldoption, it seems that --hash-style=
was added to binutils 2.17.50.0.2 in 2006. The minimal required version
of binutils for the kernel according to
Documentation/process/changes.rst is 2.20.
--build-id was added in 2.18 according to binutils-gdb/ld/NEWS.
Link: https://gcc.gnu.org/ml/gcc/2007-01/msg01141.html
Cc: clang-built-linux@googlegroups.com
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Hassan Naveed <hnaveed@wavecomp.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull syscall numbering updates from Arnd Bergmann:
"arch: add pidfd and io_uring syscalls everywhere
This comes a bit late, but should be in 5.1 anyway: we want the newly
added system calls to be synchronized across all architectures in the
release.
I hope that in the future, any newly added system calls can be added
to all architectures at the same time, and tested there while they are
in linux-next, avoiding dependencies between the architecture
maintainer trees and the tree that contains the new system call"
* tag 'syscalls-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
arch: add pidfd and io_uring syscalls everywhere
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A couple more MIPS fixes:
- Fix indirect syscall tracing & seccomp filtering for big endian
MIPS64 kernels, which previously loaded the syscall number
incorrectly & would always use zero.
- Fix performance counter IRQ setup for Atheros/ath79 SoCs, allowing
perf to function on those systems.
And not really a fix, but a useful addition:
- Add a Broadcom mailing list to the MAINTAINERS entry for BMIPS
systems to allow relevant engineers to track patch submissions"
* tag 'mips_fixes_5.1_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: perf: ath79: Fix perfcount IRQ assignment
MIPS: scall64-o32: Fix indirect syscall number load
MAINTAINERS: BMIPS: Add internal Broadcom mailing list
|
|
Pull in v5.1-rc6 to resolve two conflicts. One is in BFQ, in just a
comment, and is trivial. The other one is a conflict due to a later fix
in the bio multi-page work, and needs a bit more care.
* tag 'v5.1-rc6': (770 commits)
Linux 5.1-rc6
block: make sure that bvec length can't be overflow
block: kill all_q_node in request_queue
x86/cpu/intel: Lower the "ENERGY_PERF_BIAS: Set to normal" message's log priority
coredump: fix race condition between mmget_not_zero()/get_task_mm() and core dumping
mm/kmemleak.c: fix unused-function warning
init: initialize jump labels before command line option parsing
kernel/watchdog_hld.c: hard lockup message should end with a newline
kcov: improve CONFIG_ARCH_HAS_KCOV help text
mm: fix inactive list balancing between NUMA nodes and cgroups
mm/hotplug: treat CMA pages as unmovable
proc: fixup proc-pid-vm test
proc: fix map_files test on F29
mm/vmstat.c: fix /proc/vmstat format for CONFIG_DEBUG_TLBFLUSH=y CONFIG_SMP=n
mm/memory_hotplug: do not unlock after failing to take the device_hotplug_lock
mm: swapoff: shmem_unuse() stop eviction without igrab()
mm: swapoff: take notice of completion sooner
mm: swapoff: remove too limiting SWAP_UNUSE_MAX_TRIES
mm: swapoff: shmem_find_swap_entries() filter out other types
slab: store tagged freelist for off-slab slabmgmt
...
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The 'timeval' and 'timespec' data structures used for socket timestamps
are going to be redefined in user space based on 64-bit time_t in future
versions of the C library to deal with the y2038 overflow problem,
which breaks the ABI definition.
Unlike many modern ioctl commands, SIOCGSTAMP and SIOCGSTAMPNS do not
use the _IOR() macro to encode the size of the transferred data, so it
remains ambiguous whether the application uses the old or new layout.
The best workaround I could find is rather ugly: we redefine the command
code based on the size of the respective data structure with a ternary
operator. This lets it get evaluated as late as possible, hopefully after
that structure is visible to the caller. We cannot use an #ifdef here,
because inux/sockios.h might have been included before any libc header
that could determine the size of time_t.
The ioctl implementation now interprets the new command codes as always
referring to the 64-bit structure on all architectures, while the old
architecture specific command code still refers to the old architecture
specific layout. The new command number is only used when they are
actually different.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the anon_inodes facility unconditional so that it can be used by core
VFS code and pidfd code.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[christian@brauner.io: adapt commit message to mention pidfds]
Signed-off-by: Christian Brauner <christian@brauner.io>
|
|
Currently it's not possible to use perf on ath79 due to genirq flags
mismatch happening on static virtual IRQ 13 which is used for
performance counters hardware IRQ 5.
