lwn.git/drivers/net/dm9000.c, branch docs-mw

dm9000: Move the Davicom driver

2011-08-13T06:47:14+00:00

Move the Davicom driver into drivers/net/ethernet/davicom/ and make the necessary Kconfig and Makefile changes. CC: Ben Dooks CC: Sascha Hauer Signed-off-by: Jeff Kirsher Acked-by: Sascha Hauer

net: DM9000: Add support for byte EEPROM access

2011-06-11T22:54:52+00:00

Given many versions of ethtool's reluctance to do anything other than byte accesses to the EEPROM interface, it is easier to update the driver to support byte accesses so that all the ethtool versions that have been observed in Debian can write the EEPROM. Signed-off-by: Ben Dooks Signed-off-by: Mark Brown Reviewed-by: Ben Hutchings Signed-off-by: David S. Miller

net: remove interrupt.h inclusion from netdevice.h

2011-06-07T05:55:11+00:00

* remove interrupt.g inclusion from netdevice.h -- not needed * fixup fallout, add interrupt.h and hardirq.h back where needed. Signed-off-by: Alexey Dobriyan Signed-off-by: David S. Miller

net: dm9000: Get the chip in a known good state before enabling interrupts

2011-06-02T04:22:15+00:00

Currently the DM9000 driver requests the primary interrupt before it resets the chip and puts it into a known good state. This means that if the chip is asserting interrupt for some reason we can end up with a screaming IRQ that the interrupt handler is unable to deal with. Avoid this by only requesting the interrupt after we've reset the chip so we know what state it's in. This started manifesting itself on one of my boards in the past month or so, I suspect as a result of some core infrastructure changes removing some form of mitigation against bad behaviour here, even when things boot it seems that the new code brings the interface up more quickly. Signed-off-by: Mark Brown Signed-off-by: David S. Miller

net: dm9000: Fix build

2011-04-18T21:19:32+00:00

Commit c88fcb (net: dm9000: convert to hw_features) broke the build of the dm9000 driver since it merged functions which use different names for the board info structure used for I/O operations without updating all the references to use the same name. Fix that. Signed-off-by: Mark Brown Signed-off-by: David S. Miller

net: dm9000: convert to hw_features

2011-04-15T22:50:40+00:00

Signed-off-by: Michał Mirosław Signed-off-by: David S. Miller

drivers: Final irq namespace conversion

2011-03-29T12:48:19+00:00

Scripted with coccinelle. Signed-off-by: Thomas Gleixner

Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6

2011-03-04T05:27:42+00:00

Conflicts: drivers/net/bnx2x/bnx2x.h

DM9000: Allow randomised ethernet address

2011-02-28T20:42:17+00:00

Allow randomised ethernet address if the device does not have a valid EEPROM or pre-set MAC address. Signed-off-by: Ben Dooks Signed-off-by: Mark Brown Signed-off-by: David S. Miller

DM9000B: Fix PHY power for network down/up

2011-02-23T22:29:50+00:00

DM9000 revision B needs 1 ms delay after PHY power-on. PHY must be powered on by writing 0 into register DM9000_GPR before all other settings will change (see Davicom spec and example code). Remember, that register DM9000_GPR was not changed by reset sequence. Without this fix the FIFO is out of sync and sends wrong data after sequence of "ifconfig ethX down ; ifconfig ethX up". Signed-off-by: David S. Miller