| Age | Commit message (Collapse) | Author |
|---|
|
commit 6abe0300a1d5242f4ff89257197f284679af1a06 upstream.
Reading a channel through sysfs, or starting a buffered capture, can
occasionally turn off the touchscreen.
This is because the read_raw() and buffer preenable()/postdisable()
callbacks unschedule current conversions on all channels. If a delay
channel happens to schedule a touchscreen conversion at the same time,
the conversion gets cancelled and the touchscreen sequence stops.
This is probably related to this note from the reference manual:
"If a delay group schedules channels to be sampled and a manual
write to the schedule field in CTRL0 occurs while the block is
discarding samples, the LRADC will switch to the new schedule
and will not sample the channels that were previously scheduled.
The time window for this to happen is very small and lasts only
while the LRADC is discarding samples."
So make the callbacks only unschedule conversions for the channels they
use. This means channel 0 for read_raw() and channels 0-5 for the buffer
(if the touchscreen is enabled). Since the touchscreen uses different
channels (6 and 7), it no longer gets turned off.
This is tested and fixes the issue on i.MX28, but hasn't been tested on
i.MX23.
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 86bf7f3ef7e961e91e16dceb31ae0f583483b204 upstream.
Reading a channel through sysfs, or starting a buffered capture, will
currently turn off the touchscreen. This is because the read_raw() and
buffer preenable()/postdisable() callbacks disable interrupts for all
LRADC channels, including those the touchscreen uses.
So make the callbacks only disable interrupts for the channels they use.
This means channel 0 for read_raw() and channels 0-5 for the buffer (if
the touchscreen is enabled). Since the touchscreen uses different
channels (6 and 7), it no longer gets turned off.
Note that only i.MX28 is affected by this issue, i.MX23 should be fine.
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f81197b8a31b8fb287ae57f597b5b6841e1ece92 upstream.
The touchscreen was initially designed [1] to map all of its physical
channels to one virtual channel, leaving buffered capture to use the
remaining 7 virtual channels. When the touchscreen was reimplemented
[2], it was made to use four virtual channels, which overlap and
conflict with the channels the buffer uses.
As a result, when the buffer is enabled, the touchscreen's virtual
channels are remapped to whichever physical channels the buffer was
configured with, causing the touchscreen to read those instead of the
touch measurement channels. Effectively the touchscreen stops working.
So here we separate the channels again, giving the touchscreen 2 virtual
channels and the buffer 6. We can't give the touchscreen just 1 channel
as before, as the current pressure calculation requires 2 channels to be
read at the same time.
This makes the touchscreen continue to work during buffered capture. It
has been tested on i.MX28, but not on i.MX23.
[1] 06ddd353f5c8 ("iio: mxs: Implement support for touchscreen")
[2] dee05308f602 ("Staging/iio/adc/touchscreen/MXS: add interrupt driven
touch detection")
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 19e353f2b344ad86cea6ebbc0002e5f903480a90 upstream.
The intention is obviously to sign-extend a 12 bit quantity. But
because of C's promotion rules, the assignment is equivalent to "val16
&= 0xfff;". Use the proper API for this.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03305e535cd5cdc1079b32909bf4b2dd67d46f7f upstream.
Since commit c8231a9af8147f8a ("iio: mxs-lradc: compute temperature
from channel 8 and 9") with the removal of adc channel 9 there is
no 1-1 mapping in the channel spec.
All hwmon channel values above 9 are accessible via there index minus
one. So add a hidden iio channel 9 to fix this issue.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 956421fbb74c3a6261903f3836c0740187cf038b upstream.
'ret_from_fork' checks TIF_IA32 to determine whether 'pt_regs' and
the related state make sense for 'ret_from_sys_call'. This is
entirely the wrong check. TS_COMPAT would make a little more
sense, but there's really no point in keeping this optimization
at all.
This fixes a return to the wrong user CS if we came from int
0x80 in a 64-bit task.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/4710be56d76ef994ddf59087aad98c000fbab9a4.1424989793.git.luto@amacapital.net
[ Backported from tip:x86/asm. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa179935edea9a64dec4b757090c8106a3907ffa upstream.
This patch adds a check to sbc_parse_cdb() in order to detect when
an LBA + sector vs. end-of-device calculation wraps when the LBA is
sufficently large enough (eg: 0xFFFFFFFFFFFFFFFF).
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8e575c50a171f2579e367a7f778f86477dfdaf49 upstream.
This patch adds a check to sbc_setup_write_same() to verify
the incoming WRITE_SAME LBA + number of blocks does not exceed
past the end-of-device.
Also check for potential LBA wrap-around as well.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f161d4b44d7cc1dc66b53365215227db356378b1 upstream.
This patch addresses the original PR_APTPL_BUF_LEN = 8k limitiation
for write-out of PR APTPL metadata that Martin has recently been
running into.
It changes core_scsi3_update_and_write_aptpl() to use vzalloc'ed
memory instead of kzalloc, and increases the default hardcoded
length to 256k.
It also adds logic in core_scsi3_update_and_write_aptpl() to double
the original length upon core_scsi3_update_aptpl_buf() failure, and
retries until the vzalloc'ed buffer is large enough to accommodate
the outgoing APTPL metadata.
Reported-by: Martin Svec <martin.svec@zoner.cz>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 09b6e85fc868568e1b2820235a2a851aecbccfcc upstream.
Missing parameter when fetching the real voltage values
from atom. Fixes problems with dynamic clocking on
certain boards.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=87457
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a9c73a0e022c33954835e66fec3cd744af90ec98 upstream.
Emit the EOP twice to avoid cache flushing problems.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 410af8d7285a0b96314845c75c39fd612b755688 upstream.
Enable at init and disable on fini. Workaround for hardware problems.
v2 (chk): extend commit message
v3: add new function
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com> (v2)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9cb12d7b4ccaa976f97ce0c5fd0f1b6a83bc2a75 upstream.
For whatever reason, generic_access_phys() only remaps one page, but
actually allows to access arbitrary size. It's quite easy to trigger
large reads, like printing out large structure with gdb, which leads to a
crash. Fix it by remapping correct size.
Fixes: 28b2ee20c7cb ("access_process_vm device memory infrastructure")
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 372549c2a3778fd3df445819811c944ad54609ca upstream.
What we want to check here is whether there is highorder freepage in buddy
list of other migratetype in order to steal it without fragmentation.
But, current code just checks cc->order which means allocation request
order. So, this is wrong.
Without this fix, non-movable synchronous compaction below pageblock order
would not stopped until compaction is complete, because migratetype of
most pageblocks are movable and high order freepage made by compaction is
usually on movable type buddy list.
There is some report related to this bug. See below link.
http://www.spinics.net/lists/linux-mm/msg81666.html
Although the issued system still has load spike comes from compaction,
this makes that system completely stable and responsive according to his
report.
stress-highalloc test in mmtests with non movable order 7 allocation
doesn't show any notable difference in allocation success rate, but, it
shows more compaction success rate.