On TP-Link Archer C7v5:
CPU0
2: 0 MIPS 2 ath9k
4: 318 MIPS 4 19000000.eth
7: 55034 MIPS 7 timer
8: 1236 MISC 3 ttyS0
12: 0 INTC 1 ehci_hcd:usb1
13: 0 gpio-ath79 2 keys
14: 0 gpio-ath79 5 keys
15: 31 AR724X PCI 1 ath10k_pci
$ perf top
genirq: Flags mismatch irq 13. 00014c83 (mips_perf_pmu) vs. 00002003 (keys)
On TP-Link Archer C7v4:
CPU0
4: 0 MIPS 4 19000000.eth
5: 7135 MIPS 5 1a000000.eth
7: 98379 MIPS 7 timer
8: 30 MISC 3 ttyS0
12: 90028 INTC 0 ath9k
13: 5520 INTC 1 ehci_hcd:usb1
14: 4623 INTC 2 ehci_hcd:usb2
15: 32844 AR724X PCI 1 ath10k_pci
16: 0 gpio-ath79 16 keys
23: 0 gpio-ath79 23 keys
$ perf top
genirq: Flags mismatch irq 13. 00014c80 (mips_perf_pmu) vs. 00000080 (ehci_hcd:usb1)
This problem is happening, because currently statically assigned virtual
IRQ 13 for performance counters is not claimed during the initialization
of MIPS PMU during the bootup, so the IRQ subsystem doesn't know, that
this interrupt isn't available for further use.
So this patch fixes the issue by simply booking hardware IRQ 5 for MIPS PMU.
Tested-by: Kevin 'ldir' Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
|
|
Commit 4c21b8fd8f14 (MIPS: seccomp: Handle indirect system calls (o32))
added indirect syscall detection for O32 processes running on MIPS64,
but it did not work correctly for big endian kernel/processes. The
reason is that the syscall number is loaded from ARG1 using the lw
instruction while this is a 64-bit value, so zero is loaded instead of
the syscall number.
Fix the code by using the ld instruction instead. When running a 32-bit
processes on a 64 bit CPU, the values are properly sign-extended, so it
ensures the value passed to syscall_trace_enter is correct.
Recent systemd versions with seccomp enabled whitelist the getpid
syscall for their internal processes (e.g. systemd-journald), but call
it through syscall(SYS_getpid). This fix therefore allows O32 big endian
systems with a 64-bit kernel to run recent systemd versions.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: <stable@vger.kernel.org> # v3.15+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
Add the io_uring and pidfd_send_signal system calls to all architectures.
These system calls are designed to handle both native and compat tasks,
so all entries are the same across architectures, only arm-compat and
the generic tale still use an old format.
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> (s390)
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit e6046b5e69a0 ("MIPS: ralink: fix cpu clock of mt7621 and add dt
clk devices") includes a file that doesn't exist, causing build
failures... Revert it.
References: https://lore.kernel.org/linux-mips/CAJsYDVJvviz8a2oVmb0XL3OB+=Eecu-3kC9T9vsmxpuC_BqDSA@mail.gmail.com/
Signed-off-by: Paul Burton <paul.burton@mips.com>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A few minor MIPS fixes:
- Provide struct pt_regs * from get_irq_regs() to kgdb_nmicallback()
when handling an IPI triggered by kgdb_roundup_cpus(), matching the
behavior of other architectures & resolving kgdb issues for SMP
systems.
- Defer a pointer dereference until after a NULL check in the
irq_shutdown callback for SGI IP27 HUB interrupts.
- A defconfig update for the MSCC Ocelot to enable some necessary
drivers"
* tag 'mips_fixes_5.1_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: generic: Add switchdev, pinctrl and fit to ocelot_defconfig
MIPS: SGI-IP27: Fix use of unchecked pointer in shutdown_bridge_irq
MIPS: KGDB: fix kgdb support for SMP platforms.
|
|
Enable CONFIG_JUMP_LABEL for generic configs in order to better optimize
at runtime and get better test coverage for our jump label support.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
|
|
MIPSr6 introduced compact branches which have no delay slots. Make use
of them for jump labels in order to avoid the need for a nop to fill the
branch or jump delay slot, saving 4 bytes of code for each static branch.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
|
|
Both arch_static_branch() & arch_static_branch_jump() emit a control
transfer instruction (ie. branch or jump) without disabling assembler
re-ordering. As such the assembler will automatically fill their delay
slots.
Both functions follow their branch or jump with an explicit nop that at
first appears to be there to fill the delay slot, but given that the
assembler will do that the explicit nops serve no purpose & we end up
with our branch or jump followed by 2 nops. Remove the redundant nops.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
|
|
A small batch of MIPS fixes for 5.1:
- An interrupt masking fix for Loongson-based Lemote 2F systems (fixing
a regression from v3.19).
- A relocation fix for configurations in which the devicetree is stored
in an ELF section (fixing a regression from v4.7).
- Fix jump labels for MIPSr6 kernels where they previously could
inadvertently place a control transfer instruction in a forbidden slot
& take unexpected exceptions (fixing MIPSr6 support added in v4.0).
- Extend an existing USB power workaround for the Netgear WNDR3400 to v2
boards in addition to the v3 ones that already used it.
