lwn.git/arch/arm/boot/dts/ste-href-tvk1281618.dtsi, branch doc/asciidoc

ARM: ux500: configure the sensors on the TVK board correctly

2015-12-01T13:48:12+00:00

The U8500 HREF TVK board actually has a large set of sensors, with their interrupt lines connected using open drain electronics. Configure the two accelerometers and two magnetometers so we get all sensors to actually probe on boot. Signed-off-by: Linus Walleij

ARM: ux500: replace legacy *,wakeup property with wakeup-source

2015-11-17T08:37:09+00:00

Though the keyboard and other driver will continue to support the legacy "gpio-key,wakeup", "linux,wakeup" boolean property to enable the wakeup source, "wakeup-source" is the new standard binding. This patch replaces all the legacy wakeup properties with the unified "wakeup-source" property in order to avoid any futher copy-paste duplication. Signed-off-by: Sudeep Holla Signed-off-by: Linus Walleij

ARM: ux500: assign the sensor trigger IRQs

2015-05-13T10:22:18+00:00

The ST sensors on the Ux500 boards were not utilizing the IRQs for data ready sample triggers. Enable this by assigning the right GPIO lines and interrupt lines (when the GPIO lines are used for IRQs) to the accelerometer, gyro and magnetometer sensors. Signed-off-by: Linus Walleij

ARM: ux500: fix lsm303dlh magnetometer compat string

2015-05-13T10:22:18+00:00

The magnetometer found on the Ux500 TVK and Snowball boards is a LSM303DLH not a LSM303DLM, small differences but still different. Put in the right compatible strings and things start working smoothly. Signed-off-by: Linus Walleij

pinctrl: nomadik: force-convert to generic config bindings

2014-10-20T07:08:26+00:00

This converts the Nomadik pin controller and all associated device trees to use the standard, generic config bindings for pin controllers. There are no such device trees deployed in the wild so this is safe to do to set a good example. Signed-off-by: Linus Walleij

ARM: ux500: add misc sensors to the device trees

2014-07-07T09:54:07+00:00

This adds the STMicroelectonics MEMS sensor devices to the Ux500 family device trees: - Accelerometer - Magnetometer - Gyroscope - Pressure (barometer) Cc: Lee Jones Cc: Denis CIOCCA Signed-off-by: Linus Walleij

ARM: ux500: move GPIO key configuration to device tree

2013-11-26T20:01:56+00:00

This moves over the configuration of the GPIO keys (used for proximity sensor and Hall effect sensor) from the static pin configuration file to the device tree. As part of the exercise, implement the GPIO keys properly in a per-UIB file as this setup actually differs with each UIB. Signed-off-by: Linus Walleij

ARM: ux500: move GPIO217/218 config to device tree

2013-11-26T20:01:55+00:00

This moves the input-pulled-up setting for GPIO217 as used on the HREFs prior to v60 from the boardfile to the device tree. GPIO218 is only used with the TVK UIB so move it to that .dtsi file. Signed-off-by: Linus Walleij

ARM: ux500: adjust the TC3589x devices to the binding

2013-11-26T20:01:54+00:00

The TC3589x devices appearing in the ST Ericsson device trees are adjusted to use the new binding so this is in a good shape, and we add the keypad on the TVK1281618 UIB so this is working again. Signed-off-by: Linus Walleij

ARM: ux500: register the tc35892 GPIO on the TVK UIB

2013-10-03T08:18:36+00:00

The TVK1281618 UIB has a TC35892 GPIO expander on it, which has in the past probably been confused with the GPIO expander on the older HREF plus previous to v60, which is on an entirely different part of the system with another I2C address. Register the expander in the right place. Signed-off-by: Linus Walleij