Compaction success rate (Compaction success * 100 / Compaction stalls, %)
18.47 : 28.94
Fixes: 1fb3f8ca0e92 ("mm: compaction: capture a suitable high-order page immediately when it is made available")
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8138a67a5557ffea3a21dfd6f037842d4e748513 upstream.
I noticed that "allowed" can easily overflow by falling below 0, because
(total_vm / 32) can be larger than "allowed". The problem occurs in
OVERCOMMIT_NONE mode.
In this case, a huge allocation can success and overcommit the system
(despite OVERCOMMIT_NONE mode). All subsequent allocations will fall
(system-wide), so system become unusable.
The problem was masked out by commit c9b1d0981fcc
("mm: limit growth of 3% hardcoded other user reserve"),
but it's easy to reproduce it on older kernels:
1) set overcommit_memory sysctl to 2
2) mmap() large file multiple times (with VM_SHARED flag)
3) try to malloc() large amount of memory
It also can be reproduced on newer kernels, but miss-configured
sysctl_user_reserve_kbytes is required.
Fix this issue by switching to signed arithmetic here.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Cc: Andrew Shewmaker <agshew@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5703b087dc8eaf47bfb399d6cf512d471beff405 upstream.
I noticed, that "allowed" can easily overflow by falling below 0,
because (total_vm / 32) can be larger than "allowed". The problem
occurs in OVERCOMMIT_NONE mode.
In this case, a huge allocation can success and overcommit the system
(despite OVERCOMMIT_NONE mode). All subsequent allocations will fall
(system-wide), so system become unusable.
The problem was masked out by commit c9b1d0981fcc
("mm: limit growth of 3% hardcoded other user reserve"),
but it's easy to reproduce it on older kernels:
1) set overcommit_memory sysctl to 2
2) mmap() large file multiple times (with VM_SHARED flag)
3) try to malloc() large amount of memory
It also can be reproduced on newer kernels, but miss-configured
sysctl_user_reserve_kbytes is required.
Fix this issue by switching to signed arithmetic here.
[akpm@linux-foundation.org: use min_t]
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Cc: Andrew Shewmaker <agshew@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 99592d598eca62bdbbf62b59941c189176dfc614 upstream.
When studying page stealing, I noticed some weird looking decisions in
try_to_steal_freepages(). The first I assume is a bug (Patch 1), the
following two patches were driven by evaluation.
Testing was done with stress-highalloc of mmtests, using the
mm_page_alloc_extfrag tracepoint and postprocessing to get counts of how
often page stealing occurs for individual migratetypes, and what
migratetypes are used for fallbacks. Arguably, the worst case of page
stealing is when UNMOVABLE allocation steals from MOVABLE pageblock.
RECLAIMABLE allocation stealing from MOVABLE allocation is also not ideal,
so the goal is to minimize these two cases.
The evaluation of v2 wasn't always clear win and Joonsoo questioned the
results. Here I used different baseline which includes RFC compaction
improvements from [1]. I found that the compaction improvements reduce
variability of stress-highalloc, so there's less noise in the data.
First, let's look at stress-highalloc configured to do sync compaction,
and how these patches reduce page stealing events during the test. First
column is after fresh reboot, other two are reiterations of test without
reboot. That was all accumulater over 5 re-iterations (so the benchmark
was run 5x3 times with 5 fresh restarts).
Baseline:
3.19-rc4 3.19-rc4 3.19-rc4
5-nothp-1 5-nothp-2 5-nothp-3
Page alloc extfrag event 10264225 8702233 10244125
Extfrag fragmenting 10263271 8701552 10243473
Extfrag fragmenting for unmovable 13595 17616 15960
Extfrag fragmenting unmovable placed with movable 7989 12193 8447
Extfrag fragmenting for reclaimable 658 1840 1817
Extfrag fragmenting reclaimable placed with movable 558 1677 1679
Extfrag fragmenting for movable 10249018 8682096 10225696
With Patch 1:
3.19-rc4 3.19-rc4 3.19-rc4
6-nothp-1 6-nothp-2 6-nothp-3
Page alloc extfrag event 11834954 9877523 9774860
Extfrag fragmenting 11833993 9876880 9774245
Extfrag fragmenting for unmovable 7342 16129 11712
Extfrag fragmenting unmovable placed with movable 4191 10547 6270
Extfrag fragmenting for reclaimable 373 1130 923
Extfrag fragmenting reclaimable placed with movable 302 906 738
Extfrag fragmenting for movable 11826278 9859621 9761610
With Patch 2:
3.19-rc4 3.19-rc4 3.19-rc4
7-nothp-1 7-nothp-2 7-nothp-3
Page alloc extfrag event 4725990 3668793 3807436
Extfrag fragmenting 4725104 3668252 3806898
Extfrag fragmenting for unmovable 6678 7974 7281
Extfrag fragmenting unmovable placed with movable 2051 3829 4017
Extfrag fragmenting for reclaimable 429 1208 1278
Extfrag fragmenting reclaimable placed with movable 369 976 1034
Extfrag fragmenting for movable 4717997 3659070 3798339
With Patch 3:
3.19-rc4 3.19-rc4 3.19-rc4
8-nothp-1 8-nothp-2 8-nothp-3
Page alloc extfrag event 5016183 4700142 3850633
Extfrag fragmenting 5015325 4699613 3850072
Extfrag fragmenting for unmovable 1312 3154 3088
Extfrag fragmenting unmovable placed with movable 1115 2777 2714
Extfrag fragmenting for reclaimable 437 1193 1097
Extfrag fragmenting reclaimable placed with movable 330 969 879
Extfrag fragmenting for movable 5013576 4695266 3845887
In v2 we've seen apparent regression with Patch 1 for unmovable events,
this is now gone, suggesting it was indeed noise. Here, each patch
improves the situation for unmovable events. Reclaimable is improved by
patch 1 and then either the same modulo noise, or perhaps sligtly worse -
a small price for unmovable improvements, IMHO. The number of movable
allocations falling back to other migratetypes is most noisy, but it's
reduced to half at Patch 2 nevertheless. These are least critical as
compaction can move them around.
If we look at success rates, the patches don't affect them, that didn't change.