- Remove the custom MIPS32 definition of __kernel_fsid_t to make it
consistent with MIPS64 & every other architecture, in particular
resolving issues for code which tries to print the val field whose
type previously differed (though had identical memory layout).
Merged into mips-next to gain the MIPSr6 jump label fix before enabling
jump labels by default for generic kernel builds.
Signed-off-by: Paul Burton <paul.burton@mips.com>
|
|
The mmiowb() macro is horribly difficult to use and drivers will continue
to work most of the time if they omit a call when it is required.
Rather than rely on driver authors getting this right, push mmiowb() into
arch_spin_unlock() for mips. If this is deemed to be a performance issue,
a subsequent optimisation could make use of ARCH_HAS_MMIOWB to elide
the barrier in cases where no I/O writes were performed inside the
critical section.
Acked-by: Paul Burton <paul.burton@mips.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Hook up asm-generic/mmiowb.h to Kbuild for all architectures so that we
can subsequently include asm/mmiowb.h from core code.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Currently support for 64-bit sector_t and blkcnt_t is optional on 32-bit
architectures. These types are required to support block device and/or
file sizes larger than 2 TiB, and have generally defaulted to on for
a long time. Enabling the option only increases the i386 tinyconfig
size by 145 bytes, and many data structures already always use
64-bit values for their in-core and on-disk data structures anyway,
so there should not be a large change in dynamic memory usage either.
Dropping this option removes a somewhat weird non-default config that
has cause various bugs or compiler warnings when actually used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
At Linux Plumbers, Andy Lutomirski approached me and pointed out that the
function call syscall_get_arguments() implemented in x86 was horribly
written and not optimized for the standard case of passing in 0 and 6 for
the starting index and the number of system calls to get. When looking at
all the users of this function, I discovered that all instances pass in only
0 and 6 for these arguments. Instead of having this function handle
different cases that are never used, simply rewrite it to return the first 6
arguments of a system call.
This should help out the performance of tracing system calls by ptrace,
ftrace and perf.
Link: http://lkml.kernel.org/r/20161107213233.754809394@goodmis.org
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Dave Martin <dave.martin@arm.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: x86@kernel.org
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-c6x-dev@linux-c6x.org
Cc: uclinux-h8-devel@lists.sourceforge.jp
Cc: linux-hexagon@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: nios2-dev@lists.rocketboards.org
Cc: openrisc@lists.librecores.org
Cc: linux-parisc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-s390@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Cc: linux-um@lists.infradead.org
Cc: linux-xtensa@linux-xtensa.org
Cc: linux-arch@vger.kernel.org
Acked-by: Paul Burton <paul.burton@mips.com> # MIPS parts
Acked-by: Max Filippov <jcmvbkbc@gmail.com> # For xtensa changes
Acked-by: Will Deacon <will.deacon@arm.com> # For the arm64 bits
Reviewed-by: Thomas Gleixner <tglx@linutronix.de> # for x86
Reviewed-by: Dmitry V. Levin <ldv@altlinux.org>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
For a long time the mt7621 uses a fixed cpu clock which causes a problem
if the cpu frequency is not 880MHz.
This patch fixes the cpu clock calculation and adds the cpu/bus clkdev
which will be used in dts.
Ported from OpenWrt:
c7ca224299 ramips: fix cpu clock of mt7621 and add dt clk devices
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: John Crispin <john@phrozen.org>
Cc: linux-kernel@vger.kernel.org
|
|
Some of the configuration were not selected by default anymore, therefore
enable them again. Also remove some configs which are used for MSCC Ocelot.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: <alexandre.belloni@bootlin.com>
Cc: <UNGLinuxDriver@microchip.com>
Cc: <ralf@linux-mips.org>
Cc: <jhogan@kernel.org>
Cc: <linux-mips@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
|
|
Currently, we have two different implementation of rwsem:
1) CONFIG_RWSEM_GENERIC_SPINLOCK (rwsem-spinlock.c)
2) CONFIG_RWSEM_XCHGADD_ALGORITHM (rwsem-xadd.c)
As we are going to use a single generic implementation for rwsem-xadd.c
and no architecture-specific code will be needed, there is no point
in keeping two different implementations of rwsem. In most cases, the
performance of rwsem-spinlock.c will be worse. It also doesn't get all
the performance tuning and optimizations that had been implemented in
rwsem-xadd.c over the years.
For simplication, we are going to remove rwsem-spinlock.c and make all
architectures use a single implementation of rwsem - rwsem-xadd.c.
All references to RWSEM_GENERIC_SPINLOCK and RWSEM_XCHGADD_ALGORITHM
in the code are removed.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-c6x-dev@linux-c6x.org
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-um@lists.infradead.org
Cc: linux-xtensa@linux-xtensa.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: nios2-dev@lists.rocketboards.org
Cc: openrisc@lists.librecores.org
Cc: uclinux-h8-devel@lists.sourceforge.jp
Link: https://lkml.kernel.org/r/20190322143008.21313-3-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