Baseline:
3.19-rc4 3.19-rc4 3.19-rc4
5-nothp-1 5-nothp-2 5-nothp-3
Success 1 Min 49.00 ( 0.00%) 42.00 ( 14.29%) 41.00 ( 16.33%)
Success 1 Mean 51.00 ( 0.00%) 45.00 ( 11.76%) 42.60 ( 16.47%)
Success 1 Max 55.00 ( 0.00%) 51.00 ( 7.27%) 46.00 ( 16.36%)
Success 2 Min 53.00 ( 0.00%) 47.00 ( 11.32%) 44.00 ( 16.98%)
Success 2 Mean 59.60 ( 0.00%) 50.80 ( 14.77%) 48.20 ( 19.13%)
Success 2 Max 64.00 ( 0.00%) 56.00 ( 12.50%) 52.00 ( 18.75%)
Success 3 Min 84.00 ( 0.00%) 82.00 ( 2.38%) 78.00 ( 7.14%)
Success 3 Mean 85.60 ( 0.00%) 82.80 ( 3.27%) 79.40 ( 7.24%)
Success 3 Max 86.00 ( 0.00%) 83.00 ( 3.49%) 80.00 ( 6.98%)
Patch 1:
3.19-rc4 3.19-rc4 3.19-rc4
6-nothp-1 6-nothp-2 6-nothp-3
Success 1 Min 49.00 ( 0.00%) 44.00 ( 10.20%) 44.00 ( 10.20%)
Success 1 Mean 51.80 ( 0.00%) 46.00 ( 11.20%) 45.80 ( 11.58%)
Success 1 Max 54.00 ( 0.00%) 49.00 ( 9.26%) 49.00 ( 9.26%)
Success 2 Min 58.00 ( 0.00%) 49.00 ( 15.52%) 48.00 ( 17.24%)
Success 2 Mean 60.40 ( 0.00%) 51.80 ( 14.24%) 50.80 ( 15.89%)
Success 2 Max 63.00 ( 0.00%) 54.00 ( 14.29%) 55.00 ( 12.70%)
Success 3 Min 84.00 ( 0.00%) 81.00 ( 3.57%) 79.00 ( 5.95%)
Success 3 Mean 85.00 ( 0.00%) 81.60 ( 4.00%) 79.80 ( 6.12%)
Success 3 Max 86.00 ( 0.00%) 82.00 ( 4.65%) 82.00 ( 4.65%)
Patch 2:
3.19-rc4 3.19-rc4 3.19-rc4
7-nothp-1 7-nothp-2 7-nothp-3
Success 1 Min 50.00 ( 0.00%) 44.00 ( 12.00%) 39.00 ( 22.00%)
Success 1 Mean 52.80 ( 0.00%) 45.60 ( 13.64%) 42.40 ( 19.70%)
Success 1 Max 55.00 ( 0.00%) 46.00 ( 16.36%) 47.00 ( 14.55%)
Success 2 Min 52.00 ( 0.00%) 48.00 ( 7.69%) 45.00 ( 13.46%)
Success 2 Mean 53.40 ( 0.00%) 49.80 ( 6.74%) 48.80 ( 8.61%)
Success 2 Max 57.00 ( 0.00%) 52.00 ( 8.77%) 52.00 ( 8.77%)
Success 3 Min 84.00 ( 0.00%) 81.00 ( 3.57%) 79.00 ( 5.95%)
Success 3 Mean 85.00 ( 0.00%) 82.40 ( 3.06%) 79.60 ( 6.35%)
Success 3 Max 86.00 ( 0.00%) 83.00 ( 3.49%) 80.00 ( 6.98%)
Patch 3:
3.19-rc4 3.19-rc4 3.19-rc4
8-nothp-1 8-nothp-2 8-nothp-3
Success 1 Min 46.00 ( 0.00%) 44.00 ( 4.35%) 42.00 ( 8.70%)
Success 1 Mean 50.20 ( 0.00%) 45.60 ( 9.16%) 44.00 ( 12.35%)
Success 1 Max 52.00 ( 0.00%) 47.00 ( 9.62%) 47.00 ( 9.62%)
Success 2 Min 53.00 ( 0.00%) 49.00 ( 7.55%) 48.00 ( 9.43%)
Success 2 Mean 55.80 ( 0.00%) 50.60 ( 9.32%) 49.00 ( 12.19%)
Success 2 Max 59.00 ( 0.00%) 52.00 ( 11.86%) 51.00 ( 13.56%)
Success 3 Min 84.00 ( 0.00%) 80.00 ( 4.76%) 79.00 ( 5.95%)
Success 3 Mean 85.40 ( 0.00%) 81.60 ( 4.45%) 80.40 ( 5.85%)
Success 3 Max 87.00 ( 0.00%) 83.00 ( 4.60%) 82.00 ( 5.75%)
While there's no improvement here, I consider reduced fragmentation events
to be worth on its own. Patch 2 also seems to reduce scanning for free
pages, and migrations in compaction, suggesting it has somewhat less work
to do:
Patch 1:
Compaction stalls 4153 3959 3978
Compaction success 1523 1441 1446
Compaction failures 2630 2517 2531
Page migrate success 4600827 4943120 5104348
Page migrate failure 19763 16656 17806
Compaction pages isolated 9597640 10305617 10653541
Compaction migrate scanned 77828948 86533283 87137064
Compaction free scanned 517758295 521312840 521462251
Compaction cost 5503 5932 6110
Patch 2:
Compaction stalls 3800 3450 3518
Compaction success 1421 1316 1317
Compaction failures 2379 2134 2201
Page migrate success 4160421 4502708 4752148
Page migrate failure 19705 14340 14911
Compaction pages isolated 8731983 9382374 9910043
Compaction migrate scanned 98362797 96349194 98609686
Compaction free scanned 496512560 469502017 480442545
Compaction cost 5173 5526 5811
As with v2, /proc/pagetypeinfo appears unaffected with respect to numbers
of unmovable and reclaimable pageblocks.
Configuring the benchmark to allocate like THP page fault (i.e. no sync
compaction) gives much noisier results for iterations 2 and 3 after
reboot. This is not so surprising given how [1] offers lower improvements
in this scenario due to less restarts after deferred compaction which
would change compaction pivot.
Baseline:
3.19-rc4 3.19-rc4 3.19-rc4
5-thp-1 5-thp-2 5-thp-3
Page alloc extfrag event 8148965 6227815 6646741
Extfrag fragmenting 8147872 6227130 6646117
Extfrag fragmenting for unmovable 10324 12942 15975
Extfrag fragmenting unmovable placed with movable 5972 8495 10907
Extfrag fragmenting for reclaimable 601 1707 2210
Extfrag fragmenting reclaimable placed with movable 520 1570 2000
Extfrag fragmenting for movable 8136947 6212481 6627932
Patch 1:
3.19-rc4 3.19-rc4 3.19-rc4
6-thp-1 6-thp-2 6-thp-3
Page alloc extfrag event 8345457 7574471 7020419
Extfrag fragmenting 8343546 7573777 7019718
Extfrag fragmenting for unmovable 10256 18535 30716
Extfrag fragmenting unmovable placed with movable 6893 11726 22181
Extfrag fragmenting for reclaimable 465 1208 1023
Extfrag fragmenting reclaimable placed with movable 353 996 843
Extfrag fragmenting for movable 8332825 7554034 6987979
Patch 2:
3.19-rc4 3.19-rc4 3.19-rc4
7-thp-1 7-thp-2 7-thp-3
Page alloc extfrag event 3512847 3020756 2891625
Extfrag fragmenting 3511940 3020185 2891059
Extfrag fragmenting for unmovable 9017 6892 6191
Extfrag fragmenting unmovable placed with movable 1524 3053 2435
Extfrag fragmenting for reclaimable 445 1081 1160
Extfrag fragmenting reclaimable placed with movable 375 918 986
Extfrag fragmenting for movable 3502478 3012212 2883708
Patch 3:
3.19-rc4 3.19-rc4 3.19-rc4
8-thp-1 8-thp-2 8-thp-3
Page alloc extfrag event 3181699 3082881 2674164
Extfrag fragmenting 3180812 3082303 2673611
Extfrag fragmenting for unmovable 1201 4031 4040
Extfrag fragmenting unmovable placed with movable 974 3611 3645
Extfrag fragmenting for reclaimable 478 1165 1294
Extfrag fragmenting reclaimable placed with movable 387 985 1030
Extfrag fragmenting for movable 3179133 3077107 2668277
The improvements for first iteration are clear, the rest is much noisier
and can appear like regression for Patch 1. Anyway, patch 2 rectifies it.
Allocation success rates are again unaffected so there's no point in
making this e-mail any longer.
[1] http://marc.info/?l=linux-mm&m=142166196321125&w=2
This patch (of 3):
When __rmqueue_fallback() is called to allocate a page of order X, it will
find a page of order Y >= X of a fallback migratetype, which is different
from the desired migratetype. With the help of try_to_steal_freepages(),
it may change the migratetype (to the desired one) also of:
1) all currently free pages in the pageblock containing the fallback page
2) the fallback pageblock itself
3) buddy pages created by splitting the fallback page (when Y > X)
These decisions take the order Y into account, as well as the desired
migratetype, with the goal of preventing multiple fallback allocations
that could e.g. distribute UNMOVABLE allocations among multiple
pageblocks.
Originally, decision for 1) has implied the decision for 3). Commit
47118af076f6 ("mm: mmzone: MIGRATE_CMA migration type added") changed that
(probably unintentionally) so that the buddy pages in case 3) are always
changed to the desired migratetype, except for CMA pageblocks.
Commit fef903efcf0c ("mm/page_allo.c: restructure free-page stealing code
and fix a bug") did some refactoring and added a comment that the case of
3) is intended. Commit 0cbef29a7821 ("mm: __rmqueue_fallback() should
respect pageblock type") removed the comment and tried to restore the
original behavior where 1) implies 3), but due to the previous
refactoring, the result is instead that only 2) implies 3) - and the
conditions for 2) are less frequently met than conditions for 1). This
may increase fragmentation in situations where the code decides to steal
all free pages from the pageblock (case 1)), but then gives back the buddy
pages produced by splitting.
This patch restores the original intended logic where 1) implies 3).
During testing with stress-highalloc from mmtests, this has shown to
decrease the number of events where UNMOVABLE and RECLAIMABLE allocations
steal from MOVABLE pageblocks, which can lead to permanent fragmentation.
In some cases it has increased the number of events when MOVABLE
allocations steal from UNMOVABLE or RECLAIMABLE pageblocks, but these are
fixable by sync compaction and thus less harmful.
Note that evaluation has shown that the behavior introduced by
47118af076f6 for buddy pages in case 3) is actually even better than the
original logic, so the following patch will introduce it properly once
again. For stable backports of this patch it makes thus sense to only fix
versions containing 0cbef29a7821.
[iamjoonsoo.kim@lge.com: tracepoint fix]
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9fbc1f635fd0bd28cb32550211bf095753ac637a upstream.
If __unmap_hugepage_range() tries to unmap the address range over which
hugepage migration is on the way, we get the wrong page because pte_page()
doesn't work for migration entries. This patch simply clears the pte for
migration entries as we do for hwpoison entries.
Fixes: 290408d4a2 ("hugetlb: hugepage migration core")
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a8bda28d87c38c6aa93de28ba5d30cc18e865a11 upstream.
There is a race condition between hugepage migration and
change_protection(), where hugetlb_change_protection() doesn't care about
migration entries and wrongly overwrites them. That causes unexpected
results like kernel crash. HWPoison entries also can cause the same
problem.
This patch adds is_hugetlb_entry_(migration|hwpoisoned) check in this
function to do proper actions.
Fixes: 290408d4a2 ("hugetlb: hugepage migration core")
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9215f437b85da339a7dfe3db6e288637406f88b2 ]
Currently the list is traversed using rcu variant. That is not correct
since dev_set_mac_address can be called which eventually calls
rtmsg_ifinfo_build_skb and there, skb allocation can sleep. So fix this
by remove the rcu usage here.
Fixes: 3d249d4ca7 "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9145736d4862145684009d6a72a6e61324a9439e ]
1. For an IPv4 ping socket, ping_check_bind_addr does not check
the family of the socket address that's passed in. Instead,
make it behave like inet_bind, which enforces either that the
address family is AF_INET, or that the family is AF_UNSPEC and
the address is 0.0.0.0.
2. For an IPv6 ping socket, ping_check_bind_addr returns EINVAL
if the socket family is not AF_INET6. Return EAFNOSUPPORT
instead, for consistency with inet6_bind.
3. Make ping_v4_sendmsg and ping_v6_sendmsg return EAFNOSUPPORT
instead of EINVAL if an incorrect socket address structure is
passed in.
4. Make IPv6 ping sockets be IPv6-only. The code does not support
IPv4, and it cannot easily be made to support IPv4 because
the protocol numbers for ICMP and ICMPv6 are different. This
makes connect(::ffff:192.0.2.1) fail with EAFNOSUPPORT instead
of making the socket unusable.
Among other things, this fixes an oops that can be triggered by:
int s = socket(AF_INET, SOCK_DGRAM, IPPROTO_ICMP);
struct sockaddr_in6 sin6 = {
.sin6_family = AF_INET6,
.sin6_addr = in6addr_any,
};
bind(s, (struct sockaddr *) &sin6, sizeof(sin6));
Change-Id: If06ca86d9f1e4593c0d6df174caca3487c57a241
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit acf8dd0a9d0b9e4cdb597c2f74802f79c699e802 ]
If an over-MTU UDP datagram is sent through a SOCK_RAW socket to a
UFO-capable device, ip_ufo_append_data() sets skb->ip_summed to
CHECKSUM_PARTIAL unconditionally as all GSO code assumes transport layer
checksum is to be computed on segmentation. However, in this case,
skb->csum_start and skb->csum_offset are never set as raw socket
transmit path bypasses udp_send_skb() where they are usually set. As a
result, driver may access invalid memory when trying to calculate the
checksum and store the result (as observed in virtio_net driver).
Moreover, the very idea of modifying the userspace provided UDP header
is IMHO against raw socket semantics (I wasn't able to find a document
clearly stating this or the opposite, though). And while allowing
CHECKSUM_NONE in the UFO case would be more efficient, it would be a bit
too intrusive change just to handle a corner case like this. Therefore
disallowing UFO for packets from SOCK_DGRAM seems to be the best option.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 42c972a1f390e3bc51ca1e434b7e28764992067f ]
The National Instruments USB Host-to-Host Cable is based on the Prolific
PL-25A1 chipset. Add its VID/PID so the plusb driver will recognize it.
Signed-off-by: Ben Shelton <ben.shelton@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2f1d8b9e8afa5a833d96afcd23abcb8cdf8d83ab ]
Brian reported crashes using IPv6 traffic with macvtap/veth combo.
I tracked the crashes in neigh_hh_output()
-> memcpy(skb->data - HH_DATA_MOD, hh->hh_data, HH_DATA_MOD);
Neighbour code assumes headroom to push Ethernet header is
at least 16 bytes.
It appears macvtap has only 14 bytes available on arches
where NET_IP_ALIGN is 0 (like x86)
Effect is a corruption of 2 bytes right before skb->head,
and possible crashes if accessing non existing memory.
This fix should also increase IPv4 performance, as paranoid code
in ip_finish_output2() wont have to call skb_realloc_headroom()
Reported-by: Brian Rak <brak@vultr.com>
Tested-by: Brian Rak <brak@vultr.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d720d8cec563ce4e4fa44a613d4f2dcb1caf2998 ]
With commit a7526eb5d06b (net: Unbreak compat_sys_{send,recv}msg), the
MSG_CMSG_COMPAT flag is blocked at the compat syscall entry points,
changing the kernel compat behaviour from the one before the commit it
was trying to fix (1be374a0518a, net: Block MSG_CMSG_COMPAT in
send(m)msg and recv(m)msg).
On 32-bit kernels (!CONFIG_COMPAT), MSG_CMSG_COMPAT is 0 and the native
32-bit sys_sendmsg() allows flag 0x80000000 to be set (it is ignored by
the kernel). However, on a 64-bit kernel, the compat ABI is different
with commit a7526eb5d06b.
This patch changes the compat_sys_{send,recv}msg behaviour to the one
prior to commit 1be374a0518a.
The problem was found running 32-bit LTP (sendmsg01) binary on an arm64
kernel. Arguably, LTP should not pass 0xffffffff as flags to sendmsg()
but the general rule is not to break user ABI (even when the user
behaviour is not entirely sane).
Fixes: a7526eb5d06b (net: Unbreak compat_sys_{send,recv}msg)
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 57e595631904c827cfa1a0f7bbd7cc9a49da5745 ]
Currently following race is possible in team:
CPU0 CPU1
team_port_del
team_upper_dev_unlink
priv_flags &= ~IFF_TEAM_PORT
team_handle_frame
team_port_get_rcu
team_port_exists
priv_flags & IFF_TEAM_PORT == 0
return NULL (instead of port got
from rx_handler_data)
netdev_rx_handler_unregister
The thing is that the flag is removed before rx_handler is unregistered.
If team_handle_frame is called in between, team_port_exists returns 0
and team_port_get_rcu will return NULL.
So do not check the flag here. It is guaranteed by netdev_rx_handler_unregister
that team_handle_frame will always see valid rx_handler_data pointer.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a4176a9391868bfa87705bcd2e3b49e9b9dd2996 ]
colons are used as a separator in netdev device lookup in dev_ioctl.c
Specific functions are SIOCGIFTXQLEN SIOCETHTOOL SIOCSIFNAME
Signed-off-by: Matthew Thode <mthode@mthode.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 34eea79e2664b314cab6a30fc582fdfa7a1bb1df ]
In tcf_em_validate(), after calling request_module() to load the
kind-specific module, set em->ops to NULL before returning -EAGAIN, so
that module_put() is not called again by tcf_em_tree_destroy().
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 54da5a8be3c1e924c35480eb44c6e9b275f6444e ]
phy_init_eee uses phy_find_setting(phydev->speed, phydev->duplex)
to find a valid entry in the settings array for the given speed
and duplex value. For full duplex 1000baseT, this will return
the first matching entry, which is the entry for 1000baseKX_Full.
If the phy eee does not support 1000baseKX_Full, this entry will not
match, causing phy_init_eee to fail for no good reason.
Fixes: 9a9c56cb34e6 ("net: phy: fix a bug when verify the EEE support")
Fixes: 3e7077067e80c ("phy: Expand phy speed/duplex settings array")
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3e32e733d1bbb3f227259dc782ef01d5706bdae0 ]
ip_check_defrag() may be used by af_packet to defragment outgoing packets.
skb_network_offset() of af_packet's outgoing packets is not zero.
Signed-off-by: Alexander Drozdov <al.drozdov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fba04a9e0c869498889b6445fd06cbe7da9bb834 ]
skb_copy_bits() returns zero on success and negative value on error,
so it is needed to invert the condition in ip_check_defrag().
Fixes: 1bf3751ec90c ("ipv4: ip_check_defrag must not modify skb before unsharing")
Signed-off-by: Alexander Drozdov <al.drozdov@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1c4cff0cf55011792125b6041bc4e9713e46240f ]
The gnet_stats_copy_app() function gets called, more often than not, with its
second argument a pointer to an automatic variable in the caller's stack.
Therefore, to avoid copying garbage afterwards when calling
gnet_stats_finish_copy(), this data is better copied to a dynamically allocated
memory that gets freed after use.
[xiyou.wangcong@gmail.com: remove a useless kfree()]
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7afb8886a05be68e376655539a064ec672de8a8e ]
Ignacy reported that when eth0 is down and add a vlan device
on top of it like:
ip link add link eth0 name eth0.1 up type vlan id 1
We will get a refcount leak:
unregister_netdevice: waiting for eth0.1 to become free. Usage count = 2
The problem is when rtnl_configure_link() fails in rtnl_newlink(),
we simply call unregister_device(), but for stacked device like vlan,
we almost do nothing when we unregister the upper device, more work
is done when we unregister the lower device, so call its ->dellink().
Reported-by: Ignacy Gawedzki <ignacy.gawedzki@green-communications.fr>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3b4711757d7903ab6fa88a9e7ab8901b8227da60 ]
ipv6_cow_metrics() currently assumes only DST_HOST routes require
dynamic metrics allocation from inetpeer. The assumption breaks
when ndisc discovered router with RTAX_MTU and RTAX_HOPLIMIT metric.
Refer to ndisc_router_discovery() in ndisc.c and note that dst_metric_set()
is called after the route is created.
This patch creates the metrics array (by calling dst_cow_metrics_generic) in
ipv6_cow_metrics().
Test:
radvd.conf:
interface qemubr0
{
AdvLinkMTU 1300;
AdvCurHopLimit 30;
prefix fd00:face:face:face::/64
{
AdvOnLink on;
AdvAutonomous on;
AdvRouterAddr off;
};
};
Before:
[root@qemu1 ~]# ip -6 r show | egrep -v unreachable
fd00:face:face:face::/64 dev eth0 proto kernel metric 256 expires 27sec
fe80::/64 dev eth0 proto kernel metric 256
default via fe80::74df:d0ff:fe23:8ef2 dev eth0 proto ra metric 1024 expires 27sec
After:
[root@qemu1 ~]# ip -6 r show | egrep -v unreachable
fd00:face:face:face::/64 dev eth0 proto kernel metric 256 expires 27sec mtu 1300
fe80::/64 dev eth0 proto kernel metric 256 mtu 1300
default via fe80::74df:d0ff:fe23:8ef2 dev eth0 proto ra metric 1024 expires 27sec mtu 1300 hoplimit 30
Fixes: 8e2ec639173f325 (ipv6: don't use inetpeer to store metrics for routes.)
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 364d5716a7adb91b731a35765d369602d68d2881 ]
ifla_vf_policy[] is wrong in advertising its individual member types as
NLA_BINARY since .type = NLA_BINARY in combination with .len declares the
len member as *max* attribute length [0, len].
The issue is that when do_setvfinfo() is being called to set up a VF
through ndo handler, we could set corrupted data if the attribute length
is less than the size of the related structure itself.
The intent is exactly the opposite, namely to make sure to pass at least
data of minimum size of len.
Fixes: ebc08a6f47ee ("rtnetlink: Add VF config code to rtnetlink")
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7744b5f3693cc06695cb9d6667671c790282730f ]
This patch fixes two issues in UDP checksum computation in pktgen.
First, the pseudo-header uses the source and destination IP
addresses. Currently, the ports are used for IPv4.
Second, the UDP checksum covers both header and data. So we need to
generate the data earlier (move pktgen_finalize_skb up), and compute
the checksum for UDP header + data.
Fixes: c26bf4a51308c ("pktgen: Add UDPCSUM flag to support UDP checksums")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
commit 4e7c22d447bb6d7e37bfe39ff658486ae78e8d77 upstream.
The issue is that the stack for processes is not properly randomized on
64 bit architectures due to an integer overflow.
The affected function is randomize_stack_top() in file
"fs/binfmt_elf.c":
static unsigned long randomize_stack_top(unsigned long stack_top)
{
unsigned int random_variable = 0;
if ((current->flags & PF_RANDOMIZE) &&
!(current->personality & ADDR_NO_RANDOMIZE)) {
random_variable = get_random_int() & STACK_RND_MASK;
random_variable <<= PAGE_SHIFT;
}
return PAGE_ALIGN(stack_top) + random_variable;
return PAGE_ALIGN(stack_top) - random_variable;
}
Note that, it declares the "random_variable" variable as "unsigned int".
Since the result of the shifting operation between STACK_RND_MASK (which
is 0x3fffff on x86_64, 22 bits) and PAGE_SHIFT (which is 12 on x86_64):
random_variable <<= PAGE_SHIFT;
then the two leftmost bits are dropped when storing the result in the
"random_variable". This variable shall be at least 34 bits long to hold
the (22+12) result.
These two dropped bits have an impact on the entropy of process stack.
Concretely, the total stack entropy is reduced by four: from 2^28 to
2^30 (One fourth of expected entropy).
This patch restores back the entropy by correcting the types involved
in the operations in the functions randomize_stack_top() and
stack_maxrandom_size().
The successful fix can be tested with:
$ for i in `seq 1 10`; do cat /proc/self/maps | grep stack; done
7ffeda566000-7ffeda587000 rw-p 00000000 00:00 0 [stack]
7fff5a332000-7fff5a353000 rw-p 00000000 00:00 0 [stack]
7ffcdb7a1000-7ffcdb7c2000 rw-p 00000000 00:00 0 [stack]
7ffd5e2c4000-7ffd5e2e5000 rw-p 00000000 00:00 0 [stack]
...
Once corrected, the leading bytes should be between 7ffc and 7fff,
rather than always being 7fff.
Signed-off-by: Hector Marco-Gisbert <hecmargi@upv.es>
Signed-off-by: Ismael Ripoll <iripoll@upv.es>
[ Rebased, fixed 80 char bugs, cleaned up commit message, added test example and CVE ]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Fixes: CVE-2015-1593
Link: http://lkml.kernel.org/r/20150214173350.GA18393@www.outflux.net
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 045c47ca306acf30c740c285a77a4b4bda6be7c5 upstream.
When reading blkio.throttle.io_serviced in a recently created blkio
cgroup, it's possible to race against the creation of a throttle policy,
which delays the allocation of stats_cpu.
Like other functions in the throttle code, just checking for a NULL
stats_cpu prevents the following oops caused by that race.
[ 1117.285199] Unable to handle kernel paging request for data at address 0x7fb4d0020
[ 1117.285252] Faulting instruction address: 0xc0000000003efa2c
[ 1137.733921] Oops: Kernel access of bad area, sig: 11 [#1]
[ 1137.733945] SMP NR_CPUS=2048 NUMA PowerNV
[ 1137.734025] Modules linked in: bridge stp llc kvm_hv kvm binfmt_misc autofs4
[ 1137.734102] CPU: 3 PID: 5302 Comm: blkcgroup Not tainted 3.19.0 #5
[ 1137.734132] task: c000000f1d188b00 ti: c000000f1d210000 task.ti: c000000f1d210000
[ 1137.734167] NIP: c0000000003efa2c LR: c0000000003ef9f0 CTR: c0000000003ef980
[ 1137.734202] REGS: c000000f1d213500 TRAP: 0300 Not tainted (3.19.0)
[ 1137.734230] MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI> CR: 42008884 XER: 20000000
[ 1137.734325] CFAR: 0000000000008458 DAR: 00000007fb4d0020 DSISR: 40000000 SOFTE: 0
GPR00: c0000000003ed3a0 c000000f1d213780 c000000000c59538 0000000000000000
GPR04: 0000000000000800 0000000000000000 0000000000000000 0000000000000000
GPR08: ffffffffffffffff 00000007fb4d0020 00000007fb4d0000 c000000000780808
GPR12: 0000000022000888 c00000000fdc0d80 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 000001003e120200 c000000f1d5b0cc0 0000000000000200 0000000000000000
GPR24: 0000000000000001 c000000000c269e0 0000000000000020 c000000f1d5b0c80
GPR28: c000000000ca3a08 c000000000ca3dec c000000f1c667e00 c000000f1d213850
[ 1137.734886] NIP [c0000000003efa2c] .tg_prfill_cpu_rwstat+0xac/0x180
[ 1137.734915] LR [c0000000003ef9f0] .tg_prfill_cpu_rwstat+0x70/0x180
[ 1137.734943] Call Trace:
[ 1137.734952] [c000000f1d213780] [d000000005560520] 0xd000000005560520 (unreliable)
[ 1137.734996] [c000000f1d2138a0] [c0000000003ed3a0] .blkcg_print_blkgs+0xe0/0x1a0
[ 1137.735039] [c000000f1d213960] [c0000000003efb50] .tg_print_cpu_rwstat+0x50/0x70
[ 1137.735082] [c000000f1d2139e0] [c000000000104b48] .cgroup_seqfile_show+0x58/0x150
[ 1137.735125] [c000000f1d213a70] [c0000000002749dc] .kernfs_seq_show+0x3c/0x50
[ 1137.735161] [c000000f1d213ae0] [c000000000218630] .seq_read+0xe0/0x510
[ 1137.735197] [c000000f1d213bd0] [c000000000275b04] .kernfs_fop_read+0x164/0x200
[ 1137.735240] [c000000f1d213c80] [c0000000001eb8e0] .__vfs_read+0x30/0x80
[ 1137.735276] [c000000f1d213cf0] [c0000000001eb9c4] .vfs_read+0x94/0x1b0
[ 1137.735312] [c000000f1d213d90] [c0000000001ebb38] .SyS_read+0x58/0x100
[ 1137.735349] [c000000f1d213e30] [c000000000009218] syscall_exit+0x0/0x98
[ 1137.735383] Instruction dump:
[ 1137.735405] 7c6307b4 7f891800 409d00b8 60000000 60420000 3d420004 392a63b0 786a1f24
[ 1137.735471] 7d49502a e93e01c8 7d495214 7d2ad214 <7cead02a> e9090008 e9490010 e9290018
And here is one code that allows to easily reproduce this, although this
has first been found by running docker.
void run(pid_t pid)
{
int n;
int status;
int fd;
char *buffer;
buffer = memalign(BUFFER_ALIGN, BUFFER_SIZE);
n = snprintf(buffer, BUFFER_SIZE, "%d\n", pid);
fd = open(CGPATH "/test/tasks", O_WRONLY);
write(fd, buffer, n);
close(fd);
if (fork() > 0) {
fd = open("/dev/sda", O_RDONLY | O_DIRECT);
read(fd, buffer, 512);
close(fd);
wait(&status);
} else {
fd = open(CGPATH "/test/blkio.throttle.io_serviced", O_RDONLY);
n = read(fd, buffer, BUFFER_SIZE);
close(fd);
}
free(buffer);
exit(0);
}
void test(void)
{
int status;
mkdir(CGPATH "/test", 0666);
if (fork() > 0)
wait(&status);
else
run(getpid());
rmdir(CGPATH "/test");
}
int main(int argc, char **argv)
{
int i;
for (i = 0; i < NR_TESTS; i++)
test();
return 0;
}
Reported-by: Ricardo Marin Matinata <rmm@br.ibm.com>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 381cf6587f8a8a8e981bc0c1aaaa8859b51dc756 upstream.
If btrfs_find_item is called with NULL path it allocates one locally but
does not free it. Affected paths are inserting an orphan item for a file
and for a subvol root.
Move the path allocation to the callers.
Fixes: 3f870c289900 ("btrfs: expand btrfs_find_item() to include find_orphan_item functionality")
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5efa0490cc94aee06cd8d282683e22a8ce0a0026 upstream.
This has been confusing people for too long, the message is really just
informative.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 164c24063a3eadee11b46575c5482b2f1417be49 upstream.
sm->offset maybe wrong but magic maybe right, the offset do not have CRC.
Badness at c00c7580 [verbose debug info unavailable]
NIP: c00c7580 LR: c00c718c CTR: 00000014
REGS: df07bb40 TRAP: 0700 Not tainted (2.6.34.13-WR4.3.0.0_standard)
MSR: 00029000 <EE,ME,CE> CR: 22084f84 XER: 00000000
TASK = df84d6e0[908] 'mount' THREAD: df07a000
GPR00: 00000001 df07bbf0 df84d6e0 00000000 00000001 00000000 df07bb58 00000041
GPR08: 00000041 c0638860 00000000 00000010 22084f88 100636c8 df814ff8 00000000
GPR16: df84d6e0 dfa558cc c05adb90 00000048 c0452d30 00000000 000240d0 000040d0
GPR24: 00000014 c05ae734 c05be2e0 00000000 00000001 00000000 00000000 c05ae730
NIP [c00c7580] __alloc_pages_nodemask+0x4d0/0x638
LR [c00c718c] __alloc_pages_nodemask+0xdc/0x638
Call Trace:
[df07bbf0] [c00c718c] __alloc_pages_nodemask+0xdc/0x638 (unreliable)
[df07bc90] [c00c7708] __get_free_pages+0x20/0x48
[df07bca0] [c00f4a40] __kmalloc+0x15c/0x1ec
[df07bcd0] [c01fc880] jffs2_scan_medium+0xa58/0x14d0
[df07bd70] [c01ff38c] jffs2_do_mount_fs+0x1f4/0x6b4
[df07bdb0] [c020144c] jffs2_do_fill_super+0xa8/0x260
[df07bdd0] [c020230c] jffs2_fill_super+0x104/0x184
[df07be00] [c0335814] get_sb_mtd_aux+0x9c/0xec
[df07be20] [c033596c] get_sb_mtd+0x84/0x1e8
[df07be60] [c0201ed0] jffs2_get_sb+0x1c/0x2c
[df07be70] [c0103898] vfs_kern_mount+0x78/0x1e8
[df07bea0] [c0103a58] do_kern_mount+0x40/0x100
[df07bec0] [c011fe90] do_mount+0x240/0x890
[df07bf10] [c0120570] sys_mount+0x90/0xd8
[df07bf40] [c00110d8] ret_from_syscall+0x0/0x4
=== Exception: c01 at 0xff61a34
LR = 0x100135f0
Instruction dump:
38800005 38600000 48010f41 4bfffe1c 4bfc2d15 4bfffe8c 72e90200 4082fc28
3d20c064 39298860 8809000d 68000001 <0f000000> 2f800000 419efc0c 38000001
mount: mounting /dev/mtdblock3 on /common failed: Input/output error
Signed-off-by: Chen Jie <chenjie6@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c510cc83bdbaac8406f4f7caef34f4da0ba35ea upstream.
When DRAM errors occur on memory controllers after EDAC_MAX_MCS (16),
the kernel fatally dereferences unallocated structures, see splat below;
this occurs on at least NumaConnect systems.
Fix by checking if a memory controller info structure was found.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000320
IP: [<ffffffff819f714f>] decode_bus_error+0x2f/0x2b0
PGD 2f8b5a3067 PUD 2f8b5a2067 PMD 0
Oops: 0000 [#2] SMP
Modules linked in:
CPU: 224 PID: 11930 Comm: stream_c.exe.gn Tainted: G D 3.19.0 #1
Hardware name: Supermicro H8QGL/H8QGL, BIOS 3.5b 01/28/2015
task: ffff8807dbfb8c00 ti: ffff8807dd16c000 task.ti: ffff8807dd16c000
RIP: 0010:[<ffffffff819f714f>] [<ffffffff819f714f>] decode_bus_error+0x2f/0x2b0
RSP: 0000:ffff8907dfc03c48 EFLAGS: 00010297
RAX: 0000000000000001 RBX: 9c67400010080a13 RCX: 0000000000001dc6
RDX: 000000001dc61dc6 RSI: ffff8907dfc03df0 RDI: 000000000000001c
RBP: ffff8907dfc03ce8 R08: 0000000000000000 R09: 0000000000000022
R10: ffff891fffa30380 R11: 00000000001cfc90 R12: 0000000000000008
R13: 0000000000000000 R14: 000000000000001c R15: 00009c6740001000
FS: 00007fa97ee18700(0000) GS:ffff8907dfc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000320 CR3: 0000003f889b8000 CR4: 00000000000407e0
Stack:
0000000000000000 ffff8907dfc03df0 0000000000000008 9c67400010080a13
000000000000001c 00009c6740001000 ffff8907dfc03c88 ffffffff810e4f9a
ffff8907dfc03ce8 ffffffff81b375b9 0000000000000000 0000000000000010
Call Trace:
<IRQ>
? vprintk_default
? printk
amd_decode_mce
notifier_call_chain
atomic_notifier_call_chain
mce_log
machine_check_poll
mce_timer_fn
? mce_cpu_restart
call_timer_fn.isra.29
run_timer_softirq
__do_softirq
irq_exit
smp_apic_timer_interrupt
apic_timer_interrupt
<EOI>
? down_read_trylock
__do_page_fault
? __schedule
do_page_fault
page_fault
Signed-off-by: Daniel J Blueman <daniel@numascale.com>
Link: http://lkml.kernel.org/r/1424144078-24589-1-git-send-email-daniel@numascale.com
[ Boris: massage commit message ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d1901ef099c38afd11add4cfb3312c02ef21ec4a upstream.
When a drive is marked write-mostly it should only be the
target of reads if there is no other option.
This behaviour was broken by
commit 9dedf60313fa4dddfd5b9b226a0ef12a512bf9dc
md/raid1: read balance chooses idlest disk for SSD
which causes a write-mostly device to be *preferred* is some cases.
Restore correct behaviour by checking and setting
best_dist_disk and best_pending_disk rather than best_disk.
We only need to test one of these as they are both changed
from -1 or >=0 at the same time.
As we leave min_pending and best_dist unchanged, any non-write-mostly
device will appear better than the write-mostly device.
Reported-by: Tomáš Hodek <tomas.hodek@volny.cz>
Reported-by: Dark Penguin <darkpenguin@yandex.ru>
Signed-off-by: NeilBrown <neilb@suse.de>
Link: http://marc.info/?l=linux-raid&m=135982797322422
Fixes: 9dedf60313fa4dddfd5b9b226a0ef12a512bf9dc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 26ac107378c4742978216be1005b7291b799c7b2 upstream.
Commit a7854487cd7128a30a7f4f5259de9f67d5efb95f:
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
Causes an RCW cycle to be forced even when the array is degraded.
A degraded array cannot support RCW as that requires reading all data
blocks, and one may be missing.
Forcing an RCW when it is not possible causes a live-lock and the code
spins, repeatedly deciding to do something that cannot succeed.
So change the condition to only force RCW on non-degraded arrays.
Reported-by: Manibalan P <pmanibalan@amiindia.co.in>
Bisected-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: a7854487cd7128a30a7f4f5259de9f67d5efb95f
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c2996cb29bfb73927a79dc96e598a718e843f01a upstream.
The KSTK_EIP() and KSTK_ESP() macros should return the user program
counter (PC) and stack pointer (A0StP) of the given task. These are used
to determine which VMA corresponds to the user stack in
/proc/<pid>/maps, and for the user PC & A0StP in /proc/<pid>/stat.
However for Meta the PC & A0StP from the task's kernel context are used,
resulting in broken output. For example in following /proc/<pid>/maps
output, the 3afff000-3b021000 VMA should be described as the stack:
# cat /proc/self/maps
...
100b0000-100b1000 rwxp 00000000 00:00 0 [heap]
3afff000-3b021000 rwxp 00000000 00:00 0
And in the following /proc/<pid>/stat output, the PC is in kernel code
(1074234964 = 0x40078654) and the A0StP is in the kernel heap
(1335981392 = 0x4fa17550):
# cat /proc/self/stat
51 (cat) R ... 1335981392 1074234964 ...
Fix the definitions of KSTK_EIP() and KSTK_ESP() to use
task_pt_regs(tsk)->ctx rather than (tsk)->thread.kernel_context. This
gets the registers from the user context stored after the thread info at
the base of the kernel stack, which is from the last entry into the
kernel from userland, regardless of where in the kernel the task may
have been interrupted, which results in the following more correct
/proc/<pid>/maps output:
# cat /proc/self/maps
...
0800b000-08070000 r-xp 00000000 00:02 207 /lib/libuClibc-0.9.34-git.so
...
100b0000-100b1000 rwxp 00000000 00:00 0 [heap]
3afff000-3b021000 rwxp 00000000 00:00 0 [stack]
And /proc/<pid>/stat now correctly reports the PC in libuClibc
(134320308 = 0x80190b4) and the A0StP in the [stack] region (989864576 =
0x3b002280):
# cat /proc/self/stat
51 (cat) R ... 989864576 134320308 ...
Reported-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Reported-by: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dfcc70a8c868fe03276fa59864149708fb41930b upstream.
For filesystems without separate project quota inode field in the
superblock we just reuse project quota file for group quotas (and vice
versa) if project quota file is allocated and we need group quota file.
When we reuse the file, quota structures on disk suddenly have wrong
type stored in d_flags though. Nobody really cares about this (although
structure type reported to userspace was wrong as well) except
that after commit 14bf61ffe6ac (quota: Switch ->get_dqblk() and
->set_dqblk() to use bytes as space units) assertion in
xfs_qm_scall_getquota() started to trigger on xfs/106 test (apparently I
was testing without XFS_DEBUG so I didn't notice when submitting the
above commit).
Fix the problem by properly resetting ddq->d_flags when running quotacheck
for a quota file.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2f97c20e5f7c3582c7310f65a04465bfb0fd0e85 upstream.
The gpio_chip operations receive a pointer the gpio_chip struct which is
contained in the driver's private struct, yet the container_of call in those
functions point to the mfd struct defined in include/linux/mfd/tps65912.h.
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
node
commit 9cf75e9e4ddd587ac12e88e8751c358b7b27e95f upstream.
The change:
7b8792bbdffdff3abda704f89c6a45ea97afdc62
gpiolib: of: Correct error handling in of_get_named_gpiod_flags
assumed that only one gpio-chip is registred per of-node.
Some drivers register more than one chip per of-node, so
adjust the matching function of_gpiochip_find_and_xlate to
not stop looking for chips if a node-match is found and
the translation fails.
Fixes: 7b8792bbdffd ("gpiolib: of: Correct error handling in of_get_named_gpiod_flags")
Signed-off-by: Hans Holmberg <hans.holmberg@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Tyler Hall <tylerwhall@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9d42d48a342aee208c1154696196497fdc556bbf upstream.
The native (64-bit) sigval_t union contains sival_int (32-bit) and
sival_ptr (64-bit). When a compat application invokes a syscall that
takes a sigval_t value (as part of a larger structure, e.g.
compat_sys_mq_notify, compat_sys_timer_create), the compat_sigval_t
union is converted to the native sigval_t with sival_int overlapping
with either the least or the most significant half of sival_ptr,
depending on endianness. When the corresponding signal is delivered to a
compat application, on big endian the current (compat_uptr_t)sival_ptr
cast always returns 0 since sival_int corresponds to the top part of
sival_ptr. This patch fixes copy_siginfo_to_user32() so that sival_int
is copied to the compat_siginfo_t structure.
Reported-by: Bamvor Jian Zhang <bamvor.zhangjian@huawei.com>
Tested-by: Bamvor Jian Zhang <bamvor.zhangjian@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
